Abstract: Misalignment and unbalance are the major concerns
in rotating machinery. When the power supply to any rotating system
is cutoff, the system begins to lose the momentum gained during
sustained operation and finally comes to rest. The exact time period
from when the power is cutoff until the rotor comes to rest is called
Coast Down Time. The CDTs for different shaft cutoff speeds were
recorded at various misalignment and unbalance conditions. The
CDT reduction percentages were calculated for each fault and there
is a specific correlation between the CDT reduction percentage and
the severity of the fault. In this paper, radial basis network, a new
generation of artificial neural networks, has been successfully
incorporated for the prediction of CDT for misalignment and
unbalance conditions. Radial basis network has been found to be
successful in the prediction of CDT for mechanical faults in rotating
machinery.
Abstract: Successful public-private-partnership (PPP)
implementation can not be achieved without the active participation of
private sector companies. This paper examines the decision-making of
private sector companies in public works delivered by the PPP model
on the basis of social responsibility theory. It proposes that private
sector companies should indentify objectives of entering into PPP
projects, and shoulder relevant social responsibilities, while a
minimum return should also be guaranteed in their favor, so as to
compensate for their assumed risk and support them to take on
responsibilities in the future. The paper also gives a calculation
regarding the appropriate scale and reasonable degree of private sector
involvement in PPP projects through the cost-benefit analysis in a
specific case study, with the purpose to guide the private sector
companies to create a cooperation environment resembling
“symbiosis" and facilitate the smooth implementation of public works
delivered by the PPP model.
Abstract: This paper describes the design of a voltage based maximum power point tracker (MPPT) for photovoltaic (PV) applications. Of the various MPPT methods, the voltage based method is considered to be the simplest and cost effective. The major disadvantage of this method is that the PV array is disconnected from the load for the sampling of its open circuit voltage, which inevitably results in power loss. Another disadvantage, in case of rapid irradiance variation, is that if the duration between two successive samplings, called the sampling period, is too long there is a considerable loss. This is because the output voltage of the PV array follows the unchanged reference during one sampling period. Once a maximum power point (MPP) is tracked and a change in irradiation occurs between two successive samplings, then the new MPP is not tracked until the next sampling of the PV array voltage. This paper proposes an MPPT circuit in which the sampling interval of the PV array voltage, and the sampling period have been shortened. The sample and hold circuit has also been simplified. The proposed circuit does not utilize a microcontroller or a digital signal processor and is thus suitable for low cost and low power applications.
Abstract: In this paper we present a novel approach for wavelet compression of electrocardiogram (ECG) signals based on the set partitioning in hierarchical trees (SPIHT) coding algorithm. SPIHT algorithm has achieved prominent success in image compression. Here we use a modified version of SPIHT for one dimensional signals. We applied wavelet transform with SPIHT coding algorithm on different records of MIT-BIH database. The results show the high efficiency of this method in ECG compression.
Abstract: Due to the call of global warming effects, city planners aim at actions for reducing carbon emission. One of the approaches is to promote the usage of public transportation system toward the transit-oriented-development. For example, rapid transit system in Taipei city and Kaohsiung city are opening. However, until November 2008 the average daily patronage counted only 113,774 passengers at Kaohsiung MRT systems, much less than which was expected. Now the crucial questions: how the public transport competes with private transport? And more importantly, what factors would enhance the use of public transport? To give the answers to those questions, our study first applied regression to analyze the factors attracting people to use public transport around cities in the world. It is shown in our study that the number of MRT stations, city population, cost of living, transit fare, density, gasoline price, and scooter being a major mode of transport are the major factors. Subsequently, our study identified successful and unsuccessful cities in regard of the public transport usage based on the diagnosis of regression residuals. Finally, by comparing transportation strategies adopted by those successful cities, our conclusion stated that Kaohsiung City could apply strategies such as increasing parking fees, reducing parking spaces in downtown area, and reducing transfer time by providing more bus services and public bikes to promote the usage of public transport.
Abstract: Benefits to the organisation are just as important as technical ability when it comes to software success. The challenge is to provide industry with professionals who understand this. In other words: How to teach computer engineering students to look beyond technology, and at the benefits of software to organizations? This paper reports on the conceptual design of a section of the computer networks module aimed to sensitize the students to the organisational context.
Checkland focuses on different worldviews represented by various role players in the organisation. He developed the Soft Systems Methodology that guides purposeful action in organisations, while incorporating different worldviews in the modeling process. If we can sensitize students to these methods, they are likely to appreciate the wider context of application of system software. This paper will provide literature on these concepts as well as detail on how the students will be guided to adopt these concepts.
Abstract: The aim of this paper is to examine factors related to system environment (namely, system quality and vendor support) that influences ERP implementation success in Iranian companies. Implementation success is identified using user satisfaction and organizational impact perspective. The study adopts the survey questionnaire approach to collect empirical data. The questionnaire was distributed to ERP users and a total of 384 responses were used for analysis. The results illustrated that both system quality and vendor support have significant effect on ERP implementation success. This implies that companies must ensure they source for the best available system and a vendor that is dependable, reliable and trustworthy.
Abstract: This paper includes two novel techniques for skew
estimation of binary document images. These algorithms are based on
connected component analysis and Hough transform. Both these
methods focus on reducing the amount of input data provided to
Hough transform. In the first method, referred as word centroid
approach, the centroids of selected words are used for skew detection.
In the second method, referred as dilate & thin approach, the selected
characters are blocked and dilated to get word blocks and later
thinning is applied. The final image fed to Hough transform has the
thinned coordinates of word blocks in the image. The methods have
been successful in reducing the computational complexity of Hough
transform based skew estimation algorithms. Promising experimental
results are also provided to prove the effectiveness of the proposed
methods.
Abstract: Asthma is a condition that causing chronic health problems in children. In addition to basic therapy against disease, we must try to reduce the impact of chronic health problems and also optimize their medical aspect of growth and development. A boy with mild asthma attack frequent episode did not showed any improvement with medical treatment and his asthma control test was 11. From radiologic examination he got hyperaerated lung and billateral sinusitis maxillaris; skin test results were house dust, food and pet allergy; an overweight body; bad school grades; psychological and environmental problem. We followed and evaluated this boy in 6 months, treated holistically. Even we could not do much on environmental but no more psychological and school problems, his on a good bodyweight and his asthma control test was 22. A case of a child with mild asthma attack frequent episode was reported. Asthma clinical course show no significant improvement when other predisposing factor is not well-controlled and a child’s growth and development may be affected. Improving condition of the patient can be created with the help of loving and caring way of nurturing from the parents and supportive peer group. Therefore, continuous and consistent monitoring is required because prognosis of asthma is generally good when regularly and properly controlled.
Abstract: The scattering effect of light in fog improves the
difficulty in visibility thus introducing disturbances in transport
facilities in urban or industrial areas causing fatal accidents or public
harassments, therefore, developing an enhanced fog vision system
with radio wave to improvise the way outs of these severe problems
is really a big challenge for researchers. Series of experimental
studies already been done and more are in progress to know the
weather effect on radio frequencies for different ranges. According to
Rayleigh scattering Law, the propagating wavelength should be
greater than the diameter of the particle present in the penetrating
medium. Direct wave RF signal thus have high chance of failure to
work in such weather for detection of any object. Therefore an
extensive study was required to find suitable region in the RF band
that can help us in detecting objects with proper shape. This paper
produces some results on object detection using 912 MHz band with
successful detection of the persistence of any object coming under the
trajectory of a vehicle navigating in indoor and outdoor environment.
The developed images are finally transformed to video signal to
enable continuous monitoring.
Abstract: The MFCAV Riemann solver is practically used in many Lagrangian or ALE methods due to its merit of sharp shock profiles and rarefaction corners, though very often with numerical oscillations. By viewing it as a modification of the WWAM Riemann solver, we apply the MFCAV Riemann solver to the Lagrangian method recently developed by Maire. P. H et. al.. The numerical experiments show that the application is successful in that the shock profiles and rarefaction corners are sharpened compared with results obtained using other Riemann solvers. Though there are still numerical oscillations, they are within the range of the MFCAV applied in onther Lagrangian methods.
Abstract: The aim of this study was to evaluate the sensitivity
of a range of EEG indices to time-on-task effects and to a workload
manipulation (cueing), during performance of a resource-limited
vigilance task. Effects of task period and cueing on performance and
subjective state response were consistent with previous vigilance
studies and with resource theory. Two EEG indices – the Task Load
Index (TLI) and global lower frequency (LF) alpha power – showed
effects of task period and cueing similar to those seen with correct
detections. Across four successive task periods, the TLI declined and
LF alpha power increased. Cueing increased TLI and decreased LF
alpha. Other indices – the Engagement Index (EI), frontal theta and
upper frequency (UF) alpha failed to show these effects. However, EI
and frontal theta were sensitive to interactive effects of task period
and cueing, which may correspond to a stronger anxiety response to
the uncued task.
Abstract: Among the most fundamental prerequisites for the successful development of electronic Government Services (e- Government) is Citizen Acceptance. Based on the UTAUT model, the paper describes a hypothetical framework that integrates the unique features of E- government to improve our understanding of the acceptance and usage of e-Government Saudi Arabia. The proposed model, based on UTAUT, includes the characteristics of Egovernment, consideration and inclusion of trust, privacy, and Saudi culture and context.
Abstract: This paper proposes an efficient method to classify
inverse synthetic aperture (ISAR) images. Because ISAR images can
be translated and rotated in the 2-dimensional image place, invariance
to the two factors is indispensable for successful classification. The
proposed method achieves invariance to translation and rotation of
ISAR images using a combination of two-dimensional Fourier
transform, polar mapping and correlation-based alignment of the
image. Classification is conducted using a simple matching score
classifier. In simulations using the real ISAR images of five scaled
models measured in a compact range, the proposed method yields
classification ratios higher than 97 %.
Abstract: At present time, competition, unpredictable fluctuations have made communication engineering education in the global sphere really difficult. Confront with new situation in the engineering education sector. Communication engineering education has to be reformed and ready to use more advanced technologies. We realized that one of the general problems of student`s education is that after graduating from their universities, they are not prepared to face the real life challenges and full skilled to work in industry. They are prepared only to think like engineers and professionals but they also need to possess some others non-technical skills. In today-s environment, technical competence alone is not sufficient for career success. Employers want employees (graduate engineers) who have good oral and written communication (soft) skills. It does require for team work, business awareness, organization, management skills, responsibility, initiative, problem solving and IT competency. This proposed curriculum brings interactive, creative, interesting, effective learning methods, which includes online education, virtual labs, practical work, problem-based learning (PBL), and lectures given by industry experts. Giving short assignments, presentations, reports, research papers and projects students can significantly improve their non-technical skills. Also, we noticed the importance of using ICT technologies in engineering education which used by students and teachers, and included that into proposed teaching and learning methods. We added collaborative learning between students through team work which builds theirs skills besides course materials. The prospective on this research that we intent to update communication engineering curriculum in order to get fully constructed engineer students to ready for real industry work.
Abstract: Renewable energy resources are inexhaustible, clean as compared with conventional resources. Also, it is used to supply regions with no grid, no telephone lines, and often with difficult accessibility by common transport. Satellite earth stations which located in remote areas are the most important application of renewable energy. Neural control is a branch of the general field of intelligent control, which is based on the concept of artificial intelligence. This paper presents the mathematical modeling of satellite earth station power system which is required for simulating the system.Aswan is selected to be the site under consideration because it is a rich region with solar energy. The complete power system is simulated using MATLAB–SIMULINK.An artificial neural network (ANN) based model has been developed for the optimum operation of earth station power system. An ANN is trained using a back propagation with Levenberg–Marquardt algorithm. The best validation performance is obtained for minimum mean square error. The regression between the network output and the corresponding target is equal to 96% which means a high accuracy. Neural network controller architecture gives satisfactory results with small number of neurons, hence better in terms of memory and time are required for NNC implementation. The results indicate that the proposed control unit using ANN can be successfully used for controlling the satellite earth station power system.
Abstract: Proprietary sensor network systems are typically expensive, rigid and difficult to incorporate technologies from other vendors. When using competing and incompatible technologies, a non-proprietary system is complex to create because it requires significant technical expertise and effort, which can be more expensive than a proprietary product. This paper presents the Sensor Abstraction Layer (SAL) that provides middleware architectures with a consistent and uniform view of heterogeneous sensor networks, regardless of the technologies involved. SAL abstracts and hides the hardware disparities and specificities related to accessing, controlling, probing and piloting heterogeneous sensors. SAL is a single software library containing a stable hardware-independent interface with consistent access and control functions to remotely manage the network. The end-user has near-real-time access to the collected data via the network, which results in a cost-effective, flexible and simplified system suitable for novice users. SAL has been used for successfully implementing several low-cost sensor network systems.
Abstract: This paper proposes the novel model order
formulation scheme to design a discrete PID controller for higher
order linear time invariant discrete systems. Modified PSO (MPSO)
based model order formulation technique has used to obtain the
successful formulated second order system. PID controller is tuned to
meet the desired performance specification by using pole-zero
cancellation and proposed design procedures. Proposed PID
controller is attached with both higher order system and formulated
second order system. System specifications are tabulated and closed
loop response is observed for stabilization process. The proposed
method is illustrated through numerical examples from literature.
Abstract: this article proposed a methodology for computer
numerical control (CNC) machine scoring. The case study company
is a manufacturer of hard disk drive parts in Thailand. In this
company, sample of parts manufactured from CNC machine are
usually taken randomly for quality inspection. These inspection data
were used to make a decision to shut down the machine if it has
tendency to produce parts that are out of specification. Large amount
of data are produced in this process and data mining could be very
useful technique in analyzing them. In this research, data mining
techniques were used to construct a machine scoring model called
'machine priority assessment model (MPAM)'. This model helps to
ensure that the machine with higher risk of producing defective parts
be inspected before those with lower risk. If the defective prone
machine is identified sooner, defective part and rework could be
reduced hence improving the overall productivity. The results
showed that the proposed method can be successfully implemented
and approximately 351,000 baht of opportunity cost could have
saved in the case study company.
Abstract: The selection of appropriate requirements for product
releases can make a big difference in a product success. The selection
of requirements is done by different requirements prioritization
techniques. These techniques are based on pre-defined and
systematic steps to calculate the requirements relative weight.
Prioritization is complicated by new development settings, shifting
from traditional co-located development to geographically distributed
development. Stakeholders, connected to a project, are distributed all
over the world. These geographically distributions of stakeholders
make it hard to prioritize requirements as each stakeholder have their
own perception and expectations of the requirements in a software
project. This paper discusses limitations of the Analytical Hierarchy
Process with respect to geographically distributed stakeholders-
(GDS) prioritization of requirements. This paper also provides a
solution, in the form of a modified AHP, in order to prioritize
requirements for GDS. We will conduct two experiments in this
paper and will analyze the results in order to discuss AHP limitations
with respect to GDS. The modified AHP variant is also validated in
this paper.