Abstract: Droplet size distributions in the cold spray of a fuel
are important in observed combustion behavior. Specification of
droplet size and velocity distributions in the immediate downstream
of injectors is also essential as boundary conditions for advanced
computational fluid dynamics (CFD) and two-phase spray transport
calculations. This paper describes the development of a new model to
be incorporated into maximum entropy principle (MEP) formalism
for prediction of droplet size distribution in droplet formation region.
The MEP approach can predict the most likely droplet size and
velocity distributions under a set of constraints expressing the
available information related to the distribution.
In this article, by considering the mechanisms of turbulence
generation inside the nozzle and wave growth on jet surface, it is
attempted to provide a logical framework coupling the flow inside the
nozzle to the resulting atomization process. The purpose of this paper
is to describe the formulation of this new model and to incorporate it
into the maximum entropy principle (MEP) by coupling sub-models
together using source terms of momentum and energy. Comparison
between the model prediction and experimental data for a gas turbine
swirling nozzle and an annular spray indicate good agreement
between model and experiment.
Abstract: We report in this paper the model adopted by our
system of continuous speech recognition in Arab language SySRA
and the results obtained until now. This system uses the database
Arabdic-10 which is a corpus of word for the Arab language and
which was manually segmented. Phonetic decoding is represented
by an expert system where the knowledge base is translated in the
form of production rules. This expert system transforms a vocal
signal into a phonetic lattice. The higher level of the system takes
care of the recognition of the lattice thus obtained by deferring it in
the form of written sentences (orthographical Form). This level
contains initially the lexical analyzer which is not other than the
module of recognition. We subjected this analyzer to a set of
spectrograms obtained by dictating a score of sentences in Arab
language. The rate of recognition of these sentences is about 70%
which is, to our knowledge, the best result for the recognition of the
Arab language. The test set consists of twenty sentences from four
speakers not having taken part in the training.
Abstract: In this paper we promote the Ultra Low Voltage (ULV) NAND gate to replace either partly or entirely the encryption block of a design to withstand power analysis attack.
Abstract: The importance of good requirements engineering is well documented. Agile practices, promoting collaboration and communications, facilitate the elicitation and management of volatile requirements. However, current Agile practices work in a well-defined environment. It is necessary to have a co-located customer. With distributed development it is not always possible to realize this co-location. In this environment a suitable process, possibly supported by tools, is required to support changing requirements. This paper introduces the issues of concern when managing requirements in a distributed environment and describes work done at the Software Technology Research Centre as part of the NOMAD project.
Abstract: A passive system "Qanat" is collection of some
underground wells. A mother-well was dug in a place far from the
city where they could reach to the water table maybe 100 meters
underground, they dug other wells to direct water toward the city,
with minimum possible gradient. Using the slope of the earth they
could bring water close to the surface in the city. The source of water
or the appearance of Qanat, land slope and the ownership lines are
the important and effective factors in the formation of routes and the
segment division of lands to the extent that making use of Qanat as
the techniques of extracting underground waters creates a channel of
routes with an organic order and hierarchy coinciding the slope of
land and it also guides the Qanat waters in the tradition texture of salt
desert and border provinces of it. Qanats are excavated in a specified
distinction from each other. The quantity of water provided by
Qanats depends on the kind of land, distance from mountain,
geographical situation of them and the rate of water supply from the
underground land. The rate of underground waters, possibility of
Qanat excavation, number of Qanats and rate of their water supply
from one hand and the quantity of cultivable fertile lands from the
other hand are the important natural factors making the size of cities.
In the same manner the cities with several Qanats have multi central
textures. The location of cities is in direct relation with land quality,
soil fertility and possibility of using underground water by excavating
Qanats. Observing the allowable distance for Qanat watering is a
determining factor for distance between villages and cities.
Topography, land slope, soil quality, watering system, ownership,
kind of cultivation, etc. are the effective factors in directing Qanats
for excavation and guiding water toward the cultivable lands and it
also causes the formation of different textures in land division of
farming provinces. Several divisions such as orderly and wide, inorderly,
thin and long, comb like, etc. are the introduction to organic
order. And at the same time they are complete coincidence with
environmental conditions in the typical development of ecological
architecture and planning in the traditional cities and settlements
order.
Abstract: In this paper, a novel scheme is proposed for ownership identification and authentication using color images by deploying Cryptography and Digital Watermarking as underlaying technologies. The former is used to compute the contents based hash and the latter to embed the watermark. The host image that will claim to be the rightful owner is first transformed from RGB to YST color space exclusively designed for watermarking based applications. Geometrically YS ÔèÑ T and T channel corresponds to the chrominance component of color image, therefore suitable for embedding the watermark. The T channel is divided into 4×4 nonoverlapping blocks. The size of block is important for enhanced localization, security and low computation. Each block along with ownership information is then deployed by SHA160, a one way hash function to compute the content based hash, which is always unique and resistant against birthday attack instead of using MD5 that may raise the condition i.e. H(m)=H(m'). The watermark payload varies from block to block and computed by the variance factorα . The quality of watermarked images is quite high both subjectively and objectively. Our scheme is blind, computationally fast and exactly locates the tampered region.
Abstract: Recent developments in Soft computing techniques,
power electronic switches and low-cost computational hardware have
made it possible to design and implement sophisticated control
strategies for sensorless speed control of AC motor drives. Such an
attempt has been made in this work, for Sensorless Speed Control of
Induction Motor (IM) by means of Direct Torque Fuzzy Control
(DTFC), PI-type fuzzy speed regulator and MRAS speed estimator
strategy, which is absolutely nonlinear in its nature. Direct torque
control is known to produce quick and robust response in AC drive
system. However, during steady state, torque, flux and current ripple
occurs. So, the performance of conventional DTC with PI speed
regulator can be improved by implementing fuzzy logic techniques.
Certain important issues in design including the space vector
modulated (SVM) 3-Ф voltage source inverter, DTFC design,
generation of reference torque using PI-type fuzzy speed regulator
and sensor less speed estimator have been resolved. The proposed
scheme is validated through extensive numerical simulations on
MATLAB. The simulated results indicate the sensor less speed
control of IM with DTFC and PI-type fuzzy speed regulator provides
satisfactory high dynamic and static performance compare to
conventional DTC with PI speed regulator.
Abstract: In this work social stratification is considered as one
of significant factor which generate the phenomena “terrorism” and it
puts the accent on correlation connection between them, with the
object of creation info-logical model generation of phenomena of
“terrorism” based on stratification process.
Abstract: Agricultural residue such as oil palm fronds (OPF) is
cheap, widespread and available throughout the year. Hemicelluloses
extracted from OPF can be hydrolyzed to their monomers and used in
production of xylooligosaccharides (XOs). The objective of the
present study was to optimize the enzymatic hydrolysis process of
OPF hemicellulose by varying pH, temperature, enzyme and substrate
concentration for production of XOs. Hemicelluloses was extracted
from OPF by using 3 M potassium hydroxide (KOH) at temperature of
40°C for 4 hrs and stirred at 400 rpm. The hemicellulose was then
hydrolyzed using Trichoderma longibrachiatum xylanase at different
pH, temperature, enzyme and substrate concentration. XOs were
characterized based on reducing sugar determination. The optimum
conditions to produced XOs from OPF hemicellulose was obtained at
pH 4.6, temperature of 40°C , enzyme concentration of 2 U/mL and
2% substrate concentration. The results established the suitability of
oil palm fronds as raw material for production of XOs.
Abstract: The coastal sediments of West Port of Malaysia was monitored from Nov. 2009 to Oct. 2010 to assess spatial distribution of heavy metals As, Cu, Cd, Cr, Hg, Ni, Zn and Pb. Sediment samples were collected from 10 stations in dry and rainy season in West Port. The range concentrations measured (Mg/g dry weight ) were from 23.4 to 98.3 for Zn, 22.3 to 80 for Pb, 7.4 to 27.6 Cu, 0.244 to 3.53 for Cd, 7.2 to 22.2 for Ni, 20.2 to 162 for As, 0.11 to 0.409 for Hg and 11.5 to 61.5 for Cr. The geochemical indexes used in this study were Geoaccumulation (Igeo), Contamination Factor (CF) and Pollution Load Index (PLI); these indexes were used to evaluate the levels of sediment contaminations. The results of these indexes show that, the status of West Port sediment quality are moderately polluted by heavy metals except in arsenic which shows the high level of pollution.
Abstract: The purpose of this study is to discuss the effect of the
intervention of exercise behavior change plan for high school students
on study subjects- social and psychological factors and exercise
stages. This research uses the transtheoretical model as the research
framework. One experiment group and one control group were used in
a quasi-experimental design research. The experimental group
accepted health-related physical fitness course and the traditional
course; the control group accepted traditional physical education
course. There is a significant difference before and after the
intervention in the experimental group. Karl-s test shows the
experimental group gained a better improvement than that in the
control group. The Analysis of Covariance had shown the exercise
stages (F=7.62, p
Abstract: Power consumption of nodes in ad hoc networks is a
critical issue as they predominantly operate on batteries. In order to
improve the lifetime of an ad hoc network, all the nodes must be
utilized evenly and the power required for connections must be
minimized. In this project a link layer algorithm known as Power
Aware medium Access Control (PAMAC) protocol is proposed
which enables the network layer to select a route with minimum total
power requirement among the possible routes between a source and a
destination provided all nodes in the routes have battery capacity
above a threshold. When the battery capacity goes below a
predefined threshold, routes going through these nodes will be
avoided and these nodes will act only as source and destination.
Further, the first few nodes whose battery power drained to the set
threshold value are pushed to the exterior part of the network and the
nodes in the exterior are brought to the interior. Since less total
power is required to forward packets for each connection. The
network layer protocol AOMDV is basically an extension to the
AODV routing protocol. AOMDV is designed to form multiple
routes to the destination and it also avoid the loop formation so that it
reduces the unnecessary congestion to the channel. In this project, the
performance of AOMDV is evaluated using PAMAC as a MAC layer
protocol and the average power consumption, throughput and
average end to end delay of the network are calculated and the results
are compared with that of the other network layer protocol AODV.
Abstract: Simultaneous effects of temperature, immersion time, salt concentration, sucrose concentration, pressure and convective dryer temperature on the combined osmotic dehydration - convective drying of edible button mushrooms were investigated. Experiments were designed according to Central Composite Design with six factors each at five different levels. Response Surface Methodology (RSM) was used to determine the optimum processing conditions that yield maximum water loss and rehydration ratio and minimum solid gain and shrinkage in osmotic-convective drying of edible button mushrooms. Applying surfaces profiler and contour plots optimum operation conditions were found to be temperature of 39 °C, immersion time of 164 min, salt concentration of 14%, sucrose concentration of 53%, pressure of 600 mbar and drying temperature of 40 °C. At these optimum conditions, water loss, solid gain, rehydration ratio and shrinkage were found to be 63.38 (g/100 g initial sample), 3.17 (g/100 g initial sample), 2.26 and 7.15%, respectively.
Abstract: Sensor networks are often deployed in unattended
environments, thus leaving these networks vulnerable to false data
injection attacks in which an adversary injects forged reports into the
network through compromised nodes, with the goal of deceiving the
base station or depleting the resources of forwarding nodes. Several
research solutions have been recently proposed to detect and drop such
forged reports during the forwarding process. Each design can provide
the equivalent resilience in terms of node compromising. However,
their energy consumption characteristics differ from each other. Thus,
employing only a single filtering scheme for a network is not a
recommendable strategy in terms of energy saving. It's very important
the threshold determination for message authentication to identify. We
propose the recursive contract net protocols which less energy level of
terminal node in wireless sensor network.
Abstract: All over the world, including the Middle and East
European countries, sustainable tillage and sowing technologies are
applied increasingly broadly with a view to optimising soil resources,
mitigating soil degradation processes, saving energy resources,
preserving biological diversity, etc. As a result, altered conditions of
tillage and sowing technological processes are faced inevitably. The
purpose of this study is to determine the seedbed topsoil hardness
when using a combined sowing coulter in different sustainable tillage
technologies. The research involved a combined coulter consisting
of two dissected blade discs and a shoe coulter. In order to determine
soil hardness at the seedbed area, a multipenetrometer was used. It
was found by experimental studies that in loosened soil, a combined
sowing coulter equally suppresses the furrow bottom, walls and soil
near the furrow; therefore, here, soil hardness was similar at all
researched depths and no significant differences were established. In
loosened and compacted (double-rolled) soil, the impact of a
combined coulter on the hardness of seedbed soil surface was more
considerable at a depth of 2 mm. Soil hardness at the furrow bottom
and walls to a distance of up to 26 mm was 1.1 MPa. At a depth of 10
mm, the greatest hardness was established at the furrow bottom. In
loosened and heavily compacted (rolled for 6 times) soil, at a depth
of 2 and 10 mm a combined coulter most of all compacted the furrow
bottom, which has a hardness of 1.8 MPa. At a depth of 20 mm, soil
hardness within the whole investigated area varied insignificantly and
fluctuated by around 2.0 MPa. The hardness of furrow walls and soil
near the furrow was by approximately 1.0 MPa lower than that at the
furrow bottom
Abstract: The compression-absorption heat pump (C-A HP), one
of the promising heat recovery equipments that make process hot
water using low temperature heat of wastewater, was evaluated by
computer simulation. A simulation program was developed based on
the continuity and the first and second laws of thermodynamics. Both
the absorber and desorber were modeled using UA-LMTD method. In
order to prevent an unfeasible temperature profile and to reduce
calculation errors from the curved temperature profile of a mixture,
heat loads were divided into lots of segments. A single-stage
compressor was considered. A compressor cooling load was also
taken into account. An isentropic efficiency was computed from the
map data. Simulation conditions were given based on the system
consisting of ordinarily designed components. The simulation results
show that most of the total entropy generation occurs during the
compression and cooling process, thus suggesting the possibility that
system performance can be enhanced if a rectifier is introduced.
Abstract: This article presents the developments of efficient
algorithms for tablet copies comparison. Image recognition has
specialized use in digital systems such as medical imaging,
computer vision, defense, communication etc. Comparison between
two images that look indistinguishable is a formidable task. Two
images taken from different sources might look identical but due to
different digitizing properties they are not. Whereas small variation
in image information such as cropping, rotation, and slight
photometric alteration are unsuitable for based matching
techniques. In this paper we introduce different matching
algorithms designed to facilitate, for art centers, identifying real
painting images from fake ones. Different vision algorithms for
local image features are implemented using MATLAB. In this
framework a Table Comparison Computer Tool “TCCT" is
designed to facilitate our research. The TCCT is a Graphical Unit
Interface (GUI) tool used to identify images by its shapes and
objects. Parameter of vision system is fully accessible to user
through this graphical unit interface. And then for matching, it
applies different description technique that can identify exact
figures of objects.
Abstract: The increasing demand for sufficient and clean
energy forces industrial and service companies to align their strategies towards efficient consumption. This trend refers also to the
residential building sector. There, large amounts of energy consumption are caused by house and facility heating. Many of the
operated hot water heating systems lack hydraulic balanced working
conditions for heat distribution and –transmission and lead to
inefficient heating. Through hydraulic balancing of heating systems,
significant energy savings for primary and secondary energy can be
achieved. This paper addresses the use of KNX-technology (Smart
Buildings) in residential buildings to ensure a dynamic adaption of
hydraulic system's performance, in order to increase the heating
system's efficiency. In this paper, the procedure of heating system
segmentation into hydraulically independent units (meshes) is
presented. Within these meshes, the heating valve are addressed and
controlled by a central facility server. Feasibility criteria towards
such drivers will be named. The dynamic hydraulic balance is
achieved by positioning these valves according to heating loads, that
are generated from the temperature settings in the corresponding
rooms. The energetic advantages of single room heating control
procedures, based on the application FacilityManager, is presented.
Abstract: With the advance of information technology in the
new era the applications of Internet to access data resources has
steadily increased and huge amount of data have become accessible
in various forms. Obviously, the network providers and agencies,
look after to prevent electronic attacks that may be harmful or may
be related to terrorist applications. Thus, these have facilitated the
authorities to under take a variety of methods to protect the special
regions from harmful data. One of the most important approaches is
to use firewall in the network facilities. The main objectives of
firewalls are to stop the transfer of suspicious packets in several
ways. However because of its blind packet stopping, high process
power requirements and expensive prices some of the providers are
reluctant to use the firewall. In this paper we proposed a method to
find a discriminate function to distinguish between usual packets and
harmful ones by the statistical processing on the network router logs.
By discriminating these data, an administrator may take an approach
action against the user. This method is very fast and can be used
simply in adjacent with the Internet routers.
Abstract: Stream Control Transmission Protocol (SCTP) has been
proposed to provide reliable transport of real-time communications.
Due to its attractive features, such as multi-streaming and multihoming,
the SCTP is often expected to be an alternative protocol
for TCP and UDP. In the original SCTP standard, the secondary path
is mainly regarded as a redundancy. Recently, most of researches
have focused on extending the SCTP to enable a host to send its
packets to a destination over multiple paths simultaneously. In order
to transfer packets concurrently over the multiple paths, the SCTP
should be well designed to avoid unnecessary fast retransmission
and the mis-estimation of congestion window size through the paths.
Therefore, we propose an Enhanced Cooperative ACK SCTP (ECASCTP)
to improve the path recovery efficiency of multi-homed host
which is under concurrent multiple transfer mode. We evaluated the
performance of our proposed scheme using ns-2 simulation in terms
of cwnd variation, path recovery time, and goodput. Our scheme
provides better performance in lossy and path asymmetric networks.