Abstract: IMCS is Integrated Monitoring and Control System for
thermal power plant. This system consists of mainly two parts; controllers and OIS (Operator Interface System). These two parts are
connected by Ethernet-based communication. The controller side of communication is managed by CNet module and OIS side is managed
by data server of OIS. CNet module sends the data of controller to data
server and receives commend data from data server. To minimizes or
balance the load of data server, this module buffers data created by controller at every cycle and send buffered data to data server on request of data server. For multiple data server, this module manages
the connection line with each data server and response for each request
from multiple data server. CNet module is included in each controller
of redundant system. When controller fail-over happens on redundant system, this module can provide data of controller to data sever
without loss. This paper presents three main features – separation of get task, usage of ring buffer and monitoring communication status –of CNet module to carry out these functions.
Abstract: This study investigates the electrical performance of a
planar solid oxide fuel cell unit with cross-flow configuration when the fuel utilization gets higher and the fuel inlet flow are non-uniform.
A software package in this study solves two-dimensional,
simultaneous, partial differential equations of mass, energy, and
electro-chemistry, without considering stack direction variation. The
results show that the fuel utilization increases with a decrease in the molar flow rate, and the average current density decreases when the
molar flow rate drops. In addition, non-uniform Pattern A will induce more severe happening of non-reaction area in the corner of the fuel
exit and the air inlet. This non-reaction area deteriorates the average
current density and then deteriorates the electrical performance to –7%.
Abstract: The value of overall oxygen transfer Coefficient
(KLa), which is the best measure of oxygen transfer in water through
aeration, is obtained by a simple approach, which sufficiently
explains the utility of the method to eliminate the discrepancies due
to inaccurate assumption of saturation dissolved oxygen
concentration. The rate of oxygen transfer depends on number of
factors like intensity of turbulence, which in turns depends on the
speed of rotation, size, and number of blades, diameter and
immersion depth of the rotor, and size and shape of aeration tank, as
well as on physical, chemical, and biological characteristic of water.
An attempt is made in this paper to correlate the overall oxygen
transfer Coefficient (KLa), as an independent parameter with other
influencing parameters mentioned above. It has been estimated that
the simulation equation developed predicts the values of KLa and
power with an average standard error of estimation of 0.0164 and
7.66 respectively and with R2 values of 0.979 and 0.989 respectively,
when compared with experimentally determined values. The
comparison of this model is done with the model generated using
Computational fluid dynamics (CFD) and both the models were
found to be in good agreement with each other.
Abstract: The paper outlines the relevance of computational
geometry within the design and production process of architecture.
Based on two case studies, the digital chain - from the initial formfinding
to the final realization of spatial concepts - is discussed in
relation to geometric principles. The association with the fascinating
complexity that can be found in nature and its underlying geometry
was the starting point for both projects presented in the paper. The
translation of abstract geometric principles into a three-dimensional
digital design model – realized in Rhinoceros – was followed by a
process of transformation and optimization of the initial shape that
integrated aesthetic, spatial and structural qualities as well as aspects
of material properties and conditions of production.
Abstract: We studied the evolution of elliptic heavy SF6
gas cylinder surrounded by air when accelerated by a planar
Mach 1.25 shock. A multiple dynamics imaging technology has
been used to obtain one image of the experimental initial
conditions and five images of the time evolution of elliptic
cylinder. We compared the width and height of the circular and
two kinds of elliptic gas cylinders, and analyzed the vortex
strength of the elliptic ones. Simulations are in very good
agreement with the experiments, but due to the different initial
gas cylinder shapes, a certain difference of the initial density
peak and distribution exists between the circular and elliptic
gas cylinders, and the latter initial state is more sensitive and
more inenarrable.
Abstract: Smoothing or filtering of data is first preprocessing step
for noise suppression in many applications involving data analysis.
Moving average is the most popular method of smoothing the data,
generalization of this led to the development of Savitzky-Golay filter.
Many window smoothing methods were developed by convolving
the data with different window functions for different applications;
most widely used window functions are Gaussian or Kaiser. Function
approximation of the data by polynomial regression or Fourier
expansion or wavelet expansion also gives a smoothed data. Wavelets
also smooth the data to great extent by thresholding the wavelet
coefficients. Almost all smoothing methods destroys the peaks and
flatten them when the support of the window is increased. In certain
applications it is desirable to retain peaks while smoothing the data
as much as possible. In this paper we present a methodology called
as peak-wise smoothing that will smooth the data to any desired level
without losing the major peak features.
Abstract: Antimosy-doped tin oxide (ATO) particles were
prepared via chemical coprecipitation and reverse emulsion. The size
and size distribution of ATO particles were obviously decreased via
reverse microemulsion method. At the relatively high yield the ATO
particles were nearly spherical in shape, meanwhile the crystalline
structure and excellent conductivity were reserved, which could satisfy
the requirement as composite fillers, such as dielectric filler of
polyimide film.
Abstract: The utilization of cheese whey as a fermentation
substrate to produce bio-ethanol is an effort to supply bio-ethanol
demand as a renewable energy. Like other process systems, modeling
is also required for fermentation process design, optimization and
plant operation. This research aims to study the fermentation process
of cheese whey by applying mathematics and fundamental concept in
chemical engineering, and to investigate the characteristic of the
cheese whey fermentation process. Steady state simulation results for
inlet substrate concentration of 50, 100 and 150 g/l, and various
values of hydraulic retention time, showed that the ethanol
productivity maximum values were 0.1091, 0.3163 and 0.5639 g/l.h
respectively. Those values were achieved at hydraulic retention time
of 20 hours, which was the minimum value used in this modeling.
This showed that operating reactor at low hydraulic retention time
was favorable. Model of bio-ethanol production from cheese whey
will enhance the understanding of what really happen in the
fermentation process.
Abstract: This paper proposes a hybrid method for eyes localization
in facial images. The novelty is in combining techniques
that utilise colour, edge and illumination cues to improve accuracy.
The method is based on the observation that eye regions have dark
colour, high density of edges and low illumination as compared
to other parts of face. The first step in the method is to extract
connected regions from facial images using colour, edge density and
illumination cues separately. Some of the regions are then removed
by applying rules that are based on the general geometry and shape
of eyes. The remaining connected regions obtained through these
three cues are then combined in a systematic way to enhance the
identification of the candidate regions for the eyes. The geometry
and shape based rules are then applied again to further remove the
false eye regions. The proposed method was tested using images from
the PICS facial images database. The proposed method has 93.7%
and 87% accuracies for initial blobs extraction and final eye detection
respectively.
Abstract: Carbon disulfide is widely used for the production of
viscose rayon, rubber, and other organic materials and it is a
feedstock for the synthesis of sulfuric acid. The objective of this
paper is to analyze possibilities for efficient production of CS2 from
sour natural gas reformation (H2SMR) (2H2S+CH4 =CS2 +4H2) .
Also, the effect of H2S to CH4 feed ratio and reaction temperature on
carbon disulfide production is investigated numerically in a
reforming reactor. The chemical reaction model is based on an
assumed Probability Density Function (PDF) parameterized by the
mean and variance of mixture fraction and β-PDF shape. The results
show that the major factors influencing CS2 production are reactor
temperature. The yield of carbon disulfide increases with increasing
H2S to CH4 feed gas ratio (H2S/CH4≤4). Also the yield of C(s)
increases with increasing temperature until the temperature reaches
to 1000°K, and then due to increase of CS2 production and
consumption of C(s), yield of C(s) drops with further increase in the
temperature. The predicted CH4 and H2S conversion and yield of
carbon disulfide are in good agreement with result of Huang and TRaissi.
Abstract: The primary purpose of this article is an attempt to
find the implication of globalization on education. Globalization has
an important role as a process in the economical, political, cultural
and technological dimensions in the life of the contemporary human
being and has been affected by it. Education has its effects in this
procedure and while influencing it through educating global citizens
having universal human features and characteristics, has been
influenced by this phenomenon too. Nowadays, the role of education
is not just to develop in the students the knowledge and skills
necessary for the new kinds of jobs. If education wants to help
students be prepared of the new global society, it has to make them
engaged productive and critical citizens for the global era, so that
they can reflect about their roles as key actors in a dynamic often
uneven, matrix of economic and cultural exchanges. If education
wants to reinforce and raise the national identity, the value system
and the children and teenagers, it should make them ready for living
in the global era of this century. The used method in this research is
documentary and analyzing the documents. Studies in this field show
globalization has influences on the processes of the production,
distribution and consuming of knowledge. The happening of this
event in the information era has not only provide the necessary
opportunities for the exchanges of education worldwide but also has
privileges for the developing countries which enables them to
strengthen educational bases of their society and have an important
step toward their future.
Abstract: In the present work steady inviscid hypersonic flows
are calculated by approximate Method. Maslens' inverse method is the chosen approximate method. For the inverse problem, parabolic
shock shape is chosen for the two-dimensional flow, and the body shape and flow field are calculated using Maslen's method. For the axisymmetric inverse problem paraboloidal shock is chosen and the
surface distribution of pressure is obtained.
Abstract: The three-time-scale plant model of a wind power
generator, including a wind turbine, a flexible vertical shaft, a Variable
Inertia Flywheel (VIF) module, an Active Magnetic Bearing (AMB)
unit and the applied wind sequence, is constructed. In order to make
the wind power generator be still able to operate as the spindle speed
exceeds its rated speed, the VIF is equipped so that the spindle speed
can be appropriately slowed down once any stronger wind field is
exerted. To prevent any potential damage due to collision by shaft
against conventional bearings, the AMB unit is proposed to regulate
the shaft position deviation. By singular perturbation order-reduction
technique, a lower-order plant model can be established for the
synthesis of feedback controller. Two major system parameter
uncertainties, an additive uncertainty and a multiplicative uncertainty,
are constituted by the wind turbine and the VIF respectively.
Frequency Shaping Sliding Mode Control (FSSMC) loop is proposed
to account for these uncertainties and suppress the unmodeled
higher-order plant dynamics. At last, the efficacy of the FSSMC is
verified by intensive computer and experimental simulations for
regulation on position deviation of the shaft and counter-balance of
unpredictable wind disturbance.
Abstract: The principal focus of this study is on the
measurement and analysis of labor learnings in Pakistan. The study
at the aggregate economy level focus on the labor productivity
movements and at large-scale manufacturing level focus on the cost
structure, with isolating the contribution of the learning curve. The
analysis of S-shaped curve suggests that learnings are only below one
half of aggregate learning curve and other half shows the retardation
in learning, hence retardation in productivity movements. The study
implies the existence of learning economies in term of cost reduction
that is input cost per unit produced decreases by 0.51 percent every
time the cumulative production output doubles.
Abstract: A numerical method is developed for simulating
the motion of particles with arbitrary shapes in an effectively
infinite or bounded viscous flow. The particle translational and
angular motions are numerically investigated using a fluid-structure
interaction (FSI) method based on the Arbitrary-Lagrangian-Eulerian
(ALE) approach and the dynamic mesh method (smoothing and
remeshing) in FLUENT ( ANSYS Inc., USA). Also, the effects of
arbitrary shapes on the dynamics are studied using the FSI method
which could be applied to the motions and deformations of a single
blood cell and multiple blood cells, and the primary thrombogenesis
caused by platelet aggregation. It is expected that, combined with a
sophisticated large-scale computational technique, the simulation
method will be useful for understanding the overall properties of blood
flow from blood cellular level (microscopic) to the resulting
rheological properties of blood as a mass (macroscopic).
Abstract: A new design of a planar passive T-micromixer with fin-shaped baffles in the mixing channel is presented. The mixing efficiency and the level of pressure loss in the channel have been investigated by numerical simulations in the range of Reynolds number (Re) 1 to 50. A Mixing index (Mi) has been defined to quantify the mixing efficiency, which results over 85% at both ends of the Re range, what demonstrates the micromixer can enhance mixing using the mechanisms of diffusion (lower Re) and convection (higher Re). Three geometric dimensions: radius of baffle, baffles pitch and height of the channel define the design parameters, and the mixing index and pressure loss are the performance parameters used to optimize the micromixer geometry with a multi-criteria optimization method. The Pareto front of designs with the optimum trade-offs, maximum mixing index with minimum pressure loss, is obtained. Experiments for qualitative and quantitative validation have been implemented.
Abstract: Disordered function of maniphalanx and difficulty with
ambulation will occur insofar as a human has a failure in the spinal
marrow. Cervical spondylotic myelopathy as one of the myelopathy
emanates from not only external factors but also increased age. In
addition, the diacrisis is difficult since cervical spondylotic
myelopathy is evaluated by a doctor-s neurological remark and
imaging findings. As a quantitative method for measuring the degree
of disability, hand-operated triangle step test (for short, TST) has
formulated. In this research, a full automatic triangle step counter
apparatus is designed and developed to measure the degree of
disability in an accurate fashion according to the principle of TST. The
step counter apparatus whose shape is a low triangle pole displays the
number of stepping upon each corner. Furthermore, the apparatus has
two modes of operation. Namely, one is for measuring the degree of
disability and the other for rehabilitation exercise. In terms of
usefulness, clinical practice should be executed before too long.
Abstract: The operation performance of a valveless micro-pump
is strongly dependent on the shape of connected nozzle/diffuser and
Reynolds number. The aims of present work are to compare the
performance curves of micropump with the original straight
nozzle/diffuser and contoured nozzle/diffuser under different back
pressure conditions. The tested valveless micropumps are assembled
of five pieces of patterned PMMA plates with hot-embracing
technique. The structures of central chamber, the inlet/outlet
reservoirs and the connected nozzle/diffuser are fabricated with laser
cutting machine. The micropump is actuated with circular-type PZT
film embraced on the bottom of central chamber. The deformation of
PZT membrane with various input voltages is measured with a
displacement laser probe. A simple testing facility is also constructed
to evaluate the performance curves for comparison.
In order to observe the evaluation of low Reynolds number
multiple vortex flow patterns within the micropump during suction
and pumping modes, the unsteady, incompressible laminar
three-dimensional Reynolds-averaged Navier-Stokes equations are
solved. The working fluid is DI water with constant thermo-physical
properties. The oscillating behavior of PZT film is modeled with the
moving boundary wall in way of UDF program. With the dynamic
mesh method, the instants pressure and velocity fields are obtained
and discussed.Results indicated that the volume flow rate is not
monotony increased with the oscillating frequency of PZT film,
regardless of the shapes of nozzle/diffuser. The present micropump
can generate the maximum volume flow rate of 13.53 ml/min when
the operation frequency is 64Hz and the input voltage is 140 volts.
The micropump with contoured nozzle/diffuser can provide 7ml/min
flow rate even when the back pressure is up to 400 mm-H2O. CFD
results revealed that the flow central chamber was occupied with
multiple pairs of counter-rotating vortices during suction and
pumping modes. The net volume flow rate over a complete
oscillating periodic of PZT
Abstract: Small cracks or chips of a product appear very
frequently in the course of continuous production of an automatic
press process system. These phenomena become the cause of not only
defective product but also damage of a press mold. In order to solve
this problem AE system was introduced. AE system was expected to
be very effective to real time detection of the defective product and to
prevention of the damage of the press molds.
In this study, for pick and analysis of AE signals generated from the
press process, AE sensors/pre-amplifier/analysis and processing board
were used as frequently found in the other similar cases. For analysis
and processing the AE signals picked in real time from the good or bad
products, specialized software called cdm8 was used. As a result of
this work it was conformed that intensity and shape of the various AE
signals differ depending on the weight and thickness of metal sheet
and process type.
Abstract: The main objective of this paper is to contribute the
existing knowledge transfer and IT Outsourcing literature
specifically in the context of Malaysia by reviewing the current
practices of e-government IT outsourcing in Malaysia including the
issues and challenges faced by the public agencies in transferring the
knowledge during the engagement. This paper discusses various
factors and different theoretical model of knowledge transfer starting
from the traditional model to the recent model suggested by the
scholars. The present paper attempts to align organizational
knowledge from the knowledge-based view (KBV) and
organizational learning (OL) lens. This review could help shape the
direction of both future theoretical and empirical studies on inter-firm
knowledge transfer specifically on how KBV and OL perspectives
could play significant role in explaining the complex relationships
between the client and vendor in inter-firm knowledge transfer and
the role of organizational management information system and
Transactive Memory System (TMS) to facilitate the organizational
knowledge transferring process. Conclusion is drawn and further
research is suggested.