Abstract: Worldwide many electrical equipment insulation
failures have been reported caused by switching operations, while
those equipments had previously passed all the standard tests and
complied with all quality requirements. The problem is mostly
associated with high-frequency overvoltages generated during
opening or closing of a switching device. The transients generated
during switching operations in a Gas Insulated Substation (GIS) are
associated with high frequency components in the order of few tens
of MHz.
The frequency spectrum of the VFTO generated in the 220/66 kV
Wadi-Hoff GIS is analyzed using Fast Fourier Transform technique.
The main frequency with high voltage amplitude due to the operation
of disconnector (DS5) is 5 to 10 MHz, with the highest amplitude at 9
MHz. The main frequency with high voltage amplitude due to the
operation of circuit breaker (CB5) is 1 to 25 MHz, with the highest
amplitude at 2 MHz.
Mitigating techniques damped the oscillating frequencies
effectively. The using of cable terminal reduced the frequency
oscillation effectively than that of OHTL terminal. The using of a
shunt capacitance results in vanishing the high frequency
components. Ferrite rings reduces the high frequency components
effectively especially in the range 2 to 7 MHz. The using of RC and
RL filters results in vanishing the high frequency components.
Abstract: The use of a Bayesian Hierarchical Model (BHM) to interpret breath measurements obtained during a 13C Octanoic Breath Test (13COBT) is demonstrated. The statistical analysis was implemented using WinBUGS, a commercially available computer package for Bayesian inference. A hierarchical setting was adopted where poorly defined parameters associated with a delayed Gastric Emptying (GE) were able to "borrow" strength from global distributions. This is proved to be a sufficient tool to correct model's failures and data inconsistencies apparent in conventional analyses employing a Non-linear least squares technique (NLS). Direct comparison of two parameters describing gastric emptying ng ( tlag -lag phase, t1/ 2 -half emptying time) revealed a strong correlation between the two methods. Despite our large dataset ( n = 164 ), Bayesian modeling was fast and provided a successful fitting for all subjects. On the contrary, NLS failed to return acceptable estimates in cases where GE was delayed.
Abstract: Panoramic view generation has always offered
novel and distinct challenges in the field of image processing.
Panoramic view generation is nothing but construction of bigger
view mosaic image from set of partial images of the desired view.
The paper presents a solution to one of the problems of image
seascape formation where some of the partial images are color and
others are grayscale. The simplest solution could be to convert all
image parts into grayscale images and fusing them to get grayscale
image panorama. But in the multihued world, obtaining the colored
seascape will always be preferred. This could be achieved by picking
colors from the color parts and squirting them in grayscale parts of
the seascape. So firstly the grayscale image parts should be colored
with help of color image parts and then these parts should be fused to
construct the seascape image.
The problem of coloring grayscale images has no exact solution.
In the proposed technique of panoramic view generation, the job of
transferring color traits from reference color image to grayscale
image is done by palette based method. In this technique, the color
palette is prepared using pixel windows of some degrees taken from
color image parts. Then the grayscale image part is divided into pixel
windows with same degrees. For every window of grayscale image
part the palette is searched and equivalent color values are found,
which could be used to color grayscale window. For palette
preparation we have used RGB color space and Kekre-s LUV color
space. Kekre-s LUV color space gives better quality of coloring. The
searching time through color palette is improved over the exhaustive
search using Kekre-s fast search technique.
After coloring the grayscale image pieces the next job is fusion of
all these pieces to obtain panoramic view. For similarity estimation
between partial images correlation coefficient is used.
Abstract: Timing driven physical design, synthesis, and
optimization tools need efficient closed-form delay models for
estimating the delay associated with each net in an integrated circuit
(IC) design. The total number of nets in a modern IC design has
increased dramatically and exceeded millions. Therefore efficient
modeling of interconnection is needed for high speed IC-s. This
paper presents closed–form expressions for RC and RLC
interconnection trees in current mode signaling, which can be
implemented in VLSI design tool. These analytical model
expressions can be used for accurate calculation of delay after the
design clock tree has been laid out and the design is fully routed.
Evaluation of these analytical models is several orders of magnitude
faster than simulation using SPICE.
Abstract: This paper describes an efficient hardware implementation of a new technique for interfacing the data exchange between the microprocessor-based systems and the external devices. This technique, based on the use of software/hardware system and a reduced physical address, enlarges the interfacing capacity of the microprocessor-based systems, uses the Direct Memory Access (DMA) to increases the frequency of the new bus, and improves the speed of data exchange. While using this architecture in microprocessor-based system or in computer, the input of the hardware part of our system will be connected to the bus system, and the output, which is a new bus, will be connected to an external device. The new bus is composed of a data bus, a control bus and an address bus. A Xilinx Integrated Software Environment (ISE) 7.1i has been used for the programmable logic implementation.
Abstract: Fast forecasting of stock market prices is very important for
strategic planning. In this paper, a new approach for fast forecasting of
stock market prices is presented. Such algorithm uses new high speed
time delay neural networks (HSTDNNs). The operation of these
networks relies on performing cross correlation in the frequency
domain between the input data and the input weights of neural
networks. It is proved mathematically and practically that the number
of computation steps required for the presented HSTDNNs is less
than that needed by traditional time delay neural networks
(TTDNNs). Simulation results using MATLAB confirm the
theoretical computations.
Abstract: Industrial radiography is a famous technique for the identification and evaluation of discontinuities, or defects, such as cracks, porosity and foreign inclusions found in welded joints. Although this technique has been well developed, improving both the inspection process and operating time, it does suffer from several drawbacks. The poor quality of radiographic images is due to the physical nature of radiography as well as small size of the defects and their poor orientation relatively to the size and thickness of the evaluated parts. Digital image processing techniques allow the interpretation of the image to be automated, avoiding the presence of human operators making the inspection system more reliable, reproducible and faster. This paper describes our attempt to develop and implement digital image processing algorithms for the purpose of automatic defect detection in radiographic images. Because of the complex nature of the considered images, and in order that the detected defect region represents the most accurately possible the real defect, the choice of global and local preprocessing and segmentation methods must be appropriated.
Abstract: The main goal of the present work is to decrease the
computational burden for optimum design of steel frames with
frequency constraints using a new type of neural networks called
Wavelet Neural Network. It is contested to train a suitable neural
network for frequency approximation work as the analysis program.
The combination of wavelet theory and Neural Networks (NN)
has lead to the development of wavelet neural networks.
Wavelet neural networks are feed-forward networks using
wavelet as activation function. Wavelets are mathematical
functions within suitable inner parameters, which help them to
approximate arbitrary functions. WNN was used to predict the
frequency of the structures. In WNN a RAtional function with
Second order Poles (RASP) wavelet was used as a transfer
function. It is shown that the convergence speed was faster
than other neural networks. Also comparisons of WNN with
the embedded Artificial Neural Network (ANN) and with
approximate techniques and also with analytical solutions are
available in the literature.
Abstract: The purpose of this study is to present a non invasive
method for the marginal adaptation evaluation in class V composite
restorations. Standardized class V cavities, prepared in human
extracted teeth, were filled with Premise (Kerr) composite. The
specimens were thermo cycled. The interfaces were examined by
Optical Coherence Tomography method (OCT) combined with the
confocal microscopy and fluorescence. The optical configuration
uses two single mode directional couplers with a superluminiscent
diode as the source at 1300 nm. The scanning procedure is similar to
that used in any confocal microscope, where the fast scanning is enface
(line rate) and the depth scanning is much slower (at the frame
rate). Gaps at the interfaces as well as inside the composite resin
materials were identified. OCT has numerous advantages which
justify its use in vivo as well as in vitro in comparison with
conventional techniques.
Abstract: In this study, effects of premixed and equivalence
ratios on CO and HC emissions of a dual fuel HCCI engine are
investigated. Tests were conducted on a single-cylinder engine with
compression ratio of 17.5. Premixed gasoline is provided by a
carburetor connected to intake manifold and equipped with a screw
to adjust premixed air-fuel ratio, and diesel fuel is injected directly
into the cylinder through an injector at pressure of 250 bars. A heater
placed at inlet manifold is used to control the intake charge
temperature. Optimal intake charge temperature results in better
HCCI combustion due to formation of a homogeneous mixture,
therefore, all tests were carried out over the optimum intake
temperature of 110-115 ºC. Timing of diesel fuel injection has a great
effect on stratification of in-cylinder charge and plays an important
role in HCCI combustion phasing. Experiments indicated 35 BTDC
as the optimum injection timing. Varying the coolant temperature in
a range of 40 to 70 ºC, better HCCI combustion was achieved at 50
ºC. Therefore, coolant temperature was maintained 50 ºC during all
tests. Simultaneous investigation of effective parameters on HCCI
combustion was conducted to determine optimum parameters
resulting in fast transition to HCCI combustion. One of the
advantages of the method studied in this study is feasibility of easy
and fast transition of typical diesel engine to a dual fuel HCCI
engine. Results show that increasing premixed ratio, while keeping
EGR rate constant, increases unburned hydrocarbon (UHC)
emissions due to quenching phenomena and trapping of premixed
fuel in crevices, but CO emission decreases due to increase in CO to
CO2 reactions.
Abstract: Recently, an enhanced hexagon-based search (EHS)
algorithm was proposed to speedup the original hexagon-based search
(HS) by exploiting the group-distortion information of some evaluated
points. In this paper, a second version of the EHS is proposed with a
new point-oriented inner search technique which can further speedup
the HS in both large and small motion environments. Experimental
results show that the enhanced hexagon-based search version-2
(EHS2) is faster than the HS up to 34% with negligible PSNR
degradation.
Abstract: The index of sustainable functionality (ISF) is an adaptive, multi-criteria technique that is used to measure sustainability; it is a concept that can be transposed to many regions throughout the world. An ISF application of the Southern Regional Organisation of Councils (SouthROC) in South East Queensland (SEQ) – the fastest growing region in Australia – indicated over a 25 year period an increase of over 10% level of functionality from 58.0% to 68.3%. The ISF of SouthROC utilised methodologies that derived from an expert panel based approach. The overall results attained an intermediate level of functionality which amounted to related concerns of economic progress and lack of social awareness. Within the region, a solid basis for future testing by way of measured changes and developed trends can be established. In this regard as management tool, the ISF record offers support for regional sustainability practice and decision making alike. This research adaptively analyses sustainability – a concept that is lacking throughout much of the academic literature and any reciprocal experimentation. This lack of knowledge base has been the emphasis of where future sustainability research can grow from and prove useful in rapidly growing regions. It is the intentions of this research to help further develop the notions of index-based quantitative sustainability.
Abstract: Recently, fast neural networks for object/face
detection were presented in [1-3]. The speed up factor of these
networks relies on performing cross correlation in the frequency
domain between the input image and the weights of the hidden
layer. But, these equations given in [1-3] for conventional and fast
neural networks are not valid for many reasons presented here. In
this paper, correct equations for cross correlation in the spatial and
frequency domains are presented. Furthermore, correct formulas for
the number of computation steps required by conventional and fast
neural networks given in [1-3] are introduced. A new formula for
the speed up ratio is established. Also, corrections for the equations
of fast multi scale object/face detection are given. Moreover,
commutative cross correlation is achieved. Simulation results show
that sub-image detection based on cross correlation in the frequency
domain is faster than classical neural networks.
Abstract: A neurofuzzy approach for a given set of input-output training data is proposed in two phases. Firstly, the data set is partitioned automatically into a set of clusters. Then a fuzzy if-then rule is extracted from each cluster to form a fuzzy rule base. Secondly, a fuzzy neural network is constructed accordingly and parameters are tuned to increase the precision of the fuzzy rule base. This network is able to learn and optimize the rule base of a Sugeno like Fuzzy inference system using Hybrid learning algorithm, which combines gradient descent, and least mean square algorithm. This proposed neurofuzzy system has the advantage of determining the number of rules automatically and also reduce the number of rules, decrease computational time, learns faster and consumes less memory. The authors also investigate that how neurofuzzy techniques can be applied in the area of control theory to design a fuzzy controller for linear and nonlinear dynamic systems modelling from a set of input/output data. The simulation analysis on a wide range of processes, to identify nonlinear components on-linely in a control system and a benchmark problem involving the prediction of a chaotic time series is carried out. Furthermore, the well-known examples of linear and nonlinear systems are also simulated under the Matlab/Simulink environment. The above combination is also illustrated in modeling the relationship between automobile trips and demographic factors.
Abstract: In this paper, we present a system for content-based
retrieval of large database of classified satellite images, based on
user's relevance feedback (RF).Through our proposed system, we
divide each satellite image scene into small subimages, which stored
in the database. The modified radial basis functions neural network
has important role in clustering the subimages of database according
to the Euclidean distance between the query feature vector and the
other subimages feature vectors. The advantage of using RF
technique in such queries is demonstrated by analyzing the database
retrieval results.
Abstract: This paper uses the radial basis function neural
network (RBFNN) for system identification of nonlinear systems.
Five nonlinear systems are used to examine the activity of RBFNN in
system modeling of nonlinear systems; the five nonlinear systems are
dual tank system, single tank system, DC motor system, and two
academic models. The feed forward method is considered in this
work for modelling the non-linear dynamic models, where the KMeans
clustering algorithm used in this paper to select the centers of
radial basis function network, because it is reliable, offers fast
convergence and can handle large data sets. The least mean square
method is used to adjust the weights to the output layer, and
Euclidean distance method used to measure the width of the Gaussian
function.
Abstract: In this note, we discuss the convergence behavior of a modified inexact Uzawa algorithm for solving generalized saddle point problems, which is an extension of the result obtained in a recent paper [Z.H. Cao, Fast Uzawa algorithm for generalized saddle point problems, Appl. Numer. Math., 46 (2003) 157-171].
Abstract: Here, a new idea to speed up the operation of
complex valued time delay neural networks is presented. The whole
data are collected together in a long vector and then tested as a one
input pattern. The proposed fast complex valued time delay neural
networks uses cross correlation in the frequency domain between the
tested data and the input weights of neural networks. It is proved
mathematically that the number of computation steps required for
the presented fast complex valued time delay neural networks is less
than that needed by classical time delay neural networks. Simulation
results using MATLAB confirm the theoretical computations.
Abstract: In the globalization context and competitiveness, the role of a university is further enhanced. University is no longer confined to traditional roles. Universities need to interact with others in order to be relevant and progressive. Symbiosis relationships between the university and industry are very significant because the relationship between those two can foster economic development of a nation. In a world of fast changing technology and competition, it is necessary for the university to collaborate with industry to combine efforts fostering the diffusion of knowledge, increasing research and development, patenting innovation and commercializing products. It has become increasingly accepted that the necessity of close university-industry interactions as a mean of national economic prosperity. Therefore, this paper is aim to examine the level of linkages in university-industry interactions to which promotes the regional economic growth and development. This paper will explore the formation of linkages between the Higher Education Institution (University Technology MARA) and industries located in the Klang Valley region of Malaysia. It will present the university-industry linkages with emphasis on the type of linkages existed, the benefits of having such linkages to promote regional economic development and finally the constraints that might impede the linkages and potentials to enhance the linkages towards economic growth and development.
Abstract: One of the most important problems to solve is eye
location for a driver fatigue monitoring system. This paper presents an
efficient method to achieve fast and accurate eye location in grey level
images obtained in the real-word driving conditions. The structure of
eye region is used as a robust cue to find possible eye pairs. Candidates
of eye pair at different scales are selected by finding regions which
roughly match with the binary eye pair template. To obtain real one,
all the eye pair candidates are then verified by using support vector
machines. Finally, eyes are precisely located by using binary vertical
projection and eye classifier in eye pair images. The proposed method
is robust to deal with illumination changes, moderate rotations, glasses
wearing and different eye states. Experimental results demonstrate its
effectiveness.