Abstract: The removal efficiency of 4-chlorophenol with
different advanced oxidation processes have been studied. Oxidation
experiments were carried out using two 4-chlorophenol
concentrations: 100 mg L-1 and 250 mg L-1 and UV generated from a
KrCl excilamp with (molar ratio H2O2: 4-chlorophenol = 25:1) and
without H2O2, and, with Fenton process (molar ratio H2O2:4-
chlorophenol of 25:1 and Fe2+ concentration of 5 mg L-1).
The results show that there is no significant difference in the 4-
chlorophenol conversion when using one of the three assayed
methods. However, significant concentrations of the photoproductos
still remained in the media when the chosen treatment involves UV
without hydrogen peroxide. Fenton process removed all the
intermediate photoproducts except for the hydroquinone and the
1,2,4-trihydroxybenzene. In the case of UV and hydrogen peroxide
all the intermediate photoproducts are removed.
Microbial bioassays were carried out utilising the naturally
luminescent bacterium Vibrio fischeri and a genetically modified
Pseudomonas putida isolated from a waste treatment plant receiving
phenolic waste. The results using V. fischeri show that with samples
after degradation, only the UV treatment showed toxicity (IC50 =38)
whereas with H2O2 and Fenton reactions the samples exhibited no
toxicity after treatment in the range of concentrations studied. Using
the Pseudomonas putida biosensor no toxicity could be detected for
all the samples following treatment due to the higher tolerance of the
organism to phenol concentrations encountered.
Abstract: In the present work, behavior of inoxydable steel as
reinforcement bar in composite concrete is being investigated. The
bar-concrete adherence in reinforced concrete (RC) beam is studied
and focus is made on the tension stiffening parameter. This study
highlighted an approach to observe this interaction behavior in
bending test instead of direct tension as per reported in many
references. The approach resembles actual loading condition of the
structural RC beam. The tension stiffening properties are then
applied to numerical finite element analysis (FEA) to verify their
correlation with laboratory results. Comparison with laboratory
shows a good correlation between the two. The experimental settings
is able to determine tension stiffening parameters in RC beam and
the modeling strategies made in ABAQUS can closely represent the
actual condition. Tension stiffening model used can represent the
interaction properties between inoxydable steel and concrete.
Abstract: Prior to the use of detectors, characteristics
comparison study was performed and baseline established. In patient
specific QA, the portal dosimetry mean values of area gamma,
average gamma and maximum gamma were 1.02, 0.31 and 1.31 with
standard deviation of 0.33, 0.03 and 0.14 for IMRT and the
corresponding values were 1.58, 0.48 and 1.73 with standard
deviation of 0.31, 0.06 and 0.66 for VMAT. With ImatriXX 2-D
array system, on an average 99.35% of the pixels passed the criteria
of 3%-3 mm gamma with standard deviation of 0.24 for dynamic
IMRT. For VMAT, the average value was 98.16% with a standard
deviation of 0.86. The results showed that both the systems can be
used in patient specific QA measurements for IMRT and VMAT.
The values obtained with the portal dosimetry system were found to
be relatively more consistent compared to those obtained with
ImatriXX 2-D array system.
Abstract: In this paper, the action research driven design of a
context relevant, developmental peer review of teaching model, its
implementation strategy and its impact at an Australian university is
presented. PRO-Teaching realizes an innovative process that
triangulates contemporaneous teaching quality data from a range of
stakeholders including students, discipline academics, learning and
teaching expert academics, and teacher reflection to create reliable
evidence of teaching quality. Data collected over multiple classroom
observations allows objective reporting on development differentials
in constructive alignment, peer, and student evaluations. Further
innovation is realized in the application of this highly structured
developmental process to provide summative evidence of sufficient
validity to support claims for professional advancement and learning
and teaching awards. Design decision points and contextual triggers
are described within the operating domain. Academics and
developers seeking to introduce structured peer review of teaching
into their organization will find this paper a useful reference.
Abstract: In this paper, a decision aid method for preoptimization
is presented. The method is called “negotiation", and it
is based on the identification, formulation, modeling and use of
indicators defined as “negotiation indicators". These negotiation
indicators are used to explore the solution space by means of a classbased
approach. The classes are subdomains for the negotiation
indicators domain. They represent equivalent cognitive solutions in
terms of the negotiation indictors being used. By this method, we
reduced the size of the solution space and the criteria, thus aiding the
optimization methods. We present an example to show the method.
Abstract: As a part of the development of a numerical method of
close capture exhausts systems for machining devices, a test rig
recreating a situation similar to a grinding operation, but in a
perfectly controlled environment, is used. The properties of the
obtained spray of solid particles are initially characterized using
particle tracking velocimetry (PTV), in order to obtain input and
validation parameters for numerical simulations. The dispersion of a
tracer gas (SF6) emitted simultaneously with the particle jet is then
studied experimentally, as the dispersion of such a gas is
representative of that of finer particles, whose aerodynamic response
time is negligible. Finally, complete modeling of the test rig is
achieved to allow comparison with experimental results and thus to
progress towards validation of the models used to describe a twophase
flow generated by machining operation.
Abstract: This paper is described one of the intelligent control method in Autonomous systems, which is called fuzzy control to correct the three wheel omnidirectional robot movement while it make mistake to catch the target. Fuzzy logic is especially advantageous for problems that can not be easily represented by mathematical modeling because data is either unavailable, incomplete or the process is too complex. Such systems can be easily up grated by adding new rules to improve performance or add new features. In many cases , fuzzy control can be used to improve existing traditional controller systems by adding an extra layer of intelligence to the current control method. The fuzzy controller designed here is more accurate and flexible than the traditional controllers. The project is done at MRL middle size soccer robot team.
Abstract: In this paper, multilayered coreless printed circuit
board (PCB) step-down power transformers for DC-DC converter
applications have been designed, manufactured and evaluated. A set
of two different circular spiral step-down transformers were
fabricated in the four layered PCB. These transformers have been
modelled with the assistance of high frequency equivalent circuit and
characterized with both sinusoidal and square wave excitation. This
paper provides the comparative results of these two different
transformers in terms of their resistances, self, leakage, mutual
inductances, coupling coefficient and also their energy efficiencies.
The operating regions for optimal performance of these transformers
for power transfer applications are determined. These transformers
were tested for the output power levels of about 30 Watts within the
input voltage range of 12-50 Vrms. The energy efficiency for these
step down transformers is observed to be in the range of 90%-97% in
MHz frequency region.
Abstract: This study comprehensively simulate the use of k-ε
model for predicting flow and heat transfer with measured flow field
data in a stationary duct with elucidates on the detailed physics
encountered in the fully developed flow region, and the sharp 180°
bend region. Among the major flow features predicted with accuracy
are flow transition at the entrance of the duct, the distribution of
mean and turbulent quantities in the developing, fully developed, and
sharp 180° bend, the development of secondary flows in the duct
cross-section and the sharp 180° bend, and heat transfer
augmentation. Turbulence intensities in the sharp 180° bend are
found to reach high values and local heat transfer comparisons show
that the heat transfer augmentation shifts towards the wall and along
the duct. Therefore, understanding of the unsteady heat transfer in
sharp 180° bends is important. The design and simulation are related
to concept of fluid mechanics, heat transfer and thermodynamics.
Simulation study has been conducted on the response of turbulent
flow in a rectangular duct in order to evaluate the heat transfer rate
along the small scale multiple rectangular duct
Abstract: Load balancing is the process of improving the
performance of a parallel and distributed system through a
redistribution of load among the processors [1] [5]. In this paper we
present the performance analysis of various load balancing
algorithms based on different parameters, considering two typical
load balancing approaches static and dynamic. The analysis indicates
that static and dynamic both types of algorithm can have
advancements as well as weaknesses over each other. Deciding type
of algorithm to be implemented will be based on type of parallel
applications to solve. The main purpose of this paper is to help in
design of new algorithms in future by studying the behavior of
various existing algorithms.
Abstract: In this paper, we consider Wiener nonlinear model for solid oxide fuel cell (SOFC). The Wiener model of the SOFC consists of a linear dynamic block and a static output non-linearity followed by the block, in which linear part is approximated by state-space model and the nonlinear part is identified by a polynomial form. To control the SOFC system, we have to consider various view points such as operating conditions, another constraint conditions, change of load current and so on. A change of load current is the significant one of these for good performance of the SOFC system. In order to keep the constant stack terminal voltage by changing load current, the nonlinear model predictive control (MPC) is proposed in this paper. After primary control method is designed to guarantee the fuel utilization as a proper constant, a nonlinear model predictive control based on the Wiener model is developed to control the stack terminal voltage of the SOFC system. Simulation results verify the possibility of the proposed Wiener model and MPC method to control of SOFC system.
Abstract: This paper reports on the results of experimental
investigations of flash evaporation from superheated jet issues
vertically upward from a round straight nozzle of 81.3 mm diameter.
For the investigated range of jet superheat degree and velocity, it was
shown that flash evaporation enhances with initial temperature
increase. Due to the increase of jet inertia and subsequently the delay
of jet shattering, increase of jet velocity was found to result in
increase of evaporation "delay period". An empirical equation
predicts the jet evaporation completion height was developed, this
equation is thought to be useful in designing the flash evaporation
chamber. In attempts for enhancement of flash evaporation, use of
steel wire mesh located at short distance downstream was found
effective with no consequent pressure drop.
Abstract: Groundwater resources in Arsanjan plain provide
water for agriculture, industry, and human consumption. Continued
agricultural development in this area needs to additional groundwater
resources for, particularly during of drought periods, and effects on
the quantity and quality of ground water available. The purpose of
this study is to evaluate water level changes in the aquifer of
Arsanjan plain in the Fars province in order to determine the areas of
greatest depletion and the causes of depletion. In this plain, farmers
and other users are pumping groundwater faster than its natural
replenishment rate, causing a continuous drop in groundwater tables
and depletion of this resource. In this research variation of
groundwater level, their effects and ways to help control groundwater
levels in aquifer of the Arsanjan plains were evaluated .Excessive
exploitation of groundwater in this aquifer caused the groundwater
levels fall too fast or to unacceptable levels. The average drawdown
of the groundwater level in this plain were 19.66 meters during
1996 to 2003.
Abstract: In order to realize long-lived electric propulsion
systems, we have been investigating an electrodeless plasma thruster.
In our concept, a helicon plasma is accelerated by the magnetic nozzle
for the thrusts production. In addition, the electromagnetic thrust can
be enhanced by the additional radio-frequency rotating electric field
(REF) power in the magnetic nozzle. In this study, a direct
measurement of the electromagnetic thrust and a probe measurement
have been conducted using a laboratory model of the thruster under the
condition without the REF power input. Fromthrust measurement, it is
shown that the thruster produces a sub-milli-newton order
electromagnetic thrust force without the additional REF power. The
thrust force and the density jump are observed due to the discharge
mode transition from the inductive coupled plasma to the helicon wave
excited plasma. The thermal thrust is theoretically estimated, and the
total thrust force, which is a sum of the electromagnetic and the
thermal thrust force and specific impulse are calculated to be up to 650
μN (plasma production power of 400 W, Ar gas mass flow rate of 1.0
mg/s) and 210 s (plasma production power of 400 W, Ar gas mass flow
rate of 0.2 mg/s), respectively.
Abstract: The fast technology and economic growth in China has
attracted global attention in its tourism development. This study makes
an effort on investigating China-s online tourism market and the
Chinese online travelers- perceptions of hotel websites. The findings
are expected to better understand Chinese customers- online
preference and identified the differences among online travelers from
different regions in the country. Empirical findings showed online
reservation information is the most important factor to Chinese
customers, and tourists from different regions of China have
perception difference on user-friendly factor. The findings benefit
hoteliers from understanding their websites development and
formulating more appropriate online strategies to meet the
requirements of Chinese travelers.
Abstract: Functional Magnetic Resonance Imaging(fMRI) is a
noninvasive imaging technique that measures the hemodynamic
response related to neural activity in the human brain. Event-related
functional magnetic resonance imaging (efMRI) is a form of
functional Magnetic Resonance Imaging (fMRI) in which a series of
fMRI images are time-locked to a stimulus presentation and averaged
together over many trials. Again an event related potential (ERP) is a
measured brain response that is directly the result of a thought or
perception. Here the neuronal response of human visual cortex in
normal healthy patients have been studied. The patients were asked
to perform a visual three choice reaction task; from the relative
response of each patient corresponding neuronal activity in visual
cortex was imaged. The average number of neurons in the adult
human primary visual cortex, in each hemisphere has been estimated
at around 140 million. Statistical analysis of this experiment was
done with SPM5(Statistical Parametric Mapping version 5) software.
The result shows a robust design of imaging the neuronal activity of
human visual cortex.
Abstract: The main aim of this work is to develop a model of hydrogen sulfide (H2S) separation from natural gas by using membrane separation technology. The model is developed by incorporating three diffusion mechanisms which are Knudsen, viscous and surface diffusion towards membrane selectivity and permeability. The findings from the simulation result shows that the permeability of the gas is dependent toward the pore size of the membrane, operating pressure, operating temperature as well as feed composition. The permeability of methane has the highest value for Poly (1-trimethylsilyl-1-propyne ) PTMSP membrane at pore size of 0.1nm and decreasing toward a minimum peak at pore range 1 to 1.5 nm as pore size increased before it increase again for pore size is greater than 1.5 nm. On the other hand, the permeability of hydrogen sulfide is found to increase almost proportionally with the increase of membrane pore size. Generally, the increase of pressure will increase the permeability of gas since more driving force is provided to the system while increasing of temperature would decrease the permeability due to the surface diffusion drop off effect. A corroboration of the simulation result also showed a good agreement with the experimental data.
Abstract: Client expectations and preferences about therapy
represent an important area of investigation as research shows they
are linked to engagement in therapy and therapy outcomes. Studies
examining young people-s expectations and preferences of therapy
remain a neglected area of research. The present study explored what
expectations and preferences young people seeking professional help
held regarding: their role as a client, their therapist-s role, their
therapeutic outcomes, and the processes of therapy. Gender and age
differences were also examined. Participants included 188 young
people aged 12-25 who completed a survey while attending their
initial session at a youth mental health service. Data were analysed
using quantitative methods. Results found the young people held
significantly more pessimistic expectations around therapy when
compared to what they had wanted therapy to be like. Few age and
gender differences were found. Results highlight the importance of a
collaborative therapy approach when working with young people.
Abstract: Experimental investigation has been carried out
towards understanding the complex fluid dynamics involved in the
interaction of vortical structures with zero pressure gradient boundary
layer. A laminar boundary layer is produced on the flat plate placed
in the water flume and the synthetic jet actuator is deployed on top of
the plate at a definite distance from the leading edge. The synthetic
jet actuator has been designed in such a way that the to and fro
motion of the diaphragm is maneuvered at will by varying the
operating parameters to produce the typical streamwise vortical
structures namely hairpin and tilted vortices. PIV measurements are
made on the streamwise plane normal to the plate to evaluate their
interaction with the near wall fluid.
Abstract: An improved processing description to be employed in biosonar signal processing in a cochlea model is proposed and examined. It is compared to conventional models using a modified discrimination analysis and both are tested. Their performances are evaluated with echo data captured from natural targets (trees).Results indicate that the phase characteristics of low-pass filters employed in the echo processing have a significant effect on class separability for this data.