Abstract: In this paper we study the resource allocation problem
for an OFDMA based cooperative two-way relaying (TWR) network.
We focus on amplify and forward (AF) analog network coding
(ANC) protocol. An optimization problem for two basic resources
namely, sub-carrier and power is formulated for multi-user TWR
networks. A joint optimal optimization problem is investigated and
two-step low complexity sub-optimal resource allocation algorithm is
proposed for multi-user TWR networks with ANC protocol. The
proposed algorithm has been evaluated in term of total achievable
system sum-rate and achievable individual sum-rate for each userpair.
The good tradeoff between system sum-rate and fairness is
observed in the two-step proportional resource allocation scheme.
Abstract: Motion control of flexible arms is more difficult than
that of rigid arms, however utilizing its dynamics enables improved
performance such as a fast motion in short operation time. This paper
investigates a ball throwing robot with one rigid link and one flexible
link. This robot throws a ball at a set speed with a proper control torque.
A mathematical model of this ball throwing robot is derived through
Hamilton’s principle. Several patterns of torque input are designed and
tested through the proposed simulation models. The parameters of
each torque input pattern is optimized and determined by chaos
embedded vector evaluated particle swarm optimization (CEVEPSO).
Then, the residual vibration of the manipulator after throwing is
suppressed with input shaping technique. Finally, a real experiment is
set up for the model checking.
Abstract: This research aimed to develop plasma system used in air conditioners. This developed plasma system could be installed in the air conditioners - all split type. The quality of air could be improved to be equal to present plasma system. Development processes were as follows: 1) to study the plasma system used in the air conditioners, 2) to design a plasma generator, 3) to develop the plasma generator, and 4) to test its performance in many types of the air conditioners. This plasma system was developed by AC high voltage – 14 kv with a frequency of 50 kHz. Carbon was a conductor to generate arc in air purifier system. The research was tested by installing the plasma generator in the air conditioners - wall type. Whereas, there were 3 types of installations: air flow out, air flow in, and room center. The result of the plasma generator installed in the air conditioners, split type, revealed that the air flow out installation provided the highest average of o-zone at 223 mg/h. This type of installation provided the highest efficiency of air quality improvement. Moreover, the air flow in installation and the room center installation provided the average of the o-zone at 163 mg/h and 64 mg/h, respectively.
Abstract: The enzyme alkaline protease production was determined under
solid state fermentation using the soil bacteria Serratia marcescens
sp7. The maximum production was obtained from wheat bran
medium than ground nut shell and chemically defined medium. The
physiological fermentation factors such as pH of the medium (pH 8),
Temperature (40oC) and incubation time (48 hrs) played a vital role
in alkaline protease production in all the above. 100Mm NaCl has
given better resolution during elution of the enzymes. The enzyme
production was found to be associated with growth of the bacterial
culture.
Abstract: This paper considers H∞ performance for Markovian jump systems with Time-varying delays. The systems under consideration involve disturbance signal, Markovian switching and timevarying delays. By using a new Lyapunov-Krasovskii functional and a convex optimization approach, a delay-dependent stability condition in terms of linear matrix inequality (LMI) is addressed, which guarantee asymptotical stability in mean square and a prescribed H∞ performance index for the considered systems. Two numerical examples are given to illustrate the effectiveness and the less conservatism of the proposed main results. All these results are expected to be of use in the study of stochastic systems with time-varying delays.
Abstract: This paper presents a heuristic approach to solve the Generalized Assignment Problem (GAP) which is NP-hard. It is worth mentioning that many researches used to develop algorithms for identifying the redundant constraints and variables in linear programming model. Some of the algorithms are presented using intercept matrix of the constraints to identify redundant constraints and variables prior to the start of the solution process. Here a new heuristic approach based on the dominance property of the intercept matrix to find optimal or near optimal solution of the GAP is proposed. In this heuristic, redundant variables of the GAP are identified by applying the dominance property of the intercept matrix repeatedly. This heuristic approach is tested for 90 benchmark problems of sizes upto 4000, taken from OR-library and the results are compared with optimum solutions. Computational complexity is proved to be O(mn2) of solving GAP using this approach. The performance of our heuristic is compared with the best state-ofthe- art heuristic algorithms with respect to both the quality of the solutions. The encouraging results especially for relatively large size test problems indicate that this heuristic approach can successfully be used for finding good solutions for highly constrained NP-hard problems.
Abstract: Carbonic anhydrases (CAs) has been focused as
biological catalysis for CO2 sequestration process because it can
catalyze the conversion of CO2 to bicarbonate. Here, codon-optimized
sequence of α type-CA cloned from Duneliala species. (DsCAopt) was
constructed, expressed, and characterized. The expression level in E.
coli BL21(DE3) was better for codon-optimized DsCAopt than intact
sequence of DsCAopt. DsCAopt enzyme shows high-stability at pH
7.6/10.0. In final, we demonstrated that in the Ca2+ solution, DsCAopt
enzyme can catalyze well the conversion of CO2 to CaCO3, as the
calcite form.
Abstract: In this work, an attempt is made to design an optimal
wind/pv/diesel hybrid power system for a village of Ain Merane,
Chlef, Algeria, where the wind speed and solar radiation
measurements were made. The aim of this paper is the optimization
of a hybrid wind/solar/diesel system applied in term of technical and
economic feasibility by simulation using HOMER. A comparison
was made between the performance of wind/pv/diesel system and the
classic connecting system.
Abstract: An optimal control problem for a mathematical model of efficiency of antiviral therapy in hepatitis B virus infections is considered. The aim of the study is to control the new viral production, block the new infection cells and maintain the number of uninfected cells in the given range. The optimal controls represent the efficiency of antiviral therapy in inhibiting viral production and preventing new infections. Defining the cost functional, the optimal control problem is converted into the constrained optimization problem and the first order optimality system is derived. For the numerical simulation, we propose the steepest descent algorithm based on the adjoint variable method. A computer program in MATLAB is developed for the numerical simulations.
Abstract: In this paper multi-objective genetic algorithms are
employed for Pareto approach optimization of ideal Turboshaft
engines. In the multi-objective optimization a number of conflicting
objective functions are to be optimized simultaneously. The
important objective functions that have been considered for
optimization are specific thrust (F/m& 0), specific fuel consumption
( P S ), output shaft power 0 (& /&) shaft W m and overall efficiency( ) O
η .
These objectives are usually conflicting with each other. The design
variables consist of thermodynamic parameters (compressor pressure
ratio, turbine temperature ratio and Mach number).
At the first stage single objective optimization has been
investigated and the method of NSGA-II has been used for multiobjective
optimization. Optimization procedures are performed for
two and four objective functions and the results are compared for
ideal Turboshaft engine. In order to investigate the optimal
thermodynamic behavior of two objectives, different set, each
including two objectives of output parameters, are considered
individually. For each set Pareto front are depicted. The sets of
selected decision variables based on this Pareto front, will cause the
best possible combination of corresponding objective functions.
There is no superiority for the points on the Pareto front figure,
but they are superior to any other point. In the case of four objective
optimization the results are given in tables.
Abstract: In the last decades to supply the various and different
demands of clients, a lot of manufacturers trend to use the mixedmodel
assembly line (MMAL) in their production lines, since this
policy make possible to assemble various and different models of the
equivalent goods on the same line with the MTO approach.
In this article, we determine the sequence of (MMAL) line, with
applying the kitting approach and planning of rest time for general
workers to reduce the wastages, increase the workers effectiveness
and apply the sector of lean production approach.
This Multi-objective sequencing problem solved in small size with
GAMS22.2 and PSO meta heuristic in 10 test problems and compare
their results together and conclude that their results are very similar
together, next we determine the important factors in computing the
cost, which improving them cost reduced. Since this problem, is NPhard
in large size, we use the particle swarm optimization (PSO)
meta-heuristic for solving it. In large size we define some test
problems to survey it-s performance and determine the important
factors in calculating the cost, that by change or improved them
production in minimum cost will be possible.
Abstract: This study has investigated a vehicle Lumped
Parameter Model (LPM) in frontal crash. There are several ways for
determining spring and damper characteristics and type of problem
shall be considered as system identification. This study use Genetic
Algorithm (GA) procedure, being an effective procedure in case of
optimization issues, for optimizing errors, between target data
(experimental data) and calculated results (being obtained by
analytical solving). In this study analyzed model in 5-DOF then
compared our results with 5-DOF serial model. Finally, the response
of model due to external excitement is investigated.
Abstract: This paper proposes improved delay-dependent stability conditions of the linear time-delay systems of neutral type. The proposed methods employ a suitable Lyapunov-Krasovskii’s functional and a new form of the augmented system. New delay-dependent stability criteria for the systems are established in terms of Linear matrix inequalities (LMIs) which can be easily solved by various effective optimization algorithms. Numerical examples showed that the proposed method is effective and can provide less conservative results.
Abstract: Manganese steel (Hadfield) is one of the important
alloys in industry due to its special properties. High work hardening
ability with appropriate toughness and ductility are the properties that
caused this alloy to be used in wear resistance parts and in high
strength condition. Heat treatment is the main process through which
the desired mechanical properties and microstructures are obtained in
Hadfield steel. In this study various heat treatment cycles, differing in
austenising temperature, time and quenching solution are applied. For
this purpose, the same samples of manganese steel was heat treated in
9 different cycles, and then the mechanical properties and
microstructures were investigated. Based on the results of the study,
the optimum heat treatment cycle was obtained.
Abstract: Among the chemicals used for ammunition production, TNT (Trinitrotoluene) play a significant role since World War I and II. Various types of military weapon utilize TNT in casting process. However, the TNT casting process for warhead is difficult to control the cooling rate of the liquid TNT. This problem occurs because the casting process lacks the equipment to detect the temperature during the casting procedure This study presents the temperature detected by infrared camera to illustrate the cooling rate and cooling zone of curing, and demonstrates the optimization of TNT condition to reduce the risk of air gap occurred in the warhead which can result in the destruction afterward. Premature initiation of explosive-filled projectiles in response to set-back forces during gunfiring cause by casting defects. Finally the study can help improving the process of the TNT casting. The operators can control the curing of TNT inside the case by rising up the heating rod at the proper time. Consequently this can reduce tremendous time of rework if the air gaps occur and increase strength to lower elastic modulus. Therefore, it can be clearly concluded that the use of Infrared Cameras in this process is another method to improve the casting procedure.
Abstract: This paper discusses a genetic algorithm (GA) based optimal load shedding that can apply for electrical distribution networks with and without dispersed generators (DG). Also, the proposed method has the ability for considering constant and variable capacity deficiency caused by unscheduled outages in the bulked generation and transmission system of bulked power supply. The genetic algorithm (GA) is employed to search for the optimal load shedding strategy in distribution networks considering DGs in two cases of constant and variable modelling of bulked power supply of distribution networks. Electrical power distribution systems have a radial network and unidirectional power flows. With the advent of dispersed generations, the electrical distribution system has a locally looped network and bidirectional power flows. Therefore, installed DG in the electrical distribution systems can cause operational problems and impact on existing operational schemes. Introduction of DGs in electrical distribution systems has introduced many new issues in operational and planning level. Load shedding as one of operational issue has no exempt. The objective is to minimize the sum of curtailed load and also system losses within the frame-work of system operational and security constraints. The proposed method is tested on a radial distribution system with 33 load points for more practical applications.
Abstract: Malting is usually carried out on intact barley seed,
while hull is still attached to it. In this study, oat grain with and
without hull was subjected to controlled germination to optimize its
enzymes activity, in such a way that lipase has the lowest and α-
amylase and proteinase the highest activities. Since pH has a great
impact on the activity of the enzymes, the pH of germination media
was set up to 3 to 8. In dehulled oats, lipase and α-amylase had the
lowest and highest activities in pHs 3 and 6, respectively whereas the
highest proteinase activity was evidenced at pH 7 and 4 in the oats
with and without hull respectively. While measurements indicated
that the effect of hull on the enzyme activities particularly in lipase
and amylase at each level of the pH are significantly different, the
best results were obtained in those samples in which their hull had
been removed. However, since the similar lipase activity in
germinated dehulled oat were recorded at the pHs 4 and 5, therefore
it was concluded that pH 5 in dehulled oat seed may provide the
optimum enzyme activity for all the enzymes.
Abstract: The approach proposed here is oriented in the direction of fuzzy system for the analysis and the synthesis of intelligent climate controllers, the simulation of the internal climate of the greenhouse is achieved by a linear model whose coefficients are obtained by identification. The use of fuzzy logic controllers for the regulation of climate variables represents a powerful way to minimize the energy cost. Strategies of reduction and optimization are adopted to facilitate the tuning and to reduce the complexity of the controller.
Abstract: This paper presents a multi-objective order allocation
planning problem with the consideration of various real-world
production features. A novel hybrid intelligent optimization model,
integrating a multi-objective memetic optimization process, a Monte
Carlo simulation technique and a heuristic pruning technique, is
proposed to handle this problem. Experiments based on industrial data
are conducted to validate the proposed model. Results show that (1)
the proposed model can effectively solve the investigated problem by
providing effective production decision-making solutions, which
outperformsan NSGA-II-based optimization process and an industrial
method.
Abstract: This paper proposes the method combining artificial
neural network (ANN) with particle swarm optimization (PSO) to
implement the maximum power point tracking (MPPT) by controlling
the rotor speed of the wind generator. First, the measurements of wind
speed, rotor speed of wind power generator and output power of wind
power generator are applied to train artificial neural network and to
estimate the wind speed. Second, the method mentioned above is
applied to estimate and control the optimal rotor speed of the wind
turbine so as to output the maximum power. Finally, the result reveals
that the control system discussed in this paper extracts the maximum
output power of wind generator within the short duration even in the
conditions of wind speed and load impedance variation.