Abstract: In this study, to accurately predict cavitation of a
centrifugal pump, numerical analysis was compared with experimental
results modeled on a small industrial centrifugal pump. In this study,
numerical analysis was compared with experimental results modeled
on a small industrial centrifugal pump for reliable prediction on
cavitation of a centrifugal pump. To improve validity of the numerical
analysis, transient analysis was conducted on the calculated domain of
full-type geometry, such as an experimental apparatus. The numerical
analysis from the results was considered to be a reliable prediction of
cavitaion.
Abstract: Direct Torque Control is a control technique in AC
drive systems to obtain high performance torque control. The
conventional DTC drive contains a pair of hysteresis comparators.
DTC drives utilizing hysteresis comparators suffer from high torque
ripple and variable switching frequency. The most common solution
to those problems is to use the space vector depends on the reference
torque and flux. In this Paper The space vector modulation technique
(SVPWM) is applied to 2 level inverter control in the proposed
DTC-based induction motor drive system, thereby dramatically
reducing the torque ripple. Then the controller based on space vector
modulation is designed to be applied in the control of Induction
Motor (IM) with a three-level Inverter. This type of Inverter has
several advantages over the standard two-level VSI, such as a greater
number of levels in the output voltage waveforms, Lower dV/dt, less
harmonic distortion in voltage and current waveforms and lower
switching frequencies. This paper proposes a general SVPWM
algorithm for three-level based on standard two-level SVPWM. The
proposed scheme is described clearly and simulation results are
reported to demonstrate its effectiveness. The entire control scheme is
implemented with Matlab/Simulink.
Abstract: Glazing is a process used to reduce undesirable drying or dehydration of fish during frozen or cold storage. To evaluate the effect of the time/ temperature binomial of the cryogenic frozen tunnel in the amount of glazing watera Central Composite Rotatable Design was used, with application of the Response Surface Methodology. The results reveal that the time/ temperature obtained for pink cusk-eel in experimental conditions for glazing water are similar to the industrial process, but for red fish and merluza the industrial process needs some adjustments. Control charts were established and implementedto control the amount of glazing water on sardine and merluza. They show that the freezing process was statistically controlled but there were some tendencies that must be analyzed, since the trend of sample mean values approached either of the limits, mainly in merluza. Thus, appropriate actions must be taken, in order to improve the process.
Abstract: The aim of this study was to investigate whether
magnetite nanoparticles affect the viability of Bradyrhizobium
japanicum cells residing on the surface of soybean seeds during
desiccation. Different concentrations of nanoparticles suspended in
liquid medium, mixed with and adhering to Bradyrhizobium
japanicum, were investigated at two temperatures, using both
soybean seeds and glass beads as surrogates. Statistical design was a
complete randomized block (CRB) in a factorial 6×2×2×6
experimental arrangement with four replications. The most important
variable was the viability of Bradyrhizobium on the surface of the
seeds. The nanoparticles increased Bradyrhizobium viability and
inoculated seeds stored at low temperature had greater viability when
nanoparticles had been added. At the optimum nanoparticle
concentration, 50% bacterium viability on the seeds was retained
after 5 days at 4ºC. Possible explanations for the observed effects are
proposed.
Abstract: The combustion chamber dimensions have important
effects on pollutant emission in furnaces as a direct result of
temperature distribution and maximum temperature value. In this
paper the pollutant emission and the temperature distribution in two
cylindrical furnaces with different dimensions (with similar length to
diameter ratio) in similar condition have been investigated
experimentally. The furnace fuel is gas oil that is used with three
different flow rates. The results show that in these two cases the
temperature increases to its maximum value quickly, and then
decreases slowly. The results also show that increase in fuel flow rate
cause to increase in NOx emission in each case, but this increase is
greater in small furnace. With increase in fuel flow rate, CO emission
decreases firstly, and then it increases. Combustion efficiency
reduces with increase in fuel flow rate but the rate of reduction in
small furnace is greater than large furnace. The results of axial
temperature distribution have been compared with those have been
obtained numerically and experimentally by Moghiman.
Abstract: A fault detection and identification (FDI) technique is
presented to create a fault tolerant control system (FTC). The fault
detection is achieved by monitoring the position of the light source
using an array of light sensors. When a decision is made about the
presence of a fault an identification process is initiated to locate the
faulty component and reconfigure the controller signals. The signals
provided by the sensors are predictable; therefore the existence of a
fault is easily identified. Identification of the faulty sensor is based on
the dynamics of the frame. The technique is not restricted to a
particular type of controllers and the results show consistency.
Abstract: In this work, we address theoretically the influence of red and white Gaussian noise for electronic energies and eigenstates of cylindrically shaped quantum dots. The stochastic effect can be imagined as resulting from crystal-growth statistical fluctuations in the quantum-dot material composition. In particular we obtain analytical expressions for the eigenvalue shifts and electronic envelope functions in the k . p formalism due to stochastic variations in the confining band-edge potential. It is shown that white noise in the band-edge potential leaves electronic properties almost unaffected while red noise may lead to changes in state energies and envelopefunction amplitudes of several percentages. In the latter case, the ensemble-averaged envelope function decays as a function of distance. It is also shown that, in a stochastic system, constant ensembleaveraged envelope functions are the only bounded solutions for the infinite quantum-wire problem and the energy spectrum is completely discrete. In other words, the infinite stochastic quantum wire behaves, ensemble-averaged, as an atom.
Abstract: Radiolabeled cyclic RGD peptides targeting integrin αvβ3 are reported as promising agents for the early diagnosis of metastatic tumors. With an aim to improve tumor uptake and retention of the peptide, cyclic RGD peptide dimer E[c (RGDfK)] 2 (E = Glutamic acid, f = phenyl alanine, K = lysine) coupled to the bifunctional chelator DOTA was custom synthesized and radiolabelled with 68Ga. Radiolabelling of cyclic RGD peptide dimer with 68Ga was carried out using HEPES buffer and biological evaluation of the complex was done in nude mice bearing HT29 tumors.
Abstract: Wind catchers are traditional natural ventilation
systems attached to buildings in order to ventilate the indoor air. The
most common type of wind catcher is four sided one which is
capable to catch wind in all directions. CFD simulation is the perfect
way to evaluate the wind catcher performance. The accuracy of CFD
results is the issue of concern, so sensitivity analyses is crucial to
find out the effect of different settings of CFD on results. This paper
presents a series of 3D steady RANS simulations for a generic
isolated four-sided wind catcher attached to a room subjected to wind
direction ranging from 0º to 180º with an interval of 45º. The CFD
simulations are validated with detailed wind tunnel experiments. The
influence of an extensive range of computational parameters is
explored in this paper, including the resolution of the computational
grid, the size of the computational domain and the turbulence model.
This study found that CFD simulation is a reliable method for wind
catcher study, but it is less accurate in prediction of models with non
perpendicular wind directions.
Abstract: In this paper, a novel method for a biometric system based on the ECG signal is proposed, using spectral coefficients computed through linear predictive coding (LPC). ECG biometric systems have traditionally incorporated characteristics of fiducial points of the ECG signal as the feature set. These systems have been shown to contain loopholes and thus a non-fiducial system allows for tighter security. In the proposed system, incorporating non-fiducial features from the LPC spectrum produced a segment and subject recognition rate of 99.52% and 100% respectively. The recognition rates outperformed the biometric system that is based on the wavelet packet decomposition (WPD) algorithm in terms of recognition rates and computation time. This allows for LPC to be used in a practical ECG biometric system that requires fast, stringent and accurate recognition.
Abstract: Turbulent heat transfer to fluid flow through channel with triangular ribs of different angles are presented in this paper. Ansys 14 ICEM and Ansys 14 Fluent are used for meshing process and solving Navier stokes equations respectively. In this investigation three angles of triangular ribs with the range of Reynolds number varied from 20000 to 60000 at constant surface temperature are considered. The results show that the Nusselt number increases with the increase of Reynolds number for all cases at constant surface temperature. According to the profile of local Nusselt number on ribs walled of channel, the peak is at the midpoint between the two ribs. The maximum value of average Nusselt number is obtained for triangular ribs of angel 60°and at Reynolds number of 60000 compared to the Nusselt number for the ribs of angel 90° and 45° and at same Reynolds number. The recirculation regions generated by the ribs corresponding to the velocity streamline show the largest recirculation region at triangular ribs of angle 60° which also provides the highest enhancement of heat transfer.
Abstract: In this paper, a two-dimensional mathematical model is developed for estimating the extent of inland inundation due to Indonesian tsunami of 2004 along the coastal belts of Peninsular Malaysia and Thailand. The model consists of the shallow water equations together with open and coastal boundary conditions. In order to route the water wave towards the land, the coastal boundary is treated as a time dependent moving boundary. For computation of tsunami inundation, the initial tsunami wave is generated in the deep ocean with the strength of the Indonesian tsunami of 2004. Several numerical experiments are carried out by changing the slope of the beach to examine the extent of inundation with slope. The simulated inundation is found to decrease with the increase of the slope of the orography. Correlation between inundation / recession and run-up are found to be directly proportional to each other.
Abstract: A code has been developed in Mathematica using
Direct Simulation Monte Carlo (DSMC) technique. The code was
tested for 2-D air flow around a circular cylinder. Same geometry
and flow properties were used in FLUENT 6.2 for comparison. The
results obtained from Mathematica simulation indicated significant
agreement with FLUENT calculations, hence providing insight into
particle nature of fluid flows.
Abstract: There are extensive applications of lithium
bromide-water absorption chillers in industry, but the heat exchangers
corrosion and refrigerating capacity loss are very difficult to be solved.
In this paper, an experiment was conducted by using plastic heat
transfer tubes instead of copper tubes. As an example, for a lithium
bromide-water absorption chiller of refrigerating capacity of 35kW,
the correlative performance of the lithium bromide-water absorption
chiller using plastic heat transfer tubes was compared with the
traditional lithium bromide-water absorption chiller. And then the
following three aspects, i.e., heat transfer area, pipe resistance, and
safety strength, are analyzed. The results show that plastic heat
transfer tubes can be used on lithium bromide-water absorption
chillers, and its prospect is very optimistic.
Abstract: The main purpose of the research is to address the role of psychological harassment behaviors (mobbing) to which employees are exposed and personality characteristics over work alienation. Research population was composed of the employees of Provincial Special Administration. A survey with four sections was created to measure variables and reach out the basic goals of the research. Correlation and step-wise regression analyses were performed to investigate the separate and overall effects of sub-dimensions of psychological harassment behaviors and personality characteristic on work alienation of employees. Correlation analysis revealed significant but weak relationships between work alienation and psychological harassment and personality characteristics. Step-wise regression analysis revealed also significant relationships between work alienation variable and assault to personality, direct negative behaviors (sub dimensions of mobbing) and openness (sub-dimension of personality characteristics). Each variable was introduced into the model step by step to investigate the effects of significant variables in explaining the variations in work alienation. While the explanation ratio of the first model was 13%, the last model including three variables had an explanation ratio of 24%.
Abstract: Let T and S be a subspace of Cn and Cm, respectively.
Then for A ∈ Cm×n satisfied AT ⊕ S = Cm, the generalized
inverse A(2)
T,S is given by A(2)
T,S = (PS⊥APT )†. In this paper, a
finite formulae is presented to compute generalized inverse A(2)
T,S
under the concept of restricted inner product, which defined as <
A,B >T,S=< PS⊥APT,B > for the A,B ∈ Cm×n. By this
iterative method, when taken the initial matrix X0 = PTA∗PS⊥, the
generalized inverse A(2)
T,S can be obtained within at most mn iteration
steps in absence of roundoff errors. Finally given numerical example
is shown that the iterative formulae is quite efficient.
Abstract: The small interfering RNA (siRNA) alters the
regulatory role of mRNA during gene expression by translational
inhibition. Recent studies show that upregulation of mRNA because
serious diseases like cancer. So designing effective siRNA with good
knockdown effects plays an important role in gene silencing. Various
siRNA design tools had been developed earlier. In this work, we are
trying to analyze the existing good scoring second generation siRNA
predicting tools and to optimize the efficiency of siRNA prediction
by designing a computational model using Artificial Neural Network
and whole stacking energy (%G), which may help in gene silencing
and drug design in cancer therapy. Our model is trained and tested
against a large data set of siRNA sequences. Validation of our results
is done by finding correlation coefficient of experimental versus
observed inhibition efficacy of siRNA. We achieved a correlation
coefficient of 0.727 in our previous computational model and we
could improve the correlation coefficient up to 0.753 when the
threshold of whole tacking energy is greater than or equal to -32.5
kcal/mol.
Abstract: The aim of this research is to develop the
understanding of corporate social responsibility (CSR) from
consumers- perspective toward Thai mobile service providers.
Based on the survey from 400 mobile customers, the result
shows that four dimensions of CSR of Thai mobile service
providers consist of economic, legal, ethical and philanthropic
responsibility. These four CSR factors have positive impacts
on enhancing customer satisfaction except one item of
economic responsibility - profitability to shareholders. Ethical
dimension has the strongest impact on customer satisfaction.
Economic, legal, ethical, philanthropic responsibility and
customer satisfaction have major impact on loyalty, whilst
philanthropic component mostly affects loyalty.
Abstract: Location-aware computing is a type of pervasive
computing that utilizes user-s location as a dominant factor for
providing urban services and application-related usages. One of the
important urban services is navigation instruction for wayfinders in a
city especially when the user is a tourist. The services which are
presented to the tourists should provide adapted location aware
instructions. In order to achieve this goal, the main challenge is to
find spatial relevant objects and location-dependent information. The
aim of this paper is the development of a reusable location-aware
model to handle spatial relevancy parameters in urban location-aware
systems. In this way we utilized ontology as an approach which could
manage spatial relevancy by defining a generic model. Our
contribution is the introduction of an ontological model based on the
directed interval algebra principles. Indeed, it is assumed that the
basic elements of our ontology are the spatial intervals for the user
and his/her related contexts. The relationships between them would
model the spatial relevancy parameters. The implementation language
for the model is OWLs, a web ontology language. The achieved
results show that our proposed location-aware model and the
application adaptation strategies provide appropriate services for the
user.
Abstract: In order to accelerate the similarity search in highdimensional database, we propose a new hierarchical indexing method. It is composed of offline and online phases. Our contribution concerns both phases. In the offline phase, after gathering the whole of the data in clusters and constructing a hierarchical index, the main originality of our contribution consists to develop a method to construct bounding forms of clusters to avoid overlapping. For the online phase, our idea improves considerably performances of similarity search. However, for this second phase, we have also developed an adapted search algorithm. Our method baptized NOHIS (Non-Overlapping Hierarchical Index Structure) use the Principal Direction Divisive Partitioning (PDDP) as algorithm of clustering. The principle of the PDDP is to divide data recursively into two sub-clusters; division is done by using the hyper-plane orthogonal to the principal direction derived from the covariance matrix and passing through the centroid of the cluster to divide. Data of each two sub-clusters obtained are including by a minimum bounding rectangle (MBR). The two MBRs are directed according to the principal direction. Consequently, the nonoverlapping between the two forms is assured. Experiments use databases containing image descriptors. Results show that the proposed method outperforms sequential scan and SRtree in processing k-nearest neighbors.