Abstract: A numerical study has been conducted to investigate the influence of fin pitch and relative humidity on the heat transfer performance of the fin-and-tube heat exchangers having plain fin geometry under dehumidifying conditions. The analysis is done using the ratio between the heat transfer coefficients in totally wet conditions and those in totally dry conditions using the appropriate correlations for both dry and wet conditions. For a constant relative humidity, it is found that the heat transfer coefficient increases with the increase of the air frontal velocity. By contrast, the fin efficiency decreases when the face velocity is increased. Apparently, this phenomenon is attributed to the path of condensate drainage. For the influence of relative humidity, the results showed an increase in heat transfer performance and a decrease in wet fin efficiency when relative humidity increases. This is due to the higher amount of mass transfer encountered at higher relative humidity. However, it is found that the effect of fin pitch on the heat transfer performance depends strongly on the face velocity. At lower frontal velocity the heat transfer increases with fin pitch. Conversely, an increase in fin pitch gives lower heat transfer coefficients when air velocity is increased.
Abstract: This article is presented an experimental and modeling
study of a four-bed pressure swing adsorption process using
zeolite13X to provide oxygen-enriched air. The binary mixture N2/O2
(79/21 vol %) was used as a feed stream. The effects of purge/feed
ratio (P/F), adsorption pressure, cyclic time and product flow rate on
product purity and recovery under nonisothermal condition were
studied. The adsorption dynamics of process were determined using
a mathematical model incorporated mass and energy balances. A
Mathlab code using finite difference method was developed to solve
the set of coupled differential-algebraic equations, and the simulation
results are agreed well with experimental results.
Abstract: Identification of cancer genes that might anticipate
the clinical behaviors from different types of cancer disease is
challenging due to the huge number of genes and small number of
patients samples. The new method is being proposed based on
supervised learning of classification like support vector machines
(SVMs).A new solution is described by the introduction of the
Maximized Margin (MM) in the subset criterion, which permits to
get near the least generalization error rate. In class prediction
problem, gene selection is essential to improve the accuracy and to
identify genes for cancer disease. The performance of the new
method was evaluated with real-world data experiment. It can give
the better accuracy for classification.
Abstract: This paper examines the available experiment data for a copper bromide vapor laser (CuBr laser), emitting at two wavelengths - 510.6 and 578.2nm. Laser output power is estimated based on 10 independent input physical parameters. A classification and regression tree (CART) model is obtained which describes 97% of data. The resulting binary CART tree specifies which input parameters influence considerably each of the classification groups. This allows for a technical assessment that indicates which of these are the most significant for the manufacture and operation of the type of laser under consideration. The predicted values of the laser output power are also obtained depending on classification. This aids the design and development processes considerably.
Abstract: Total weighted tardiness is a measure of customer
satisfaction. Minimizing it represents satisfying the general
requirement of on-time delivery. In this research, we consider an ant
colony optimization (ACO) algorithm to solve the problem of
scheduling unrelated parallel machines to minimize total weighted
tardiness. The problem is NP-hard in the strong sense. Computational
results show that the proposed ACO algorithm is giving promising
results compared to other existing algorithms.
Abstract: Mammalian genomes contain large number of
retroelements (SINEs, LINEs and LTRs) which could affect
expression of protein coding genes through associated transcription
factor binding sites (TFBS). Activity of the retroelement-associated
TFBS in many genes is confirmed experimentally but their global
functional impact remains unclear. Human SINEs (Alu repeats) and
mouse SINEs (B1 and B2 repeats) are known to be clustered in GCrich
gene rich genome segments consistent with the view that they
can contribute to regulation of gene expression. We have shown
earlier that Alu are involved in formation of cis-regulatory modules
(clusters of TFBS) in human promoters, and other authors reported
that Alu located near promoter CpG islands have an increased
frequency of CpG dinucleotides suggesting that these Alu are
undermethylated. Human Alu and mouse B1/B2 elements have an
internal bipartite promoter for RNA polymerase III containing
conserved sequence motif called B-box which can bind basal
transcription complex TFIIIC. It has been recently shown that TFIIIC
binding to B-box leads to formation of a boundary which limits
spread of repressive chromatin modifications in S. pombe. SINEassociated
B-boxes may have similar function but conservation of
TFIIIC binding sites in SINEs located near mammalian promoters
has not been studied earlier. Here we analysed abundance and
distribution of retroelements (SINEs, LINEs and LTRs) in annotated
sequences of the Database of mammalian transcription start sites
(DBTSS). Fractions of SINEs in human and mouse promoters are
slightly lower than in all genome but >40% of human and mouse
promoters contain Alu or B1/B2 elements within -1000 to +200 bp
interval relative to transcription start site (TSS). Most of these SINEs
is associated with distal segments of promoters (-1000 to -200 bp
relative to TSS) indicating that their insertion at distances >200 bp
upstream of TSS is tolerated during evolution. Distribution of SINEs
in promoters correlates negatively with the distribution of CpG
sequences. Using analysis of abundance of 12-mer motifs from the
B1 and Alu consensus sequences in genome and DBTSS it has been
confirmed that some subsegments of Alu and B1 elements are poorly
conserved which depends in part on the presence of CpG
dinucleotides. One of these CpG-containing subsegments in B1
elements overlaps with SINE-associated B-box and it shows better
conservation in DBTSS compared to genomic sequences. It has been
also studied conservation in DBTSS and genome of the B-box
containing segments of old (AluJ, AluS) and young (AluY) Alu
repeats and found that CpG sequence of the B-box of old Alu is
better conserved in DBTSS than in genome. This indicates that Bbox-
associated CpGs in promoters are better protected from
methylation and mutation than B-box-associated CpGs in genomic
SINEs. These results are consistent with the view that potential
TFIIIC binding motifs in SINEs associated with human and mouse
promoters may be functionally important. These motifs may protect
promoters from repressive histone modifications which spread from
adjacent sequences. This can potentially explain well known
clustering of SINEs in GC-rich gene rich genome compartments and
existence of unmethylated CpG islands.
Abstract: In this paper we consider a nonlinear feedback control called augmented automatic choosing control (AACC) for nonlinear systems with constrained input. Constant terms which arise from section wise linearization of a given nonlinear system are treated as coefficients of a stable zero dynamics.Parameters included in the control are suboptimally selectedby extremizing a combination of Hamiltonian and Lyapunov functions with the aid of the genetic algorithm. This approach is applied to a field excitation control problem of power system to demonstrate the splendidness of the AACC. Simulation results show that the new controller can improve performance remarkably well.
Abstract: In this paper, we validate crater detection in moon surface image using FLDA. This proposal assumes that it is applied to SLIM (Smart Lander for Investigating Moon) project aiming at the pin-point landing to the moon surface. The point where the lander should land is judged by the position relations of the craters obtained via camera, so the real-time image processing becomes important element. Besides, in the SLIM project, 400kg-class lander is assumed, therefore, high-performance computers for image processing cannot be equipped. We are studying various crater detection methods such as Haar-Like features, LBP, and PCA. And we think these methods are appropriate to the project, however, to identify the unlearned images obtained by actual is insufficient. In this paper, we examine the crater detection using FLDA, and compare with the conventional methods.
Abstract: This paper proposes an adaptive sliding mode
controller which combines adaptive control and sliding
mode control to control a nonlinear robotic manipulator
with uncertain parameters. We use an adaptive algorithm
based on the concept of sliding mode control to alleviate the
chattering phenomenon of control input. Adaptive laws are
developed to obtain the gain of switching input and the
boundary layer parameters. The stability and convergence
of the robotic manipulator control system are guaranteed
by applying the Lyapunov theorem. Simulation results
demonstrate that the chattering of control input can be
alleviated effectively. The proposed controller scheme can
assure robustness against a large class of uncertainties and
achieve good trajectory tracking performance.
Abstract: Web-based systems have become increasingly
important due to the fact that the Internet and the World Wide Web
have become ubiquitous, surpassing all other technological
developments in our history. The Internet and especially companies
websites has rapidly evolved in their scope and extent of use, from
being a little more than fixed advertising material, i.e. a "web
presences", which had no particular influence for the company's
business, to being one of the most essential parts of the company's
core business.
Traditional software engineering approaches with process models
such as, for example, CMM and Waterfall models, do not work very
well since web system development differs from traditional
development. The development differs in several ways, for example,
there is a large gap between traditional software engineering designs
and concepts and the low-level implementation model, many of the
web based system development activities are business oriented (for
example web application are sales-oriented, web application and
intranets are content-oriented) and not engineering-oriented.
This paper aims to introduce Increment Iterative extreme
Programming (IIXP) methodology for developing web based
systems. In difference to the other existence methodologies, this
methodology is combination of different traditional and modern
software engineering and web engineering principles.
Abstract: We present a preliminary x-ray study on human-hair
microstructures for a health-state indicator, in particular a cancer
case. As an uncomplicated and low-cost method of x-ray technique,
the human-hair microstructure was analyzed by wide-angle x-ray
diffractions (XRD) and small-angle x-ray scattering (SAXS). The
XRD measurements exhibited the simply reflections at the d-spacing
of 28 Å, 9.4 Å and 4.4 Å representing to the periodic distance of the
protein matrix of the human-hair macrofibrous and the diameter and
the repeated spacing of the polypeptide alpha helixes of the
photofibrils of the human-hair microfibrous, respectively. When
compared to the normal cases, the unhealthy cases including to the
breast- and ovarian-cancer cases obtained higher normalized ratios of
the x-ray diffracting peaks of 9.4 Å and 4.4 Å. This likely resulted
from the varied distributions of microstructures by a molecular
alteration. As an elemental analysis by x-ray fluorescence (XRF), the
normalized quantitative ratios of zinc(Zn)/calcium(Ca) and
iron(Fe)/calcium(Ca) were determined. Analogously, both Zn/Ca and
Fe/Ca ratios of the unhealthy cases were obtained higher than both of
the normal cases were. Combining the structural analysis by XRD
measurements and the elemental analysis by XRF measurements
exhibited that the modified fibrous microstructures of hair samples
were in relation to their altered elemental compositions. Therefore,
these microstructural and elemental analyses of hair samples will be
benefit to associate with a diagnosis of cancer and genetic diseases.
This functional method would lower a risk of such diseases by the
early diagnosis. However, the high-intensity x-ray source, the highresolution
x-ray detector, and more hair samples are necessarily
desired to develop this x-ray technique and the efficiency would be
enhanced by including the skin and fingernail samples with the
human-hair analysis.
Abstract: Pure phase gallosilicate nitrite sodalite has been synthesized in a single step by low temperature (373 oK) hydrothermal technique. The product obtained was characterized using a combination of techniques including X-ray powder diffraction, IR, Raman spectroscopy, SEM, MAS NMR spectroscopy as well as thermogravimetry. Sodalite with an ideal composition was obtained after synthesis at 3730K and seven days duration using alkaline medium. The structural features of the Na8[GaSiO4]6(NO2)2 sodalite were investigated by IR, MAS NMR spectroscopy of 29Si and 23Na nuclei and by Reitveld refinement of X-ray powder diffraction data. The crystal structure of this sodalite has been refined in the space group P 4 3n; with a cell parameter 8.98386Å, V= 726.9 Å, (Rwp= 0.077 and Rp=0.0537) and Si-O-Ga angle is found to be 132.920 . MAS NMR study confirms complete ordering of Si and Ga in the gallosilicate framework. The surface area of single entity with stoichiometry Na8[GaSiO4]6(NO2)2 was found to be 8.083 x10-15 cm2/g.
Abstract: In mammalian reproductive tract, the oviduct secretes
huge number of growth factors and cytokines that create an optimal
micro-environment for the initial stages of preimplantation embryos.
Secretion of these growth factors is stage-specific. Among them,
VEGF is a potent mitogen for vascular endothelium and stimulates
vascular permeability. Apart from angiogenesis, VEGF in the oviduct
may be involved in regulating the oocyte maturation and subsequent
developmental process during embryo production in vitro. In
experiment 1, to evaluate the effect of VEGF during IVM of porcine
COC and subsequent developmental ability after PA and SCNT. The
results from these experiments indicated that maturation rates among
the different VEGF concentrations were not significant different. In
experiment 2, total intracellular GSH concentrations of oocytes
matured with VEGF (5-50 ng/ml) were increased significantly
compared to a control and VEGF group (500 ng/ml). In experiment 3,
the blastocyst formation rates and total cell number per blastocyst
after parthenogenesis of oocytes matured with VEGF (5-50 ng/ml)
were increased significantly compared to a control and VEGF group
(500 ng/ml). Similarly, in experiment 4, the blastocyst formation rate
and total cell number per blastocyst after SCNT and IVF of oocytes
matured with VEGF (5 ng/ml) were significantly higher than that of
oocytes matured without VEGF group. In experiment 5, at 10 hour
after the onset of IVF, pronuclear formation rate was evaluated.
Monospermy was significantly higher in VEGF-matured oocytes than
in the control, and polyspermy and sperm penetration per oocyte
were significantly higher in the control group than in the VEGFmatured
oocytes. Supplementation with VEGF during IVM
significantly improved male pronuclear formation as compared with
the control. In experiment 6, type III cortical granule distribution in
oocytes was more common in VEGF-matured oocytes than in the
control. In conclusion, the present study suggested that
supplementation of VEGF during IVM may enhance the
developmental potential of porcine in vitro embryos through increase
of the intracellular GSH level, higher MPN formation and increased
fertilization rate as a consequence of an improved cytoplasmic
maturation.
Abstract: This paper develops a pedometer with a three-axis acceleration sensor that can be placed with any angle. The proposed pedometer measures the number of steps while users walk, jog or run. It can be worn on users’ waistband or placed within pocket or backpack. The work address to improve on the general pedometers, which can only be used in a single direction or can only count of steps without the continuous exercise judgment mechanism. Finally, experimental results confirm the superior performance of the proposed pedometer.
Abstract: The unanticipated destruct of more of the steel moment frames in Northridge earthquake, altered class of regard to the beamto- column connections in moment frames. Panel zone is one the significant part of joints which, it-s stiffness and rigidity has an important effect on the behavior and ductility of the frame. Specifically that behavior of panel zone has a very significant effect on the special moment frames. In this paper , meanwhile the relations for modeling of panel zone in frames are expressed , special moment frames with different spans and stories were studied in the way of performance-based design. The frames designed in according with Iranian steel building code. The effect of panel zone is also considered and in the case of non-existence of performance level, by changing in intimacies and parameter of panel zone, performance level is considered.
Abstract: Objective of this study was to study and compare the effectiveness of inspectors who had different workloads for feed forward and feedback training. The visual search task was simulated to search for specified alphabets called defects. These defects were included of four alphabets in Thai and English such as s ภ, ถ, X, and V with different background. These defects were combined in the specified alphabets and were given the different three backgrounds i.e., Thai, English, and mixed English and Thai alphabets. Sixty students were chosen as a sample in this study and test for final selection subject. Finally, five subjects were taken into testing process. They were asked to search for defects after they were provided basic information. Experiment design was used factorial design and subjects were trained for feed forward and the feedback training. The results show that both trainings were affected on mean search time. It was also found that the feedback training can increase the effectiveness of visual inspectors rather than the feed forward training significantly different at the level of .05
Abstract: The paper presents an on-line recognition machine
(RM) for continuous/isolated, dynamic and static gestures that arise
in Flight Deck Officer (FDO) training. RM is based on generic pattern
recognition framework. Gestures are represented as templates using
summary statistics. The proposed recognition algorithm exploits temporal
and spatial characteristics of gestures via dynamic programming
and Markovian process. The algorithm predicts corresponding index
of incremental input data in the templates in an on-line mode.
Accumulated consistency in the sequence of prediction provides a
similarity measurement (Score) between input data and the templates.
The algorithm provides an intuitive mechanism for automatic detection
of start/end frames of continuous gestures. In the present paper,
we consider isolated gestures. The performance of RM is evaluated
using four datasets - artificial (W TTest), hand motion (Yang) and
FDO (tracker, vision-based ). RM achieves comparable results which
are in agreement with other on-line and off-line algorithms such as
hidden Markov model (HMM) and dynamic time warping (DTW).
The proposed algorithm has the additional advantage of providing
timely feedback for training purposes.
Abstract: The presence of a vertical edge-crack within a web
plate subjected to pure bending induces local compressive stresses
about the crack which may cause tension buckling. Approximate
theoretical expressions were derived for the critical far-field tensile
stress and bending moment capacity of an edge-cracked web plate
associated with tension buckling. These expressions were validated
with finite element analyses and used to investigate the possibility of
tension buckling in web-cracked trial girders. It was found that
tension buckling is an unlikely occurrence unless the web is relatively
thin or the crack is very long.
Abstract: The radius-of-curvature (ROC) defines the degree of
curvature along the centerline of a roadway whereby a travelling
vehicle must follow. Roadway designs must encompass ROC in
mitigating the cost of earthwork associated with construction while
also allowing vehicles to travel at maximum allowable design speeds.
Thus, a road will tend to follow natural topography where possible,
but curvature must also be optimized to permit fast, but safe vehicle
speeds. The more severe the curvature of the road, the slower the
permissible vehicle speed. For route planning, whether for urban
settings, emergency operations, or even parcel delivery, ROC is a
necessary attribute of road arcs for computing travel time.
It is extremely rare for a geo-spatial database to contain ROC. This
paper will present a procedure and mathematical algorithm to
calculate and assign ROC to a segment pair and/or polyline.
Abstract: In this paper, an magnetorheological (MR) mount with
fuzzy sliding mode controller (FSMC) is studied for vibration
suppression when the system is subject to base excitations. In recent
years, magnetorheological fluids are becoming a popular material in
the field of the semi-active control. However, the dynamic equation of
an MR mount is highly nonlinear and it is difficult to identify. FSMC
provides a simple method to achieve vibration attenuation of the
nonlinear system with uncertain disturbances. This method is capable
of handling the chattering problem of sliding mode control effectively
and the fuzzy control rules are obtained by using the Lyapunov
stability theory. The numerical simulations using one-dimension and
two-dimension FSMC show effectiveness of the proposed controller
for vibration suppression. Further, the well-known skyhook control
scheme and an adaptive sliding mode controller are also included in
the simulation for comparison with the proposed FSMC.