Abstract: This paper study the segmented split capacitor
Digital-to-Analog Converter (DAC) implemented in a differentialtype
12-bit Successive Approximation Analog-to-Digital Converter
(SA-ADC). The series capacitance split array method employed as it
reduced the total area of the capacitors required for high resolution
DACs. A 12-bit regular binary array structure requires 2049 unit
capacitors (Cs) while the split array needs 127 unit Cs. These results
in the reduction of the total capacitance and power consumption of
the series split array architectures as to regular binary-weighted
structures. The paper will show the 12-bit DAC series split capacitor
with 4-bit thermometer coded DAC architectures as well as the
simulation and measured results.
Abstract: While OCD is one of the most commonly occurring
psychiatric conditions experienced by older adults, there is a paucity
of research conducted into the treatment of older adults with OCD.
This case study represents the first published investigation of a
cognitive treatment for geriatric OCD. It describes the successful
treatment of an 86-year old man with a 63-year history of OCD using
Danger Ideation Reduction Therapy (DIRT). The client received 14
individual, 50-minute treatment sessions of DIRT over 13 weeks.
Clinician-based Y-BOCS scores reduced 84% from 25 (severe) at
pre-treatment, to 4 (subclinical) at 6-month post-treatment follow-up
interview, demonstrating the efficacy of DIRT for this client. DIRT
may have particular advantages over ERP and pharmacological
approaches, however further research is required in older adults with
OCD.
Abstract: Kish Islands in South of Iran is located in coastal
water near Hormozgan Province. Based on the wind 3-hour statistics
in Kish station, the mean annual windspeed in this Island is 8.6 knot
(4.3 m/s). The maximum windspeed recorded in this stations 47 knot
(23.5 m/s). In 45.7 percent of recorded times, windspeed has been
Zero or less than 8 knot which is not suitable to use the wind energy.
But in 54.3 percent of recorded times, windspeed has been more than
8 knot and suitable to use wind energy to run turbines. In 40.2
percent of recorded times, windspeed has been between 8 to 16 knot,
in 13 percent of times between 16 to 24 knot and in 1 percent of
times it has been higher than 24 knot. In this station, the direction of
winds higher than 8 is west and wind direction in Kish station is
stable in most times of the year.With regard to high – speed and
stable direction winds during the year and also shallow coasts near
this is land, it is possible to build offshore wind farms near Kish
Island and utilize wind energy produce the electricity required in this
Island during most of the year.
Abstract: As privacy becomes a major concern for consumers
and enterprises, many research have been focused on the privacy
protecting technology in recent years. In this paper, we present a
comprehensive approach for usage access control based on the notion
purpose. In our model, purpose information associated with a given
data element specifies the intended use of the subjects and objects in
the usage access control model. A key feature of our model is that it
allows when an access is required, the access purpose is checked
against the intended purposes for the data item. We propose an
approach to represent purpose information to support access control
based on purpose information. Our proposed solution relies on usage
access control (UAC) models as well as the components which based
on the notions of the purpose information used in subjects and
objects. Finally, comparisons with related works are analyzed.
Abstract: Mental health professionals views about mental illness
is an important issue which has not received enough attention. The
negative stigma associated with mental illness can have many
negative consequences. Unfortunately, health professionals working
with the mentally ill can also exhibit stigma. It has been suggested
that causal explanations or beliefs around the causes of mental illness
may influence stigma. This study aims to gain a greater insight into
stigma through examining stigma among potential mental health
professionals. Firstly, results found that potential mental health
professionals had relatively low social distance t(205) = -3.62, p
Abstract: A new numerical method for solving the twodimensional,
steady, incompressible, viscous flow equations on a
Curvilinear staggered grid is presented in this paper. The proposed
methodology is finite difference based, but essentially takes
advantage of the best features of two well-established numerical
formulations, the finite difference and finite volume methods. Some
weaknesses of the finite difference approach are removed by
exploiting the strengths of the finite volume method. In particular,
the issue of velocity-pressure coupling is dealt with in the proposed
finite difference formulation by developing a pressure correction
equation in a manner similar to the SIMPLE approach commonly
used in finite volume formulations. However, since this is purely a
finite difference formulation, numerical approximation of fluxes is
not required. Results obtained from the present method are based on
the first-order upwind scheme for the convective terms, but the
methodology can easily be modified to accommodate higher order
differencing schemes.
Abstract: A Negotiation Support is required on a value-based decision to enable each stakeholder to evaluate and rank the solution alternatives before engaging into negotiation with the other stakeholders. This study demonstrates a process of negotiation support model for selection of a building system from value-based design perspective. The perspective is based on comparison of function and cost of a building system. Multi criteria decision techniques were applied to determine the relative value of the alternative solutions for performing the function. A satisfying option game theory are applied to the criteria of value-based decision which are LCC (life cycle cost) and function based FAST. The results demonstrate a negotiation process to select priorities of a building system. The support model can be extended to an automated negotiation by combining value based decision method, group decision and negotiation support.
Abstract: There is a complex situation on the transport environment in the cities of the world. For the analysis and prevention of environmental problems an accurate calculation hazardous substances concentrations at each point of the investigated area is required. In the turbulent atmosphere of the city the wellknown methods of mathematical statistics for these tasks cannot be applied with a satisfactory level of accuracy. Therefore, to solve this class of problems apparatus of mathematical physics is more appropriate. In such models, because of the difficulty as a rule the influence of uneven land surface on streams of air masses in the turbulent atmosphere of the city are not taken into account. In this paper the influence of the surface roughness, which can be quite large, is mathematically shown. The analysis of this problem under certain conditions identified the possibility of areas appearing in the atmosphere with pressure tending to infinity, i.e. so-called "wall effect".
Abstract: A method has been developed for preparing load
models for power flow and stability. The load modeling
(LOADMOD) computer software transforms data on load class mix,
composition, and characteristics into the from required for
commonly–used power flow and transient stability simulation
programs. Typical default data have been developed for load
composition and characteristics. This paper defines LOADMOD
software and describes the dynamic and static load modeling
techniques used in this software and results of initial testing for
BAKHTAR power system.
Abstract: There has been gradual progress of late in construction projects, particularly in big-scale megaprojects. Due to the long-term construction period, however, with large-scale budget investment, lack of construction management technologies, and increase in the incomplete elements of project schedule management, a plan to conduct efficient operations and to ensure business safety is required. In particular, as the project management information system (PMIS) is meant for managing a single project centering on the construction phase, there is a limitation in the management of program-scale businesses like megaprojects. Thus, a program management information system (PgMIS) that includes program-level management technologies is needed to manage multiple projects. In this study, a support tool was developed for managing the cost and schedule information occurring in the construction phase, at the program level. In addition, a case study on the developed support tool was conducted to verify the usability of the system. With the use of the developed support tool program, construction managers can monitor the progress of the entire project and of the individual subprojects in real time.
Abstract: This article is based on the technique which is called
Discrete Parameter Tracking (DPT). First introduced by A. A. Azab
[8] which is applicable for less order reference model. The order of
the reference model is (n-l) and n is the number of the adjustable
parameters in the physical plant.
The technique utilizes a modified gradient method [9] where the
knowledge of the exact order of the nonadaptive system is not
required, so, as to eliminate the identification problem. The
applicability of the mentioned technique (DPT) was examined
through the solution of several problems.
This article introduces the solution of a third order system with
three adjustable parameters, controlled according to second order
reference model. The adjustable parameters have great initial error
which represent condition.
Computer simulations for the solution and analysis are provided
to demonstrate the simplicity and feasibility of the technique.
Abstract: At any point of time, a power system operating
condition should be stable, meeting various operational criteria and it
should also be secure in the event of any credible contingency. Present
day power systems are being operated closer to their stability limits
due to economic and environmental constraints. Maintaining a stable
and secure operation of a power system is therefore a very important
and challenging issue. Voltage instability has been given much
attention by power system researchers and planners in recent years,
and is being regarded as one of the major sources of power system
insecurity. Voltage instability phenomena are the ones in which the
receiving end voltage decreases well below its normal value and does
not come back even after setting restoring mechanisms such as VAR
compensators, or continues to oscillate for lack of damping against the
disturbances. Reactive power limit of power system is one of the major
causes of voltage instability. This paper investigates the effects of
coordinated series capacitors (SC) with static VAR compensators
(SVC) on steady-state voltage stability of a power system. Also, the
influence of the presence of series capacitor on static VAR
compensator controller parameters and ratings required to stabilize
load voltages at certain values are highlighted.
Abstract: We investigated the effects of modified
preprogrammed training mode Chase Trainer from Balance Trainer
(BT3, HurLab, Tampere, Finland) on athlete who experienced
unilateral Patellofemoral Pain Syndrome (PFPS). Twenty-seven
athletes with mean age= 14.23 ±1.31 years, height = 164.89 ± 7.85
cm, weight = 56.94 ± 9.28 kg were randomly assigned to two groups:
experiment (EG; n = 14) and injured (IG; n = 13). EG performed a
series of Chase Trainer program which required them to shift their
body weight at different directions, speeds and angle of leaning twice
a week for duration of 8 weeks. The static postural control and
perceived pain level measures were taken at baseline, after 6 weeks
and 8 weeks of training. There was no significant difference in any of
tested variables between EG and IG before and after 6-week the
intervention period. However, after 8-week of training, the postural
control (eyes open) and perceived pain level of EG improved
compared to IG (p
Abstract: Purpose: Planning and dosimetry of different VMAT algorithms (SmartArc, Ergo++, Autobeam) is compared with IMRT for Head and Neck Cancer patients. Modelling was performed to rule out the causes of discrepancies between planned and delivered dose. Methods: Five HNC patients previously treated with IMRT were re-planned with SmartArc (SA), Ergo++ and Autobeam. Plans were compared with each other and against IMRT and evaluated using DVHs for PTVs and OARs, delivery time, monitor units (MU) and dosimetric accuracy. Modelling of control point (CP) spacing, Leaf-end Separation and MLC/Aperture shape was performed to rule out causes of discrepancies between planned and delivered doses. Additionally estimated arc delivery times, overall plan generation times and effect of CP spacing and number of arcs on plan generation times were recorded. Results: Single arc SmartArc plans (SA4d) were generally better than IMRT and double arc plans (SA2Arcs) in terms of homogeneity and target coverage. Double arc plans seemed to have a positive role in achieving improved Conformity Index (CI) and better sparing of some Organs at Risk (OARs) compared to Step and Shoot IMRT (ss-IMRT) and SA4d. Overall Ergo++ plans achieved best CI for both PTVs. Dosimetric validation of all VMAT plans without modelling was found to be lower than ss-IMRT. Total MUs required for delivery were on average 19%, 30%, 10.6% and 6.5% lower than ss-IMRT for SA4d, SA2d (Single arc with 20 Gantry Spacing), SA2Arcs and Autobeam plans respectively. Autobeam was most efficient in terms of actual treatment delivery times whereas Ergo++ plans took longest to deliver. Conclusion: Overall SA single arc plans on average achieved best target coverage and homogeneity for both PTVs. SA2Arc plans showed improved CI and some OARs sparing. Very good dosimetric results were achieved with modelling. Ergo++ plans achieved best CI. Autobeam resulted in fastest treatment delivery times.
Abstract: In recent years asymmetric cross section aluminum
alloy stock has been finding increasing use in various industrial manufacturing areas such as general structures and automotive
components. In these areas, components are generally required to have
complex curved configuration and, as such, a bending process is required during manufacture. Undesirable deformation in bending
processes such as flattening or wrinkling can easily occur when thin-walled sections are bent. Hence, a thorough understanding of the
bending behavior of such sections is needed to prevent these undesirable deformations. In this study, the bending behavior of
asymmetric channel section was examined using finite element analysis (FEA). Typical methods of preventing undesirable
deformation, such as asymmetric laminated elastic mandrels were included in FEA model of draw bending. Additionally, axial tension
was applied to prevent wrinkling. By utilizing the FE simulations effect of restriction dies and axial tension on undesirable deformation during the process was clarified.
Abstract: Aspect Oriented Programming promises many
advantages at programming level by incorporating the cross cutting
concerns into separate units, called aspects. Join Points are
distinguishing features of Aspect Oriented Programming as they
define the points where core requirements and crosscutting concerns
are (inter)connected. Currently, there is a problem of multiple
aspects- composition at the same join point, which introduces the
issues like ordering and controlling of these superimposed aspects.
Dynamic strategies are required to handle these issues as early as
possible. State chart is an effective modeling tool to capture dynamic
behavior at high level design. This paper provides methodology to
formulate the strategies for multiple aspect composition at high level,
which helps to better implement these strategies at coding level. It
also highlights the need of designing shared join point at high level,
by providing the solutions of these issues using state chart diagrams
in UML 2.0. High level design representation of shared join points
also helps to implement the designed strategy in systematic way.
Abstract: This paper presents a new configurable decimation
filter for sigma-delta modulators. The filter employs the Pascal-s
triangle-s theorem for building the coefficients of non-recursive
decimation filters. The filter can be connected to the back-end of
various modulators with different output accuracy. In this work two
methods are shown and then compared from area occupation
viewpoint. First method uses the memory and the second one
employs Pascal-s triangle-s method, aiming to reduce required gates.
XILINX ISE v10 is used for implementation and confirmation the
filter.
Abstract: In literatures, many researches proposed various
methods to reduce PAPR (Peak to Average Power Ratio). Among
those, DSI (Dummy Sequence Insertion) is one of the most attractive
methods for WiMAX systems because it does not require side
information transmitted along with user data. However, the
conventional DSI methods find dummy sequence by performing an
iterative procedure until achieving PAPR under a desired threshold.
This causes a significant delay on finding dummy sequence and also
effects to the overall performances in WiMAX systems. In this paper,
the new method based on DSI is proposed by finding dummy
sequence without the need of iterative procedure. The fast DSI
method can reduce PAPR without either delays or required side
information. The simulation results confirm that the proposed method
is able to carry out PAPR performances as similar to the other
methods without any delays. In addition, the simulations of WiMAX
system with adaptive modulations are also investigated to realize the
use of proposed methods on various fading schemes. The results
suggest the WiMAX designers to modify a new Signal to Noise Ratio
(SNR) criteria for adaptation.
Abstract: Coagulation of water involves the use of coagulating
agents to bring the suspended matter in the raw water together for
settling and the filtration stage. Present study is aimed to examine the
effects of aluminum sulfate as coagulant in conjunction with Moringa
Oleifera Coagulant Protein as coagulant aid on turbidity, hardness,
and bacteria in turbid water. A conventional jar test apparatus was
employed for the tests. The best removal was observed at a pH of 7
to 7.5 for all turbidities. Turbidity removal efficiency was resulted
between % 80 to % 99 by Moringa Oleifera Coagulant Protein as
coagulant aid. Dosage of coagulant and coagulant aid decreased with
increasing turbidity. In addition, Moringa Oleifera Coagulant Protein
significantly has reduced the required dosage of primary coagulant.
Residual Al+3 in treated water were less than 0.2 mg/l and meets the
environmental protection agency guidelines. The results showed that
turbidity reduction of % 85.9- % 98 paralleled by a primary
Escherichia coli reduction of 1-3 log units (99.2 – 99.97%) was
obtained within the first 1 to 2 h of treatment. In conclusions,
Moringa Oleifera Coagulant Protein as coagulant aid can be used for
drinking water treatment without the risk of organic or nutrient
release. We demonstrated that optimal design method is an efficient
approach for optimization of coagulation-flocculation process and
appropriate for raw water treatment.
Abstract: Plastic waste is a big issue in Thailand, but the amount of recycled plastic in Thailand is still low due to the high investment and operating cost. Hence, the rest of plastic waste are burnt to destroy or sent to the landfills. In order to be financial viable, an effective reverse logistics infrastructure is required to support the product recovery activities. However, there is a conflict between reducing the cost and raising environmental protection level. The purpose of this study is to build a goal programming (GP) so that it can be used to help analyze the proper planning of the Thailand-s plastic recycling system that involves multiple objectives. This study considers three objectives; reducing total cost, increasing the amount of plastic recovery, and raising the desired plastic materials in recycling process. The results from two priority structures show that it is necessary to raise the total cost budget in order to achieve targets on amount of recycled plastic and desired plastic materials.