Abstract: In this paper, we propose a novel adaptive voltage control strategy for boost converter via Inverse LQ Servo-Control. Our presented strategy is based on an analytical formula of Inverse Linear Quadratic (ILQ) design method, which is not necessary to solve Riccati’s equation directly. The optimal and adaptive controller of the voltage control system is designed. The stability and the robust control are analyzed. Whereas, we can get the analytical solution for the optimal and robust voltage control is achieved through the natural angular velocity within a single parameter and we can change the responses easily via the ILQ control theory. Our method provides effective results as the stable responses and the response times are not drifted even if the condition is changed widely.
Abstract: In the real application of active control systems to
mitigate the response of structures subjected to sever external
excitations such as earthquake and wind induced vibrations, since the
capacity of actuators is limited then the actuators saturate. Hence, in
designing controllers for linear and nonlinear structures under sever
earthquakes, the actuator saturation should be considered as a
constraint. In this paper optimal design of active controllers for
nonlinear structures by considering the actuator saturation has been
studied. To this end a method has been proposed based on defining
an optimization problem which considers the minimizing of the
maximum displacement of the structure as objective when a limited
capacity for actuator has been used as a constraint in optimization
problem. To evaluate the effectiveness of the proposed method, a
single degree of freedom (SDF) structure with a bilinear hysteretic
behavior has been simulated under a white noise ground acceleration
of different amplitudes. Active tendon control mechanism, comprised
of pre-stressed tendons and an actuator, and extended nonlinear
Newmark method based instantaneous optimal control algorithm
have been used as active control mechanism and algorithm. To
enhance the efficiency of the controllers, the weights corresponding
to displacement, velocity, acceleration and control force in the
performance index have been found by using the Distributed Genetic
Algorithm (DGA). According to the results it has been concluded
that the proposed method has been effective in considering the
actuator saturation in designing optimal controllers for nonlinear
frames. Also it has been shown that the actuator capacity and the
average value of required control force are two important factors in
designing nonlinear controllers for considering the actuator
saturation.
Abstract: Nowadays over-consumption of fossil energy in
buildings especially in residential buildings and also considering the
increase in populations, the crisis of energy shortage in a near future
is predictable. The recent performance of developed countries in
construction with the aim of decreasing fossil energies shows that
these countries have understood the incoming crisis and has taken
reasonable and basic actions in this regard. However, Iranian
architecture, with several thousands years of history, has acquired
and executed invaluable experiences in designing, adapting and
coordinating with the nature.
Architectural studies during the recent decades show that imitating
modern western architecture results in high energy wastage beside
the fact that it not reasonably adaptable and corresponded with the
habits and customs of people unlike the architecture in the past which
was compatible and adaptable with the climatic conditions and this
necessitates optimal using of renewable energies more than ever. This
paper studies problems of design, execution and living in today's
houses and reviews the characteristics of climatic elements paying
special attention to the performance of trombe wall and solar
greenhouse in traditional houses and offers some suggestions for
combining these two elements and a climatic strategy.
Abstract: In the present research, steam cracking of two types of
feedstocks i.e., naphtha and ethane is simulated for Pyrocrack1-1 and
2/2 coil configurations considering two key parameters of coil outlet
temperature (COT) and coil capacity using a radical based kinetic
model. The computer model is confirmed using the industrial data
obtained from Amirkabir Petrochemical Complex. The results are in
good agreement with performance data for naphtha cracking in a
wide range of severity (0.4-0.7), and for ethane cracking on various
conversions (50-70). It was found that Pyrocrack2-2 coil type is an
appropriate choice for steam cracking of ethane at reasonable
ethylene yield while resulting in much lower tube wall temperature
while Pyrocrack1-1 coil type is a proper selection for liquid
feedstocks i.e. naphtha. It can be used for cracking of liquid
feedstocks at optimal ethylene yield whereas not exceeding the
allowable maximum tube temperature.
Abstract: The classic problem of recovering arbitrary values of
a band-limited signal from its samples has an added complication
in software radio applications; namely, the resampling calculations
inevitably fold aliases of the analog signal back into the original
bandwidth. The phenomenon is quantified by the spur-free dynamic
range. We demonstrate how a novel application of the Remez (Parks-
McClellan) algorithm permits optimal signal recovery and SFDR, far
surpassing state-of-the-art resamplers.
Abstract: We propose a multi-agent based utilitarian approach
to model and understand information flows in social networks that
lead to Pareto optimal informational exchanges. We model the
individual expected utility function of the agents to reflect the net
value of information received. We show how this model, adapted
from a theorem by Karl Borch dealing with an actuarial Risk
Exchange concept in the Insurance industry, can be used for social
network analysis. We develop a utilitarian framework that allows us
to interpret Pareto optimal exchanges of value as potential
information flows, while achieving a maximization of a sum of
expected utilities of information of the group of agents. We examine
some interesting conditions on the utility function under which the
flows are optimal. We illustrate the promise of this new approach to
attach economic value to information in networks with a synthetic
example.
Abstract: The problem of updating damped gyroscopic systems using measured modal data can be mathematically formulated as following two problems. Problem I: Given Ma ∈ Rn×n, Λ = diag{λ1, ··· , λp} ∈ Cp×p, X = [x1, ··· , xp] ∈ Cn×p, where p
Abstract: The current study describes a multi-objective optimization technique for positioning of houses in a residential neighborhood. The main task is the placement of residential houses in a favorable configuration satisfying a number of objectives. Solving the house layout problem is a challenging task. It requires an iterative approach to satisfy design requirements (e.g. energy efficiency, skyview, daylight, roads network, visual privacy, and clear access to favorite views). These design requirements vary from one project to another based on location and client preferences. In the Gulf region, the most important socio-cultural factor is the visual privacy in indoor space. Hence, most of the residential houses in this region are surrounded by high fences to provide privacy, which has a direct impact on other requirements (e.g. daylight and direction to favorite views). This investigation introduces a novel technique to optimally locate and orient residential buildings to satisfy a set of design requirements. The developed technique explores the search space for possible solutions. This study considers two dimensional house planning problems. However, it can be extended to solve three dimensional cases.
Abstract: A new stochastic algorithm called Probabilistic Global Search Johor (PGSJ) has recently been established for global optimization of nonconvex real valued problems on finite dimensional Euclidean space. In this paper we present convergence guarantee for this algorithm in probabilistic sense without imposing any more condition. Then, we jointly utilize this algorithm along with control
parameterization technique for the solution of constrained optimal control problem. The numerical simulations are also included to illustrate the efficiency and effectiveness of the PGSJ algorithm in the solution of control problems.
Abstract: In this paper, periodic force operation of a wastewater treatment process has been studied for the improved process performance. A previously developed dynamic model for the process is used to conduct the performance analysis. The static version of the model was utilized first to determine the optimal productivity conditions for the process. Then, feed flow rate in terms of dilution rate i.e. (D) is transformed into sinusoidal function. Nonlinear model predictive control algorithm is utilized to regulate the amplitude and period of the sinusoidal function. The parameters of the feed cyclic functions are determined which resulted in improved productivity than the optimal productivity under steady state conditions. The improvement in productivity is found to be marginal and is satisfactory in substrate conversion compared to that of the optimal condition and to the steady state condition, which corresponds to the average value of the periodic function. Successful results were also obtained in the presence of modeling errors and external disturbances.
Abstract: This paper focuses on a technique for identifying the geological boundary of the ground strata in front of a tunnel excavation site using the first order adjoint method based on the optimal control theory. The geological boundary is defined as the boundary which is different layers of elastic modulus. At tunnel excavations, it is important to presume the ground situation ahead of the cutting face beforehand. Excavating into weak strata or fault fracture zones may cause extension of the construction work and human suffering. A theory for determining the geological boundary of the ground in a numerical manner is investigated, employing excavating blasts and its vibration waves as the observation references. According to the optimal control theory, the performance function described by the square sum of the residuals between computed and observed velocities is minimized. The boundary layer is determined by minimizing the performance function. The elastic analysis governed by the Navier equation is carried out, assuming the ground as an elastic body with linear viscous damping. To identify the boundary, the gradient of the performance function with respect to the geological boundary can be calculated using the adjoint equation. The weighed gradient method is effectively applied to the minimization algorithm. To solve the governing and adjoint equations, the Galerkin finite element method and the average acceleration method are employed for the spatial and temporal discretizations, respectively. Based on the method presented in this paper, the different boundary of three strata can be identified. For the numerical studies, the Suemune tunnel excavation site is employed. At first, the blasting force is identified in order to perform the accuracy improvement of analysis. We identify the geological boundary after the estimation of blasting force. With this identification procedure, the numerical analysis results which almost correspond with the observation data were provided.
Abstract: This paper considers a multi criteria cell formation
problem in Cellular Manufacturing System (CMS). Minimizing the
number of voids and exceptional elements in cells simultaneously are
two proposed objective functions. This problem is an Np-hard
problem according to the literature, and therefore, we can-t find the
optimal solution by an exact method. In this paper we developed two
ant algorithms, Ant Colony Optimization (ACO) and Max-Min Ant
System (MMAS), based on Data Envelopment Analysis (DEA). Both
of them try to find the efficient solutions based on efficiency concept
in DEA. Each artificial ant is considered as a Decision Making Unit
(DMU). For each DMU we considered two inputs, the values of
objective functions, and one output, the value of one for all of them.
In order to evaluate performance of proposed methods we provided
an experimental design with some empirical problem in three
different sizes, small, medium and large. We defined three different
criteria that show which algorithm has the best performance.
Abstract: A. niger XP isolated from Vietnam produces very low amount of acidic phytase with optimal pH at 2.5 and 5.5. The phytase production of this strain was successfully improved through gene cloning and expression. A 1.4 - kb DNA fragment containing the coding region of the phyA gene was amplified by PCR and inserted into the expression vector pPICZαA with a signal peptide α- factor, under the control of AOX1 promoter. The recombined plasmid was transformed into the host strain P. pastoris KM71H and X33 by electroporation. Both host strains could efficiently express and secret phytase. The multicopy strains were screened for over expression of phytase. All the selected multicopy strains of P. pastoris X33 were examined for phytase activity, the maximum phytase yield of 1329 IU/ml was obtained after 4 days of incubation in medium BMM. The recombinant protein with MW of 97.4 KW showed to be the only one protein secreted in the culture broth. Multicopy transformant P. pastoris X33 supposed to be potential candidate for producing the commercial preparation of phytase.
Abstract: In this study, an optimization of supersonic air-to-air ejector is carried out by a recently developed single-objective genetic algorithm based on adaption of sequence of individuals. Adaptation of sequence is based on Shape-based distance of individuals and embedded micro-genetic algorithm. The optimal sequence found defines the succession of CFD-aimed objective calculation within each generation of regular micro-genetic algorithm. A spring-based deformation mutates the computational grid starting the initial individualvia adapted population in the optimized sequence. Selection of a generation initial individual is knowledge-based. A direct comparison of the newly defined and standard micro-genetic algorithm is carried out for supersonic air-to-air ejector. The only objective is to minimize the loose of total stagnation pressure in the ejector. The result is that sequence-adopted micro-genetic algorithm can provide comparative results to standard algorithm but in significantly lower number of overall CFD iteration steps.
Abstract: Designing a simulated system and training it to optimize its tasks in simulated environment helps the designers to avoid problems that may appear when designing the system directly in real world. These problems are: time consuming, high cost, high errors percentage and low efficiency and accuracy of the system. The proposed system will investigate and improve the efficiency and accuracy of a simulated robot to choose correct behavior to perform its task. In this paper, machine learning, which uses genetic algorithm, is adopted. This type of machine learning is called genetic-based machine learning in which a distributed classifier system is used to improve the efficiency and accuracy of the robot. Consequently, it helps the robot to achieve optimal action.
Abstract: The geometric errors in the manufacturing process can
be reduced by optimal positioning of the fixture elements in the
fixture to make the workpiece stiff. We propose a new fixture layout
optimization method N-3-2-1 for large metal sheets in this paper that
combines the genetic algorithm and finite element analysis. The
objective function in this method is to minimize the sum of the nodal
deflection normal to the surface of the workpiece. Two different
kinds of case studies are presented, and optimal position of the
fixturing element is obtained for different cases.
Abstract: In this paper, a novel associative memory model will be proposed and applied to memory retrievals based on the conventional continuous time model. The conventional model presents memory capacity is very low and retrieval process easily converges to an equilibrium state which is very different from the stored patterns. Genetic Algorithms is well-known with the capability of global optimal search escaping local optimum on progress to reach a global optimum. Based on the well-known idea of Genetic Algorithms, this work proposes a heuristic rule to make a mutation when the state of the network is trapped in a spurious memory. The proposal heuristic associative memory show the stored capacity does not depend on the number of stored patterns and the retrieval ability is up to ~ 1.
Abstract: Permanent magnet synchronous machines are known
as a good candidate for hybrid electric vehicles due to their unique
merits. However they have two major drawbacks i.e. high cost and
small speed range. In this paper an optimal design of a permanent
magnet machine is presented. A reduction of permanent magnet
material for a constant torque and an extension in speed and torque
ranges are chosen as the optimization aims. For this purpose the
analytical model of the permanent magnet synchronous machine is
derived and the appropriate design algorithm is devised. The genetic
algorithm is then employed to optimize some machine specifications.
Finally the finite element method is used to validate the designed
machine.
Abstract: In this work, grinding or microcutting tools in the form of pellets were manufactured using a bounded alumina abrasive grains. The bound used is a vitreous material containing quartz feldspars, kaolinite and a quantity of hematite. The pellets were used in glass grinding process to replace the free abrasive grains lapping process. The study of the elaborated pellets were done to define their effectiveness in the grinding process and to optimize the influence of the pellets elaboration parameters. The obtained results show the existence of an optimal combination of the pellets elaboration parameters for each glass grinding phase (coarse to fine grinding). The final roughness (rms) reached by the elaborated pellets on a BK7 glass surface was about 0.392 μm.
Abstract: In order to enhance the usability of the human computer interface (HCI) on the touchscreen, this study explored the optimal tactile depth and effect of visual cues on the user-s tendency to touch the touchscreen icons. The experimental program was designed on the touchscreen in this study. Results indicated that the ratio of the icon size to the tactile depth was 1:0.106. There were significant effects of experienced users and novices on the tactile feedback depth (p < 0.01). In addition, the results proved that the visual cues provided a feedback that helped to guide the user-s touch icons accurately and increased the capture efficiency for a tactile recognition field. This tactile recognition field was 18.6 mm in length. There was consistency between the experienced users and novices under the visual cue effects. Finally, the study developed an applied design with touch feedback for touchscreen icons.