Abstract: Series of experimental tests were conducted on a
section of a 660 kW wind turbine blade to measure the pressure
distribution of this model oscillating in plunging motion. In order to
minimize the amount of data required to predict aerodynamic loads
of the airfoil, a General Regression Neural Network, GRNN, was
trained using the measured experimental data. The network once
proved to be accurate enough, was used to predict the flow behavior
of the airfoil for the desired conditions.
Results showed that with using a few of the acquired data, the
trained neural network was able to predict accurate results with
minimal errors when compared with the corresponding measured
values. Therefore with employing this trained network the
aerodynamic coefficients of the plunging airfoil, are predicted
accurately at different oscillation frequencies, amplitudes, and angles
of attack; hence reducing the cost of tests while achieving acceptable
accuracy.
Abstract: In this paper the supersonic ejectors are
experimentally and analytically studied. Ejector is a device that
uses the energy of a fluid to move another fluid. This device works
like a vacuum pump without usage of piston, rotor or any other
moving component. An ejector contains an active nozzle, a passive
nozzle, a mixing chamber and a diffuser. Since the fluid viscosity
is large, and the flow is turbulent and three dimensional in the
mixing chamber, the numerical methods consume long time and
high cost to analyze the flow in ejectors. Therefore this paper
presents a simple analytical method that is based on the precise
governing equations in fluid mechanics. According to achieved
analytical relations, a computer code has been prepared to analyze
the flow in different components of the ejector. An experiment has
been performed in supersonic regime 1.5
Abstract: All-to-all personalized communication, also known as complete exchange, is one of the most dense communication patterns in parallel computing. In this paper, we propose new indirect algorithms for complete exchange on all-port ring and torus. The new algorithms fully utilize all communication links and transmit messages along shortest paths to completely achieve the theoretical lower bounds on message transmission, which have not be achieved among other existing indirect algorithms. For 2D r × c ( r % c ) all-port torus, the algorithm has time complexities of optimal transmission cost and O(c) message startup cost. In addition, the proposed algorithms accommodate non-power-of-two tori where the number of nodes in each dimension needs not be power-of-two or square. Finally, the algorithms are conceptually simple and symmetrical for every message and every node so that they can be easily implemented and achieve the optimum in practice.
Abstract: Today, design requirements are extending more and
more from electronic (analogue and digital) to multidiscipline design.
These current needs imply implementation of methodologies to make
the CAD product reliable in order to improve time to market, study
costs, reusability and reliability of the design process.
This paper proposes a high level design approach applied for the
characterization and the optimization of Switched-Current Sigma-
Delta Modulators. It uses the new hardware description language
VHDL-AMS to help the designers to optimize the characteristics of
the modulator at a high level with a considerably reduced CPU time
before passing to a transistor level characterization.
Abstract: This paper presents an adaptive motion estimator
that can be dynamically reconfigured by the best algorithm
depending on the variation of the video nature during the lifetime
of an application under running. The 4 Step Search (4SS) and the
Gradient Search (GS) algorithms are integrated in the estimator in
order to be used in the case of rapid and slow video sequences
respectively. The Full Search Block Matching (FSBM) algorithm
has been also integrated in order to be used in the case of the
video sequences which are not real time oriented.
In order to efficiently reduce the computational cost while
achieving better visual quality with low cost power, the proposed
motion estimator is based on a Variable Block Size (VBS) scheme
that uses only the 16x16, 16x8, 8x16 and 8x8 modes.
Experimental results show that the adaptive motion estimator
allows better results in term of Peak Signal to Noise Ratio
(PSNR), computational cost, FPGA occupied area, and dissipated
power relatively to the most popular variable block size schemes
presented in the literature.
Abstract: Freeze concentration freezes or crystallises the water
molecules out as ice crystals and leaves behind a highly concentrated
solution. In conventional suspension freeze concentration where ice
crystals formed as a suspension in the mother liquor, separation of
ice is difficult. The size of the ice crystals is still very limited which
will require usage of scraped surface heat exchangers, which is very
expensive and accounted for approximately 30% of the capital cost.
This research is conducted using a newer method of freeze
concentration, which is progressive freeze concentration. Ice crystals
were formed as a layer on the designed heat exchanger surface. In
this particular research, a helical structured copper crystallisation
chamber was designed and fabricated. The effect of two operating
conditions on the performance of the newly designed crystallisation
chamber was investigated, which are circulation flowrate and coolant
temperature. The performance of the design was evaluated by the
effective partition constant, K, calculated from the volume and
concentration of the solid and liquid phase. The system was also
monitored by a data acquisition tool in order to see the temperature
profile throughout the process. On completing the experimental
work, it was found that higher flowrate resulted in a lower K, which
translated into high efficiency. The efficiency is the highest at 1000
ml/min. It was also found that the process gives the highest
efficiency at a coolant temperature of -6 °C.
Abstract: It is well known that the channel capacity of Multiple-
Input-Multiple-Output (MIMO) system increases as the number of
antenna pairs between transmitter and receiver increases but it suffers
from multiple expensive RF chains. To reduce the cost of RF chains,
Antenna Selection (AS) method can offer a good tradeoff between
expense and performance. In a transmitting AS system, Channel
State Information (CSI) feedback is necessarily required to choose
the best subset of antennas in which the effects of delays and errors
occurred in feedback channels are the most dominant factors
degrading the performance of the AS method. This paper presents the
concept of AS method using CSI from channel reciprocity instead of
feedback method. Reciprocity technique can easily archive CSI by
utilizing a reverse channel where the forward and reverse channels
are symmetrically considered in time, frequency and location. In this
work, the capacity performance of MIMO system when using AS
method at transmitter with reciprocity channels is investigated by
own developing Testbed. The obtained results show that reciprocity
technique offers capacity close to a system with a perfect CSI and
gains a higher capacity than a system without AS method from 0.9 to
2.2 bps/Hz at SNR 10 dB.
Abstract: Multi-Radio Multi-Channel Wireless Mesh Networks (MRMC-WMNs) operate at the backbone to access and route high volumes of traffic simultaneously. Such roles demand high network capacity, and long “online" time at the expense of accelerated transmission energy depletion and poor connectivity. This is the problem of transmission power control. Numerous power control methods for wireless networks are in literature. However, contributions towards MRMC configurations still face many challenges worth considering. In this paper, an energy-efficient power selection protocol called PMMUP is suggested at the Link-Layer. This protocol first divides the MRMC-WMN into a set of unified channel graphs (UCGs). A UCG consists of multiple radios interconnected to each other via a common wireless channel. In each UCG, a stochastic linear quadratic cost function is formulated. Each user minimizes this cost function consisting of trade-off between the size of unification states and the control action. Unification state variables come from independent UCGs and higher layers of the protocol stack. The PMMUP coordinates power optimizations at the network interface cards (NICs) of wireless mesh routers. The proposed PMMUP based algorithm converges fast analytically with a linear rate. Performance evaluations through simulations confirm the efficacy of the proposed dynamic power control.
Abstract: This paper presents a new problem solving approach
that is able to generate optimal policy solution for finite-state
stochastic sequential decision-making problems with high data
efficiency. The proposed algorithm iteratively builds and improves
an approximate Markov Decision Process (MDP) model along with
cost-to-go value approximates by generating finite length trajectories
through the state-space. The approach creates a synergy between an
approximate evolving model and approximate cost-to-go values to
produce a sequence of improving policies finally converging to the
optimal policy through an intelligent and structured search of the
policy space. The approach modifies the policy update step of the
policy iteration so as to result in a speedy and stable convergence to
the optimal policy. We apply the algorithm to a non-holonomic
mobile robot control problem and compare its performance with
other Reinforcement Learning (RL) approaches, e.g., a) Q-learning,
b) Watkins Q(λ), c) SARSA(λ).
Abstract: Sedimentation process resulting from soil erosion in
the water basin especially in arid and semi-arid where poor
vegetation cover in the slope of the mountains upstream could
contribute to sediment formation. The consequence of sedimentation
not only makes considerable change in the morphology of the river
and the hydraulic characteristics but would also have a major
challenge for the operation and maintenance of the canal network
which depend on water flow to meet the stakeholder-s requirements.
For this reason mathematical modeling can be used to simulate the
effective factors on scouring, sediment transport and their settling
along the waterways. This is particularly important behind the
reservoirs which enable the operators to estimate the useful life of
these hydraulic structures. The aim of this paper is to simulate the
sedimentation and erosion in the eastern and western water intake
structures of the Dez Diversion weir using GSTARS-3 software. This
is done to estimate the sedimentation and investigate the ways in
which to optimize the process and minimize the operational
problems. Results indicated that the at the furthest point upstream of
the diversion weir, the coarser sediment grains tended to settle. The
reason for this is the construction of the phantom bridge and the
outstanding rocks just upstream of the structure. The construction of
these along the river course has reduced the momentum energy
require to push the sediment loads and make it possible for them to
settle wherever the river regime allows it. Results further indicated a
trend for the sediment size in such a way that as the focus of study
shifts downstream the size of grains get smaller and vice versa. It
was also found that the finding of the GSTARS-3 had a close
proximity with the sets of the observed data. This suggests that the
software is a powerful analytical tool which can be applied in the
river engineering project with a minimum of costs and relatively
accurate results.
Abstract: In this paper, the periodic surveillance scheme has
been proposed for any convex region using mobile wireless sensor
nodes. A sensor network typically consists of fixed number of
sensor nodes which report the measurements of sensed data such as
temperature, pressure, humidity, etc., of its immediate proximity
(the area within its sensing range). For the purpose of sensing an
area of interest, there are adequate number of fixed sensor
nodes required to cover the entire region of interest. It implies
that the number of fixed sensor nodes required to cover a given
area will depend on the sensing range of the sensor as well as
deployment strategies employed. It is assumed that the sensors to
be mobile within the region of surveillance, can be mounted on
moving bodies like robots or vehicle. Therefore, in our
scheme, the surveillance time period determines the number of
sensor nodes required to be deployed in the region of interest.
The proposed scheme comprises of three algorithms namely:
Hexagonalization, Clustering, and Scheduling, The first algorithm
partitions the coverage area into fixed sized hexagons that
approximate the sensing range (cell) of individual sensor node.
The clustering algorithm groups the cells into clusters, each of
which will be covered by a single sensor node. The later
determines a schedule for each sensor to serve its respective cluster.
Each sensor node traverses all the cells belonging to the cluster
assigned to it by oscillating between the first and the last cell for
the duration of its life time. Simulation results show that our
scheme provides full coverage within a given period of time using
few sensors with minimum movement, less power consumption,
and relatively less infrastructure cost.
Abstract: Anti-money laundering is commonly recognized as a
set of procedures, laws or regulations designed to reduce the practice
of generating income through illegal actions. In Malaysia, the
government and law enforcement agencies have stepped up their
capacities and efforts to curb money laundering since 2001. One of
these measures was the enactment of the Anti-Money Laundering
Act (AMLA) in 2001. The implementation costs on anti-money
laundering requirements (AMLR) can be burdensome to those who
are involved in enforcing them. The objective of this paper is to
explore the perceived effectiveness of AMLR from the enforcement
agencies- perspective. This is a preliminary study whose findings
will help to give direction for further AML research in Malaysia. In
addition, the results of this study provide empirical evidences on the
perceived effectiveness of AMLR prior to further investigations on
barriers and improvements of the implementation of the anti-money
laundering regime in Malaysia.
Abstract: Contact centres have been exemplars of scientific management in the discipline of operations management for more than a decade now. With the movement of industries from a resource based economy to knowledge based economy businesses have started to realize the customer eccentricity being the key to sustainability amidst high velocity of the market. However, as technologies have converged and advanced, so have the contact centres. Contact Centres have redirected the supply chains and the concept of retailing is highly diminished due to over exaggeration of cost reduction strategies. In conditions of high environmental velocity together with services featuring considerable information intensity contact centres will require up to date and enlightened agents to satisfy the demands placed upon them by those requesting their services. In this paper we examine salient factors such as Power Distance, Knowledge structures and the dynamics of job specialisation and enlargement to suggest critical success factors in the domain of contact centres.
Abstract: Flash memory has become an important storage device
in many embedded systems because of its high performance, low
power consumption and shock resistance. Multi-level cell (MLC) is
developed as an effective solution for reducing the cost and increasing
the storage density in recent years. However, most of flash file system
cannot handle the error correction sufficiently. To correct more errors
for MLC, we implement Reed-Solomon (RS) code to YAFFS, what is
widely used for flash-based file system. RS code has longer computing
time but the correcting ability is much higher than that of Hamming
code.
Abstract: The OTOP Entrepreneurship that used to create
substantial source of income for local Thai communities are now in a
stage of exigent matters that required assistances from public sectors
due to over Entrepreneurship of duplicative ideas, unable to adjust
costs and prices, lack of innovation, and inadequate of quality
control. Moreover, there is a repetitive problem of middlemen who
constantly corner the OTOP market. Local OTOP producers become
easy preys since they do not know how to add more values, how to
create and maintain their own brand name, and how to create proper
packaging and labeling. The suggested solutions to local OTOP
producers are to adopt modern management techniques, to find
knowhow to add more values to products and to unravel other
marketing problems. The objectives of this research are to study the
prevalent OTOP products management and to discover direction to
manage OTOP products to enhance the effectiveness of OTOP
Entrepreneurship in Nonthaburi Province, Thailand. There were 113
participants in this study. The research tools can be divided into two
parts: First part is done by questionnaire to find responses of the
prevalent OTOP Entrepreneurship management. Second part is the
use of focus group which is conducted to encapsulate ideas and local
wisdom. Data analysis is performed by using frequency, percentage,
mean, and standard deviation as well as the synthesis of several small
group discussions. The findings reveal that 1) Business Resources:
the quality of product is most important and the marketing of product
is least important. 2) Business Management: Leadership is most
important and raw material planning is least important. 3) Business
Readiness: Communication is most important and packaging is least
important. 4) Support from public sector: Certified from the
government is most important and source of raw material is the least
important.
Abstract: Cooling with sound is a physical phenomenon allowed by Thermo-Acoustics in which acoustic energy is transformed into a negative heat transfer, in other words: into cooling! Without needing any harmful gas, the transformation is environmentally friendly and can respond to many needs in terms of air conditioning, food refrigeration for domestic use, and cooling medical samples for example. To explore the possibilities of this cooling solution on a small scale, the TACS prototype has been designed, consisting of a low cost thermoacoustic refrigerant “pipe” able to lower the temperature by a few degrees. The obtained results are providing an interesting element for possible future of thermo-acoustic refrigeration.
Abstract: Development of a Robust Supply Chain for Dynamic
Operating Environment as we move further into the twenty first
century, organisations are under increasing pressure to deliver a high
product variation at a reasonable cost without compromise in quality.
In a number of cases this will take the form of a customised or high
variety low volume manufacturing system that requires prudent
management of resources, among a number of functions, to achieve
competitive advantage. Purchasing and Supply Chain management is
one of such function and due to the substantial interaction with
external elements needs to be strategically managed. This requires a
number of primary and supporting tools that will enable the
appropriate decisions to be made rapidly. This capability is
especially vital in a dynamic environment as it provides a pivotal role
in increasing the profit margin of the product. The management of
this function can be challenging by itself and even more for Small
and Medium Enterprises (SMEs) due to the limited resources and
expertise available at their disposal.
This paper discusses the development of tools and concepts
towards effectively managing the purchasing and supply chain
function. The developed tools and concepts will provide a cost
effective way of managing this function within SMEs. The paper
further shows the use of these tools within Contechs, a manufacturer
of luxury boat interiors, and the associated benefits achieved as a
result of this implementation. Finally a generic framework towards
use in such environments is presented.
Abstract: The aim of the current work is to present a comparison among three popular optimization methods in the inverse elastostatics problem (IESP) of flaw detection within a solid. In more details, the performance of a simulated annealing, a Hooke & Jeeves and a sequential quadratic programming algorithm was studied in the test case of one circular flaw in a plate solved by both the boundary element (BEM) and the finite element method (FEM). The proposed optimization methods use a cost function that utilizes the displacements of the static response. The methods were ranked according to the required number of iterations to converge and to their ability to locate the global optimum. Hence, a clear impression regarding the performance of the aforementioned algorithms in flaw identification problems was obtained. Furthermore, the coupling of BEM or FEM with these optimization methods was investigated in order to track differences in their performance.
Abstract: This paper presents an efficient VLSI architecture
design to achieve real time video processing using Full-Search Block
Matching (FSBM) algorithm. The design employs parallel bank
architecture with minimum latency, maximum throughput, and full
hardware utilization. We use nine parallel processors in our
architecture and each controlled by a state machine. State machine
control implementation makes the design very simple and cost
effective. The design is implemented using VHDL and the
programming techniques we incorporated makes the design
completely programmable in the sense that the search ranges and the
block sizes can be varied to suit any given requirements. The design
can operate at frequencies up to 36 MHz and it can function in QCIF
and CIF video resolution at 1.46 MHz and 5.86 MHz, respectively.
Abstract: In this paper we present the PC cluster built at R.V.
College of Engineering (with great help from the Department of
Computer Science and Electrical Engineering). The structure of the
cluster is described and the performance is evaluated by rendering of
complex 3D Persistence of Vision (POV) images by the Ray-Tracing
algorithm. Here, we propose an unexampled method to render such
images, distributedly on a low cost scalable.