Abstract: Stable bacterial polymorphism on a single limiting resource may appear if between the evolved strains metabolic interactions take place that allow the exchange of essential nutrients [8]. Towards an attempt to predict the possible outcome of longrunning evolution experiments, a network based on the metabolic capabilities of homogeneous populations of every single gene knockout strain (nodes) of the bacterium E. coli is reconstructed. Potential metabolic interactions (edges) are allowed only between strains of different metabolic capabilities. Bacterial communities are determined by finding cliques in this network. Growth of the emerged hypothetical bacterial communities is simulated by extending the metabolic flux balance analysis model of Varma et al [2] to embody heterogeneous cell population growth in a mutual environment. Results from aerobic growth on 10 different carbon sources are presented. The upper bounds of the diversity that can emerge from single-cloned populations of E. coli such as the number of strains that appears to metabolically differ from most strains (highly connected nodes), the maximum clique size as well as the number of all the possible communities are determined. Certain single gene deletions are identified to consistently participate in our hypothetical bacterial communities under most environmental conditions implying a pattern of growth-condition- invariant strains with similar metabolic effects. Moreover, evaluation of all the hypothetical bacterial communities under growth on pyruvate reveals heterogeneous populations that can exhibit superior growth performance when compared to the performance of the homogeneous wild-type population.
Abstract: This paper details a new concept of using compressed air as a potential zero pollution power source for motorbikes. In place of an internal combustion engine, the motorbike is equipped with an air turbine transforms the energy of the compressed air into shaft work. The mathematical modeling and performance evaluation of a small capacity compressed air driven vaned type novel air turbine is presented in this paper. The effect of isobaric admission and adiabatic expansion of high pressure air for different rotor diameters, casing diameters and ratio of rotor to casing diameters of the turbine have been considered and analyzed. It is concluded that the work output is found optimum for some typical values of rotor / casing diameter ratios. In this study, the maximum power works out to 3.825 kW (5.20 HP) for casing diameter of 200 mm and rotor to casing diameter ratio of 0.65 to 0.60 which is sufficient to run motorbike.
Abstract: This study was aimed to study the probability about
the production of fiberboard made of durian rind through latex with
phenolic resin as binding agent. The durian rind underwent the
boiling process with NaOH [7], [8] and then the fiber from durian
rind was formed into fiberboard through heat press. This means that
durian rind could be used as replacement for plywood in plywood
industry by using durian fiber as composite material with adhesive
substance. This research would study the probability about the
production of fiberboard made of durian rind through latex with
phenolic resin as binding agent. At first, durian rind was split,
exposed to light, boiled and steamed in order to gain durian fiber.
Then, fiberboard was tested with the density of 600 Kg/m3 and 800
Kg/m3. in order to find a suitable ratio of durian fiber and latex.
Afterwards, mechanical properties were tested according to the
standards of ASTM and JIS A5905-1994. After the suitable ratio was
known, the test results would be compared with medium density
fiberboard (MDF) and other related research studies. According to
the results, fiberboard made of durian rind through latex with
phenolic resin at the density of 800 Kg/m3 at ratio of 1:1, the
moisture was measured to be 5.05% with specific gravity (ASTM D
2395-07a) of 0.81, density (JIS A 5905-1994) of 0.88 g/m3, tensile
strength, hardness (ASTM D2240), flexibility or elongation at break
yielded similar values as the ones by medium density fiberboard
(MDF).
Abstract: Route bus system is the fundamental public transportation
system and has an important role in every province. To improve
the usability of it greatly, we develop an AR application for "Bus-
Net". The Bus-Net system is the shortest path planning system.
Bus-Net supports bus users to make a plan to change buses by
providing them with information about the direction. However, with
Bus-Net, these information are provided in text-base. It is difficult
to understand them for the person who does not know the place. We
developed the AR application for Bus-Net. It supports the action of
a bus user in an innovative way by putting information on a camera
picture and leading the way to a bus stop. The application also inform
the user the correct bus to get, the direction the bus takes and the
fare, which ease many anxieties and worries people tend to feel when
they take buses.
Abstract: Since its independence in 1962, Algeria has struggled
to establish an educational system tailored to the needs of the
population it may address. Considering the historical connection with
France, Algeria has always looked at the French language as a
cultural imperative until late in the seventies. After the Arabization
policy of 1971 and the socioeconomic changes taking place
worldwide, the use of English as a communicating vehicle started to
gain more space within globalized Algeria. Consequently, disparities
in the use of French started to fade away at the cross-roads leaving
more space to the teaching of English as a second foreign language.
Moreover, the introduction of the Bologna Process and the
European Credit Transfer System in Higher Education has
necessitated some innovations in the design and development of new
curricula adapted to the socioeconomic market. In this paper, I will
try to highlight the important historical dimensions Algeria has taken
towards the implementation of an English language methodology and
to the status it acquired from second foreign language, to first foreign
language to “the language of knowledge and sciences". I will also
propose new pedagogical perspectives for a better treatment of the
English language in order to encourage independent and autonomous
learning.
Abstract: When the crisscross baffles and logarithmic spiral
baffles are placed on the bottom of the stirred tank with elliptic
bottom, using CFD software FLUENT simulates the velocity field of
the stirred tank with elliptic bottom and bottom baffles. Compare the
velocity field of stirred tank with bottom crisscross baffle to the
velocity field of stirred tank without bottom baffle and analysis the
flow pattern on the same axis-section and different cross-sections. The
sizes of the axial and radial velocity are compared respectively when
the stirred tank with bottom crisscross baffles, bottom logarithmic
spiral baffles and without bottom baffle. At the same time, the
numerical calculations of mixing power are compared when the stirred
tank with bottom crisscross baffles and bottom logarithmic spiral
baffles. Research shows that bottom crisscross baffles and logarithmic
spiral baffles have a great impact on flow pattern within the reactor
and improve the mixing effect better than without baffle. It also has
shown that bottom logarithmic spiral baffles has lower power
consumption than bottom crisscross baffles.
Abstract: Carbon fibers have specific characteristics in
comparison with industrial and structural materials used in different
applications. Special properties of carbon fibers make them attractive
for reinforcing and fabrication of composites. These fibers have been
utilized for composites of metals, ceramics and plastics. However,
it-s mainly used in different forms to reinforce lightweight polymer
materials such as epoxy resin, polyesters or polyamides. The
composites of carbon fiber are stronger than steel, stiffer than
titanium, and lighter than aluminum and nowadays they are used in a
variety of applications. This study explains applications of carbon
fibers in different fields such as space, aviation, transportation,
medical, construction, energy, sporting goods, electronics, and the
other commercial/industrial applications. The last findings of
composites with polymer, metal and ceramic matrices containing
carbon fibers and their applications in the world investigated.
Researches show that carbon fibers-reinforced composites due to
unique properties (including high specific strength and specific
modulus, low thermal expansion coefficient, high fatigue strength,
and high thermal stability) can be replaced with common industrial
and structural materials.
Abstract: In this article, biomechanical aspects of hen-s eggshell as a natural ceramic structure are studied. The images, taken by a scanning electron microscope (SEM), are used to investigate the microscopic aspects of the egg. It is observed that eggshell has a three-layered microstructure with different morphological and structural characteristics. Studies on the eggshell membrane (ESM) as a prosperous tissue suggest that it is placed to prevent the penetration of microorganisms into the egg. Finally, numerical models of the egg are presented to study the stress distribution and its deformation under different loading conditions. The effects of two different types of loading (hydrostatic and point loadings) on two different shell models (with constant and variable thicknesses) are investigated in detail.
Abstract: We investigated a modified thermal evaporation
method in the growth process of ZnO nanowires. ZnO nanowires
were fabricated on p-type silicon substrates without using a metal
catalyst. A simple horizontal double-tube system along with
chemical vapor diffusion of the precursor was used to grow the ZnO
nanowires. The substrates were placed in different temperature
zones, and ZnO nanowires with different diameters were obtained for
the different substrate temperatures. In addition to the nanowires,
ZnO microdiscs with different diameters were obtained on another
substrate, which was placed at a lower temperature than the other
substrates. The optical properties and crystalline quality of the ZnO
nanowires and microdiscs were characterized by room temperature
photoluminescence (PL) and Raman spectrometers. The PL and
Raman studies demonstrated that the ZnO nanowires and microdiscs
grown using such set-up had good crystallinity with excellent optical
properties. Rectifying behavior of ZnO/Si heterostructures was
characterized by a simple DC circuit.
Abstract: This paper shows the advantages of the material failure process simulation by improve finite elements with embedded discontinuities, using a new definition of traction vector, dependent on the discontinuity length and the angle. Particularly, two families of this kind of elements are compared: kinematically optimal symmetric and statically and kinematically optimal non-symmetric. The constitutive model to describe the behavior of the material in the symmetric formulation is a traction-displacement jump relationship equipped with softening after reaching the failure surface.
To show the validity of this symmetric formulation, representative numerical examples illustrating the performance of the proposed formulation are presented. It is shown that the non-symmetric family may over or underestimate the energy required to create a discontinuity, as this effect is related with the total length of the discontinuity, fact that is not noticed when the discontinuity path is a straight line.
Abstract: Oxide scale thickness measurements are used in assessing the life of different components operating at high temperature environment. Such measurements provide an approximation for the temperature inside components such as reheater and superheater tubes. A number of failures were encountered in one of the boilers in one of Kuwaiti power plants. These failure were mainly in the first row of the primary super heater tubes, therefore, the specialized engineer decide to replace them during the annual shutdown. As a tool for failure analysis, oxide scale thickness measurement were used to investigate the temperature distribution in these tubes. In this paper, the oxide scale thickness of these tubes were measured and used for analysis. The measurements provide an illustration of the distribution of heat transfer of the primary superheater tubes in the boiler system. Remarks and analysis about the design of the boiler are also provided.
Abstract: Aim. We have introduced the notion of order to multinormed spaces and countable union spaces and their duals. The topology of bounded convergence is assigned to the dual spaces. The aim of this paper is to develop the theory of ordered topological linear
spaces La,b, L(w, z), the dual spaces of ordered multinormed spaces
La,b, ordered countable union spaces L(w, z), with the topology of bounded convergence assigned to the dual spaces. We apply Laplace transformation to the ordered linear space of Laplace transformable
generalized functions. We ultimately aim at finding solutions to nonhomogeneous
nth order linear differential equations with constant
coefficients in terms of generalized functions and comparing different
solutions evolved out of different initial conditions.
Method. The above aim is achieved by
• Defining the spaces La,b, L(w, z).
• Assigning an order relation on these spaces by identifying a
positive cone on them and studying the properties of the cone.
• Defining an order relation on the dual spaces La,b, L(w, z) of La,b, L(w, z) and assigning a topology to these dual spaces which makes the order dual and the topological dual the same. • Defining the adjoint of a continuous map on these spaces
and studying its behaviour when the topology of bounded
convergence is assigned to the dual spaces.
• Applying the two-sided Laplace Transformation on the ordered
linear space of generalized functions W and studying some
properties of the transformation which are used in solving
differential equations.
Result. The above techniques are applied to solve non-homogeneous
n-th order linear differential equations with constant coefficients in
terms of generalized functions and to compare different solutions of the differential equation.
Abstract: In this paper we introduce a new unit test technique
called déjà-vu object. Déjà-vu objects replace real objects used by
classes under test, allowing the execution of isolated unit tests. A
déjà-vu object is able to observe and record the behaviour of a real
object during real sessions, and to replace it during unit tests,
returning previously recorded results. Consequently déjà-vu object
technique can be useful when a bottom-up development and testing
strategy is adopted. In this case déjà-vu objects can increase test
portability and test source code readability. At the same time they
can reduce the time spent by programmers to develop test code and
the risk of incompatibility during the switching between déjà-vu and
production code.
Abstract: Liveable city is referred to as the quality of life in an
area that contributes towards a safe, healthy and enjoyable place. This
paper discusses the role of the streets- activities in making Kuala
Lumpur a liveable city and the happiness level of the residents
towards the city-s street activities. The study was conducted using the
residents of Kuala Lumpur. A mixed method technique is used with
the quantitative data as a main data and supported by the qualitative
data. Data were collected using questionnaires, observation and also
an interview session with a sample of residents of Kuala Lumpur.
The sampling technique is based on multistage cluster data sampling.
The findings revealed that, there is still no significant relationship
between the length of stay of the resident in Kuala Lumpur with the
happiness level towards the street activities that occurred in the city.
Abstract: Overhead conveyor systems are in use in many installations around the world, meeting the widest range of applications possible. Overhead conveyor systems are particularly preferred in automotive industry but also at post offices. Overhead conveyor systems must always be integrated with a logistical process by finding the best way for a cheaper material flow in order to guarantee precise and fast workflows. With their help, any transport can take place without wasting ground and space, without excessive company capacity, lost or damaged products, erroneous delivery, endless travels and without wasting time. Ultra-light overhead conveyor systems are rope-based conveying systems with individually driven vehicles. The vehicles can move automatically on the rope and this can be realized by energy and signals. Crossings are realized by switches. Ultra-light overhead conveyor systems provide optimal material flow, which produces profit and saves time. This article introduces two new ultra-light overhead conveyor designs in logistics and explains their components. According to the explanation of the components, scenarios are created by means of their technical characteristics. The scenarios are visualized with the help of CAD software. After that, assumptions are made for application area. According to these assumptions scenarios are visualized. These scenarios help logistics companies achieve lower development costs as well as quicker market maturity.
Abstract: The flexible follower response of a translating cam with
four different profiles for rise-dwell-fall-dwell (RDFD) motion is
investigated. The cycloidal displacement motion, the modified
sinusoidal acceleration motion, the modified trapezoidal acceleration
motion, and the 3-4-5 polynomial motion are employed to describe the
rise and the fall motions of the follower and the associated four kinds of
cam profiles are studied. Since the follower flexibility is considered,
the contact point of the roller and the cam is an unknown. Two
geometric constraints formulated to restrain the unknown position are
substituted into Hamilton-s principle with Lagrange multipliers.
Applying the assumed mode method, one can obtain the governing
equations of motion as non-linear differential-algebraic equations. The
equations are solved using Runge-Kutta method. Then, the responses of
the flexible follower undergoing the four different motions are
investigated in time domain and in frequency domain.
Abstract: The evaluation of energy release rate and centre Crack
Opening Displacement (COD) for circumferential Through-Wall
Cracked (TWC) pipes is an important issue in the assessment of
critical crack length for unstable fracture. The ability to predict crack
growth continues to be an important component of research for
several structural materials. Crack growth predictions can aid the
understanding of the useful life of a structural component and the
determination of inspection intervals and criteria. In this context,
studies were carried out at CSIR-SERC on Nuclear Power Plant
(NPP) piping components subjected to monotonic as well as cyclic
loading to assess the damage for crack growth due to low-cycle
fatigue in circumferentially TWC pipes.
Abstract: In this work, the results of mixing study by a jet mixer in a tank have been investigated in the laboratory scale. The tank dimensions are H/D=1 and the jet entrance have been considered in
the center of upper surface of tank. RNG-k-ε model is used as the
turbulent model for the prediction of the pattern of turbulent flow
inside the tank. For this purpose, a tank with volume of 110 liter is
simulated and it has been divided into 410,000 tetrahedral control
cells for performing the calculations. The grids at the vicinity of the
nozzle and suction pare are finer to get more accurate results. The
experimental results showed that in a vertical jet, the lowest mixing
time takes place at 35 degree. In addition, mixing time decreased by
increasing the Reynolds number. Furthermore, the CFD simulation
predicted the items as well a flow patterns precisely that validates the
experiments.
Abstract: In this paper, the effect of addition the dune sand powder (DSP) on development of compressive strength and hydration of cement pastes was investigated as a function of water/binder ratio, was varied, on the one hand, the percentage of DSP and on the other, the fineness of DSP. In order to understand better the pozzolanic effect of dune sand powder in cement pastes, we followed the mixtures hydration (50% Pure Lime + 50% DSP) by X-ray diffraction. These mixtures the pastes present a hydraulic setting which is due to the formation of a C-S-H phase (calcium silicate hydrate). The latter is semi-crystallized. This study is a simplified approach to that of the mixtures (80% ordinary Portland cement + 20% DSP), in which the main reaction is the fixing of the lime coming from the cement hydration in the presence of DSP, to form calcium silicate hydrate semi-crystallized of second generation. The results proved that up to (20% DSP) as Portland cement replacement could be used with a fineness of 4000 cm²/g without affecting adversely the compressive strength. After 28 days, the compressive strength at 5, 10 and 15% DSP is superior to Portland cement, with an optimum effect for a percentage of the order of 5% to 10% irrespective of the w/b ratio and fineness of DSP.
Abstract: Thermodynamics characterization Sesame oil
extraction by Acetone, Hexane and Benzene has been evaluated. The
120 hours experimental Data were described by a simple
mathematical model. According to the simulation results and the
essential criteria, Acetone is superior to other solvents but under
certain conditions where oil extraction takes place Hexane is superior
catalyst.