Abstract: China is currently the world's largest producer and distributor of electric bicycle (e-bike). The increasing number of e-bikes on the road is accompanied by rising injuries and even deaths of e-bike drivers. Therefore, there is a growing need to improve the safety structure of e-bikes. This 3D frictionless contact analysis is a preliminary, but necessary work for further structural design improvement of an e-bike. The contact analysis between e-bike and the ground was carried out as follows: firstly, the Penalty method was illustrated and derived from the simplest spring-mass system. This is one of the most common methods to satisfy the frictionless contact case; secondly, ANSYS static analysis was carried out to verify finite element (FE) models with contact pair (without friction) between e-bike and the ground; finally, ANSYS transient analysis was used to obtain the data of the penetration p(u) of e-bike with respect to the ground. Results obtained from the simulation are as estimated by comparing with that from theoretical method. In the future, protective shell will be designed following the stability criteria and added to the frame of e-bike. Simulation of side falling of the improvedsafety structure of e-bike will be confirmed with experimental data.
Abstract: This work reports the potential of using Palm Kernel
(PK) ash and shell as a partial substitute for Portland Cement (PC)
and coarse aggregate in the development of mortar and concrete. PK
ash and shell are agro-waste materials from palm oil mills, the
disposal of PK ash and shell is an environmental problem of concern.
The PK ash has pozzolanic properties that enables it as a partial
replacement for cement and also plays an important role in the
strength and durability of concrete, its use in concrete will alleviate
the increasing challenges of scarcity and high cost of cement. In order
to investigate the PC replacement potential of PK ash, three types of
PK ash were produced at varying temperature (350-750C) and they
were used to replace up to 50% PC. The PK shell was used to replace
up to 100% coarse aggregate in order to study its aggregate
replacement potential. The testing programme included material
characterisation, the determination of compressive strength, tensile
splitting strength and chemical durability in aggressive sulfatebearing
exposure conditions. The 90 day compressive results showed
a significant strength gain (up to 26.2 N/mm2). The Portland cement
and conventional coarse aggregate has significantly higher influence
in the strength gain compared to the equivalent PK ash and PK shell.
The chemical durability results demonstrated that after a prolonged
period of exposure, significant strength losses in all the concretes
were observed. This phenomenon is explained, due to lower change
in concrete morphology and inhibition of reaction species and the
final disruption of the aggregate cement paste matrix.
Abstract: This paper presents the details of a numerical study of
buckling and post buckling behaviour of laminated carbon fiber
reinforced plastic (CFRP) thin-walled cylindrical shell under axial
compression using asymmetric meshing technique (AMT) by
ABAQUS. AMT is considered to be a new perturbation method to
introduce disturbance without changing geometry, boundary
conditions or loading conditions. Asymmetric meshing affects both
predicted buckling load and buckling mode shapes. Cylindrical shell
having lay-up orientation [0^o/+45^o/-45^o/0^o] with radius to thickness
ratio (R/t) equal to 265 and length to radius ratio (L/R) equal to 1.5 is
analysed numerically. A series of numerical simulations
(experiments) are carried out with symmetric and asymmetric
meshing to study the effect of asymmetric meshing on predicted
buckling behaviour. Asymmetric meshing technique is employed in
both axial direction and circumferential direction separately using
two different methods, first by changing the shell element size and
varying the total number elements, and second by varying the shell
element size and keeping total number of elements constant. The
results of linear analysis (Eigenvalue analysis) and non-linear
analysis (Riks analysis) using symmetric meshing agree well with
analytical results. The results of numerical analysis are presented in
form of non-dimensional load factor, which is the ratio of buckling
load using asymmetric meshing technique to buckling load using
symmetric meshing technique. Using AMT, load factor has about 2%
variation for linear eigenvalue analysis and about 2% variation for
non-linear Riks analysis. The behaviour of load end-shortening curve
for pre-buckling is same for both symmetric and asymmetric meshing
but for asymmetric meshing curve behaviour in post-buckling
becomes extraordinarily complex. The major conclusions are:
different methods of AMT have small influence on predicted
buckling load and significant influence on load displacement curve
behaviour in post buckling; AMT in axial direction and AMT in
circumferential direction have different influence on buckling load
and load displacement curve in post-buckling.
Abstract: The transition period of Kosovo society brought
fundamental changes in all the spheres of organizing life. This was
the period when also in the cultural tradition the biggest movement
and an emerging from ‘isolation’ or from the ‘shell’ occurred.
Transformation of the traditional and embracing of the modern began
here. The same was experienced and is currently being experienced
also by Gjakova and its surrounding which is historically renowned
for its great tradition and culture.
The population of this region is actually facing a transition from
the traditional system into the modern one and quite often with huge
leaps.
These ‘movements’ or ‘evolutions’ of the society of this region,
besides the numerous positive things it ‘harvested’, also brought
things that do not at all correspond with their tradition as well as new
criminal occurrences which in the past were not present in this area.
Furthermore, some of the ‘new’ behaviors that are embraced from
other ‘cultures’ and ‘civilizations’, and which are often exceeded, are
quite perturbing. The security situation is also worrying, particularly
following the appearance of some new criminal occurrences.
Therefore, with this research paper we will strive to analyze the
new cultural “intersections” as well as the nature of the origin of
some new very worrying criminal occurrences. We will present there
also some factors inciting into these occurrences, which were
confessed by the persons involved in these criminal occurrences and
who come from this very region.
Abstract: Due to the determination of the pollution status of
fresh resources in the Egyptian territorial waters is very important for
public health; this study was carried out to reveal the levels of heavy
metals in the shellfish and their environment and its relation to the
highly developed industrial activities in those areas. A total of 100
shellfish samples from the Rosetta, Edku, El-Maadiya, Abo-Kir and
El-Max coasts [10 crustaceans (shrimp) and 10 mollusks (oysters)]
were randomly collected from each coast. Additionally, 10 samples
from both the water and the sediment were collected from each coast.
Each collected sample was analyzed for cadmium, chromium,
copper, lead and zinc residues using a Perkin Elmer atomic
absorption spectrophotometer (AAS). The results showed that the
levels of heavy metals were higher in the water and sediment from
Abo-Kir. The heavy metal levels decreased successively for the
Rosetta, Edku, El-Maadiya, and El-Max coasts, and the
concentrations of heavy metals, except copper and zinc, in shellfish
exhibited the same pattern. For the concentration of heavy metals in
shellfish tissue, the highest was zinc and the concentrations decreased
successively for copper, lead, chromium and cadmium for all coasts,
except the Abo-Kir coast, where the chromium level was highest and
the other metals decreased successively for zinc, copper, lead and
cadmium. In Rosetta, chromium was higher only in the mollusks,
while the level of this metal was lower in the crustaceans; this trend
was observed at the Edku, El-Maadiya and El-Max coasts as well.
Herein, we discuss the importance of such contamination for public
health and the sources of shellfish contamination with heavy metals.
We suggest measures to minimize and prevent these pollutants in the
aquatic environment and, furthermore, how to protect humans from
excessive intake.
Abstract: The discarded clam shell waste, fossil and edible oil
as biolubricant feedstocks create environmental impacts and food
chain dilemma, thus this work aims to circumvent these issues by
using activated saltwater clam shell waste (SCSW) as solid catalyst
for conversion of Jatropha curcas oil as non-edible sources to ester
biolubricant. The characterization of solid catalyst was done by
Differential Thermal Analysis-Thermo Gravimetric Analysis (DTATGA),
X-Ray Fluorescence (XRF), X-Ray Diffraction (XRD),
Brunauer-Emmett-Teller (BET), Field Emission Scanning Electron
Microscopy (FESEM) and Fourier Transformed Infrared
Spectroscopy (FTIR) analysis. The calcined catalyst was used in the
transesterification of Jatropha oil to methyl ester as the first step, and
the second stage was involved the reaction of Jatropha methyl ester
(JME) with trimethylolpropane (TMP) based on the various process
parameters. The formated biolubricant was analyzed using the
capillary column (DB-5HT) equipped Gas Chromatography (GC).
The conversion results of Jatropha oil to ester biolubricant can be
found nearly 96.66%, and the maximum distribution composition
mainly contains 72.3% of triester (TE).
Abstract: The study deals with the challenges in developing a
test rig to test the performance of water lubricated journal bearing.
The test rig is designed to simulate the working conditions of the
bearing in order to understand their performance before they are put
in operation. The bearing that is studied is the commercially available
water lubricated bearing which has a rubber liner bonded with a rigid
metal shell. The lubricant enters the bearing axially through a
pressurized inlet tank and exits to an outlet tank which is at
sufficiently low pressure. The load on the bearing is applied through
the dead weight system which acts both in upward and downward
direction so that net load acts on the bearing. The issues in feeding
the lubricant into the bearing from the inlet side and preventing the
leakage of the lubricant is discussed. The application of the load on
the test bearing while maintaining the bearing afloat is also discussed.
Abstract: It is necessary to manage the fatigue crack growth (FCG) once those cracks are detected during in-service inspections. In this paper, a simulation program (FCG-System) is developed utilizing the commercial software ABAQUS with its object-oriented programming interface to simulate the fatigue crack path and to compute the corresponding fatigue life. In order to apply FCG-System in large-scale marine structures, the substructure modeling technique is integrated in the system under the consideration of structural details and load shedding during crack growth. Based on the nodal forces and nodal displacements obtained from finite element analysis, a formula for shell elements to compute stress intensity factors is proposed in the view of virtual crack closure technique. The cracks initiating from the intersection of flange and the end of the web-stiffener are investigated for fatigue crack paths and growth lives under water pressure loading and axial force loading, separately. It is found that the FCG-System developed by authors could be an efficient tool to perform fatigue crack growth analysis on marine structures.
Abstract: The process of thermoforming a carbon fiber reinforced thermoplastic (CFRTP) has increased its presence in the automotive industry for its wide applicability to the mass production car. A non-isothermal forming for CFRTP can shorten its cycle time to less than 1 minute. In this paper, the textile reinforcement FE model which the authors proposed in a previous work is extended to the CFRTP model for non-isothermal forming simulation. The effect of thermoplastic is given by adding shell elements which consider thermal effect to the textile reinforcement model. By applying Reuss model to the stress calculation of thermoplastic, the proposed model can accurately predict in-plane shear behavior, which is the key deformation mode during forming, in the range of the process temperature. Using the proposed model, thermoforming simulation was conducted and the results are in good agreement with the experimental results.
Abstract: The analysis and design of thin shell structures is a topic of interest in a variety of engineering applications. In structural mechanics problems the analyst seeks to determine the distribution of stresses throughout the structure to be designed. It is also necessary to calculate the displacements of certain points of the structure to ensure that specified allowable values are not exceeded. In this paper a comparative study between displacement and strain based finite elements applied to the analysis of some thin shell structures is presented. The results obtained from some examples show the efficiency and the performance of the strain based approach compared to the well known displacement formulation.
Abstract: The design of an optimised horizontal axis 5-meter-long wind turbine rotor blade in according with IEC 61400-2 standard is a research and development project in order to fulfil the requirements of high efficiency of torque from wind production and to optimise the structural components to the lightest and strongest way possible. For this purpose, a research study is presented here by focusing on the structural characteristics of a composite wind turbine blade via finite element modelling and analysis tools. In this work, first, the required data regarding the general geometrical parts are gathered. Then, the airfoil geometries are created at various sections along the span of the blade by using CATIA software to obtain the two surfaces, namely; the suction and the pressure side of the blade in which there is a hat shaped fibre reinforced plastic spar beam, so-called chassis starting at 0.5m from the root of the blade and extends up to 4 m and filled with a foam core. The root part connecting the blade to the main rotor differential metallic hub having twelve hollow threaded studs is then modelled. The materials are assigned as two different types of glass fabrics, polymeric foam core material and the steel-balsa wood combination for the root connection parts. The glass fabrics are applied using hand wet lay-up lamination with epoxy resin as METYX L600E10C-0, is the unidirectional continuous fibres and METYX XL800E10F having a tri-axial architecture with fibres in the 0,+45,-45 degree orientations in a ratio of 2:1:1. Divinycell H45 is used as the polymeric foam. The finite element modelling of the blade is performed via MSC PATRAN software with various meshes created on each structural part considering shell type for all surface geometries, and lumped mass were added to simulate extra adhesive locations. For the static analysis, the boundary conditions are assigned as fixed at the root through aforementioned bolts, where for dynamic analysis both fixed-free and free-free boundary conditions are made. By also taking the mesh independency into account, MSC NASTRAN is used as a solver for both analyses. The static analysis aims the tip deflection of the blade under its own weight and the dynamic analysis comprises normal mode dynamic analysis performed in order to obtain the natural frequencies and corresponding mode shapes focusing the first five in and out-of-plane bending and the torsional modes of the blade. The analyses results of this study are then used as a benchmark prior to modal testing, where the experiments over the produced wind turbine rotor blade has approved the analytical calculations.
Abstract: In this era of globalization, adoption of technology is quite difficult for people with physical disabilities compared to people with normal abilities. The advancement in mobile based accessible applications have opened up several different avenues for the visually challenged across the globe. Smartphones applications are not very common for blind people, but they access and use these applications in their daily lives to some extent. Several smartphone applications have a number of usability issues for the visually impaired. In this paper, we evaluate the usability of various android & iPhone applications for blind people through analysis and surveys. This paper aspires to provide guidance in order to increase smartphone application accessibility for the visually impaired. An abstract application design is also proposed to overcome usability issues in smartphone applications for visually challenged people.
Abstract: In this study, fish bone waste was used as a new
catalyst for biodiesel production. Instead of discarding the fish bone
waste, it will be utilized as a source for catalyst that can provide
significant benefit to the environment. Also, it can be substitute as a
calcium oxide source instead of using eggshell, crab shell and snail
shell. The XRD and SEM analysis proved that calcined fish bone
contains calcium oxide, calcium phosphate and hydroxyapatite. The
catalyst was characterized using Scanning Electron Microscope
(SEM) and X-ray Diffraction (XRD).
Abstract: The objectives of this research were to design and develop foot massage plate from coconut shell. The research investigated on the satisfaction of the users on the developed foot massage plate on 4 aspects; usage, practical in use, safety, and materials & production process. The sample group included 64 people joining the service at Wat Paitan Health Center, Bangkok. The samples were randomly tried on the massage plate and evaluated according to the 4 aspects. The data were analyzed to find mean, percentage, and standard deviation. The result showed that the overall satisfaction was at good level (mean = 3.80). When considering in details, it was found that the subjects reported their highest satisfaction on the practical usage (mean = 4.16), followed by safety (mean = 3.82); then, materials and production process (mean = 3.78). The least satisfaction aspect was on function and usage (mean = 3.45) or moderate level.
Abstract: This research was the experimental research. Its purpose was to find out how coconut shells can be adapted to be equipment for foot and calf reflexology. The sample group was 58 female street vendors in Thewet Market, Bangkok, selected by selection criteria and voluntary. The data collecting tool was the Visual Analogue Scale. The massaging tool made from coconut shells was the key equipment for this research. The research team assessed the level of exhaustion and heart rate among sample group before and after the massage, then analyzed the data by mean, standard deviation and paired sample t-test.
We found out from the research that
The level of exhaustion decreased 4.529 levels after the massage and the standard deviation was 1.6195. The heart rates went down 11.67 times/minute and the standard deviation was 6.742.
The level of exhaustion and heart rate after the massage decreased with the statistically significance at 0.01
Abstract: Palm kernel shell is an important bioenergy resource
in Thailand. However, due to elevated alkali content in biomass ash,
this oil palm residue shows high tendency to bed agglomeration in a
fluidized-bed combustion system using conventional bed material
(silica sand). In this study, palm kernel shell was burned in the
conical fluidized-bed combustor (FBC) using alumina and dolomite
as alternative bed materials to prevent bed agglomeration. For each
bed material, the combustion tests were performed at 45kg/h fuel feed
rate with excess air within 20–80%. Experimental results revealed
rather weak effects of the bed material type but substantial influence
of excess air on the behavior of temperature, O2, CO, CxHy, and NO
inside the reactor, as well as on the combustion efficiency and major
gaseous emissions of the conical FBC. The optimal level of excess air
ensuring high combustion efficiency (about 98.5%) and acceptable
level of the emissions was found to be about 40% when using
alumina and 60% with dolomite. By using these alternative bed
materials, bed agglomeration can be prevented when burning the
shell in the proposed conical FBC. However, both bed materials
exhibited significant changes in their morphological, physical and
chemical properties in the course of the time.
Abstract: The calcarenites carbonate rocks of the Quaternary ridges, which extend along the northwestern Mediterranean coastal plain of Egypt, represent an excellent model for the transformation of loose sediments to real sedimentary rocks by the different stages of meteoric diagenesis. The depositional and diagenetic fabrics of the rocks, in addition to the strata orientation, highly affect their ultimate compressive strength and other geotechnical properties.
There is a marked increase in the compressive strength (UCS) from the first to the fourth ridge rock samples. The lowest values are related to the loose packing, weakly cemented aragonitic ooid sediments with high porosity, besides the irregularly distributed of cement, which result in decreasing the ability of these rocks to withstand crushing under direct pressure. The high (UCS) values are attributed to the low porosity, the presence of micritic cement, the reduction in grain size and the occurrence of micritization and calcretization processes.
The strata orientation has a notable effect on the measured (UCS). The lowest values have been recorded for the samples cored in the inclined direction; whereas the highest values have been noticed in most samples cored in the vertical and parallel directions to bedding plane. In case of the inclined direction, the bedding planes were oriented close to the plane of maximum shear stress. The lowest and highest anisotropy values have been recorded for the first and the third ridges rock samples, respectively, which may attributed to the relatively homogeneity and well sorted grainstone of the first ridge rock samples, and relatively heterogeneity in grain and pore size distribution and degree of cementation of the third ridge rock samples, besides, the abundance of shell fragments with intraparticle pore spaces, which may produce lines of weakness within the rock.
Abstract: This paper presents experimental investigation carried out on an unmodified four stroke diesel engine running with preheated straight vegetable oil (SVO) of Karanja. The viscosity of straight karanja oil was reduced by preheating the oil up to 1600C under different load condition. The preheating was done with the help of a Shell and Tube heat exchanger equipment without using any external power source. The heat exchanger was designed in the lab and the heating source was by waste exhaust gas from engine. The experimental results data were analyzed by using 20% blends of svo of Karanja with 80% diesel by volume and 100% preheated svo of karanja for various parameters like specific fuel consumption, brake thermal efficiency and emission of exhaust gas like CO, CO2, HC and NOx. The results indicated that by using straight karanja oil, the emission parameter increases as compared to diesel but regarding engine performance it was found to be very close to that of diesel. All total it can be a replacement of diesel with a small efficiency drop.
Abstract: The waste agriculture materials cause environment pollution, recycle of these materials help sustainable development. This study focused on the impact of used oil palm shell ash on the compressive and flexural strengths of cement mortar. Two different cement mortar mixes have been designed to investigate the impact of oil palm shell ash on strengths of cement mortar. Quantity of 4% oil palm shell ash has been replaced in cement mortar. The main objective of this paper is, to modify mechanical properties of cement mortar by replacement of oil palm ash in it at early age of 7 days. The results have been revealed optimum quantity of oil palm ash for replacement in cement mortar. The deflection, load to failure, time to failure of compressive strength and flexural strength of all specimens have significantly been improved. The stress-strain behavior has been indicated ability of modified cement mortar in control stress path and strain. The micro property of cement paste has not been investigated.
Abstract: Many synthetic additives have been using for improve cement mortar and concrete characteristics, but natural additive is a friendly environment option. The quantity of (2% and 4%) seashell powder has been replaced in cement mortar, and compared with plain cement mortar in early age of 7 days. The strain gauges have been installed on beams and cube, for monitoring fluctuation of flexural and compressive strength. Main objective of this paper is to study effect of linear static force on flexural and compressive strength of modified cement mortar. The results have been indicated that the replacement of appropriate proportion of seashell powder enhances cement mortar mechanical properties. The replacement of 2% seashell causes improvement of deflection, time to failure and maximum load to failure on concrete beam and cube, the same occurs for compressive modulus elasticity. Increase replacement of seashell to 4% reduces all flexural strength, compressive strength and strain of cement mortar.