Abstract: Milk from differently fed cows (supplemented with carotenoids from carrots or palm oil product Carotino CAF 100) was obtained in a conventional dairy farm to assess the carotenoid potential to protect milk fat against oxidation. The extracted anhydrous milk fat (AMF) was tested by peroxide value, and Rancimat tests. Temperature, and light stimulation for reaction acceleration was used. The oxidative stability enhancement by carotenoids was detected in peroxide value test – the strongest effect was observed in palm oil, following by carrot supplemented group, compared to control group, whose feed was unchanged. Rancimat accelerated oxidation test results did not show any superiority of the oxidative stability of the AMF samples from milk of the carotenoidsupplemented cow groups. The average oxidation stability of AMF dark-stored samples was 12.59 ± 0.294 h, and it was significantly (p < 0.05) higher than that of AMF light-affected samples, i.e. 2.60 ± 0.191 h.
Abstract: A multi-block algorithm and its implementation in two-dimensional finite element numerical model CCHE2D are presented. In addition to a conventional Lagrangian Interpolation Method (LIM), a novel interpolation method, called Consistent Interpolation Method (CIM), is proposed for more accurate information transfer across the interfaces. The consistent interpolation solves the governing equations over the auxiliary elements constructed around the interpolation nodes using the same numerical scheme used for the internal computational nodes. With the CIM, the momentum conservation can be maintained as well as the mass conservation. An imbalance correction scheme is used to enforce the conservation laws (mass and momentum) across the interfaces. Comparisons of the LIM and the CIM are made using several flow simulation examples. It is shown that the proposed CIM is physically more accurate and produces satisfactory results efficiently.
Abstract: The rapid improvement of the microprocessor and network has made it possible for the PC cluster to compete with conventional supercomputers. Lots of high throughput type of applications can be satisfied by using the current desktop PCs, especially for those in PC classrooms, and leave the supercomputers for the demands from large scale high performance parallel computations. This paper presents our development on enabling an automated deployment mechanism for cluster computing to utilize the computing power of PCs such as reside in PC classroom. After well deployment, these PCs can be transformed into a pre-configured cluster computing resource immediately without touching the existing education/training environment installed on these PCs. Thus, the training activities will not be affected by this additional activity to harvest idle computing cycles. The time and manpower required to build and manage a computing platform in geographically distributed PC classrooms also can be reduced by this development.
Abstract: This paper attempts to model and design a simple
fuzzy logic controller with Variable Reference. The Variable
Reference (VR) is featured as an adaptability element which is
obtained from two known variables – desired system-input and actual
system-output. A simple fuzzy rule-based technique is simulated to
show how the actual system-input is gradually tuned in to a value
that closely matches the desired input. The designed controller is
implemented and verified on a simple heater which is controlled by
PIC Microcontroller harnessed by a code developed in embedded C.
The output response of the PIC-controlled heater is analyzed and
compared to the performances by conventional fuzzy logic
controllers. The novelty of this work lies in the fact that it gives
better performance by using less number of rules compared to
conventional fuzzy logic controllers.
Abstract: The motivation for adaptive modulation and coding is
to adjust the method of transmission to ensure that the maximum
efficiency is achieved over the link at all times. The receiver
estimates the channel quality and reports it back to the transmitter.
The transmitter then maps the reported quality into a link mode. This
mapping however, is not a one-to-one mapping. In this paper we
investigate a method for selecting the proper modulation scheme.
This method can dynamically adapt the mapping of the Signal-to-
Noise Ratio (SNR) into a link mode. It enables the use of the right
modulation scheme irrespective of changes in the channel conditions
by incorporating errors in the received data. We propose a Markov
model for this method, and use it to derive the average switching
thresholds and the average throughput. We show that the average
throughput of this method outperforms the conventional threshold
method.
Abstract: The approaches to make an agent generate intelligent actions in the AI field might be roughly categorized into two ways–the classical planning and situated action system. It is well known that each system have its own strength and weakness. However, each system also has its own application field. In particular, most of situated action systems do not directly deal with the logical problem. This paper first briefly mentions the novel action generator to situatedly extract a set of actions, which is likely to help to achieve the goal at the current situation in the relaxed logical space. After performing the action set, the agent should recognize the situation for deciding the next likely action set. However, since the extracted action is an approximation of the action which helps to achieve the goal, the agent could be caught into the deadlock of the problem. This paper proposes the newly developed hybrid architecture to solve the problem, which combines the novel situated action generator with the conventional planner. The empirical result in some planning domains shows that the quality of the resultant path to the goal is mostly acceptable as well as deriving the fast response time, and suggests the correlation between the structure of problems and the organization of each system which generates the action.
Abstract: Distributed Power generation has gained a lot of
attention in recent times due to constraints associated with
conventional power generation and new advancements in DG
technologies .The need to operate the power system economically
and with optimum levels of reliability has further led to an increase
in interest in Distributed Generation. However it is important to place
Distributed Generator on an optimum location so that the purpose of
loss minimization and voltage regulation is dully served on the
feeder. This paper investigates the impact of DG units installation on
electric losses, reliability and voltage profile of distribution networks.
In this paper, our aim would be to find optimal distributed
generation allocation for loss reduction subjected to constraint of
voltage regulation in distribution network. The system is further
analyzed for increased levels of Reliability. Distributed Generator
offers the additional advantage of increase in reliability levels as
suggested by the improvements in various reliability indices such as
SAIDI, CAIDI and AENS. Comparative studies are performed and
related results are addressed. An analytical technique is used in order
to find the optimal location of Distributed Generator. The suggested
technique is programmed under MATLAB software. The results
clearly indicate that DG can reduce the electrical line loss while
simultaneously improving the reliability of the system.
Abstract: Saccharomyces cerevisiae (baker-s yeast) can exhibit
sustained oscillations during the operation in a continuous bioreactor
that adversely affects its stability and productivity. Because of
heterogeneous nature of cell populations, the cell population balance
models can be used to capture the dynamic behavior of such cultures.
In this paper an unstructured, segregated model is used which is
based on population balance equation(PBE) and then in order to
simulation, the 4th order Rung-Kutta is used for time dimension and
three methods, finite difference, orthogonal collocation on finite
elements and Galerkin finite element are used for discretization of the
cell mass domain. The results indicate that the orthogonal collocation
on finite element not only is able to predict the oscillating behavior of
the cell culture but also needs much little time for calculations.
Therefore this method is preferred in comparison with other methods.
In the next step two controllers, a globally linearizing control (GLC)
and a conventional proportional-integral (PI) controller are designed
for controlling the total cell mass per unit volume, and performances
of these controllers are compared through simulation. The results
show that although the PI controller has simpler structure, the GLC
has better performance.
Abstract: During recent years wind turbine technology has
undergone rapid developments. Growth in size and the optimization
of wind turbines has enabled wind energy to become increasingly
competitive with conventional energy sources. As a result today-s
wind turbines participate actively in the power production of several
countries around the world. These developments raise a number of
challenges to be dealt with now and in the future. The penetration of
wind energy in the grid raises questions about the compatibility of the
wind turbine power production with the grid. In particular, the
contribution to grid stability, power quality and behavior during fault
situations plays therefore as important a role as the reliability. In the
present work, we addressed two fault situations that have shown their
influence on the generator and the behavior of the wind over the
defects which are briefly discussed based on simulation results.
Abstract: The objective of this paper is to compare the time
specification performance between conventional controller PID and
modern controller SMC for an inverted pendulum system. The goal is
to determine which control strategy delivers better performance with
respect to pendulum-s angle and cart-s position. The inverted
pendulum represents a challenging control problem, which
continually moves toward an uncontrolled state. Two controllers are
presented such as Sliding Mode Control (SMC) and Proportional-
Integral-Derivatives (PID) controllers for controlling the highly
nonlinear system of inverted pendulum model. Simulation study has
been done in Matlab Mfile and simulink environment shows that both
controllers are capable to control multi output inverted pendulum
system successfully. The result shows that Sliding Mode Control
(SMC) produced better response compared to PID control strategies
and the responses are presented in time domain with the details
analysis.
Abstract: One of the disadvantages of using OFDM is the larger
peak to averaged power ratio (PAPR) in its time domain signal. The
larger PAPR signal would course the fatal degradation of bit error
rate performance (BER) due to the inter-modulation noise in the nonlinear
channel. This paper proposes an improved DSI (Dummy
Sequence Insertion) method, which can achieve the better PAPR and
BER performances. The feature of proposed method is to optimize
the phase of each dummy sub-carrier so as to reduce the PAPR
performance by changing all predetermined phase coefficients in the
time domain signal, which is calculated for data sub-carriers and
dummy sub-carriers separately. To achieve the better PAPR
performance, this paper also proposes to employ the time-frequency
domain swapping algorithm for fine adjustment of phase coefficient
of the dummy subcarriers, which can achieve the less complexity of
processing and achieves the better PAPR and BER performances
than those for the conventional DSI method. This paper presents
various computer simulation results to verify the effectiveness of
proposed method as comparing with the conventional methods in the
non-linear channel.
Abstract: Brucellosis is a zoonotic disease; its symptoms and appearances are not exclusive in human and its traditional diagnosis is based on culture, serological methods and conventional PCR. For more sensitive, specific detection and differentiation of Brucella spp., the real time PCR method is recommended. This research has performed to determine the presence and prevalence of Brucella spp. and differentiation of Brucella abortus and Brucella melitensis in house mouse (Mus musculus) in west of Iran. A TaqMan analysis and single-step PCR was carried out in total 326 DNA of Mouse's spleen samples. From the total number of 326 samples, 128 (39.27%) gave positive results for Brucella spp. by conventional PCR, also 65 and 32 out of the 128 specimens were positive for B. melitensis, B. abortus, respectively. These results indicate a high presence of this pathogen in this area and that real time PCR is considerably faster than current standard methods for identification and differentiation of Brucella species. To our knowledge, this study is the first prevalence report of direct identification and differentiation of B. abortus and B. melitensis by real time PCR in mouse tissue samples in Iran.
Abstract: In this paper we propose a blind algorithm for peakto- average power ratio (PAPR) reduction in OFDM systems, based on selected mapping (SLM) algorithm as a distortionless method. The main drawback of the conventional SLM technique is the need for transmission of several side information bits, for each data block, which results in loss in data rate transmission. In the proposed method some special number of carriers in the OFDM frame is reserved to be rotated with one of the possible phases according to the number of phase sequence blocks in SLM algorithm. Reserving some limited number of carriers wont effect the reduction in PAPR of OFDM signal. Simulation results show using ML criteria at the receiver will lead to the same system-performance as the conventional SLM algorithm, while there is no need to send any side information to the receiver.
Abstract: A seismic isolation pad produced by utilizing the scrap
tire rubber which contains interleaved steel reinforcing cords has been
proposed. The steel cords are expected to function similar to the steel
plates used in conventional laminated rubber bearings. The scrap tire
rubber pad (STRP) isolator is intended to be used in low rise
residential buildings of highly seismic areas of the developing
countries. Experimental investigation was conducted on unbonded
STRP isolators, and test results provided useful information including
stiffness, damping values and an eventual instability of the isolation
unit. Finite element analysis (FE analysis) of STRP isolator was
carried out on properly bonded samples. These types of isolators
provide positive incremental force resisting capacity up to shear strain
level of 155%. This paper briefly discusses the force deformation
behavior of bonded STRP isolators including stability of the isolation
unit.
Abstract: A novel interpolation scheme to extend usable spectrum
and upconvert in high performance D/A converters is addressed in this
paper. By adjusting the pulse width of cycle and the production circuit
of code, the expansion code is a null code or complementary code that
is interpolation process. What the times and codes of interpolation
decide DAC works in one of a normal mode or multi-mixer mode
so that convert the input digital data signal into normal signal or a
mixed analog signal having a mixer frequency that is higher than the
data frequency. Simulation results show that the novel scheme and
apparatus most extend the usable frequency spectrum into fifth to
sixth Nyquist zone beyond conventional DACs.
Abstract: In this study, mechanically alloyed Al 2024 powder is
densified by conventional sintering and by equal channel angular
pressing (ECAP) with and without back pressure. The powder was
encapsulated in an aluminium can for consolidation through ECAP.
The properties obtained in the compacts by conventional sintering
route and by ECAP are compared. The effect of conventional
sintering and ECAP on consolidation behaviour of powder,
microstructure, density and hardness is discussed. Room temperature
back pressure aided ECAP results in nearly full denser (97% of its
theoretical density) compact at room temperature. NanoIndentation
technique was used to determine the modulus of the consolidated
compacts.
Abstract: This paper presents a novel methodology for Maximum Power Point Tracking (MPPT) of a grid-connected 20 kW Photovoltaic (PV) system using neuro-fuzzy network. The proposed method predicts the reference PV voltage guarantying optimal power transfer between the PV generator and the main utility grid. The neuro-fuzzy network is composed of a fuzzy rule-based classifier and three Radial Basis Function Neural Networks (RBFNN). Inputs of the network (irradiance and temperature) are classified before they are fed into the appropriated RBFNN for either training or estimation process while the output is the reference voltage. The main advantage of the proposed methodology, comparing to a conventional single neural network-based approach, is the distinct generalization ability regarding to the nonlinear and dynamic behavior of a PV generator. In fact, the neuro-fuzzy network is a neural network based multi-model machine learning that defines a set of local models emulating the complex and non-linear behavior of a PV generator under a wide range of operating conditions. Simulation results under several rapid irradiance variations proved that the proposed MPPT method fulfilled the highest efficiency comparing to a conventional single neural network.
Abstract: The need of high frame-rate imaging has been triggered by the new applications of ultrasound imaging to transient elastography and real-time 3D ultrasound. Using plane wave excitation (PWE) is one of the methods to achieve very high frame-rate imaging since an image can be formed with a single insonification. However, due to the lack of transmit focusing, the image quality with PWE is lower compared with those using conventional focused transmission. To solve this problem, we propose a filter-retrieved transmit focusing (FRF) technique combined with cross-correlation weighting (FRF+CC weighting) for high frame-rate imaging with PWE. A restrospective focusing filter is designed to simultaneously minimize the predefined sidelobe energy associated with single PWE and the filter energy related to the signal-to-noise-ratio (SNR). This filter attempts to maintain the mainlobe signals and to reduce the sidelobe ones, which gives similar mainlobe signals and different sidelobes between the original PWE and the FRF baseband data. Normalized cross-correlation coefficient at zero lag is calculated to quantify the degree of similarity at each imaging point and used as a weighting matrix to the FRF baseband data to further suppress sidelobes, thus improving the filter-retrieved focusing quality.
Abstract: This paper studies a vital issue in wireless
communications, which is the transmission of images over Wireless
Personal Area Networks (WPANs) through the Bluetooth network. It
presents a simple method to improve the efficiency of error control
code of old Bluetooth versions over mobile WPANs through
Interleaved Error Control Code (IECC) technique. The encoded
packets are interleaved by simple block interleaver. Also, the paper
presents a chaotic interleaving scheme as a tool against bursts of
errors which depends on the chaotic Baker map. Also, the paper
proposes using the chaotic interleaver instead of traditional block
interleaver with Forward Error Control (FEC) scheme. A comparison
study between the proposed and standard techniques for image
transmission over a correlated fading channel is presented.
Simulation results reveal the superiority of the proposed chaotic
interleaving scheme to other schemes. Also, the superiority of FEC
with proposed chaotic interleaver to the conventional interleavers
with enhancing the security level with chaotic interleaving packetby-
packet basis.
Abstract: Sunflower stalks were analysed for chemical
compositions: pentosan 15.84%, holocellulose 70.69%,
alphacellulose 45.74%, glucose 27.10% and xylose 7.69% based on
dry weight of 100-g raw material. The most optimum condition for
steam explosion pretreatment was as follows. Sunflower stalks were
cut into small pieces and soaked in 0.02 M H2SO4 for overnight.
After that, they were steam exploded at 207 C and 21 kg/cm2 for 3
minutes to fractionate cellulose, hemicellulose and lignin. The
resulting hydrolysate, containing hemicellulose, and cellulose pulp
contained xylose sugar at 2.53% and 7.00%, respectively.The pulp
was further subjected to enzymatic saccharification at 50 C, pH 4.8 citrate buffer) with pulp/buffer 6% (w/w)and Celluclast 1.5L/pulp
2.67% (w/w) to obtain single glucose with maximum yield 11.97%.
After fixed-bed fermentation under optimum condition using
conventional yeast mixtures to produce bioethanol, it indicated
maximum ethanol yield of 0.028 g/100 g sunflower stalk.