Abstract: This paper presents the advantages of fuzzy control use in technological processes control. The paper presents a real application of the Linguistic Fuzzy-Logic Control, developed at the University of Ostrava for the control of physical models in the Intelligent Systems Laboratory. The paper presents an example of a sensitive non-linear model, such as a magnetic levitation model and obtained results which show how modern information technologies can help to solve actual technical problems. A special method based on the LFLC controller with partial components is presented in this paper followed by the method of automatic context change, which is very helpful to achieve more accurate control results. The main advantage of the used system is its robustness in changing conditions demonstrated by comparing with conventional PID controller. This technology and real models are also used as a background for problem-oriented teaching, realized at the department for master students and their collaborative as well as individual final projects.
Abstract: The Greater Athens Area (GAA) faces photochemical
and particulate pollution episodes as a result of the combined effects
of local pollutant emissions, regional pollution transport, synoptic
circulation and topographic characteristics. The area has undergone
significant changes since the Athens 2004 Olympic Games because
of large scale infrastructure works that lead to the shift of population
to areas previously characterized as rural, the increase of the traffic
fleet and the operation of highways. However, few recent modelling
studies have been performed due to the lack of an accurate, updated
emission inventory. The photochemical modelling system
MM5/CAMx was applied in order to study the photochemical and
particulate pollution characteristics above the GAA for two distinct
ten-day periods in the summer of 2006 and 2010, where air pollution
episodes occurred. A new updated emission inventory was used
based on official data. Comparison of modeled results with
measurements revealed the importance and accuracy of the new
Athens emission inventory as compared to previous modeling
studies. The model managed to reproduce the local meteorological
conditions, the daily ozone and particulates fluctuations at different
locations across the GAA. Higher ozone levels were found at
suburban and rural areas as well as over the sea at the south of the
basin. Concerning PM10, high concentrations were computed at the
city centre and the southeastern suburbs in agreement with measured
data. Source apportionment analysis showed that different sources
contribute to the ozone levels, the local sources (traffic, port
activities) affecting its formation.
Abstract: This paper integrates Octagon and Square Search
pattern (OCTSS) motion estimation algorithm into H.264/AVC
(Advanced Video Coding) video codec in Adaptive Group of Pictures
(AGOP) mode. AGOP structure is computed based on scene change
in the video sequence. Octagon and square search pattern block-based
motion estimation method is implemented in inter-prediction process
of H.264/AVC. Both these methods reduce bit rate and computational
complexity while maintaining the quality of the video sequence
respectively. Experiments are conducted for different types of video
sequence. The results substantially proved that the bit rate,
computation time and PSNR gain achieved by the proposed method
is better than the existing H.264/AVC with fixed GOP and AGOP.
With a marginal gain in quality of 0.28dB and average gain in bitrate
of 132.87kbps, the proposed method reduces the average computation
time by 27.31 minutes when compared to the existing state-of-art
H.264/AVC video codec.
Abstract: We consider the problem of stabilization of an unstable
heat equation in a 2-D, 3-D and generally n-D domain by deriving a
generalized backstepping boundary control design methodology. To
stabilize the systems, we design boundary backstepping controllers
inspired by the 1-D unstable heat equation stabilization procedure.
We assume that one side of the boundary is hinged and the other
side is controlled for each direction of the domain. Thus, controllers
act on two boundaries for 2-D domain, three boundaries for 3-D
domain and ”n” boundaries for n-D domain. The main idea of the
design is to derive ”n” controllers for each of the dimensions by
using ”n” kernel functions. Thus, we obtain ”n” controllers for the
”n” dimensional case. We use a transformation to change the system
into an exponentially stable ”n” dimensional heat equation. The
transformation used in this paper is a generalized Volterra/Fredholm
type with ”n” kernel functions for n-D domain instead of the one
kernel function of 1-D design.
Abstract: The use of information technology in education have
changed not only the learners learning style but also the way they
taught, where nowadays learners are connected with diversity of
information sources with means of knowledge available everywhere.
The advantage of network wireless technologies and mobility
technologies used in the education and learning processes lead to
mobile learning as a new model of learning technology. Currently,
most of mobile learning applications are developed for the formal
education and learning environment. Despite the long history and
large amount of research on mobile learning and instruction design
model still there is a need of well-defined process in designing
mobile learning applications. Based on this situation, this paper
emphasizes on identifying instruction design phase’s considerations
and influencing factors in developing mobile learning application.
This set of instruction design steps includes analysis, design,
development, implementation, evaluation and continuous has been
built from a literature study, with focus on standards for learning,
mobile application software quality and guidelines. The effort is part
of an Omani-funded research project investigating the development,
adoption and dissemination of mobile learning in Oman.
Abstract: The advancements in technology allow the
development of a new system that can continuously measure surface
soil erosion. Continuous soil erosion measurements are required in
order to comprehend the erosional processes and propose effective
and efficient conservation measures to mitigate surface erosion.
Mitigating soil erosion, especially in Mediterranean countries such as
Greece, is essential in order to maintain environmental and
agricultural sustainability. In this paper, we present the Automated
Soil Erosion Monitoring System (ASEMS) that measures surface soil
erosion along with other factors that impact erosional process.
Specifically, this system measures ground level changes (surface soil
erosion), rainfall, air temperature, soil temperature, and soil moisture.
Another important innovation is that the data will be collected by
remote communication. In addition, stakeholder’s awareness is a key
factor to help reduce any environmental problem. The different
dissemination activities that were utilized are described. The overall
outcomes were the development of a new innovative system that can
measure erosion very accurately. These data from the system help
study the process of erosion and find the best possible methods to
reduce erosion. The dissemination activities enhance the stakeholders
and public's awareness on surface soil erosion problems and will lead
to the adoption of more effective soil erosion conservation practices
in Greece.
Abstract: The development of composite materials and the
related design and manufacturing technologies is one of the most
important advances in the history of materials. Composites are
multifunctional materials having unprecedented mechanical and
physical properties that can be tailored to meet the requirements of a
particular application. Some composites also exhibit great resistance
to high-temperature corrosion, oxidation, and wear. Polymers are
widely used indoors and outdoors, therefore they are exposed to a
chemical environment which may include atmospheric oxygen, acidic
fumes, acidic rain, moisture heat and thermal shock, ultra-violet light,
high energy radiation, etc. Different polymers are affected differently
by these factors even though the amorphous polymers are more
sensitive. Ageing is also important and it is defined as the process of
deterioration of engineering materials resulting from the combined
effects of atmospheric radiation, heat, oxygen, water, microorganisms
and other atmospheric factors.
Abstract: Rapid prototyping is a new group of manufacturing
processes, which allows fabrication of physical of any complexity
using a layer by layer deposition technique directly from a computer
system. The rapid prototyping process greatly reduces the time and
cost necessary to bring a new product to market. The prototypes
made by these systems are used in a range of industrial application
including design evaluation, verification, testing, and as patterns for
casting processes. These processes employ a variety of materials and
mechanisms to build up the layers to build the part. The present work
was to build a FDM prototyping machine that could control the X-Y
motion and material deposition, to generate two-dimensional and
three-dimensional complex shapes. This study focused on the
deposition of wax material. This work was to find out the properties
of the wax materials used in this work in order to enable better
control of the FDM process. This study will look at the integration of
a computer controlled electro-mechanical system with the traditional
FDM additive prototyping process. The characteristics of the wax
were also analysed in order to optimise the model production process.
These included wax phase change temperature, wax viscosity and
wax droplet shape during processing.
Abstract: In recent years, the power system has been changed
and a flexible power pricing system such as demand response has been
sought in Japan. The demand response system works simply in the
household sector and the owner as the decision-maker, can benefit
from power saving. On the other hand, the execution of demand
response in the office building is more complex than in the household
because various people such as owners, building administrators and
occupants are involved in the decision-making process. While the
owners benefit from demand saving, the occupants are exposed to
restricted benefits of a demand-saved environment. One of the reasons
is that building systems are usually under centralized management and
each occupant cannot choose freely whether to participate in demand
response or not. In addition, it is unclear whether incentives give
occupants the motivation to participate. However, the recent
development of IT and building systems enables the personalized
control of the office environment where each occupant can control the
lighting level or temperature individually. Therefore, it can be possible
to have a system which each occupant can make a decision of whether
or not to participate in demand response in the office building. This study investigates personal responses to demand response
requests, under the condition where each occupant can adjust their
brightness individually in their workspace. Once workers participate
in the demand response, their desk-lights are automatically turned off.
The participation rates in the demand response events are compared
among four groups, which are divided by different motivation, the
presence, or absence of incentives and the method of participation. The
result shows that there are significant differences of participation rates
in demand response event between four groups. The method of
participation has a large effect on the participation rate. The “Opt-out”
groups where the occupants are automatically enrolled in a demand
response event if they do not express non-participation have the
highest participation rate in the four groups. Incentives also have an
effect on the participation rate. This study also reports on the impact of low illumination office
environment on the occupants, such as stress or fatigue. The
electrocardiogram and the questionnaire are used to investigate the
autonomic nervous activity and subjective fatigue symptoms of the
occupants. There is no big difference between dim workspace during
demand response event and bright workspace in autonomic nervous
activity and fatigue.
Abstract: This paper presents the influence of the vertical
seismic component on the non-linear dynamics analysis of three
different structures. The subject structures were analyzed and
designed according to recent codes. This paper considers three types
of buildings: 5-, 10-, and 15-story buildings. The non-linear
dynamics analysis of the structures with assuming elastic-perfectlyplastic
behavior was performed using RAM PERFORM-3D software;
the horizontal component was taken into consideration with and
without the incorporation of the corresponding vertical component.
Dynamic responses obtained for the horizontal component acting
alone were compared with those obtained from the simultaneous
application of both seismic components. The results show that the
effect of the vertical component of ground motion may increase the
axial load significantly in the interior columns and, consequently, the
stories. The plastic mechanisms would be changed. The P-Delta
effect is expected to increase. The punching base plate shear of the
columns should be considered. Moreover, the vertical component
increases the input energy when the structures exhibit inelastic
behavior and are taller.
Abstract: An integrated modeling approach was used in this study for energy planning and climate change mitigation assessment. The main objective of this study was to develop various green-house gas (GHG) mitigations scenarios in the energy demand and supply sectors for the state of Florida. The Long range energy alternative planning (LEAP) model was used in this study to examine the energy alternative and GHG emissions reduction scenarios for short and long term (2010-2050). One of the energy analysis and GHG mitigation scenarios was developed by taking into account the available renewable energy resources potential for power generation in the state of Florida. This will help to compare and analyze the GHG reduction measure against “Business As Usual” and ‘State of Florida Policy” scenarios. Two master scenarios: “Electrification” and “Energy efficiency and Lifestyle” were developed through combination of various mitigation scenarios: technological changes and energy efficiency and conservation. The results show a net reduction of the energy demand and GHG emissions by adopting these two energy scenarios compared to the business as usual.
Abstract: This paper tries to answer to the questions whether or
not trade openness causes economic growth and trade policy changes
are good for Turkey as a developing country in global economy
before and after 1980. We employ Johansen co-integration and
Granger causality tests with error correction modeling based on
vector autoregressive. Using WDI data from the pre-1980 and the
post-1980, we find that trade openness and economic growth are cointegrated
in the second term only. Also the results suggest a lack of
long-run causality between our two variables. These findings may
imply that trade policy of Turkey should concentrate more on extra
complementary economic reforms.
Abstract: Our sowing date experiment took place in the
Demonstration Garden of Institution of Plant Sciences, Centre for
Agricultural Sciences of University of Debrecen, in 2012-2014. The
paper contains data of test year 2014. Our purpose, besides several
other examinations, was to observe how sowing date influences the
leaf area index and the activity of photosynthesis of maize hybrids,
and how those factors affect fruiting. In the experiment we monitored
the change of the leaf area index and the photosynthesis of hybrids
with four different growing seasons. The results obtained confirm
that not only the environmental and agricultural factors in the
growing season have effect on the yield, but also other factors like
the leaf area index and the photosynthesis are determinative
parameters, and all those factors together, modifying the effects of
each other, develop average yields.
Abstract: In this study, it has been studied to determine the
relationship between business performance and strategic flexibility,
which is defined to be the strategic choice that provides the ability of
rapidly responding the changes of the dynamic environment of the
companies, for having competitive advantages. In this context a field
study has been conducted over 56 companies, which are active in
informatics and electronics sectors in TEKNOKENT. As a result of
the study it has been determined that; strategic flexibility has an
effect on business performance and there is a positive and
statistically significant relationship between strategic flexibility and
business performance.
Abstract: The influence of Islam on arts can be found primarily
in calligraphy, arabesque designs and architecture. Also, geometric
designs were used quite extensively. Muslim craftsmen produced
stunning designs based on simple geometric principles and traditional
motifs which were used to decorate many surfaces. The idea of
interlacing simple rectilinear lines to form the patterns impressed
Arabs. Nomads of Persia, Turks and Mongols were equally
impressed with the designs so they begin to use them in their homes
in carpet weaving. Islamic designs, motifs and colours which were
used became common place and served to influence people’s tastes.
Modern life style and contemporary products have changed the style
of people’s daily lives, however, people still long for the nomadic
way of life. This is clearly reflected in people’s homes. In a great
many Muslim homes, Islamic decorative motifs can be seen along
with traditional ‘Bedouin’ style furnishing, especially in homes of the
Arabian Peninsula.
Abstract: Si-Ge solid solutions (bulk poly- and mono-crystalline
samples, thin films) are characterized by high perspectives for
application in semiconductor devices, in particular, optoelectronics
and microelectronics. From this point of view, complex studying of
structural state of the defects and structural-sensitive physical
properties of Si-Ge solid solutions depending on the contents of Si
and Ge components is very important. Present work deals with the
investigations of microstructure, microhardness, internal friction and
shear modulus of Si1-xGex(x≤0,02) bulk monocrystals conducted at
room temperature. Si-Ge bulk crystals were obtained by Czochralski
method in [111] crystallographic direction. Investigated
monocrystalline Si-Ge samples are characterized by p-type
conductivity and carriers’ concentration 5.1014-1.1015cm-3.
Microhardness was studied on Dynamic Ultra Micro hardness Tester
DUH-201S with Berkovich indenter. Investigate samples are characterized with 0,5x0,5x(10-15)mm3
sizes, oriented along [111] direction at torsion oscillations ≈1Hz,
multistage changing of internal friction and shear modulus has been
revealed in an interval of strain amplitude of 10-5-5.10-3. Critical
values of strain amplitude have been determined at which hysteretic
changes of inelastic characteristics and microplasticity are observed. The critical strain amplitude and elasticity limit values are also
determined. Dynamic mechanical characteristics decreasing trend is
shown with increasing Ge content in Si-Ge solid solutions. Observed
changes are discussed from the point of view of interaction of various
dislocations with point defects and their complexes in a real structure
of Si-Ge solid solutions.
Abstract: The need to merge software artifacts seems inherent
to modern software development. Distribution of development over
several teams and breaking tasks into smaller, more manageable
pieces are an effective means to deal with the kind of complexity. In
each case, the separately developed artifacts need to be assembled as
efficiently as possible into a consistent whole in which the parts still
function as described. In addition, earlier changes are introduced into
the life cycle and easier is their management by designers.
Interaction-based specifications such as UML sequence diagrams
have been found effective in this regard. As a result, sequence
diagrams can be used not only for capturing system behaviors but
also for merging changes in order to create a new version. The
objective of this paper is to suggest a new approach to deal with the
problem of software merging at the level of sequence diagrams by
using the concept of dependence analysis that captures, formally, all
mapping, and differences between elements of sequence diagrams
and serves as a key concept to create a new version of sequence
diagram.
Abstract: Heart is the most important part in the body of living
organisms. It affects and is affected by any factor in the body.
Therefore, it is a good detector for all conditions in the body. Heart
signal is a non-stationary signal; thus, it is utmost important to study
the variability of heart signal. The Heart Rate Variability (HRV) has
attracted considerable attention in psychology, medicine and has
become important dependent measure in psychophysiology and
behavioral medicine. The standards of measurements, physiological
interpretation and clinical use for HRV that are most often used were
described in many researcher papers, however, remain complex
issues are fraught with pitfalls. This paper presents one of the nonlinear
techniques to analyze HRV. It discusses many points like, what
Poincaré plot is and how Poincaré plot works; also, Poincaré plot's
merits especially in HRV. Besides, it discusses the limitation of
Poincaré cause of standard deviation SD1, SD2 and how to overcome
this limitation by using complex correlation measure (CCM). The
CCM is most sensitive to changes in temporal structure of the
Poincaré plot as compared toSD1 and SD2.
Abstract: This paper aims to determine Fundamental Natural
Frequency (FNF) of a structural composite floor system known as
Chromite. To achieve this purpose, FNFs of studied panels are
determined by development of Finite Element Models (FEMs) in
ABAQUS program. American Institute of Steel Construction (AISC)
code in Steel Design Guide Series 11 presents a fundamental formula
to calculate FNF of a steel framed floor system. This formula has
been used to verify results of the FEMs. The variability in the FNF of
the studied system under various parameters such as dimensions of
floor, boundary conditions, rigidity of main and secondary beams
around the floor, thickness of concrete slab, height of composite
joists, distance between composite joists, thickness of top and bottom
flanges of the open web steel joists, and adding tie beam
perpendicular on the composite joists, is determined. The results
show that changing in dimensions of the system, its boundary
conditions, rigidity of main beam, and also adding tie beam,
significant changes the FNF of the system up to 452.9%, 50.8%, -
52.2%, %52.6%, respectively. In addition, increasing thickness of
concrete slab increases the FNF of the system up to 10.8%.
Furthermore, the results demonstrate that variation in rigidity of
secondary beam, height of composite joist, and distance between
composite joists, and thickness of top and bottom flanges of open
web steel joists insignificant changes the FNF of the studied system
up to -0.02%, -3%, -6.1%, and 0.96%, respectively. Finally, the
results of this study help designer predict occurrence of resonance,
comfortableness, and design criteria of the studied system.
Abstract: The authors conducted a study for the sample size of
75 HR managers from an Indian IT company through systematic
sampling method. This study identifies that the female employees are
facing lesser conflict than the male employees against their managers
within the organization. There is a positive correlation between
gender and conflict management with the superior towards the work.
There is a significant variance between age and response towards
appraisal system, succession planning and employee engagement.
The education qualification plays a major role in determining the
compensation factor for the employees working in the organization.
The study determines the impact of demographic profile on strategic
HRM practices and its challenges faced by HR managers in IT firm,
India.