Abstract: In this paper a fast motion estimation method for
H.264/AVC named Triplet Search Motion Estimation (TS-ME) is
proposed. Similar to some of the traditional fast motion estimation
methods and their improved proposals which restrict the search points
only to some selected candidates to decrease the computation
complexity, proposed algorithm separate the motion search process to
several steps but with some new features. First, proposed algorithm try
to search the real motion area using proposed triplet patterns instead of
some selected search points to avoid dropping into the local minimum.
Then, in the localized motion area a novel 3-step motion search
algorithm is performed. Proposed search patterns are categorized into
three rings on the basis of the distance from the search center. These
three rings are adaptively selected by referencing the surrounding
motion vectors to early terminate the motion search process. On the
other hand, computation reduction for sub pixel motion search is also
discussed considering the appearance probability of the sub pixel
motion vector. From the simulation results, motion estimation speed
improved by a factor of up to 38 when using proposed algorithm than
that of the reference software of H.264/AVC with ignorable picture
quality loss.
Abstract: This analysis investigates the distortion of flow
measurement and the increase of cavitation along orifice
flowmeter. The analysis using the numerical method (CFD)
validated the distortion of flow measurement through the inlet
velocity profile considering the convergence and grid
dependency. Realizable k-e model was selected and y+ was
about 50 in this numerical analysis. This analysis also estimated
the vulnerability of cavitation effect due to inlet velocity profile.
The investigation concludes that inclined inlet velocity profile
could vary the pressure which was measured at pressure tab
near pipe wall and it led to distort the pressure values ranged
from -3.8% to 5.3% near the orifice plate and to make the
increase of cavitation. The investigation recommends that the
fully developed inlet velocity flow is beneficial to accurate flow
measurement in orifice flowmeter.
Abstract: Physiological control of a left ventricle assist device (LVAD) is generally a complicated task due to diverse operating environments and patient variability. In this work, a tracking control algorithm based on sliding mode and feed forward control for a class of discrete-time single input single output (SISO) nonlinear uncertain systems is presented. The controller was developed to track the reference trajectory to a set operating point without inducing suction in the ventricle. The controller regulates the estimated mean pulsatile flow Qp and mean pulsatility index of pump rotational speed PIω that was generated from a model of the assist device. We recall the principle of the sliding mode control theory then we combine the feed-forward control design with the sliding mode control technique to follow the reference trajectory. The uncertainty is replaced by its upper and lower boundary. The controller was tested in a computer simulation covering two scenarios (preload and ventricular contractility). The simulation results prove the effectiveness and the robustness of the proposed controller
Abstract: In recent five decades, textured yarns of polyester fiber produced by false twist method are the most
important and mass-produced manmade fibers. There are
many parameters of cross section which affect the physical and mechanical properties of textured yarns. These parameters
are surface area, perimeter, equivalent diameter, large
diameter, small diameter, convexity, stiffness, eccentricity, and hydraulic diameter. These parameters were evaluated by
digital image processing techniques. To find trends between production criteria and evaluated parameters of cross section, three criteria of production line have been adjusted and different types of yarns were produced. These criteria are
temperature, drafting ratio, and D/Y ratio. Finally the relations between production criteria and cross section parameters were
considered. The results showed that the presented technique can recognize and measure the parameters of fiber cross section in acceptable accuracy. Also, the optimum condition
of adjustments has been estimated from results of image analysis evaluation.
Abstract: A novel low-cost impedance control structure is
proposed for monitoring the contact force between end-effector and
environment without installing an expensive force/torque sensor.
Theoretically, the end-effector contact force can be estimated from the
superposition of each joint control torque. There have a nonlinear
matrix mapping function between each joint motor control input and
end-effector actuating force/torques vector. This new force control
structure can be implemented based on this estimated mapping matrix.
First, the robot end-effector is manipulated to specified positions, then
the force controller is actuated based on the hall sensor current
feedback of each joint motor. The model-free fuzzy sliding mode
control (FSMC) strategy is employed to design the position and force
controllers, respectively. All the hardware circuits and software
control programs are designed on an Altera Nios II embedded
development kit to constitute an embedded system structure for a
retrofitted Mitsubishi 5 DOF robot. Experimental results show that PI
and FSMC force control algorithms can achieve reasonable contact
force monitoring objective based on this hardware control structure.
Abstract: This paper presents a novel method for remaining
useful life prediction using the Elliptical Basis Function (EBF)
network and a Markov chain. The EBF structure is trained by a
modified Expectation-Maximization (EM) algorithm in order to take
into account the missing covariate set. No explicit extrapolation is
needed for internal covariates while a Markov chain is constructed to
represent the evolution of external covariates in the study. The
estimated external and the unknown internal covariates constitute an
incomplete covariate set which are then used and analyzed by the EBF
network to provide survival information of the asset. It is shown in the
case study that the method slightly underestimates the remaining
useful life of an asset which is a desirable result for early maintenance
decision and resource planning.
Abstract: This paper presents the methodology from machine
learning approaches for short-term rain forecasting system. Decision
Tree, Artificial Neural Network (ANN), and Support Vector Machine
(SVM) were applied to develop classification and prediction models
for rainfall forecasts. The goals of this presentation are to
demonstrate (1) how feature selection can be used to identify the
relationships between rainfall occurrences and other weather
conditions and (2) what models can be developed and deployed for
predicting the accurate rainfall estimates to support the decisions to
launch the cloud seeding operations in the northeastern part of
Thailand. Datasets collected during 2004-2006 from the
Chalermprakiat Royal Rain Making Research Center at Hua Hin,
Prachuap Khiri khan, the Chalermprakiat Royal Rain Making
Research Center at Pimai, Nakhon Ratchasima and Thai
Meteorological Department (TMD). A total of 179 records with 57
features was merged and matched by unique date. There are three
main parts in this work. Firstly, a decision tree induction algorithm
(C4.5) was used to classify the rain status into either rain or no-rain.
The overall accuracy of classification tree achieves 94.41% with the
five-fold cross validation. The C4.5 algorithm was also used to
classify the rain amount into three classes as no-rain (0-0.1 mm.),
few-rain (0.1- 10 mm.), and moderate-rain (>10 mm.) and the overall
accuracy of classification tree achieves 62.57%. Secondly, an ANN
was applied to predict the rainfall amount and the root mean square
error (RMSE) were used to measure the training and testing errors of
the ANN. It is found that the ANN yields a lower RMSE at 0.171 for
daily rainfall estimates, when compared to next-day and next-2-day
estimation. Thirdly, the ANN and SVM techniques were also used to
classify the rain amount into three classes as no-rain, few-rain, and
moderate-rain as above. The results achieved in 68.15% and 69.10%
of overall accuracy of same-day prediction for the ANN and SVM
models, respectively. The obtained results illustrated the comparison
of the predictive power of different methods for rainfall estimation.
Abstract: This paper presents a novel template-based method to
detect objects of interest from real images by shape matching. To
locate a target object that has a similar shape to a given template
boundary, the proposed method integrates three components: contour
grouping, partial shape matching, and boundary verification. In the
first component, low-level image features, including edges and
corners, are grouped into a set of perceptually salient closed contours
using an extended ratio-contour algorithm. In the second component,
we develop a partial shape matching algorithm to identify the
fractions of detected contours that partly match given template
boundaries. Specifically, we represent template boundaries and
detected contours using landmarks, and apply a greedy algorithm to
search the matched landmark subsequences. For each matched
fraction between a template and a detected contour, we estimate an
affine transform that transforms the whole template into a hypothetic
boundary. In the third component, we provide an efficient algorithm
based on oriented edge lists to determine the target boundary from
the hypothetic boundaries by checking each of them against image
edges. We evaluate the proposed method on recognizing and
localizing 12 template leaves in a data set of real images with clutter
back-grounds, illumination variations, occlusions, and image noises.
The experiments demonstrate the high performance of our proposed
method1.
Abstract: This paper presents a method to estimate load profile
in a multiple power flow solutions for every minutes in 24 hours per
day. A method to calculate multiple solutions of non linear profile is
introduced. The Power System Simulation/Engineering (PSS®E) and
python has been used to solve the load power flow. The result of this
power flow solutions has been used to estimate the load profiles for
each load at buses using Independent Component Analysis (ICA)
without any knowledge of parameter and network topology of the
systems. The proposed algorithm is tested with IEEE 69 test bus
system represents for distribution part and the method of ICA has
been programmed in MATLAB R2012b version. Simulation results
and errors of estimations are discussed in this paper.
Abstract: This paper introduces an intelligent system, which can be applied in the monitoring of vehicle speed using a single camera. The ability of motion tracking is extremely useful in many automation problems and the solution to this problem will open up many future applications. One of the most common problems in our daily life is the speed detection of vehicles on a highway. In this paper, a novel technique is developed to track multiple moving objects with their speeds being estimated using a sequence of video frames. Field test has been conducted to capture real-life data and the processed results were presented. Multiple object problems and noisy in data are also considered. Implementing this system in real-time is straightforward. The proposal can accurately evaluate the position and the orientation of moving objects in real-time. The transformations and calibration between the 2D image and the actual road are also considered.
Abstract: In this paper, numerical solution for the generalized Rosenau-Burgers equation is considered and Crank-Nicolson finite difference scheme is proposed. Existence of the solutions for the difference scheme has been shown. Stability, convergence and priori error estimate of the scheme are proved. Numerical results demonstrate that the scheme is efficient and reliable.
Abstract: This paper introduces a technique for simulating a
single-server exponential queuing system. The technique called the
Q-Simulator is a computer program which can simulate the effect of
traffic intensity on all system average quantities given the arrival
and/or service rates. The Q-Simulator has three phases namely: the
formula based method, the uncontrolled simulation, and the
controlled simulation. The Q-Simulator generates graphs (crystal
solutions) for all results of the simulation or calculation and can be
used to estimate desirable average quantities such as waiting times,
queue lengths, etc.
Abstract: The recent development of Information and Communication Technology (ICT) enables new ways of "democratic" decision-making such as a page-ranking system, which estimates the importance of a web page based on indirect trust on that page shared by diverse group of unorganized individuals. These kinds of "democracy" have not been acclaimed yet in the world of real politics. On the other hand, a large amount of data about personal relations including trust, norms of reciprocity, and networks of civic engagement has been accumulated in a computer-readable form by computer systems (e.g., social networking systems). We can use these relations as a new type of social capital to construct a new democratic decision-making system based on a delegation network. In this paper, we propose an effective decision-making support system, which is based on empowering someone's vote whom you trust. For this purpose, we propose two new techniques: the first is for estimating entire vote distribution from a small number of votes, and the second is for estimating active voter choice to promote voting using a delegation network. We show that these techniques could increase the voting ratio and credibility of the whole decision by agent-based simulations.
Abstract: Martingale model diagnostic for assessing the fit of logistic regression model to recurrent events data are studied. One way of assessing the fit is by plotting the empirical standard deviation of the standardized martingale residual processes. Here we used another diagnostic plot based on martingale residual covariance. We investigated the plot performance under several types of model misspecification. Clearly the method has correctly picked up the wrong model. Also we present a test statistic that supplement the inspection of the two diagnostic. The test statistic power agrees with what we have seen in the plots of the estimated martingale covariance.
Abstract: This paper presents probabilistic horizontal seismic
hazard assessment of Naghan, Iran. It displays the probabilistic
estimate of Peak Ground Horizontal Acceleration (PGHA) for the
return period of 475, 950 and 2475 years. The output of the
probabilistic seismic hazard analysis is based on peak ground
acceleration (PGA), which is the most common criterion in designing
of buildings. A catalogue of seismic events that includes both
historical and instrumental events was developed and covers the
period from 840 to 2009. The seismic sources that affect the hazard
in Naghan were identified within the radius of 200 km and the
recurrence relationships of these sources were generated by Kijko
and Sellevoll. Finally Peak Ground Horizontal Acceleration (PGHA)
has been prepared to indicate the earthquake hazard of Naghan for
different hazard levels by using SEISRISK III software.
Abstract: A new distance-adjusted approach is proposed in
which static square contours are defined around an estimated
symbol in a QAM constellation, which create regions that
correspond to fixed step sizes and weighting factors. As a
result, the equalizer tap adjustment consists of a linearly
weighted sum of adaptation criteria that is scaled by a variable
step size. This approach is the basis of two new algorithms: the
Variable step size Square Contour Algorithm (VSCA) and the
Variable step size Square Contour Decision-Directed
Algorithm (VSDA). The proposed schemes are compared with
existing blind equalization algorithms in the SCA family in
terms of convergence speed, constellation eye opening and
residual ISI suppression. Simulation results for 64-QAM
signaling over empirically derived microwave radio channels
confirm the efficacy of the proposed algorithms. An RTL
implementation of the blind adaptive equalizer based on the
proposed schemes is presented and the system is configured to
operate in VSCA error signal mode, for square QAM signals
up to 64-QAM.
Abstract: Many supervised induction algorithms require discrete
data, even while real data often comes in a discrete
and continuous formats. Quality discretization of continuous
attributes is an important problem that has effects on speed,
accuracy and understandability of the induction models. Usually,
discretization and other types of statistical processes are applied
to subsets of the population as the entire population is practically
inaccessible. For this reason we argue that the discretization
performed on a sample of the population is only an estimate of
the entire population. Most of the existing discretization methods,
partition the attribute range into two or several intervals using
a single or a set of cut points. In this paper, we introduce a
technique by using resampling (such as bootstrap) to generate
a set of candidate discretization points and thus, improving the
discretization quality by providing a better estimation towards
the entire population. Thus, the goal of this paper is to observe
whether the resampling technique can lead to better discretization
points, which opens up a new paradigm to construction of
soft decision trees.
Abstract: The Chiu-s method which generates a Takagi-Sugeno Fuzzy Inference System (FIS) is a method of fuzzy rules extraction. The rules output is a linear function of inputs. In addition, these rules are not explicit for the expert. In this paper, we develop a method which generates Mamdani FIS, where the rules output is fuzzy. The method proceeds in two steps: first, it uses the subtractive clustering principle to estimate both the number of clusters and the initial locations of a cluster centers. Each obtained cluster corresponds to a Mamdani fuzzy rule. Then, it optimizes the fuzzy model parameters by applying a genetic algorithm. This method is illustrated on a traffic network management application. We suggest also a Mamdani fuzzy rules generation method, where the expert wants to classify the output variables in some fuzzy predefined classes.
Abstract: This paper describes the two stage control using a disturbance observer and a Kalman filter. The system feedback uses the estimated state when it controls the speed. After the change-over point, its feedback uses the controlled plant output when it controls the position. To change the system continually, a change-over point has to be determined pertinently, and the controlled plant input has to be adjusted by the addition of the appropriate value. The proposed method has noise-reduction effect. It changes the system continually, even if the controlled plant identification has the error. Although the conventional method needs a speed sensor, the proposed method does not need it. The proposed method has a superior robustness compared with the conventional two stage control.
Abstract: Availability and mobilization of revenue is the main
essential with which an economy is managed and run. While
planning or while making the budgets nations set revenue targets to
be achieved. But later when the accounts are closed the actual
collections of revenue through taxes or even the non-tax revenue
collection would invariably be different as compared to the initial
estimates and targets set to be achieved. This revenue-gap distorts the
whole system and the economy disturbing all the major macroeconomic
indicators. This study is aimed to find out short and long
term impact of revenue gap on budget deficit, debt burden and
economic growth on the economy of Pakistan. For this purpose the
study uses autoregressive distributed lag approach to cointegration
and error correction mechanism on three different models for the
period 1980 to 2009. The empirical results show that revenue gap has
a short and long run relationship with economic growth and budget
deficit. However, revenue gap has no impact on debt burden.