Abstract: This research proposes the change of damping coefficient regarding minimum displacement. From the mass with external forced and damper problem, when is the constant external forced transmitted to the understructure in the difference angle between 30 and 60 degrees. This force generates the vibration as general known; however, the objective of this problem is to have minimum displacement. As the angle is changed and the goal is the same; therefore, the damper of the system must be varied while keeping constant spring stiffness. The problem is solved by using nonlinear programming and the suitable changing of the damping coefficient is provided.
Abstract: Geosynthetics have proved to be suitable for
reinforced soil retaining walls. Based on the increasing uses of
geosynthetic reinforced soil systems in the regions, which bear
frequent earthquakes, the study of dynamic behavior of structures
seems necessary. Determining the reinforcement forces is; therefore,
one of the most important and main points of discussions in
designing retaining walls, by which we prevent from conservative
planning. Thus, this paper intended to investigate the effects of such
parameters as wall height, acceleration type, vertical spacing of
reinforcement, type of reinforcement and soil type on forces and
deformation through numerical modeling of the geosynthetic
reinforced soil retaining walls (GRSRW) under dynamic loading with
finite difference method by using FLAC. The findings indicate rather
positive results with each parameter.
Abstract: A two-dimensional thin-walled capsule of a flexible
semi-permeable membrane is adhered onto a rigid planar substrate
under adhesive forces (derived from a potential function) in the
presence of osmosis across the membrane. The capsule is immersed
in a hypotonic and diluted binary solution of a non-electrolyte
solute. The Stokes flow problem is solved by the immersed interface
method (IIM) with equal viscosities for the enclosed and
surrounding fluid of the capsule. The numerical results obtained are
verified against two simplified theoretical solutions and the
agreements are good. The osmotic inflation of the adhered capsule is
studied as a function of the solute concentration field, hydraulic
conductivity, and the initial capsule shape. Our findings indicate that
the contact length shrinks in dimension as capsule inflates in the
hypotonic medium, and the equilibrium contact length does not
depend on the hydraulic conductivity of the membrane and the
initial shape of the capsule.
Abstract: It has been shown that a load discontinuity at the end of
an impulse will result in an extra impulse and hence an extra amplitude
distortion if a step-by-step integration method is employed to yield the
shock response. In order to overcome this difficulty, three remedies
are proposed to reduce the extra amplitude distortion. The first remedy
is to solve the momentum equation of motion instead of the force
equation of motion in the step-by-step solution of the shock response,
where an external momentum is used in the solution of the momentum
equation of motion. Since the external momentum is a resultant of the
time integration of external force, the problem of load discontinuity
will automatically disappear. The second remedy is to perform a single
small time step immediately upon termination of the applied impulse
while the other time steps can still be conducted by using the time step
determined from general considerations. This is because that the extra
impulse caused by a load discontinuity at the end of an impulse is
almost linearly proportional to the step size. Finally, the third remedy
is to use the average value of the two different values at the integration
point of the load discontinuity to replace the use of one of them for
loading input. The basic motivation of this remedy originates from the
concept of no loading input error associated with the integration point
of load discontinuity. The feasibility of the three remedies are
analytically explained and numerically illustrated.
Abstract: This study employs auto-regressive distributed lag (ARDL) bounds approach to cointegration for long run and errorcorrection modeling (ECM) for short run analysis to examine the relationship between revenue gap and economic growth for Pakistan using annual time series data over the period 1980 to 2008. The short and long run results indicate that revenue gap is statistical significant and negatively effect economic growth. The significant and negative coefficient of error correction term in ECM indicates that after a shock, the long rum equilibrium will again converge towards equilibrium about 10.406 percent within a year.
Abstract: Carbon Capture & Storage (CCS) is one of the various
methods that can be used to reduce the carbon footprint of the
energy sector. This paper focuses on the absorption of CO2 from
flue gas using packed columns, whose efficiency is highly dependent
on the structure of the liquid films within the column. To study the
characteristics of liquid films a CFD solver, OpenFOAM is utilised
to solve two-phase, isothermal film flow using the volume-of-fluid
(VOF) method. The model was validated using existing experimental
data and the Nusselt theory. It was found that smaller plate inclination
angles, with respect to the horizontal plane, resulted in larger wetted
areas on smooth plates. However, only a slight improvement in
the wetted area was observed. Simulations were also performed
using a ridged plate and it was observed that these surface textures
significantly increase the wetted area of the plate. This was mainly
attributed to the channelling effect of the ridges, which helped to
oppose the surface tension forces trying to minimise the surface area.
Rivulet formations on the ridged plate were also flattened out and
spread across a larger proportion of the plate width.
Abstract: Transient eddy current problem is solved in the
present paper by the method of the Laplace transform for the case of
a double conductor line located parallel to a conducting half-space.
The Fourier sine and cosine integral transforms are used in order to
find the Laplace transform of the solution. The inverse Laplace
transform of the solution is found in closed form. The integrated
electromotive force per unit length of the double conductor line is
calculated in the form of an improper integral.
Abstract: Extraction of Fe(III) from aqueous solution using Trin-
butyl Phosphate (TBP) as carrier needs a highly acidic medium
(>6N) as it favours formation of chelating complex FeCl3.TBP.
Similarly, stripping of Iron(III) from loaded organic solvents requires
neutral pH or alkaline medium to dissociate the same complex. It is
observed that TBP co-extracts acids along with metal, which causes
reversal of driving force of extraction and iron(III) is re-extracted
back from the strip phase into the feed phase during Liquid Emulsion
Membrane (LEM) pertraction. Therefore, rate of extraction of
different mineral acids (HCl, HNO3, H2SO4) using TBP with and
without presence of metal Fe(III) was examined. It is revealed that in
presence of metal acid extraction is enhanced. Determination of mass
transfer coefficient of both acid and metal extraction was performed
by using Bulk Liquid Membrane (BLM). The average mass transfer
coefficient was obtained by fitting the derived model equation with
experimentally obtained data. The mass transfer coefficient of the
mineral acid extraction is in the order of kHNO3 = 3.3x10-6m/s > kHCl =
6.05x10-7m/s > kH2SO4 = 1.85x10-7m/s. The distribution equilibria of
the above mentioned acids between aqueous feed solution and a
solution of tri-n-butyl-phosphate (TBP) in organic solvents have been
investigated. The stoichiometry of acid extraction reveals the
formation of TBP.2HCl, HNO3.2TBP, and TBP.H2SO4 complexes.
Moreover, extraction of Iron(III) by TBP in HCl aqueous solution
forms complex FeCl3.TBP.2HCl while in HNO3 medium forms
complex 3FeCl3.TBP.2HNO3
Abstract: Industrial robots become useless without end-effectors
that for many instances are in the form of friction grippers.
Commonly friction grippers apply frictional forces to different
objects on the basis of programmers- experiences. This puts a
limitation on the effectiveness of gripping force that may result in
damaging the object. This paper describes various stages of design
and development of a low cost sensor-based robotic gripper that
would facilitate the task of applying right gripping forces to different
objects. The gripper is also equipped with range sensors in order to
avoid collisions of the gripper with objects. It is a fully functional
automated pick and place gripper which can be used in many
industrial applications. Yet it can also be altered or further developed
in order to suit a larger number of industrial activities. The current
design of gripper could lead to designing completely automated robot
grippers able to improve the efficiency and productivity of industrial
robots.
Abstract: This paper presents a narrative management system
for organizations to capture organization's tacit knowledge
through stories. The intention of capturing tacit knowledge is to
address the problem that comes with the mobility of workforce in
organisation. Storytelling in knowledge management context is
seen as a powerful management tool to communicate tacit
knowledge in organization. This narrative management system is
developed firstly to enable uploading of many types of knowledge
sharing stories, from general to work related-specific stories and
secondly, each video has comment functionality where knowledge
users can post comments to other knowledge users. The narrative
management system allows the stories to browse, search and view
by the users. In the system, stories are stored in a video repository.
Stories that were produced from this framework will improve
learning, knowledge transfer facilitation and tacit knowledge
quality in an organization.
Abstract: The paper investigates downtrend algorithm and
trading strategy based on chart pattern recognition and technical
analysis in futures market. The proposed chart formation is a pattern
with the lowest low in the middle and one higher low on each side.
The contribution of this paper lies in the reinforcement of statements
about the profitability of momentum trend trading strategies.
Practical benefit of the research is a trading algorithm in falling
markets and back-test analysis in futures markets. When based on
daily data, the algorithm has generated positive results, especially
when the market had downtrend period. Downtrend algorithm can be
applied as a hedge strategy against possible sudden market crashes.
The proposed strategy can be interesting for futures traders, hedge
funds or scientific researchers performing technical or algorithmic
market analysis based on momentum trend trading.
Abstract: Lateral expansion is a factor defining the level of
confinement in reinforced concrete columns. Therefore, predicting
the lateral strain relationship with axial strain becomes an important
issue. Measuring lateral strains in experiments is difficult and only
few report experimental lateral strains. Among the existing analytical
formulations, two recent models are compared with available test
results in this paper with shortcomings highlighted. A new analytical
model is proposed here for lateral strain axial strain relationship and
is based on the supposition that the concrete behaves linear elastic in
the early stages of loading and then nonlinear hardening up to the
peak stress and then volumetric expansion. The proposal for the
lateral strain axial strain relationship after the peak stress is mainly
based on the hypothesis that the plastic lateral strain varies linearly
with the plastic axial strain and it is shown that this is related to the
lateral confinement level.
Abstract: The chatter is one of the major limitations of the productivity in the ball end milling process. It affects the surface roughness, the dimensional accuracy and the tool life. The aim of this research is to propose the new system to detect the chatter during the ball end milling process by using the wavelet transform. The proposed method is implemented on the 5-axis CNC machining center and the new three parameters are introduced from three dynamic cutting forces, which are calculated by taking the ratio of the average variances of dynamic cutting forces to the absolute variances of themselves. It had been proved that the chatter can be easier to detect during the in-process cutting by using the new parameters which are proposed in this research. The experimentally obtained results showed that the wavelet transform can provide the reliable results to detect the chatter under various cutting conditions.
Abstract: The electrical interaction between two axisymmetric
spheroidal particles in an electrolyte solution is examined numerically.
A Galerkin finite element method combined with a Newton-Raphson
iteration scheme is proposed to evaluate the spatial variation in the
electrical potential, and the result obtained used to estimate the
interaction energy between two particles. We show that if the surface
charge density is fixed, the potential gradient is larger at a point, which
has a larger curvature, and if surface potential is fixed, surface charge
density is proportional to the curvature. Also, if the total interaction
energy against closest surface-to-surface curve exhibits a primary
maximum, the maximum follows the order (oblate-oblate) >
(sphere-sphere)>(oblate-prolate)>(prolate-prolate), and if the curve
has a secondary minimum, the absolute value of the minimum follows
the same order.
Abstract: Functional gastrointestinal disorders affect millions of people spread all age regardless of race and sex. There are, however, rare diagnostic methods for the functional gastrointestinal disorders because functional disorders show no evidence of organic and physical causes. Our research group identified recently that the gastrointestinal tract well in the patients with the functional gastrointestinal disorders becomes more rigid than healthy people when palpating the abdominal regions overlaying the gastrointestinal tract. Aim of this study is, therefore, to develop a diagnostic system for the functional gastrointestinal disorders based on ultrasound technique, which can quantify the characteristic above related to the rigidity of the gastrointestinal tract well. Ultrasound system was designed. The system consisted of transmitter, ultrasonic transducer, receiver, TGC, and CPLD, and verified via a phantom test. For the phantom test, ten soft-tissue specimens were harvested from porcine. Five of them were then treated chemically to mimic a rigid condition of gastrointestinal tract well, which was induced by functional gastrointestinal disorders. Additionally, the specimens were tested mechanically to identify if the mimic was reasonable. The customized ultrasound system was finally verified through application to human subjects with/without functional gastrointestinal disorders (Normal and Patient Groups). It was identified from the mechanical test that the chemically treated specimens were more rigid than normal specimen. This finding was favorably compared with the result obtained from the phantom test. The phantom test also showed that ultrasound system well described the specimen geometric characteristics and detected an alteration in the specimens. The maximum amplitude of the ultrasonic reflective signal in the rigid specimens (0.2±0.1Vp-p) at the interface between the fat and muscle layers was explicitly higher than that in the normal specimens (0.1±0.0Vp-p). Clinical tests using our customized ultrasound system for human subject showed that the maximum amplitudes of the ultrasonic reflective signals near to the gastrointestinal tract well for the patient group (2.6±0.3Vp-p) were generally higher than those in normal group (0.1±0.2Vp-p). Here, maximum reflective signals was appeared at 20mm depth approximately from abdominal skin for all human subjects, corresponding to the location of the boundary layer close to gastrointestinal tract well. These results suggest that newly designed diagnostic system based on ultrasound technique may diagnose enough the functional gastrointestinal disorders.
Abstract: Phase transformation temperature is one of the most important parameters for the shape memory alloys (SMAs). The most popular method to determine these phase transformation temperatures is the Differential Scanning Calorimeter (DSC), but due to the limitation of the DSC testing itself, it made it difficult for the finished product which is not in the powder form. A novel method which uses the Universal Testing Machine has been conducted to determine the phase transformation temperatures. The Flexinol wire was applied with force and maintained throughout the experiment and at the same time it was heated up slowly until a temperature of approximately 1000C with direct current. The direct current was then slowly decreased to cool down the temperature of the Flexinol wire. All the phase transformation temperatures for Flexinol wire were obtained. The austenite start at 52.540C and austenite finish at 60.900C, while martensite start at 44.780C and martensite finish at 32.840C.
Abstract: Carbon fibers have specific characteristics in
comparison with industrial and structural materials used in different
applications. Special properties of carbon fibers make them attractive
for reinforcing and fabrication of composites. These fibers have been
utilized for composites of metals, ceramics and plastics. However,
it-s mainly used in different forms to reinforce lightweight polymer
materials such as epoxy resin, polyesters or polyamides. The
composites of carbon fiber are stronger than steel, stiffer than
titanium, and lighter than aluminum and nowadays they are used in a
variety of applications. This study explains applications of carbon
fibers in different fields such as space, aviation, transportation,
medical, construction, energy, sporting goods, electronics, and the
other commercial/industrial applications. The last findings of
composites with polymer, metal and ceramic matrices containing
carbon fibers and their applications in the world investigated.
Researches show that carbon fibers-reinforced composites due to
unique properties (including high specific strength and specific
modulus, low thermal expansion coefficient, high fatigue strength,
and high thermal stability) can be replaced with common industrial
and structural materials.
Abstract: In this study, structural, mechanical, thermal and
electrical properties of poly (lactic acid) (PLA) nanocomposites with
low-loaded (0-1.5 wt%) untreated, heat and nitric acid treated multiwalled
carbon nanotubes (MWCNTs) were studied. Among the
composites, untreated 0.5 wt % MWCNTs and acid-treated 1.0 wt%
MWCNTs reinforced PLA show the tensile strength and modulus
values higher than the others. These two samples along with pure
PLA exhibit the stable orthorhombic α-form, whilst other samples
reveal the less stable orthorhombic β-form, as demonstrated by X-ray
diffraction study. Differential scanning calorimetry reveals the
evolution of the mentioned different phases by controlled cooling and
discloses an enhancement of PLA crystallization by nanotubes
incorporation. Thermogravimetric analysis shows that the MWCNTs
loaded sample degraded faster than PLA. Surface resistivity of the
nanocomposites is found to be dropped drastically by a factor of 1013
with a low loading of MWCNTs (1.5 wt%).
Abstract: Two-dimensional heat conduction within a composed solid material with a constant internal heat generation has been investigated numerically in a sector of the rotor a generator. The heat transfer between two adjacent materials is assumed to be purely conduction. Boundary conditions are assumed to be forced convection on the fluid side and adiabatic on symmetry lines. The control volume method is applied for the diffusion energy equation. Physical coordinates are transformed to the general curvilinear coordinates. Then by using a line-by-line method, the temperature distribution in a sector of the rotor has been determined. Finally, the results are normalized and the effect of cooling fluid on the maximum temperature of insulation is investigated.
Abstract: In this paper, an approach for finding optimized
layouts for connecting PV units delivering maximum array output
power is suggested. The approach is based on considering the
different varying parameters of PV units that might be extracted from
a general two-diode model. These are mainly, solar irradiation,
reverse saturation currents, ideality factors, series and shunt
resistances in addition to operating temperature. The approach has
been tested on 19 possible 2×3 configurations and allowed to
determine the optimized configurations as well as examine the effects
of the different units- parameters on the maximum output power.
Thus, using this approach, standard arrays with n×m units can be
configured for maximum generated power and allows designing PV
based systems having reduced surfaces to fit specific required power,
as it is the case for solar cars and other mobile systems.