Abstract: The purpose of the present work was to study the
production and process parameters optimization for the synthesis of
cellulase from Trichoderma viride in solid state fermentation (SSF)
using an agricultural wheat straw as substrates; as fungal conversion
of lignocellulosic biomass for cellulase production is one among the
major increasing demand for various biotechnological applications.
An optimization of process parameters is a necessary step to get
higher yield of product. Several kinetic parameters like pretreatment,
extraction solvent, substrate concentration, initial moisture content,
pH, incubation temperature and inoculum size were optimized for
enhanced production of third most demanded industrially important
cellulase. The maximum cellulase enzyme activity 398.10±2.43
μM/mL/min was achieved when proximally analyzed lignocellulosic
substrate wheat straw inocubated at 2% HCl as pretreatment tool
along with distilled water as extraction solvent, 3% substrate
concentration 40% moisture content with optimum pH 5.5 at 45°C
incubation temperature and 10% inoculum size.
Abstract: This study aims to determine the level of resistance of Hevea brasiliensis and Paraserianthes falcataria (synonym: Falcataria molucana) against wood rot fungi Pleurotus ostreatus based on Indonesian standard SNI 01.7207-2006 and Japanese standard JIS K 1571-2004. The variables measured were visual appearance and weight loss percentage of wood based on longitudinal and cross section fiber directions of rubber wood and sengon wood. Measurement of oven dry weight loss of wood samples performed after 12 weeks incubation. Replication performed was 10 times at each treatment combination. The results based on SNI 01.7207-2006, weight loss value of H. brasiliensis and P. falcataria wood with fiber direction longitudinal were 23,12 and 22,25% respectively and cross section were 20,77 and 18,76% respectively, and all were classified to resistance class IV (no resistance). The results based on JIS K 1571-2004, weight loss value of both woods with fiber direction cross section were 10,95 and 14,20% respectively.
Abstract: With the advent of new technologies, factors related to
mental health in e-workspaces are taken into consideration more than
ever. Studies have revealed that one of the factors affecting the
productivity of employees in an organization is occupational stress.
Another influential factor is quality of work life which is important in
the improvement of work environment conditions and organizational
efficiency. In order to uncover the quality of work life level and to
investigate the impact of occupational stress on quality of work life
among information technology employees in Iran, a cross-sectional
study design was applied and data were gathered using a
questionnaire validated by a group of experts. The results of the study
showed that information technology staffs have average level of both
occupational stress and quality of work life. Furthermore, it was
found that occupational stress has a negative impact on quality of
work life. In addition, the same results were observed for role
ambiguity, role conflict, role under-load, work-pace, work
repetitiveness and tension toward quality of work life. No significant
relation was found between role overload and quality of work life.
Finally, directions for future research are proposed and discussed.
Abstract: In this paper we are interested in classification problems
with a performance constraint on error probability. In such
problems if the constraint cannot be satisfied, then a rejection option
is introduced. For binary labelled classification, a number of SVM
based methods with rejection option have been proposed over the
past few years. All of these methods use two thresholds on the SVM
output. However, in previous works, we have shown on synthetic data
that using thresholds on the output of the optimal SVM may lead to
poor results for classification tasks with performance constraint. In
this paper a new method for supervised classification with rejection
option is proposed. It consists in two different classifiers jointly
optimized to minimize the rejection probability subject to a given
constraint on error rate. This method uses a new kernel based linear
learning machine that we have recently presented. This learning
machine is characterized by its simplicity and high training speed
which makes the simultaneous optimization of the two classifiers
computationally reasonable. The proposed classification method with
rejection option is compared to a SVM based rejection method
proposed in recent literature. Experiments show the superiority of
the proposed method.
Abstract: the effects of refining and alkaline chemicals on potential of recycling bleached chemical pulp of bagasse were investigated in this study. Recycling was done until three times. Handsheet properties such as, apparent density, light scattering coefficient, tear index, burst index, breaking length, and fold number according to TAPPI standard were measured. Water retention value also was used to considering the treatments during recycling. Refining enhanced the strength of recycled pulp by increasing fiber flexibility and swelling ability, whereas by applying chemical treatment didn't observe any improvement. The morphology of recycled fiber was considered with scanning electron microscopy (SEM).
Abstract: With the popularity of the multi-core and many-core architectures there is a great requirement for software frameworks which can support parallel programming methodologies. In this paper we introduce an Eclipse toolkit, JConqurr which is easy to use and provides robust support for flexible parallel progrmaming. JConqurr is a multi-core and many-core programming toolkit for Java which is capable of providing support for common parallel programming patterns which include task, data, divide and conquer and pipeline parallelism. The toolkit uses an annotation and a directive mechanism to convert the sequential code into parallel code. In addition to that we have proposed a novel mechanism to achieve the parallelism using graphical processing units (GPU). Experiments with common parallelizable algorithms have shown that our toolkit can be easily and efficiently used to convert sequential code to parallel code and significant performance gains can be achieved.
Abstract: The objective of this paper is to investigate a new
approach based on the idea of pictograms for food portion size. This
approach adopts the model of the United States Pharmacopeia- Drug
Information (USP-DI). The representation of each food portion size
composed of three parts: frame, the connotation of dietary portion
sizes and layout. To investigate users- comprehension based on this
approach, two experiments were conducted, included 122 Taiwanese
people, 60 male and 62 female with ages between 16 and 64 (divided
into age groups of 16-30, 31-45 and 46-64). In Experiment 1, the mean
correcting rate of the understanding level of food items is 48.54%
(S.D.= 95.08) and the mean response time 2.89sec (S.D.=2.14). The
difference on the correct rates for different age groups is significant
(P*=0.00
Abstract: In this paper, free vibration analysis of carbon nanotube (CNT) reinforced laminated composite panels is presented. Three types of panels such as flat, concave and convex are considered for study. Numerical simulation is carried out using commercially available finite element analysis software ANSYS. Numerical homogenization is employed to calculate the effective elastic properties of randomly distributed carbon nanotube reinforced composites. To verify the accuracy of the finite element method, comparisons are made with existing results available in the literature for conventional laminated composite panels and good agreements are obtained. The results of the CNT reinforced composite materials are compared with conventional composite materials under different boundary conditions.
Abstract: In this paper, a worm-like micro robot designed for inpipe
application with intelligent active force control (AFC) capability
is modelled and simulated. The motion of the micro robot is based on
an impact drive mechanism (IDM) that is actuated using piezoelectric
device. The trajectory tracking performance of the modelled micro
robot is initially experimented via a conventional proportionalintegral-
derivative (PID) controller in which the dynamic response of
the robot system subjected to different input excitations is
investigated. Subsequently, a robust intelligent method known as
active force control with fuzzy logic (AFCFL) is later incorporated
into the PID scheme to enhance the system performance by
compensating the unwanted disturbances due to the interaction of the
robot with its environment. Results show that the proposed AFCFL
scheme is far superior than the PID control counterpart in terms of
the system-s tracking capability in the wake of the disturbances.
Abstract: In order to achieve effective management, the professional and individual characteristics and qualifications of school principals and their system-oriented perception is very important. Therefore, it is necessary to conduct regular comprehensive studies into the profiles of school principals. The purpose of this study is to determine the perceptions of primary school principals about their working conditions and to present their professional profiles. The questionnaire was distributed to 1475 respondents and 1428 valid questionnaires were evaluated. The results of the research were discussed and compared to other similar studies.Keywordseducation, education management, primary school principal, principals profiles
Abstract: This paper proposes a novel hybrid algorithm for feature selection based on a binary ant colony and SVM. The final subset selection is attained through the elimination of the features that produce noise or, are strictly correlated with other already selected features. Our algorithm can improve classification accuracy with a small and appropriate feature subset. Proposed algorithm is easily implemented and because of use of a simple filter in that, its computational complexity is very low. The performance of the proposed algorithm is evaluated through a real Rotary Cement kiln dataset. The results show that our algorithm outperforms existing algorithms.
Abstract: Aggressive scaling of MOS devices requires use of ultra-thin gate oxides to maintain a reasonable short channel effect and to take the advantage of higher density, high speed, lower cost etc. Such thin oxides give rise to high electric fields, resulting in considerable gate tunneling current through gate oxide in nano regime. Consequently, accurate analysis of gate tunneling current is very important especially in context of low power application. In this paper, a simple and efficient analytical model has been developed for channel and source/drain overlap region gate tunneling current through ultra thin gate oxide n-channel MOSFET with inevitable deep submicron effect (DSME).The results obtained have been verified with simulated and reported experimental results for the purpose of validation. It is shown that the calculated tunnel current is well fitted to the measured one over the entire oxide thickness range. The proposed model is suitable enough to be used in circuit simulator due to its simplicity. It is observed that neglecting deep sub-micron effect may lead to large error in the calculated gate tunneling current. It is found that temperature has almost negligible effect on gate tunneling current. It is also reported that gate tunneling current reduces with the increase of gate oxide thickness. The impact of source/drain overlap length is also assessed on gate tunneling current.
Abstract: The growing health hazardous impact of arsenic (As)
contamination in environment is the impetus of the present
investigation. Application of lactic acid bacteria (LAB) for the
removal of toxic and heavy metals from water has been reported.
This study was performed in order to isolate and characterize the Asresistant
LAB from mud and sludge samples for using as efficient As
uptaking probiotic. Isolation of As-resistant LAB colonies was
performed by spread plate technique using bromocresol purple
impregnated-MRS (BP-MRS) agar media provided with As @ 50
μg/ml. Isolated LAB were employed for probiotic characterization
process, acid and bile tolerance, lactic acid production, antibacterial
activity and antibiotic tolerance assays. After As-resistant and
removal characterizations, the LAB were identified using 16S rDNA
sequencing. A total of 103 isolates were identified as As-resistant
strains of LAB. The survival of 6 strains (As99-1, As100-2, As101-3,
As102-4, As105-7, and As112-9) was found after passing through the
sequential probiotic characterizations. Resistant pattern pronounced
hollow zones at As concentration >2000 μg/ml in As99-1, As100-2,
and As101-3 LAB strains, whereas it was found at ~1000 μg/ml in
rest 3 strains. Among 6 strains, the As uptake efficiency of As102-4
(0.006 μg/h/mg wet weight of cell) was higher (17 – 209%)
compared to remaining LAB. 16S rDNA sequencing data of 3 (As99-
1, As100-2, and As101-3) and 3 (As102-4, As105-7, and As112-9)
LAB strains clearly showed 97 to 99% (340 bp) homology to
Pediococcus dextrinicus and Pediococcus acidilactici, respectively.
Though, there was no correlation between the metal resistant and
removal efficiency of LAB examined but identified elevated As
removing LAB would probably be a potential As uptaking probiotic
agent. Since present experiment concerned with only As removal
from pure water, As removal and removal mechanism in natural
condition of intestinal milieu should be assessed in future studies.
Abstract: Bus Rapid Transit (BRT) has emerged as a cost-effective transport system for urban mobility. However its ability to stimulate land development remains largely unexplored. The study makes use of qualitative (interview method) and quantitative analysis (questionnaire survey and longitudinal analysis of property data) to investigate land development impact resulting from BRT in Beijing, China. The empirical analysis suggests that BRT has a positive impact on the residential and commercial property attractiveness along the busway corridor. The statistical analysis suggests that accessibility advantage conferred by BRT is capitalized into higher property price. The average price of apartments adjacent to a BRT station has gained a relatively faster increase than those not served by the BRT system. The capitalization effect mostly occurs after the full operation of BRT, and is more evident over time and particularly observed in areas which previously lack alternative mobility opportunity.
Abstract: Harmonic pollution and low power factor in power
systems caused by power converters have been of great concern. To
overcome these problems several converter topologies using
advanced semiconductor devices and control schemes have been
proposed. This investigation is to identify a low cost, small size,
efficient and reliable ac to dc converter to meet the input performance
index of UPS. The performance of single phase and three phase ac to
dc converter along with various control techniques are studied and
compared. The half bridge converter topology with linear current
control is identified as most suitable. It is simple, energy efficient
because of single switch power loss and transformer-less operation of
UPS. The results are validated practically using a prototype built
using IGBT and analog controller. The performance for both single
and three-phase system is verified. Digital implementation of closed
loop control achieves higher reliability. Its cost largely depends on
chosen bit precision. The minimal bit precision for optimum
converter performance is identified as 16-bit with fixed-point
operation. From the investigation and practical implementation it is
concluded that half bridge ac – dc converter along with digital linear
controller meets the performance index of UPS for single and three
phase systems.
Abstract: Chikungunya virus (CHICKV) is an arboviruses belonging to family Tagoviridae and is transmitted to human through by mosquito (Aedes aegypti and Aedes albopictus) bite. A large outbreak of chikungunya has been reported in India between 2006 and 2007, along with several other countries from South-East Asia and for the first time in Europe. It was for the first time that the CHICKV outbreak has been reported with mortality from Reunion Island and increased mortality from Asian countries. CHICKV affects all age groups, and currently there are no specific drugs or vaccine to cure the disease. The need of antiviral agents for the treatment of CHICKV infection and the success of virtual screening against many therapeutically valuable targets led us to carry out the structure based drug design against Chikungunya nSP2 protease (PDB: 3TRK). Highthroughput virtual screening of publicly available databases, ZINC12 and BindingDB, has been carried out using the Openeye tools and Schrodinger LLC software packages. Openeye Filter program has been used to filter the database and the filtered outputs were docked using HTVS protocol implemented in GLIDE package of Schrodinger LLC. The top HITS were further used for enriching the similar molecules from the database through vROCS; a shape based screening protocol implemented in Openeye. The approach adopted has provided different scaffolds as HITS against CHICKV protease. Three scaffolds: Indole, Pyrazole and Sulphone derivatives were selected based on the docking score and synthetic feasibility. Derivatives of Pyrazole were synthesized and submitted for antiviral screening against CHICKV.
Abstract: Pre-germinated parboiled brown rice or Khao hang (in Thai) is paddy which undergoing the processes of soaking, steaming, drying and dehusking to obtain the edible form for consumption. The objectives of this research were to study the kinetic of pre-germinated parboiled brown rice drying using fluidization technique and to study the properties of pre-germinated parboiled brown rice after drying. The dryings were performed at the different temperatures of 110, 120 and 130 oC at the bed depth of 2 cm with the air velocity of 1.98 m/s. The results found that the higher drying temperature led to the faster moisture reduction. After drying until the moisture content of pre-germinated parboiled brown rice was lower than 14%wet basis, samples were taken to determine various qualities such as percentage of head rice and L* a* b* color values. The shade drying was used as a control. The results found that the higher drying temperature resulted in the decrease of head rice percentage. For the color assessment, the trend of L* and a* values was increased with the drying temperature, while the b* value was not significantly difference (p › 0.05) by drying temperatures. However, the b value of drying by fluidized bed dryer was higher than the control.
Abstract: Lately management strategy that put Industrial Design (ID) in its core is recognized more important, as technology and price alone cannot differentiate a product. The needs to shorten the time to develop a product also shorten the development period of ID, and it necessitates the ID process management. This research analyzes the status of integration process of ID and Engineering Design (ED) of office equipment that requires the collaboration of ID and ED to clarify the issues for the efficiency of the development and to propose solutions.
Abstract: Data warehouse is a dedicated database used for querying and reporting. Queries in this environment show special characteristics such as multidimensionality and aggregation. Exploiting the nature of queries, in this paper we propose a query driven design framework. The proposed framework is general and allows a designer to generate a schema based on a set of queries.
Abstract: Fault-proneness of a software module is the
probability that the module contains faults. A correlation exists
between the fault-proneness of the software and the measurable
attributes of the code (i.e. the static metrics) and of the testing (i.e.
the dynamic metrics). Early detection of fault-prone software
components enables verification experts to concentrate their time and
resources on the problem areas of the software system under
development. This paper introduces Genetic Algorithm based
software fault prediction models with Object-Oriented metrics. The
contribution of this paper is that it has used Metric values of JEdit
open source software for generation of the rules for the classification
of software modules in the categories of Faulty and non faulty
modules and thereafter empirically validation is performed. The
results shows that Genetic algorithm approach can be used for
finding the fault proneness in object oriented software components.