Abstract: Salinity is a measure of the amount of salts in the
water. Total Dissolved Solids (TDS) as salinity parameter are often
determined using laborious and time consuming laboratory tests, but
it may be more appropriate and economical to develop a method
which uses a more simple soil salinity index. Because dissolved ions
increase salinity as well as conductivity, the two measures are
related. The aim of this research was determine of constant
coefficients for predicting of Total Dissolved Solids (TDS) based on
Electrical Conductivity (EC) with Statistics of Correlation
coefficient, Root mean square error, Maximum error, Mean Bias
error, Mean absolute error, Relative error and Coefficient of residual
mass. For this purpose, two experimental areas (S1, S2) of Khuzestan
province-IRAN were selected and four treatments with three
replications by series of double rings were applied. The treatments
were included 25cm, 50cm, 75cm and 100cm water application. The
results showed the values 16.3 & 12.4 were the best constant
coefficients for predicting of Total Dissolved Solids (TDS) based on
EC in Pilot S1 and S2 with correlation coefficient 0.977 & 0.997 and
191.1 & 106.1 Root mean square errors (RMSE) respectively.
Abstract: Isobaric vapor-liquid equilibrium measurements are
reported for binary mixture of 2-Methyltetrahydrofuran and Cumene
at 97.3 kPa. The data were obtained using a vapor recirculating type
(modified Othmer's) equilibrium still. The mixture shows slight
negative deviation from ideality. The system does not form an
azeotrope. The experimental data obtained in this study are
thermodynamically consistent according to the Herington test. The
activity coefficients have been satisfactorily correlated by means of
the Margules, and NRTL equations. Excess Gibbs free energy has
been calculated from the experimental data. The values of activity
coefficients have also been obtained by the UNIFAC group
contribution method.
Abstract: We are concerned with a class of quadratic matrix
equations arising from the overdamped mass-spring system. By
exploring the structure of coefficient matrices, we propose a fast
cyclic reduction algorithm to calculate the extreme solutions of the
equation. Numerical experiments show that the proposed algorithm
outperforms the original cyclic reduction and the structure-preserving
doubling algorithm.
Abstract: The use of additions in cement in manufacturing,
mortar and concrete offers economic and ecological advantages. Cements with additions such as limestone, slag and natural
pouzzolana are produced in cement factories in Algeria. Several studies analyzed the effect of these additions on the physical and
mechanical properties as well as the durability of concrete. However,
few studies were conducted on the effect of local metakaolin on
mechanical properties and durability of concrete. The main purpose
of this paper is to analyze the performance of mortar and concrete with local metakaolin. The preparation of the metakaolin was carried
out by calcination of kaolin at a temperature of 850 °C for a period of 3 hours. The experimental results have shown that the rates of
substitutions of 10 and 15% metakaolin increases the compressive
strength and flexural strength at both early age and long term. The durability and the permeability were also improved by reducing the
coefficient of sorptivity.
Abstract: Reactiondiffusion systems are mathematical models that describe how the concentration of one or more substances distributed in space changes under the influence of local chemical reactions in which the substances are converted into each other, and diffusion which causes the substances to spread out in space. The classical representation of a reaction-diffusion system is given by semi-linear parabolic partial differential equations, whose general form is ÔêétX(x, t) = DΔX(x, t), where X(x, t) is the state vector, D is the matrix of the diffusion coefficients and Δ is the Laplace operator. If the solute move in an homogeneous system in thermal equilibrium, the diffusion coefficients are constants that do not depend on the local concentration of solvent and of solutes and on local temperature of the medium. In this paper a new stochastic reaction-diffusion model in which the diffusion coefficients are function of the local concentration, viscosity and frictional forces of solvent and solute is presented. Such a model provides a more realistic description of the molecular kinetics in non-homogenoeus and highly structured media as the intra- and inter-cellular spaces. The movement of a molecule A from a region i to a region j of the space is described as a first order reaction Ai k- → Aj , where the rate constant k depends on the diffusion coefficient. Representing the diffusional motion as a chemical reaction allows to assimilate a reaction-diffusion system to a pure reaction system and to simulate it with Gillespie-inspired stochastic simulation algorithms. The stochastic time evolution of the system is given by the occurrence of diffusion events and chemical reaction events. At each time step an event (reaction or diffusion) is selected from a probability distribution of waiting times determined by the specific speed of reaction and diffusion events. Redi is the software tool, developed to implement the model of reaction-diffusion kinetics and dynamics. It is a free software, that can be downloaded from http://www.cosbi.eu. To demonstrate the validity of the new reaction-diffusion model, the simulation results of the chaperone-assisted protein folding in cytoplasm obtained with Redi are reported. This case study is redrawing the attention of the scientific community due to current interests on protein aggregation as a potential cause for neurodegenerative diseases.
Abstract: In this paper, various algorithms for designing quadrature mirror filter are reviewed and a new algorithm is presented for the design of near perfect reconstruction quadrature mirror filter bank. In the proposed algorithm, objective function is formulated using the perfect reconstruction condition or magnitude response condition of prototype filter at frequency (ω = 0.5π) in ideal condition. The cutoff frequency is iteratively changed to adjust the filters coefficients using optimization algorithm. The performances of the proposed algorithm are evaluated in term of computation time, reconstruction error and number of iterations. The design examples illustrate that the proposed algorithm is superior in term of peak reconstruction error, computation time, and number of iterations. The proposed algorithm is simple, easy to implement, and linear in nature.
Abstract: This paper presents features that characterize power
quality disturbances from recorded voltage waveforms using wavelet
transform. The discrete wavelet transform has been used to detect
and analyze power quality disturbances. The disturbances of interest
include sag, swell, outage and transient. A power system network has
been simulated by Electromagnetic Transients Program. Voltage
waveforms at strategic points have been obtained for analysis, which
includes different power quality disturbances. Then wavelet has been
chosen to perform feature extraction. The outputs of the feature
extraction are the wavelet coefficients representing the power quality
disturbance signal. Wavelet coefficients at different levels reveal the
time localizing information about the variation of the signal.
Abstract: This paper addresses the stabilization issues for a class of uncertain switched neutral systems with nonlinear perturbations. Based on new classes of piecewise Lyapunov functionals, the stability assumption on all the main operators or the convex combination of coefficient matrices is avoid, and a new switching rule is introduced to stabilize the neutral systems. The switching rule is designed from the solution of the so-called Lyapunov-Metzler linear matrix inequalities. Finally, three simulation examples are given to demonstrate the significant improvements over the existing results.
Abstract: In this manuscript, a wavelet-based blind
watermarking scheme has been proposed as a means to provide
security to authenticity of a fingerprint. The information used for
identification or verification of a fingerprint mainly lies in its
minutiae. By robust watermarking of the minutiae in the fingerprint
image itself, the useful information can be extracted accurately even
if the fingerprint is severely degraded. The minutiae are converted in
a binary watermark and embedding these watermarks in the detail
regions increases the robustness of watermarking, at little to no
additional impact on image quality. It has been experimentally shown
that when the minutiae is embedded into wavelet detail coefficients
of a fingerprint image in spread spectrum fashion using a
pseudorandom sequence, the robustness is observed to have a
proportional response while perceptual invisibility has an inversely
proportional response to amplification factor “K". The DWT-based
technique has been found to be very robust against noises,
geometrical distortions filtering and JPEG compression attacks and is
also found to give remarkably better performance than DCT-based
technique in terms of correlation coefficient and number of erroneous
minutiae.
Abstract: In the present work an investigation of the effects of
the air frontal velocity, relative humidity and dry air temperature on
the heat transfer characteristics of plain finned tube evaporator has
been conducted. Using an appropriate correlation for the air side heat
transfer coefficient the temperature distribution along the fin surface
was calculated using a dimensionless temperature distribution. For a
constant relative humidity and bulb temperature, it is found that the
temperature distribution decreases with increasing air frontal
velocity. Apparently, it is attributed to the condensate water film
flowing over the fin surface. When dry air temperature and face
velocity are being kept constant, the temperature distribution
decreases with the increase of inlet relative humidity. An increase in
the inlet relative humidity is accompanied by a higher amount of
moisture on the fin surface. This results in a higher amount of latent
heat transfer which involves higher fin surface temperature. For the
influence of dry air temperature, the results here show an increase in
the dimensionless temperature parameter with a decrease in bulb
temperature. Increasing bulb temperature leads to higher amount of
sensible and latent heat transfer when other conditions remain
constant.
Abstract: The present paper reports the removal of Cd(II) and
Zn(II) ions using synthetic Zeolit NaA. The adsorption capacity of
the sorbent (Zeolite NaA) strongly depends on simultaneous or not
simultaneous (concurrent) presence of Cd(II) and Zn(II) in the
sorbate. When Cd(II) and Zn(II) are present simultaneously
(concurrently) in the sorbate, Zn(II) ions were sorbed at higher rate.
Equilibrium data fitted Langmuir, Freundlich and Tempkin isotherms
well. The applicability of the isotherm equation to describe the
adsorption process was judged by the correlation coefficients R2. The
Langmuir model yielded the best fit with R2 values equal to or higher
than 0.970, as compared to the Freundlich and Tempkin models. The
fact that 1/n values range from 0.322 to 0.755 indicates that the
adsorption of Cd(II) and Zn(II) ions from aqueous solutions also
favored by the Freundlich model.
Abstract: Physical and mechanical properties of Russian olive
fruits were measured at moisture content of 14.43% w.b. The results
revealed that the mean length, width and thickness of Russian olive
fruits were 20.72, 15.73 and 14.69mm, respectively. Mean mass and
volume of Russian olive fruits were measured as 1.45 g and 2.55 cm3,
respectively. The sphericity, aspect ratio and surface area were
calculated as 0.81, 0.72 and 8.96 cm2, respectively, while arithmetic
mean diameter, geometric mean diameter and equivalent diameter of
Russian olive fruits were 17.05, 16.83 and 16.84 mm, respectively.
Whole fruit density, bulk density and porosity of jujube fruits were
measured and found to be 1.01 g/cm3, 0.29 g/cm3 and 69.5%,
respectively. The values of static coefficient of friction on three
surfaces of glass, galvanized iron and plywood were 0.35, 0.36 and
0.43, respectively. The skin color (L*, a*, b*) varied from 9.92 to
16.08; 2.04 to 3.91 and 1.12 to 3.83, respectively. The values of
rupture force, deformation, energy absorbed and hardness were found
to be between 12.14-16.85 N, 2.16-4.25 mm, 3.42-6.99 N mm and
17.1-23.85 N/mm.
Abstract: Experimental liquid-liquid equilibra of butan-2-ol -
ethanol -water; pentan-1-ol - ethanol - water and toluene - acetone -
water ternary systems were investigated at (25oC). The reliability of
the experimental tie-line data was ascertained by using Othmer-Tobias
and Hand plots. The distribution coefficients (D) and separation
factors (S) of the immiscibility region were evaluated for the three
systems.
Abstract: An artificial neural network (ANN) model is
presented for the prediction of kinematic viscosity of binary mixtures
of poly (ethylene glycol) (PEG) in water as a function of temperature,
number-average molecular weight and mass fraction. Kinematic
viscosities data of aqueous solutions for PEG (0.55419×10-6 –
9.875×10-6 m2/s) were obtained from the literature for a wide range
of temperatures (277.15 - 338.15 K), number-average molecular
weight (200 -10000), and mass fraction (0.0 – 1.0). A three layer
feed-forward artificial neural network was employed. This model
predicts the kinematic viscosity with a mean square error (MSE) of
0.281 and the coefficient of determination (R2) of 0.983. The results
show that the kinematic viscosity of binary mixture of PEG in water
could be successfully predicted using an artificial neural network
model.
Abstract: Panoramic view generation has always offered
novel and distinct challenges in the field of image processing.
Panoramic view generation is nothing but construction of bigger
view mosaic image from set of partial images of the desired view.
The paper presents a solution to one of the problems of image
seascape formation where some of the partial images are color and
others are grayscale. The simplest solution could be to convert all
image parts into grayscale images and fusing them to get grayscale
image panorama. But in the multihued world, obtaining the colored
seascape will always be preferred. This could be achieved by picking
colors from the color parts and squirting them in grayscale parts of
the seascape. So firstly the grayscale image parts should be colored
with help of color image parts and then these parts should be fused to
construct the seascape image.
The problem of coloring grayscale images has no exact solution.
In the proposed technique of panoramic view generation, the job of
transferring color traits from reference color image to grayscale
image is done by palette based method. In this technique, the color
palette is prepared using pixel windows of some degrees taken from
color image parts. Then the grayscale image part is divided into pixel
windows with same degrees. For every window of grayscale image
part the palette is searched and equivalent color values are found,
which could be used to color grayscale window. For palette
preparation we have used RGB color space and Kekre-s LUV color
space. Kekre-s LUV color space gives better quality of coloring. The
searching time through color palette is improved over the exhaustive
search using Kekre-s fast search technique.
After coloring the grayscale image pieces the next job is fusion of
all these pieces to obtain panoramic view. For similarity estimation
between partial images correlation coefficient is used.
Abstract: Prediction of benzene transport in soil and volatilization from soil to the atmosphere is important for the preservation of human health and management of contaminated soils. The adequacy of a simple numerical model, assuming two-phase diffusion and equilibrium of liquid/solid adsorption, was investigated by experimental data of benzene concentration in a flux chamber (with headspace) where Andosol and sand were filled. Adsorption experiment for liquid phase was performed to determine an adsorption coefficient. Furthermore, adequacy of vapor phase adsorption was also studied through two runs of experiment using sand with different water content. The results show that the model adequately predicted benzene transport and volatilization from Andosol and sand with water content of 14.0%. In addition, the experiment additionally revealed that vapor phase adsorption should be considered in diffusion model for sand with very low water content.
Abstract: This paper studies stability of homogeneous beams
with piezoelectric layers subjected to axial load that is simply
supported at both ends lies on a continuous elastic foundation. The
displacement field of beam is assumed based on first order shear
deformation beam theory. Applying the Hamilton's principle, the
governing equation is established. The influences of applied voltage,
dimensionless geometrical parameter and foundation coefficient on
the stability of beam are presented. To investigate the accuracy of the
present analysis, a compression study is carried out with a known
data.
Abstract: Bicycle configuration is not as large as those of motorcycles or automobiles, while it indeed composes a complicated dynamic system. People-s requirements on comfortability, controllability and safety grow higher as the research and development technologies improve. The shock absorber affects the vehicle suspension performances enormously. The absorber takes the vibration energy and releases it at a suitable time, keeping the wheel under a proper contact condition with road surface, maintaining the vehicle chassis stability. Suspension design for mountain bicycles is more difficult than that of city bikes since it encounters dynamic variations on road and loading conditions. Riders need a stiff damper as they exert to tread on the pedals when climbing, while a soft damper when they descend downhill. Various switchable shock absorbers are proposed in markets, however riders have to manually switch them among soft, hard and lock positions. This study proposes a novel design of the bicycle shock absorber, which provides automatic smooth tuning of the damping coefficient, from a predetermined lower bound to theoretically unlimited. An automatic quick releasing valve is involved in this design so that it can release the peak pressure when the suspension fork runs into a square-wave type obstacle and prevent the chassis from damage, avoiding the rider skeleton from injury. This design achieves the automatic tuning process by innovative plunger valve and fluidic passage arrangements without any electronic devices. Theoretical modelling of the damper and spring are established in this study. Design parameters of the valves and fluidic passages are determined. Relations between design parameters and shock absorber performances are discussed in this paper. The analytical results give directions to the shock absorber manufacture.
Abstract: Mel Frequency Cepstral Coefficient (MFCC) features
are widely used as acoustic features for speech recognition as well
as speaker recognition. In MFCC feature representation, the Mel frequency
scale is used to get a high resolution in low frequency region,
and a low resolution in high frequency region. This kind of processing
is good for obtaining stable phonetic information, but not suitable
for speaker features that are located in high frequency regions. The
speaker individual information, which is non-uniformly distributed
in the high frequencies, is equally important for speaker recognition.
Based on this fact we proposed an admissible wavelet packet based
filter structure for speaker identification. Multiresolution capabilities
of wavelet packet transform are used to derive the new features.
The proposed scheme differs from previous wavelet based works,
mainly in designing the filter structure. Unlike others, the proposed
filter structure does not follow Mel scale. The closed-set speaker
identification experiments performed on the TIMIT database shows
improved identification performance compared to other commonly
used Mel scale based filter structures using wavelets.
Abstract: This paper deals with rheological behavior of tomato
paste from the view point of time independent properties inclusive of
processing variables such as sample temperature which influence on
rheological properties as well as breaking temperature and
concentration which beside the rheological properties, influence on
the quality of final product. With this aim 10 tomato paste samples at
various concentrations (17-25%) and breaking temperatures (65-
85 C o ) have been produced. The experimental results showed tomato
paste behaves as a non-Newtonian semi-fluid which follows power
law model that consistency coefficient (K) is supposed function of
breaking temperature, concentration and sample temperature with
consideration to superimpose function.