Abstract: In this study, the butt welding of the commercial AZ31 magnesium alloy sheets have been carried out by using Tungsten Inert Gas (TIG) welding process with alternative and pulsed current. Welded samples were examined with regards to hardness and microstructure. Despite some recent developments in welding of magnesium alloys, they have some problems such as porosity, hot cracking, oxide formation and so on. Samples of the welded parts have undergone metallographic and mechanical examination. Porosities and homogeneous micron grain oxides were rarely observed. Orientations of the weld microstructure in terms of heat transfer also were rarely observed and equiaxed grain morphology was dominant grain structure as in the base metal. As results, fusion zone and few locations of the HAZ of the welded samples have shown twin’s grains. Hot cracking was not observed for any samples. Weld bead geometry of the welded samples were evaluated as normal according to welding parameters. In the results, conditions of alternative and pulsed current and the samples were compared to each other with regards to microstructure and hardness.
Abstract: While the need for equal access to civil, political as well as economic, social and cultural rights is clear under the international law, the adoption of the Convention on the Elimination of all forms of Discrimination against women in 1979 made this even clearer. Despite this positive progress, the abuse of refugee women's rights is one of the basic underlying root causes of their marginalisation and violence in their countries of asylum. This paper presents a critical review on the development of refugee women's rights at the international levels and national levels. It provides an array of scholarly literature on this issue and examines the measures taken by the international community to curb the problem of violence against women in their various provisions through the instruments set. It is cognizant of the fact that even if conflict affects both refugee women and men, the effects on women refugees are deep-reaching, due to the cultural strongholds they face. An important aspect of this paper is that it is conceptualised against the fact that refugee women face the problem of sexual and gender based first as refugees and second as women, yet, their rights are stumbled upon. Often times they have been rendered "worthless victims" who are only in need of humanitarian assistance than active participants committed to change their plight through their participation in political, economic and social participation in their societies. Scholars have taken notice of the fact that women's rights in refugee settings have been marginalized and call for a need to incorporate their perspectives in the planning and management of refugee settings in which they live. Underpinning this discussion is feminism theory which gives a clear understanding of the root cause of refugee women's problems. Finally, this paper suggests that these policies should be translated into action at local, national international and regional levels to ensure sustainable peace.
Abstract: Water is essential for life and fresh water is a finite
resource that is becoming scarce day by day even though it is
recycled by hydrological cycle. The fresh water reserves are being
polluted due to expanding irrigation, industries, urban population and
its development. Contaminated water leads to several health
problems. With the increasing demand of fresh water, solar
distillation is an alternate solution which uses solar energy to
evaporate water and then to condense it, thereby collecting distilled
water within or outside the same system to use it as potable water.
The structure that houses the process is known as a 'solar still'. In this
paper, ‘Modified double slope solar still (MDSSS)’ & 'Modified
double slope basin type multiwick solar still (MDSBMSS)' have been
designed to convert saline, brackish water into drinking water. In this
work two different modified solar stills are fabricated to study the
performance of these solar stills. For modification of solar stills,
Fibre Reinforced Plastic (FRP) and Acrylic sheets are used. The
experiments in MDSBMSS and MDSSS was carried on 10
September 2015 & 5 November 2015 respectively. Performances of
the stills were investigated. The amount of distillate has been found
3624 Ml/day in MDSBMSS on 10 September 2015 and 2400 Ml/day
in MDSSS on 5 November 2015.
Abstract: In subjective terms, Polish SME sector occupies a
prominent position in the national economic development, in which
planning of the management strategies should be primarily based on
identifying and meeting the innovation needs. As a research sample, there is chosen a printing sector of industry.
SMEs share in printing sector in Poland is estimated at the level of
81% of all enterprises. In recent years, the printing industry achieved
one of the highest levels of EU support in Poland. There is a
relatively high increase in the development of technological
innovations in equipment and the associated significant increase in
production capacity. It can be also noticed that on average, every
third enterprise belonging to the printing industry has implemented
innovations, but not all of them effected in better economic results.
Therefore, the aim of this article is to evaluate the impact of the
implementation of innovation projects financed from the EU funds
for performance of SMEs in the printing industry. As the results of research of EU funds co-financing effects on the
development of innovation in the printing industry, it was specified
that examined SMEs prefer to implement product innovation to
receive a grant to the project at a level between 40% to 60%, the
remaining part of the investment is usually covered with equity. The most common type of innovation had indicated a single
implementation, related only to the change in process, technology, or
organization. The relationship between variables of the EU funds and
management of innovative activities was verified. It has been
observed that the identified variables arising from the support in a
form of the EU funds had a positive effect on the level of earned
revenue, the increase in margin and in increase in employment as
well. It was confirmed that the implemented innovations supported
by the European funds have a positive impact on the performance of
the printing companies. Although there is a risk that due to the
decreasing demand for printing services such a high level of funding
the companies in this sector will significantly increase competition in
the long term, that may also contribute to the economic problems of
the enterprises belonging to the analyzed branch.
Abstract: Since the advent of the law 86/14 concerning the
exploitation of the national territory by foreign companies in
partnership with the Algerian oil and gas company, the problem of
hydrocarbons metering in the sharing production come out.
More generally, good management counting hydrocarbons can
provide data on the production wells, the field and the reservoir for
medium and long term planning, particularly in the context of the
management and field development.
In this work, we are interested in the transactional metering which
is a very delicate and crucial period in the current context of the new
hydrocarbon’s law characterized by assets system between the
various activities of Sonatrach and its foreign partners.
After a state of the art on hydrocarbons metering devices in
Algeria and elsewhere, we will decline the advantages and
disadvantages of each system, and then we describe the problem to
try to reach an optimal solution.
Abstract: Problem of food preservation is extremely important
for mankind. Viscous damage ("illness") of bread results from
development of Bacillus spp. bacteria. High temperature resistant
spores of this microorganism are steady against 120°C) and remain in
bread during pastries, potentially causing spoilage of the final
product. Scientists are interested in further characterization of bread
spoiling Bacillus spp. species. Our aim was to find weather yeast
Saccharomyces cerevisiae strains that are able to produce natural
antimicrobial killer factor can preserve bread illness. By diffusion
method, we showed yeast antagonistic activity against spore-forming
bacteria. Experimental technological parameters were the same as for
bakers' yeasts production on the industrial scale. Risograph test
during dough fermentation demonstrated gas production. The major
finding of the study was a clear indication of the presence of killer
yeast strain antagonistic activity against rope in bread causing
bacteria. After demonstrating antagonistic effect of S. cerevisiae on
bacteria using solid nutrient medium, we tested baked bread under
provocative conditions. We also measured formation of carbon
dioxide in the dough, dough-making duration and quality of the final
products, when using different strains of S. cerevisiae. It is
determined that the use of yeast S. cerevisiae RCAM 01730 killer
strain inhibits appearance of rope in bread. Thus, natural yeast
antimicrobial killer toxin, produced by some S. cerevisiae strains is
an anti-rope in bread protector.
Abstract: Experiments were performed to investigate the effects of roughness on the reattachment and redevelopment regions over a 12 mm forward facing step (FFS) in an open channel flow. The experiments were performed over an upstream smooth wall and a smooth FFS, an upstream wall coated with sandpaper 36 grit and a smooth FFS and an upstream rough wall produced from sandpaper 36 grit and a FFS coated with sandpaper 36 grit. To investigate only the wall roughness effects, Reynolds number, Froude number, aspect ratio and blockage ratio were kept constant. Upstream profiles showed reduced streamwise mean velocities close to the rough wall compared to the smooth wall, but the turbulence level was increased by upstream wall roughness. The reattachment length for the smooth-smooth wall experiment was 1.78h; however, when it is replaced with rough-smooth wall the reattachment length decreased to 1.53h. It was observed that the upstream roughness increased the physical size of contours of maximum turbulence level; however, the downstream roughness decreased both the size and magnitude of contours in the vicinity of the leading edge of the step. Quadrant analysis was performed to investigate the dominant Reynolds shear stress contribution in the recirculation region. The Reynolds shear stress and turbulent kinetic energy profiles after the reattachment showed slower recovery compared to the streamwise mean velocity, however all the profiles fairly collapse on their corresponding upstream profiles at x/h = 60. It was concluded that to obtain a complete collapse several more streamwise distances would be required.
Abstract: Despite the benefits of innovation diffusion in the
South African public service, implementation thereof seems to be
problematic, particularly with regard to e-governance which would
enhance the quality of service delivery, especially accessibility,
choice, and mode of operation. This paper reports on differences
between the public service and the private sector in terms of
innovation diffusion. Innovation diffusion will be investigated to
explore identified obstacles that are hindering successful
implementation of e-governance. The research inquiry is underpinned
by the diffusion of innovation theory, which is premised on the
assumption that innovation has a distinct channel, time, and mode of
adoption within the organisation. A comparative thematic document
analysis was conducted to investigate organisational differences with
regard to innovation diffusion. A similar approach has been followed
in other countries, where the same conceptual framework has been
used to guide document analysis in studies in both the private and the
public sectors. As per the recommended conceptual framework, three
organisational characteristics were emphasised, namely the external
characteristics of the organisation, the organisational structure, and
the inherent characteristics of the leadership. The results indicated
that the main difference in the external characteristics lies in the
focus and the clientele of the private sector. With regard to
organisational structure, private organisations have veto power,
which is not the case in the public service. Regarding leadership,
similarities were observed in social and environmental responsibility
and employees’ attitudes towards immediate supervision. Differences
identified included risk taking, the adequacy of leadership
development, organisational approaches to motivation and
involvement in decision making, and leadership style. Due to the
organisational differences observed, it is recommended that
differentiated strategies be employed to ensure effective innovation
diffusion, and ultimately e-governance. It is recommended that the
results of this research be used to stimulate discussion on ways to
improve collaboration between the mentioned sectors, to capitalise on
the benefits of each sector.
Abstract: The importance of culture and tourism in the attractiveness and competitiveness of the countries is central, and many regions are evidencing their cultural assets, tangible and intangible, as a means to create comparative advantages in tourism and produce a distinctive place in response to the pressures of globalization. Culture and tourism are interlinked because of their obvious combination and growth potential. Cultural tourism is a crucial global tourism market with fast growing. Regions can develop significant relations between culture and tourism to increase their attractiveness as places to visit, live and invest, increasing their competitiveness. Accordingly, having new and creative approach to historical areas as cultural value-based destinations can improve their conditions to promote tourism. Furthermore, in 21st century, media become the most important factor affecting the development of urban cities, including public places. As a result of the digital revolution, re-imaging and re-linkage public places by media are essential to create more interactions between public spaces and users, interaction media display, and urban screens, one of the most important defined media. This interaction can transform the urban space from being neglected to be more interactive space with users, especially the pedestrians. The paper focuses on The Walled City of Famagusta. As many other historic quarters elsewhere in the world, is in a process, of decay and deterioration, and its functionally distinctive areas are severely threatened by physical, functional, locational, and image obsolescence at varying degrees. So the focus on the future development of this area through tourism promotion can be an appropriate decision for the monument enhancement of the spatial quality in Walled City of Famagusta. In this paper, it is aimed to identify the effects of these new digital factors to transform public spaces especially in historic urban areas to promote creative tourism. Accordingly, two different analysis methods are used as well as a theoretical review. The first is case study on site and the second is Close ended questionnaire, test many concepts raised in this paper. The physical analysis on site carried out in order to evaluate the walled city restoration for touristic purpose. Besides, theoretical review is done in order to provide background to the subject and cleared Factors to attract tourists.
Abstract: Hydrologic models are increasingly used as tools to
predict stormwater quantity and quality from urban catchments.
However, due to a range of practical issues, most models produce
gross errors in simulating complex hydraulic and hydrologic systems.
Difficulty in finding a robust approach for model calibration is one of
the main issues. Though automatic calibration techniques are
available, they are rarely used in common commercial hydraulic and
hydrologic modelling software e.g. MIKE URBAN. This is partly
due to the need for a large number of parameters and large datasets in
the calibration process. To overcome this practical issue, a
framework for automatic calibration of a hydrologic model was
developed in R platform and presented in this paper. The model was
developed based on the time-area conceptualization. Four calibration
parameters, including initial loss, reduction factor, time of
concentration and time-lag were considered as the primary set of
parameters. Using these parameters, automatic calibration was
performed using Approximate Bayesian Computation (ABC). ABC is
a simulation-based technique for performing Bayesian inference
when the likelihood is intractable or computationally expensive to
compute. To test the performance and usefulness, the technique was
used to simulate three small catchments in Gold Coast. For
comparison, simulation outcomes from the same three catchments
using commercial modelling software, MIKE URBAN were used.
The graphical comparison shows strong agreement of MIKE URBAN
result within the upper and lower 95% credible intervals of posterior
predictions as obtained via ABC. Statistical validation for posterior
predictions of runoff result using coefficient of determination (CD),
root mean square error (RMSE) and maximum error (ME) was found
reasonable for three study catchments. The main benefit of using
ABC over MIKE URBAN is that ABC provides a posterior
distribution for runoff flow prediction, and therefore associated
uncertainty in predictions can be obtained. In contrast, MIKE
URBAN just provides a point estimate. Based on the results of the
analysis, it appears as though ABC the developed framework
performs well for automatic calibration.
Abstract: In order to understand whether there is a better than the
learning function of learning methods and improve the CAD Courses
for enterprise’s design human resource development, this research is
applied in learning practical learning computer graphics software. In
this study, Revit building information model for learning content,
design of two different modes of learning curriculum to learning,
learning functions, respectively, and project learning. Via a post-test,
questionnaires and student interviews, etc., to study the effectiveness
of a comparative analysis of two different modes of learning. Students
participate in a period of three weeks after a total of nine-hour course,
and finally written and hands-on test. In addition, fill in the
questionnaire response by the student learning, a total of fifteen
questionnaire title, problem type into the base operating software,
application software and software-based concept features three
directions. In addition to the questionnaire, and participants were
invited to two different learning methods to conduct interviews to
learn more about learning students the idea of two different modes.
The study found that the ad hoc short-term courses in learning, better
learning outcomes. On the other hand, functional style for the whole
course students are more satisfied, and the ad hoc style student is
difficult to accept the ad hoc style of learning.
Abstract: Historic paths in today's cities are facing the pressure
of the urban development due to the rapid urban growth. Every new
development is tearing the old urban fabric and the socio-economic
character of the historic paths. Furthermore, in some cases historic
paths suffer from negligence and decay. Kom El Dekka historic path
was one of those deteriorated paths in the city of Alexandria, Egypt,
in spite of its high heritage and socio-economic value. Therefore,
there was a need to develop urban regeneration strategies as a part of
a wider sustainable development vision, to handle the situation and
revitalize the path as a livable space in the heart of the city. This
study aims to develop a comprehensive assessment methodology to
evaluate the different values of the path and to create community-oriented
and economic-based analysis methodology for its socio-economic
values. These analysis and assessments provide strategies
for any regeneration action plan for Kom El Dekka historic path.
Abstract: The rapid growth of the human population and the
environmental degradation associated with increased consumption of
resources raises concerns on sustainability. Social sustainability
constitutes one of the three dimensions of sustainability together with
environmental and economic dimensions. Even though there is not an
agreement on what social sustainability consists of, it is a well known
fact that it necessitates user participation. The fore, this study aims to
observe and analyze the role of user participation on social
sustainability. In this paper, the links between user participation and indicators of
social sustainability have been searched. In order to achieve this, first
of all a literature review on social sustainability has been done;
accordingly, the information obtained from researches has been used
in the evaluation of the projects conducted in the developing
countries considering user participation. These examples are taken as
role models with pros and cons for the development of the checklist
for the evaluation of the case studies. Furthermore, a case study over
the post earthquake residential settlements in Turkey have been
conducted. The case study projects are selected considering different building
scales (differing number of residential units), scale of the problem
(post-earthquake settlements, rehabilitation of shanty dwellings) and
the variety of users (differing socio-economic dimensions). Decisionmaking,
design, building and usage processes of the selected projects
and actors of these processes have been investigated in the context of
social sustainability. The cases include: New Gourna Village by
Hassan Fathy, Quinta Monroy dwelling units conducted in Chile by
Alejandro Aravena and Beyköy and Beriköy projects in Turkey
aiming to solve the problem of housing which have appeared after the
earthquake happened in 1999 have been investigated. Results of the
study possible links between social sustainability indicators and user
participation and links between user participation and the
peculiarities of place. Results are compared and discussed in order to find possible
solutions to form social sustainability through user participation.
Results show that social sustainability issues depend on communities'
characteristics, socio-economic conditions and user profile but user
participation has positive effects on some social sustainability
indicators like user satisfaction, a sense of belonging and social
stability.
Abstract: The aim of this research is to understand how the
emerging power bloc BRICS employs infrastructure development
narratives to construct a new world order. BRICS is an international
body consisting of five emerging countries that collaborate on
economic and political issues: Brazil, Russia, India, China, and South
Africa. This study explores the projection of infrastructure
development narratives through an analysis of BRICS’ attention to
infrastructure investment and financing, its support of the New
Partnership on African Development and the establishment of the
New Development Bank in Shanghai. The theory of Strategic
Narratives is used to explore BRICS’ commitment to infrastructure
development and to distinguish three layers: system narratives
(BRICS as a global actor to propose development reform), identity
narratives (BRICS as a collective identity joining efforts to act upon
development aspirations) and issue narratives (BRICS committed to a
range of issues of which infrastructure development is prominent).
The methodology that is employed is a narrative analysis of BRICS’
official documents, media statements, and website imagery. A
comparison of these narratives illuminates tensions at the three layers
and among the five member states. Identifying tensions among
development infrastructure narratives provides an indication of how
policymaking for infrastructure development could be improved.
Subsequently, it advances BRICS’ ability to act as a global actor to
construct a new world order.
Abstract: Debts reconstruction under some of moratorium
projects is one of important method that highly benefits to both the
Banks and farmers. The method can reduce probabilities for nonprofits
loan. This paper discuss about debts reconstruction and career
development training for farmers in Thailand between 2011 and
2013. The research designed is mix-method between quantitative
survey and qualitative survey. Sample size for quantitative method is
1003 cases. Data gathering procedure is between October and
December 2013. Main results affirmed that debts reconstruction is
needed. And there are numerous benefits from farmers’ career
development training. Many of farmers who attend field school
activities able to bring knowledge learned to apply for the farms’
work. They can reduce production costs. Framers’ quality of life and
their household well-being also improve. This program should apply
in any countries where farmers have highly debts and highly risks for
not return the debts.
Abstract: Ultrasonic metal welding has been the subject of ongoing research and development, most recently concentrating on metal joining in miniature devices, for example to allow solder-free wire bonding. As well as at the small scale, there are also opportunities to research the joining of thicker sheet metals and to widen the range of similar and dissimilar materials that can be successfully joined using this technology. This study presents the design, characterisation and test of a lateral-drive ultrasonic metal spot welding device. The ultrasonic metal spot welding horn is modelled using finite element analysis (FEA) and its vibration behaviour is characterised experimentally to ensure ultrasonic energy is delivered effectively to the weld coupon. The welding stack and fixtures are then designed and mounted on a test machine to allow a series of experiments to be conducted for various welding and ultrasonic parameters. Weld strength is subsequently analysed using tensile-shear tests. The results show how the weld strength is particularly sensitive to the combination of clamping force and ultrasonic vibration amplitude of the welding tip, but there are optimal combinations of these and also limits that must be clearly identified.
Abstract: Centrifugal-casting machine is used in manufacturing
special machine components like multi-layer journal bearing used in
all internal combustion engine, steam, gas turbine and air craft turboengine
where isotropic properties and high precisions are desired.
Moreover, this machine can be used in manufacturing thin wall hightech
machine components like cylinder liners and piston rings of IC
engine and other machine parts like sleeves, and bushes. Heavy-duty
machine component like railway wheel can also be prepared by
centrifugal casting. A lot of technological developments are required
in casting process for production of good casted machine body and
machine parts. Usually defects like blowholes, surface roughness,
chilled surface etc. are found in sand casted machine parts. But these
can be removed by centrifugal casting machine using rotating
metallic die. Moreover, die rotation, its temperature control, and good
pouring practice can contribute to the quality of casting because of
the fact that the soundness of a casting in large part depends upon
how the metal enters into the mold or dies and solidifies. Poor
pouring practice leads to variety of casting defects such as
temperature loss, low quality casting, excessive turbulence, over
pouring etc. Besides these, handling of molten metal is very
unsecured and dangerous for the workers. In order to get rid of all
these problems, the need of an automatic pouring device arises. In
this research work, a robot assisted pouring device and a centrifugal
casting machine are designed, developed constructed and tested
experimentally which are found to work satisfactorily. The robot
assisted pouring device is further modified and developed for using it
in actual metal casting process. Lot of settings and tests are required
to control the system and ultimately it can be used in automation of
centrifugal casting machine to produce high-tech machine parts with
desired precision.
Abstract: The rising demand for format-flexible packaging
machines is caused by current market changes. Increasing the formatflexibility
is a new goal for the packaging machine manufacturers’
product development process. There are no methodical or designorientated
tools for a comprehensive consideration of this target. This
paper defines the term format-flexibility in the context of packaging
machines and shows the state-of-the-art for improving the
changeover of production machines. The requirements for a new
approach and the concept itself will be introduced, and the method
elements will be explained. Finally, the use of the concept and the
result of the development of a format-flexible packaging machine
will be shown.
Abstract: Smart metering and demand response are gaining
ground in industrial and residential applications. Smart Appliances
have been given concern towards achieving Smart home. The success
of Smart grid development relies on the successful implementation of
Information and Communication Technology (ICT) in power sector.
Smart Appliances have been the technology under development and
many new contributions to its realization have been reported in the
last few years. The role of ICT here is to capture data in real time,
thereby allowing bi-directional flow of information/data between
producing and utilization point; that lead a way for the attainment of
Smart appliances where home appliances can communicate between
themselves and provide a self-control (switch on and off) using the
signal (information) obtained from the grid. This paper depicts the
background on ICT for smart appliances paying a particular attention
to the current technology and identifying the future ICT trends for
load monitoring through which smart appliances can be achieved to
facilitate an efficient smart home system which promote demand
response program. This paper grouped and reviewed the recent
contributions, in order to establish the current state of the art and
trends of the technology, so that the reader can be provided with a
comprehensive and insightful review of where ICT for smart
appliances stands and is heading to. The paper also presents a brief
overview of communication types, and then narrowed the discussion
to the load monitoring (Non-intrusive Appliances Load Monitoring
‘NALM’). Finally, some future trends and challenges in the further
development of the ICT framework are discussed to motivate future
contributions that address open problems and explore new
possibilities.
Abstract: The UK has had its fair share of the shale gas
revolutionary waves blowing across the global oil and gas industry at
present. Although, its exploitation is widely agreed to have been
delayed, shale gas was looked upon favorably by the UK Parliament
when they recognized it as genuine energy source and granted
licenses to industry to search and extract the resource. This, although
a significant progress by industry, there yet remains another test the
UK fracking resource must pass in order to render shale gas
extraction feasible – it must be economically extractible and
sustainably so. Developing unconventional resources is much more
expensive and risky, and for shale gas wells, producing in
commercial volumes is conditional upon drilling horizontal wells and
hydraulic fracturing, techniques which increase CAPEX. Meanwhile,
investment in shale gas development projects is sensitive to gas price
and technical and geological risks. Using a Two-Factor Model, the
economics of the Bowland shale wells were analyzed and the
operational conditions under which fracking is profitable in the UK
was characterized. We find that there is a great degree of flexibility
about Opex spending; hence Opex does not pose much threat to the
fracking industry in the UK. However, we discover Bowland shale
gas wells fail to add value at gas price of $8/ Mmbtu. A minimum gas
price of $12/Mmbtu at Opex of no more than $2/ Mcf and no more
than $14.95M Capex are required to create value within the present
petroleum tax regime, in the UK fracking industry.