Abstract: The soil profile at site of the bridge project includes soft fine grained soil layer located between 5.0 m to 11.0 m in depth, it has high water content, low SPT no., and low bearing capacity. The clay layer induces high settlement due to surcharge application of earth embankment at ramp T1, ramp T2, and ramp T3 especially at heights from 9m right 3m. Calculated settlement for embankment heights less than 3m may be accepted regarding Saudi Code for soil and foundation. The soil and groundwater at the project site comprise high contents of sulfates and chlorides of high aggressively on concrete and steel bars, respectively. Regarding results of the study, it has been recommended to use stone column piles or new technology named PCC piles as soil improvement to improve the bearing capacity of the weak layer. The new technology is cast in-situ thin wall concrete pipe piles (PCC piles), it has economically advantageous and high workability. The technology can save time of implementation and cost of application is almost 30% of other types of piles.
Abstract: Healthcare waste management continues to present an
array of challenges for developing countries, and Liberia is of no
exception. There is insufficient information available regarding the
generation, handling, and disposal of health care waste. This face
serves as an impediment to healthcare management schemes. The
specific objective of this study is to present an evaluation of the
current health care management practices in Liberia. It also presented
procedures, techniques used, methods of handling, transportation, and
disposal methods of wastes as well as the quantity and composition
of health care waste. This study was conducted as an investigative
case study, covering three different health care facilities; a hospital, a
health center, and a clinic in Monrovia, Montserrado County. The
average waste generation was found to be 0-7kg per day at the clinic
and health center and 8-15kg per/day at the hospital. The composition
of the waste includes hazardous and non-hazardous waste i.e. plastic,
papers, sharps, and pathological elements etc. Nevertheless, the
investigation showed that the healthcare waste generated by the
surveyed healthcare facilities were not properly handled because of
insufficient guidelines for separate collection, and classification, and
adequate methods for storage and proper disposal of generated
wastes. This therefore indicates that there is a need for improvement
within the healthcare waste management system to improve the
existing situation.
Abstract: Copreneurship is a term used to describe the business
pattern of operations run by married couples who share commitment,
goals, and responsibilities in handling a business. Research conducted
overseas showed that copreneurship business activities grew quickly
and played a role in elevating families’ and nations’ socio-economic
standards. In Malaysia, copreneurship has long been cultivated by
spouses. Thus, this study aimed to explore the factors that motivate
married partners to start a copreneurship business, and who is the
dominant partner in the management of this business. The study
participants are four entrepreneurial couples who are SME business
operators selected through purposive sampling. In-depth interviews
and direct observation were used as methods of measurement for
triangulation of qualitative data in this study. The findings of the
interviews were administered using NVivo 8.0 software. The result
shows that freedom is a key factor that drives entrepreneurs to set up
copreneurship businesses, and that the husband dominates the
management aspects of the business. The study gives an overview of
the parties involved in entrepreneurship to provide understanding of
the copreneurship concept as it is practiced. This study provides
academic value by creating understanding of the importance of a
harmonious family institution specifically for forming entrepreneurs
in the familial environment in Malaysia.
Abstract: Despite the benefits of innovation diffusion in the
South African public service, implementation thereof seems to be
problematic, particularly with regard to e-governance which would
enhance the quality of service delivery, especially accessibility,
choice, and mode of operation. This paper reports on differences
between the public service and the private sector in terms of
innovation diffusion. Innovation diffusion will be investigated to
explore identified obstacles that are hindering successful
implementation of e-governance. The research inquiry is underpinned
by the diffusion of innovation theory, which is premised on the
assumption that innovation has a distinct channel, time, and mode of
adoption within the organisation. A comparative thematic document
analysis was conducted to investigate organisational differences with
regard to innovation diffusion. A similar approach has been followed
in other countries, where the same conceptual framework has been
used to guide document analysis in studies in both the private and the
public sectors. As per the recommended conceptual framework, three
organisational characteristics were emphasised, namely the external
characteristics of the organisation, the organisational structure, and
the inherent characteristics of the leadership. The results indicated
that the main difference in the external characteristics lies in the
focus and the clientele of the private sector. With regard to
organisational structure, private organisations have veto power,
which is not the case in the public service. Regarding leadership,
similarities were observed in social and environmental responsibility
and employees’ attitudes towards immediate supervision. Differences
identified included risk taking, the adequacy of leadership
development, organisational approaches to motivation and
involvement in decision making, and leadership style. Due to the
organisational differences observed, it is recommended that
differentiated strategies be employed to ensure effective innovation
diffusion, and ultimately e-governance. It is recommended that the
results of this research be used to stimulate discussion on ways to
improve collaboration between the mentioned sectors, to capitalise on
the benefits of each sector.
Abstract: The importance of culture and tourism in the attractiveness and competitiveness of the countries is central, and many regions are evidencing their cultural assets, tangible and intangible, as a means to create comparative advantages in tourism and produce a distinctive place in response to the pressures of globalization. Culture and tourism are interlinked because of their obvious combination and growth potential. Cultural tourism is a crucial global tourism market with fast growing. Regions can develop significant relations between culture and tourism to increase their attractiveness as places to visit, live and invest, increasing their competitiveness. Accordingly, having new and creative approach to historical areas as cultural value-based destinations can improve their conditions to promote tourism. Furthermore, in 21st century, media become the most important factor affecting the development of urban cities, including public places. As a result of the digital revolution, re-imaging and re-linkage public places by media are essential to create more interactions between public spaces and users, interaction media display, and urban screens, one of the most important defined media. This interaction can transform the urban space from being neglected to be more interactive space with users, especially the pedestrians. The paper focuses on The Walled City of Famagusta. As many other historic quarters elsewhere in the world, is in a process, of decay and deterioration, and its functionally distinctive areas are severely threatened by physical, functional, locational, and image obsolescence at varying degrees. So the focus on the future development of this area through tourism promotion can be an appropriate decision for the monument enhancement of the spatial quality in Walled City of Famagusta. In this paper, it is aimed to identify the effects of these new digital factors to transform public spaces especially in historic urban areas to promote creative tourism. Accordingly, two different analysis methods are used as well as a theoretical review. The first is case study on site and the second is Close ended questionnaire, test many concepts raised in this paper. The physical analysis on site carried out in order to evaluate the walled city restoration for touristic purpose. Besides, theoretical review is done in order to provide background to the subject and cleared Factors to attract tourists.
Abstract: Hydrologic models are increasingly used as tools to
predict stormwater quantity and quality from urban catchments.
However, due to a range of practical issues, most models produce
gross errors in simulating complex hydraulic and hydrologic systems.
Difficulty in finding a robust approach for model calibration is one of
the main issues. Though automatic calibration techniques are
available, they are rarely used in common commercial hydraulic and
hydrologic modelling software e.g. MIKE URBAN. This is partly
due to the need for a large number of parameters and large datasets in
the calibration process. To overcome this practical issue, a
framework for automatic calibration of a hydrologic model was
developed in R platform and presented in this paper. The model was
developed based on the time-area conceptualization. Four calibration
parameters, including initial loss, reduction factor, time of
concentration and time-lag were considered as the primary set of
parameters. Using these parameters, automatic calibration was
performed using Approximate Bayesian Computation (ABC). ABC is
a simulation-based technique for performing Bayesian inference
when the likelihood is intractable or computationally expensive to
compute. To test the performance and usefulness, the technique was
used to simulate three small catchments in Gold Coast. For
comparison, simulation outcomes from the same three catchments
using commercial modelling software, MIKE URBAN were used.
The graphical comparison shows strong agreement of MIKE URBAN
result within the upper and lower 95% credible intervals of posterior
predictions as obtained via ABC. Statistical validation for posterior
predictions of runoff result using coefficient of determination (CD),
root mean square error (RMSE) and maximum error (ME) was found
reasonable for three study catchments. The main benefit of using
ABC over MIKE URBAN is that ABC provides a posterior
distribution for runoff flow prediction, and therefore associated
uncertainty in predictions can be obtained. In contrast, MIKE
URBAN just provides a point estimate. Based on the results of the
analysis, it appears as though ABC the developed framework
performs well for automatic calibration.
Abstract: An experiment to verify the relationships between
physiological indexes of an e-learner and the presence or absence of an
operation during e-learning is described. Electroencephalogram
(EEG), hemoencephalography (HEG), skin conductance (SC), and
blood volume pulse (BVP) values were measured while participants
performed experimental learning tasks. The results show that there are
significant differences between the SC values when reading with
clicking on learning materials and the SC values when reading without
clicking, and between the HEG ratio when reading (with and without
clicking) and the HEG ratio when resting for four of five participants.
We conclude that the SC signals can be used to estimate whether or not
a learner is performing an active task and that the HEG ratios can be
used to estimate whether a learner is learning.
Abstract: Electric field is an important fundamental concept in
electrostatics. In high-school, generally Thai students have already
learned about definition of electric field, electric field due to a point
charge, and superposition of electric fields due to multiple-point
charges. Those are the prerequisite basic knowledge students holding
before entrancing universities. In the first-year university level,
students will be quickly revised those basic knowledge and will be
then introduced to a more complicated topic—electric field due to
continuous charged distributions. We initially found that our
freshman students, who were from the Faculty of Science and
enrolled in the introductory physic course (SCPY 158), often
seriously struggled with the basic physics concepts—superposition of
electric fields and inverse square law and mathematics being relevant
to this topic. These also then resulted on students’ understanding of
advanced topics within the course such as Gauss's law, electric
potential difference, and capacitance. Therefore, it is very important
to determine students' understanding of electric field due to
continuous charged distributions. The open-ended question about
sketching net electric field vectors from a uniformly charged
insulating rod was administered to 260 freshman science students as
pre- and post-tests. All of their responses were analyzed and
classified into five levels of understandings. To get deep
understanding of each level, 30 students were interviewed toward
their individual responses. The pre-test result found was that about
90% of students had incorrect understanding. Even after completing
the lectures, there were only 26.5% of them could provide correct
responses. Up to 50% had confusions and irrelevant ideas. The result
implies that teaching methods in Thai high schools may be
problematic. In addition for our benefit, these students’ alternative
conceptions identified could be used as a guideline for developing the
instructional method currently used in the course especially for
teaching electrostatics.
Abstract: In order to understand whether there is a better than the
learning function of learning methods and improve the CAD Courses
for enterprise’s design human resource development, this research is
applied in learning practical learning computer graphics software. In
this study, Revit building information model for learning content,
design of two different modes of learning curriculum to learning,
learning functions, respectively, and project learning. Via a post-test,
questionnaires and student interviews, etc., to study the effectiveness
of a comparative analysis of two different modes of learning. Students
participate in a period of three weeks after a total of nine-hour course,
and finally written and hands-on test. In addition, fill in the
questionnaire response by the student learning, a total of fifteen
questionnaire title, problem type into the base operating software,
application software and software-based concept features three
directions. In addition to the questionnaire, and participants were
invited to two different learning methods to conduct interviews to
learn more about learning students the idea of two different modes.
The study found that the ad hoc short-term courses in learning, better
learning outcomes. On the other hand, functional style for the whole
course students are more satisfied, and the ad hoc style student is
difficult to accept the ad hoc style of learning.
Abstract: In this paper, an attempt has been made to analyze the effect of wall window orientation on Daylight Illuminance Ratio (DIR) and energy saving in a building known as “SODHA BERS COMPLEX (SBC)” at Varanasi, UP, India. The building has been designed incorporating all passive concepts for thermal comfort as well daylighting concepts to maximize the use of natural daylighting for the occupants in the day to day activities. The annual average DIR and the energy saving has been estimated by using the DIR model for wall window with different orientations under clear sky condition. It has been found that for south oriented window the energy saving per square meter is more compared to the other orientations due to the higher level of solar insolation for the south window in northern hemisphere whereas energy saving potential is minimum for north oriented wall window. The energy saving potential was 26%, 81% and 51% higher for east, south and west oriented window in comparison to north oriented window. The average annual DIR has same trends of variation as the annual energy saving and it is maximum for south oriented window and minimum for north oriented window.
Abstract: The aim of this article is to identify the measures
companies undertake in order to adapt to the environment as well as
discussing their diversity and effectiveness. The research methods
used in the study include an in-depth analysis of the literature and a
case study, which helps to illustrate the issue in question. Referring to
the concept of agility, which is firmly embedded in the theory of
strategic management and has been developed with the aim of
adapting to the environment and its changes, the paper first examines
different types of adaptation measures for companies. Then the issue
under discussion is illustrated with the example of the company
Hortimex. This company is an eminent representative of the world’s
leading manufacturers of food additives and ingredients. The
company was established in 1988 and is a family business, which in
practice means that it conducts business in a responsible manner,
observing the law and respecting the interests of society and the
environment. The company’s mission is to develop a market in
Poland for the products and solutions offered by their partners and to
share their knowledge of additives in food production and
consumption.
Abstract: In this paper, a desiccant solar unit for air
conditioning and desalination is presented first. Secondly, a dynamic
modelling study of the desiccant wheel is developed. After that, a
simulation study and an experimental investigation of the behaviour
of desiccant wheel are developed. The experimental investigation is
done in the chamber of commerce in Freiburg-Germany. Indeed, the
variations of calculated and measured temperatures and specific
humidity of dehumidified and rejected air are presented where a good
agreement is found when comparing the model predictions with
experimental data under the considered range of operating conditions.
Finally, the study of the compartments of desalination and water
condensation shows that the unit can produce an acceptable quantity
of water at the same time of the air conditioning operation.
Abstract: This research provides a technical account of
estimating Transition Probability using Time-homogeneous Markov
Jump Process applying by South African HIV/AIDS data from the
Statistics South Africa. It employs Maximum Likelihood Estimator
(MLE) model to explore the possible influence of Transition
Probability of mortality cases in which case the data was based on
actual Statistics South Africa. This was conducted via an integrated
demographic and epidemiological model of South African HIV/AIDS
epidemic. The model was fitted to age-specific HIV prevalence data
and recorded death data using MLE model. Though the previous
model results suggest HIV in South Africa has declined and AIDS
mortality rates have declined since 2002 – 2013, in contrast, our
results differ evidently with the generally accepted HIV models
(Spectrum/EPP and ASSA2008) in South Africa. However, there is
the need for supplementary research to be conducted to enhance the
demographic parameters in the model and as well apply it to each of
the nine (9) provinces of South Africa.
Abstract: In military aviation, the use of flight simulators has proliferated recently in order to train fifth generation fighter pilots. With these simulators, pilots can carry out real-time flights resulting in seeing their faults and can perform emergency drills prior to real flights. Since we cannot risk losing the aircraft and the pilot himself/herself in the flight training process, flight simulators are of great importance to adapt the fighter pilots competently to real flights aboard the fifth generation aircraft. The real flights are impossible to simulate thoroughly on the ground. To some extent, the fixed-based simulators may assist the pilot to steer aircraft technically and visually but flight simulators can’t trick the pilot’s vestibular, sensory, and perceptual systems without motion platforms. This paper discusses the benefits of motion simulators for fifth generation fighter pilots’ training in preference to the fixed-based counterparts by analyzing their pros and cons.
Abstract: Solar water heating is a thermodynamic process of
heating water using sunlight with the help of solar water heater. Thus,
solar water heater is a device used to harness solar energy. In this
paper, a modified solar water heating system (MSWHS) has been
proposed over flat plate collector (FPC) and Evacuated tube collector
(ETC). The modifications include selection of materials other than
glass, and glass wool which are conventionally used for fabricating
FPC and ETC. Some modifications in design have also been
proposed. Its collector is made of double layer of semi-cylindrical
acrylic tubes and fibre reinforced plastic (FRP) insulation base. Water
tank is made of double layer of acrylic sheet except base and north
wall. FRP is used in base and north wall of the water tank. A concept
of equivalent thickness has been utilised for calculating the
dimensions of collector plate, acrylic tube and tank. A thermal model for the proposed design of MSWHS is developed
and simulation is carried out on MATLAB for the capacity of 200L
MSWHS having collector area of 1.6 m2, length of acrylic tubes of
2m at an inclination angle 25° which is taken nearly equal to the
latitude of the given location. Latitude of Allahabad is 24.45° N. The
results show that the maximum temperature of water in tank and tube
has been found to be 71.2°C and 73.3°C at 17:00hr and 16:00hr
respectively in March for the climatic data of Allahabad. Theoretical performance analysis has been carried out by varying
number of tubes of collector, the tank capacity and climatic data for
given months of winter and summer.
Abstract: HMS Industrial Networks AB has been recognized as
one of the most innovative companies in the industrial
communication industry worldwide. The creation of their Anybus
innovation during the 1990s contributed considerably to the
company’s success. From inception, HMS’ employees were
innovating for the purpose of creating new business (the creation
phase). After the Anybus innovation, they began the process of
internationalization (the commercialization phase), which in turn led
them to concentrate on cost reduction, product quality, delivery
precision, operational efficiency, and increasing growth (the growth
phase). As a result of this transformation, performing new radical
innovations have become more complicated. The purpose of our research was to explore the dynamics of
innovation at HMS from the aspect of key actors, activities, and
events, over the three phases, in order to understand what led to the
creation of their Anybus innovation, and why it has become
increasingly challenging for HMS to create new radical innovations
for the future. Our research methodology was based on a longitudinal,
retrospective study from the inception of HMS in 1988 to 2014, a
single case study inspired by the grounded theory approach. We
conducted 47 interviews and collected 1 024 historical documents for
our research. Our analysis has revealed that HMS’ success in creating the
Anybus, and developing a successful business around the innovation,
was based on three main capabilities – cultivating customer relations
on different managerial and organizational levels, inspiring business
relations, and balancing complementary human assets for the purpose
of business creation. The success of HMS has turned the management’s attention away
from past activities of key actors, of their behavior, and how they
influenced and stimulated the creation of radical innovations.
Nowadays, they are rhetorically focusing on creativity and
innovation. All the while, their real actions put emphasis on growth,
cost reduction, product quality, delivery precision, operational
efficiency, and moneymaking. In the process of becoming an
international company, HMS gradually refocused. In so doing they
became profitable and successful, but they also forgot what made
them innovative in the first place. Fortunately, HMS’ management
has come to realize that this is the case and they are now in search of
recapturing innovation once again. Our analysis indicates that HMS’ management is facing several
barriers to innovation related path dependency and other lock-in
phenomena. HMS’ management has been captured, trapped in their
mindset and actions, by the success of the past. But now their future has to be secured, and they have come to realize that moneymaking is
not everything. In recent years, HMS’ management have begun to
search for innovation once more, in order to recapture their past
capabilities for creating radical innovations. In order to unlock their
managerial perceptions of customer needs and their counter-innovation
driven activities and events, to utilize the full potential of
their employees and capture the innovation opportunity for the future.
Abstract: The cumulative costs for O&M may represent as
much as 65%-90% of the turbine's investment cost. Nowadays the
cost effectiveness concept becomes a decision-making and
technology evaluation metric. The cost of energy metric accounts for
the effect replacement cost and unscheduled maintenance cost
parameters. One key of the proposed approach is the idea of
maintaining the WTs which can be captured via use of a finite state
Markov chain. Such a model can be embedded within a probabilistic
operation and maintenance simulation reflecting the action to be
done. In this paper, an approach of estimating the cost of O&M is
presented. The finite state Markov model is used for decision
problems with number of determined periods (life cycle) to predict
the cost according to various options of maintenance.
Abstract: Recent progress in the next generation of automobile
technology is geared towards incorporating information technology
into cars. Collectively called smart cars are bringing intelligence to
cars that provides comfort, convenience and safety. A branch of smart
cars is connected-car system. The key concept in connected-cars is the
sharing of driving information among cars through decentralized
manner enabling collective intelligence. This paper proposes a
foundation of the information model that is necessary to define the
driving information for smart-cars. Road conditions are modeled
through a unique data structure that unambiguously represent the time
variant traffics in the streets. Additionally, the modeled data structure
is exemplified in a navigational scenario and usage using UML.
Optimal driving route searching is also discussed using the proposed
data structure in a dynamically changing road conditions.
Abstract: Nowadays, food safety is a great public concern;
therefore, robust and effective techniques are required for detecting
the safety situation of goods. Hyperspectral Imaging (HSI) is an
attractive material for researchers to inspect food quality and safety
estimation such as meat quality assessment, automated poultry
carcass inspection, quality evaluation of fish, bruise detection of
apples, quality analysis and grading of citrus fruits, bruise detection
of strawberry, visualization of sugar distribution of melons,
measuring ripening of tomatoes, defect detection of pickling
cucumber, and classification of wheat kernels. HSI can be used to
concurrently collect large amounts of spatial and spectral data on the
objects being observed. This technique yields with exceptional
detection skills, which otherwise cannot be achieved with either
imaging or spectroscopy alone. This paper presents a nonlinear
technique based on kernel Fukunaga-Koontz transform (KFKT) for
detection of fat content in ground meat using HSI. The KFKT which
is the nonlinear version of FKT is one of the most effective
techniques for solving problems involving two-pattern nature. The
conventional FKT method has been improved with kernel machines
for increasing the nonlinear discrimination ability and capturing
higher order of statistics of data. The proposed approach in this paper
aims to segment the fat content of the ground meat by regarding the
fat as target class which is tried to be separated from the remaining
classes (as clutter). We have applied the KFKT on visible and nearinfrared
(VNIR) hyperspectral images of ground meat to determine
fat percentage. The experimental studies indicate that the proposed
technique produces high detection performance for fat ratio in ground
meat.
Abstract: The rising demand for format-flexible packaging
machines is caused by current market changes. Increasing the formatflexibility
is a new goal for the packaging machine manufacturers’
product development process. There are no methodical or designorientated
tools for a comprehensive consideration of this target. This
paper defines the term format-flexibility in the context of packaging
machines and shows the state-of-the-art for improving the
changeover of production machines. The requirements for a new
approach and the concept itself will be introduced, and the method
elements will be explained. Finally, the use of the concept and the
result of the development of a format-flexible packaging machine
will be shown.