Abstract: As a part of an evaluation system for R&D programs,
the Korean Government has applied the preliminary feasibility study
to new government R&D program plans. Basically, the fundamental purpose of the preliminary feasibility study is to decide that the
government will either do or do not invest in a new R&D Program. Additionally, the preliminary feasibility study can contribute to the
improvement of R&D program plans. For example, 2 cases of new
R&D program plans applied to the study are explained in this paper and there are expectations that these R&D programs would yield better
performance than without the study. It is thought that the important point of the preliminary feasibility study is not only the effective
decision making process of R&D program but also the opportunity to improve R&D program plan actually.
Abstract: A method based on the power series solution is proposed to solve the natural frequency of flapping vibration for the rotating inclined Euler beam with constant angular velocity. The vibration of the rotating beam is measured from the position of the corresponding steady state axial deformation. In this paper the governing equations for linear vibration of a rotating Euler beam are derived by the d'Alembert principle, the virtual work principle and the consistent linearization of the fully geometrically nonlinear beam theory in a rotating coordinate system. The governing equation for flapping vibration of the rotating inclined Euler beam is linear ordinary differential equation with variable coefficients and is solved by a power series with four independent coefficients. Substituting the power series solution into the corresponding boundary conditions at two end nodes of the rotating beam, a set of homogeneous equations can be obtained. The natural frequencies may be determined by solving the homogeneous equations using the bisection method. Numerical examples are studied to investigate the effect of inclination angle on the natural frequency of flapping vibration for rotating inclined Euler beams with different angular velocity and slenderness ratio.
Abstract: A digital system is proposed for low power 100-
channel neural recording system in this paper, which consists of 100
amplifiers, 100 analog-to-digital converters (ADC), digital controller
and baseband, transceiver for data link and RF command link. The
proposed system is designed in a 0.18 μm CMOS process and 65 nm
CMOS process.
Abstract: A Matlab based software for logistic regression is developed to enhance the process of teaching quantitative topics and assist researchers with analyzing wide area of applications where categorical data is involved. The software offers an option of performing stepwise logistic regression to select the most significant predictors. The software includes a feature to detect influential observations in data, and investigates the effect of dropping or misclassifying an observation on a predictor variable. The input data may consist either as a set of individual responses (yes/no) with the predictor variables or as grouped records summarizing various categories for each unique set of predictor variables' values. Graphical displays are used to output various statistical results and to assess the goodness of fit of the logistic regression model. The software recognizes possible convergence constraints when present in data, and the user is notified accordingly.
Abstract: Among various HLM techniques, the Multivariate Hierarchical Linear Model (MHLM) is desirable to use, particularly when multivariate criterion variables are collected and the covariance structure has information valuable for data analysis. In order to reflect prior information or to obtain stable results when the sample size and the number of groups are not sufficiently large, the Bayes method has often been employed in hierarchical data analysis. In these cases, although the Markov Chain Monte Carlo (MCMC) method is a rather powerful tool for parameter estimation, Procedures regarding MCMC have not been formulated for MHLM. For this reason, this research presents concrete procedures for parameter estimation through the use of the Gibbs samplers. Lastly, several future topics for the use of MCMC approach for HLM is discussed.
Abstract: Safety Health and Environment Code of Practice (SHE
COP) was developed to help road transportation operators to manage
its operation in a systematic and safe manner. A study was conducted
to determine the effectiveness of SHE COP implementation during
non-OPS period. The objective of the study is to evaluate the
implementations of SHE COP among bus operators during wee hour
operations. The data was collected by completing a set of checklist
after observing the activities during pre departure, during the trip, and
upon arrival. The results show that there are seven widely practiced
SHE COP elements. 22% of the buses have average speed exceeding
the maximum permissible speed on the highways (90 km/h), with
13% of the buses were travelling at the speed of more than 100 km/h.
The statistical analysis shows that there is only one significant
association which relates speeding with prior presence of
enforcement officers.
Abstract: This paper describes the project and development of a
very low-cost and small electronic prototype, especially designed for
monitoring and controlling existing home automation alarm systems
(intruder, smoke, gas, flood, etc.), via TCP/IP, with a typical web
browser. Its use will allow home owners to be immediately alerted
and aware when an alarm event occurs, and being also able to
interact with their home automation alarm system, disarming, arming
and watching event alerts, with a personal wireless Wi-Fi PDA or
smartphone logged on to a dedicated predefined web page, and using
also a PC or Laptop.
Abstract: This paper is focused on issues of nonlinear dynamic process modeling and model-based predictive control of a fed-batch sugar crystallization process applying the concept of artificial neural networks as computational tools. The control objective is to force the operation into following optimal supersaturation trajectory. It is achieved by manipulating the feed flow rate of sugar liquor/syrup, considered as the control input. A feed forward neural network (FFNN) model of the process is first built as part of the controller structure to predict the process response over a specified (prediction) horizon. The predictions are supplied to an optimization procedure to determine the values of the control action over a specified (control) horizon that minimizes a predefined performance index. The control task is rather challenging due to the strong nonlinearity of the process dynamics and variations in the crystallization kinetics. However, the simulation results demonstrated smooth behavior of the control actions and satisfactory reference tracking.
Abstract: Technology transfer of renewable energy technologies is very often unsuccessful in the developing world. Aside from challenges that have social, economic, financial, institutional and environmental dimensions, technology transfer has generally been misunderstood, and largely seen as mere delivery of high tech equipment from developed to developing countries or within the developing world from R&D institutions to society. Technology transfer entails much more, including, but not limited to: entire systems and their component parts, know-how, goods and services, equipment, and organisational and managerial procedures. Means to facilitate the successful transfer of energy technologies, including the sharing of lessons are subsequently extremely important for developing countries as they grapple with increasing energy needs to sustain adequate economic growth and development. Improving the success of technology transfer is an ongoing process as more projects are implemented, new problems are encountered and new lessons are learnt. Renewable energy is also critical to improve the quality of lives of the majority of people in developing countries. In rural areas energy is primarily traditional biomass. The consumption activities typically occur in an inefficient manner, thus working against the notion of sustainable development. This paper explores the implementation of technology transfer in the developing world (sub-Saharan Africa). The focus is necessarily on RETs since most rural energy initiatives are RETs-based. Additionally, it aims to highlight some lessons drawn from the cited RE projects and identifies notable differences where energy technology transfer was judged to be successful. This is done through a literature review based on a selection of documented case studies which are judged against the definition provided for technology transfer. This paper also puts forth research recommendations that might contribute to improved technology transfer in the developing world. Key findings of this paper include: Technology transfer cannot be complete without satisfying pre-conditions such as: affordability, maintenance (and associated plans), knowledge and skills transfer, appropriate know how, ownership and commitment, ability to adapt technology, sound business principles such as financial viability and sustainability, project management, relevance and many others. It is also shown that lessons are learnt in both successful and unsuccessful projects.
Abstract: Deep cold rolling (DCR) is a cold working process, which easily produces a smooth and work-hardened surface by plastic deformation of surface irregularities. In the present study, the influence of main deep cold rolling process parameters on the surface roughness and the hardness of AISI 4140 steel were studied by using fractional factorial design of experiments. The assessment of the surface integrity aspects on work material was done, in terms of identifying the predominant factor amongst the selected parameters, their order of significance and setting the levels of the factors for minimizing surface roughness and/or maximizing surface hardness. It was found that the ball diameter, rolling force, initial surface roughness and number of tool passes are the most pronounced parameters, which have great effects on the work piece-s surface during the deep cold rolling process. A simple, inexpensive and newly developed DCR tool, with interchangeable collet for using different ball diameters, was used throughout the experimental work presented in this paper.
Abstract: Numerical calculations of flow around a square cylinder are presented using the multi-relaxation-time lattice Boltzmann method at Reynolds number 150. The effects of upstream locations, downstream locations and blockage are investigated systematically. A detail analysis are given in terms of time-trace analysis of drag and lift coefficients, power spectra analysis of lift coefficient, vorticity contours visualizations and phase diagrams. A number of physical quantities mean drag coefficient, drag coefficient, Strouhal number and root-mean-square values of drag and lift coefficients are calculated and compared with the well resolved experimental data and numerical results available in open literature. The results had shown that the upstream, downstream and height of the computational domain are at least 7.5, 37.5 and 12 diameters of the cylinder, respectively.
Abstract: Dried soy protein hydrolysate powder was added to
the burger in order to enhance the oxidative stability as well as
decreases the microbial spoilage. The soybean bioactive compounds
(soy protein hydrolysate) as antioxidant and antimicrobial were added
at level of 1, 2 and 3 %.Chemical analysis and physical properties
were affected by protein hydrolysate addition. The TBA values were
significantly affected (P < 0.05) by the storage period and the level of
soy protein hydrolysate. All the tested soybean protein hydrolysate
additives showed strong antioxidant properties. Samples of soybean
protein hydrolysate showed the lowest (P < 0.05) TBA values at each
time of storage.
The counts of all determined microbiological indicators were
significantly (P < 0.05) affected by the addition of the soybean
protein hydrolysate. Decreasing trends of different extent were also
observed in samples of the treatments for total viable counts,
Coliform, Staphylococcus aureus, yeast and molds. Storage period
was being significantly (P < 0.05) affected on microbial counts in all
samples Staphylococcus aureus were the most sensitive microbe
followed by Coliform group of the sample containing protein
hydrolysate, while molds and yeast count showed a decreasing trend
but not significant (P < 0.05) until the end of the storage period
compared with control sample. Sensory attributes were also
performed, added protein hydrolysate exhibits beany flavor which
was clear about samples of 3% protein hydrolysate.
Abstract: The main aim of this study was to examine whether
people understand indicative conditionals on the basis of syntactic
factors or on the basis of subjective conditional probability. The
second aim was to investigate whether the conditional probability of
q given p depends on the antecedent and consequent sizes or derives
from inductive processes leading to establish a link of plausible cooccurrence
between events semantically or experientially associated.
These competing hypotheses have been tested through a 3 x 2 x 2 x 2
mixed design involving the manipulation of four variables: type of
instructions (“Consider the following statement to be true", “Read the
following statement" and condition with no conditional statement);
antecedent size (high/low); consequent size (high/low); statement
probability (high/low). The first variable was between-subjects, the
others were within-subjects. The inferences investigated were Modus
Ponens and Modus Tollens. Ninety undergraduates of the Second
University of Naples, without any prior knowledge of logic or
conditional reasoning, participated in this study.
Results suggest that people understand conditionals in a syntactic
way rather than in a probabilistic way, even though the perception of
the conditional probability of q given p is at least partially involved in
the conditionals- comprehension. They also showed that, in presence
of a conditional syllogism, inferences are not affected by the
antecedent or consequent sizes. From a theoretical point of view these
findings suggest that it would be inappropriate to abandon the idea
that conditionals are naturally understood in a syntactic way for the
idea that they are understood in a probabilistic way.
Abstract: The aim of this work is to analyze a viscous flow in
the axisymmetric nozzle taken into account the mesh size both in the
free stream and into the boundary layer. The resolution of the Navier-
Stokes equations is realized by using the finite volume method to
determine the supersonic flow parameters at the exit of convergingdiverging
nozzle. The numerical technique uses the Flux Vector
Splitting method of Van Leer. Here, adequate time stepping
parameter, along with CFL coefficient and mesh size level is selected
to ensure numerical convergence. The effect of the boundary layer
thickness is significant at the exit of the nozzle. The best solution is
obtained with using a very fine grid, especially near the wall, where
we have a strong variation of velocity, temperature and shear stress.
This study enabled us to confirm that the determination of boundary
layer thickness can be obtained only if the size of the mesh is lower
than a certain value limits given by our calculations.
Abstract: This article deals with the conceptual modeling under uncertainty. First, the division of information systems with their definition will be described, focusing on those where the construction of a conceptual model is suitable for the design of future information system database. Furthermore, the disadvantages of the traditional approach in creating a conceptual model and database design will be analyzed. A comprehensive methodology for the creation of a conceptual model based on analysis of client requirements and the selection of a suitable domain model is proposed here. This article presents the expert system used for the construction of a conceptual model and is a suitable tool for database designers to create a conceptual model.
Abstract: Nowadays, the pace of business change is such that,
increasingly, new functionality has to be realized and reliably
installed in a matter of days, or even hours. Consequently, more and
more business processes are prone to a continuous change. The
objective of the research in progress is to use the MAP model, in a
conceptual modeling method for flexible and adaptive business
process. This method can be used to capture the flexibility
dimensions of a business process; it takes inspiration from
modularity concept in the object oriented paradigm to establish a
hierarchical construction of the BP modeling. Its intent is to provide
a flexible modeling that allows companies to quickly adapt their
business processes.
Abstract: Human always tried to create a suitable situation for their life according to environmental conditions. In fact, geography has an important role in the shape of our living area. Iran also as a four-season country has different climate type: hot and humid, hot and dry, mid and humid, and cold; therefore, we can find different architecture styles in Iran. Gilan-s traditional architecture is a suitable sample of sustainable construction in Iran. Because the main factors of every dwelling are the climatic, social, economic and cultural effects which demonstrate the interaction between environment and people settlement. This paper was determined the interaction between environmental factors and the rural dwellings in the Gilan province. Also, traditional village (city) of Masouleh as a rare sample of rural and sustainable architecture was introduced.
Abstract: The objective of this paper, is to apply support vector machine (SVM) approach for the classification of cancerous and normal regions of prostate images. Three kinds of textural features are extracted and used for the analysis: parameters of the Gauss- Markov random field (GMRF), correlation function and relative entropy. Prostate images are acquired by the system consisting of a microscope, video camera and a digitizing board. Cross-validated classification over a database of 46 images is implemented to evaluate the performance. In SVM classification, sensitivity and specificity of 96.2% and 97.0% are achieved for the 32x32 pixel block sized data, respectively, with an overall accuracy of 96.6%. Classification performance is compared with artificial neural network and k-nearest neighbor classifiers. Experimental results demonstrate that the SVM approach gives the best performance.
Abstract: One of the most challengeable issues in ESL
(Electronic System Level) design is the lack of a general modeling
scheme for on chip communication architecture. In this paper some
of the mostly used methodologies for modeling and representation of
on chip communication are investigated. Our goal is studying the
existing methods to extract the requirements of a general
representation scheme for communication architecture synthesis. The
next step, will be introducing a modeling and representation method
for being used in automatically synthesis process of on chip
communication architecture.
Abstract: The evolution of current modeling specifications gives rise to the problem of generating automated test cases from a variety of application tools. Past endeavours on behavioural testing of UML statecharts have not systematically leveraged the potential of existing graph theory for testing of objects. Therefore there exists a need for a simple, tool-independent, and effective method for automatic test generation. An architecture, codenamed ACUTE-J (Automated stateChart Unit Testing Engine for Java), for automating the unit test generation process is presented. A sequential approach for converting UML statechart diagrams to JUnit test classes is described, with the application of existing graph theory. Research byproducts such as a universal XML Schema and API for statechart-driven testing are also proposed. The result from a Java implementation of ACUTE-J is discussed in brief. The Chinese Postman algorithm is utilised as an illustration for a run-through of the ACUTE-J architecture.