Abstract: This paper presents a physics-based model for the
high-voltage fast recovery diodes. The model provides a good
trade-off between reverse recovery time and forward voltage drop
realized through a combination of lifetime control and emitter
efficiency reduction techniques. The minority carrier lifetime can be
extracted from the reverse recovery transient response and forward
characteristics. This paper also shows that decreasing the amount of
the excess carriers stored in the drift region will result in softer
characteristics which can be achieved using a lower doping level. The
developed model is verified by experiment and the measurement data
agrees well with the model.
Abstract: In this work, biohydrogen production via dark
fermentation from alcohol wastewater using upflow anaerobic sludge
blanket reactors (UASB) with a working volume of 4 L was
investigated to find the optimum conditions for a maximum hydrogen
yield. The system was operated at different COD loading rates (23,
31, 46 and 62 kg/m3d) at mesophilic temperature (37 ºC) and pH 5.5.
The seed sludge was pretreated before being fed to the UASB system
by boiling at 95 ºC for 15 min. When the system was operated under
the optimum COD loading rate of 46 kg/m3d, it provided the
hydrogen content of 27%, hydrogen yield of 125.1 ml H2/g COD
removed and 95.1 ml H2/g COD applied, hydrogen production rate of
18 l/d, specific hydrogen production rate of 1080 ml H2/g MLVSS d
and 1430 ml H2/ L d, and COD removal of 24%.
Abstract: Cements, which are intrinsically brittle materials, can
exhibit a degree of pseudo-ductility when reinforced with a sufficient
volume fraction of a fibrous phase. This class of materials, called
Engineered Cement Composites (ECC) has the potential to be used in
future tunneling applications where a level of pseudo-ductility is
required to avoid brittle failures. However uncertainties remain
regarding mechanical performance. Previous work has focused on
comparatively thin specimens; however for future civil engineering
applications, it is imperative that the behavior in tension of thicker
specimens is understood. In the present work, specimens containing
cement powder and admixtures have been manufactured following
two different processes and tested in tension. Multiple matrix
cracking has been observed during tensile testing, leading to a
“strain-hardening" behavior, confirming the possible suitability of
ECC material when used as thick sections (greater than 50mm) in
tunneling applications.
Abstract: Mobile Ad Hoc Networks (MANETs) are multi-hop
wireless networks in which all nodes cooperatively maintain network
connectivity. In such a multi-hop wireless network, every node may
be required to perform routing in order to achieve end-to-end
communication among nodes. These networks are energy constrained
as most ad hoc mobile nodes today operate with limited battery
power. Hence, it is important to minimize the energy consumption of
the entire network in order to maximize the lifetime of ad hoc
networks. In this paper, a mechanism involving the integration of
load balancing approach and transmission power control approach is
introduced to maximize the life-span of MANETs. The mechanism is
applied on Ad hoc On-demand Vector (AODV) protocol to make it
as energy aware AODV (EA_AODV). The simulation is carried out
using GloMoSim2.03 simulator. The results show that the proposed
mechanism reduces the average required transmission energy per
packet compared to the standard AODV.
Abstract: A new data fusion method called joint probability density matrix (JPDM) is proposed, which can associate and fuse measurements from spatially distributed heterogeneous sensors to identify the real target in a surveillance region. Using the probabilistic grids representation, we numerically combine the uncertainty regions of all the measurements in a general framework. The NP-hard multisensor data fusion problem has been converted to a peak picking problem in the grids map. Unlike most of the existing data fusion method, the JPDM method dose not need association processing, and will not lead to combinatorial explosion. Its convergence to the CRLB with a diminishing grid size has been proved. Simulation results are presented to illustrate the effectiveness of the proposed technique.
Abstract: Quality control is the crucial step for ISO 9001
Quality System Management Standard for companies. While
measuring the quality level of both raw material and semi
product/product, the calibration of the measuring device is an
essential requirement. Calibration suppliers are in the service sector
and therefore the calibration supplier selection is becoming a worthy
topic for improving service quality.
This study presents the results of a questionnaire about the
selection criteria of a calibration supplier. The questionnaire was
applied to 103 companies and the results are discussed in this paper.
The analysis was made with MINITAB 14.0 statistical programs.
“Competence of documentations" and “technical capability" are
defined as the prerequisites because of the ISO/IEC17025:2005
standard. Also “warranties and complaint policy", “communication",
“service features", “quality" and “performance history" are defined as
very important criteria for calibration supplier selection.
Abstract: We intend to point out the differences which exist
between the classical Gini concentration coefficient and a proposed
bipolarization index defined for an arbitrary random variable which
have a finite support.
In fact Gini's index measures only the "poverty degree" for the
individuals from a given population taking into consideration their
wages. The Gini coefficient is not so sensitive to the significant
income variations in the "rich people class" .
In practice there are multiple interdependent relations between the
pauperization and the socio-economical polarization phenomena. The
presence of a strong pauperization aspect inside the population
induces often a polarization effect in this society. But the
pauperization and the polarization phenomena are not identical. For
this reason it isn't always adequate to use a Gini type coefficient,
based on the Lorenz order, to estimate the bipolarization level of the
individuals from the studied population.
The present paper emphasizes these ideas by considering two
families of random variables which have a linear or a triangular type
distributions. In addition, the continuous variation, depending on the
parameter "time" of the chosen distributions, could simulate a real
dynamical evolution of the population.
Abstract: Recently, analysis and designing of the structures
based on the Reliability theory have been the center of attention.
Reason of this attention is the existence of the natural and random
structural parameters such as the material specification, external
loads, geometric dimensions etc. By means of the Reliability theory,
uncertainties resulted from the statistical nature of the structural
parameters can be changed into the mathematical equations and the
safety and operational considerations can be considered in the
designing process. According to this theory, it is possible to study the
destruction probability of not only a specific element but also the
entire system. Therefore, after being assured of safety of every
element, their reciprocal effects on the safety of the entire system can
be investigated.
Abstract: Functioning of a biometric system in large part
depends on the performance of the similarity measure function.
Frequently a generalized similarity distance measure function such as
Euclidian distance or Mahalanobis distance is applied to the task of
matching biometric feature vectors. However, often accuracy of a
biometric system can be greatly improved by designing a customized
matching algorithm optimized for a particular biometric application.
In this paper we propose a tailored similarity measure function for
behavioral biometric systems based on the expert knowledge of the
feature level data in the domain. We compare performance of a
proposed matching algorithm to that of other well known similarity
distance functions and demonstrate its superiority with respect to the
chosen domain.
Abstract: Logic based methods for learning from structured data
is limited w.r.t. handling large search spaces, preventing large-sized
substructures from being considered by the resulting classifiers. A
novel approach to learning from structured data is introduced that
employs a structure transformation method, called finger printing, for
addressing these limitations. The method, which generates features
corresponding to arbitrarily complex substructures, is implemented in
a system, called DIFFER. The method is demonstrated to perform
comparably to an existing state-of-art method on some benchmark
data sets without requiring restrictions on the search space.
Furthermore, learning from the union of features generated by finger
printing and the previous method outperforms learning from each
individual set of features on all benchmark data sets, demonstrating
the benefit of developing complementary, rather than competing,
methods for structure classification.
Abstract: Modern culture, based on disinhibition of cultural trends and on heterodirection, is promoting openmindedness attitudes towards ethnic diversity, but on the other hand also new forms of social representations of the foreigner. Social representation is situated between the psychic field and the social one; it is the representation of oneself and of the other one, hanging between social categories and individual inner world. We will produce the results of a research on the representation of the foreigner, built on the type of prejudice prevailing among middle-low or middle-high educational qualification subjects, in which prejudicial attitudes seem to descend from precise mental images of the foreigner.
Abstract: The possible therapeutic effect of cannabidiol, the major non-psychotropic Cannabis constituent, was investigated against acute hepatotoxicity induced by a single oral dose of acetaminophen (500mg/kg) in mice. Cannabidiol (two intraperitoneal injections, 5mg/kg, each) was given 1 hour and 12 hours following acetaminophen administration. Acetaminophen administration caused significant elevations of serum alanine aminotransferase, and hepatic malondialdehyde, and nitric oxide levels, and a significant decrease in hepatic reduced glutathione. Cannabidiol significantly attenuated the deterioration in the measured biochemical parameters resulted from acetaminophen administration. Also, histopathological examination showed that cannabidiol markedly attenuated ameliorated acetaminophen-induced liver tissue damage. These results emphasize that cannabidiol represents a potential therapeutic option to protect against acetaminophen hepartotoxicity which is a common clinical problem.
Abstract: Supersonic open and closed cavity flows are investigated experimentally and computationally. Free stream Mach number of two is set. Schlieren imaging is used to visualise the flow behaviour showing stark differences between open and closed. Computational Fluid Dynamics (CFD) is used to simulate open cavity of flow with aspect ratio of 4. A rear wall treatment is implemented in order to pursue a simple passive control approach. Good qualitative agreement is achieved between the experimental flow visualisation and the CFD in terms of the expansion-shock waves system. The cavity oscillations are shown to be dominated by the first and third Rossister modes combining to high fluctuations of non-linear nature above the cavity rear edge. A simple rear wall treatment in terms of a hole shows mixed effect on the flow oscillations, RMS contours, and time history density fluctuations are given and analysed.
Abstract: The distillation process in the general sense is a
relatively simple technique from the standpoints of its principles.
When dedicating distillation to water treatment and specifically
producing fresh water from sea, ocean and/ briny waters it is
interesting to notice that distillation has no limitations or domains of
applicability regarding the nature or the type of the feedstock water.
This is not the case however for other techniques that are
technologically quite complex, necessitate bigger capital investments
and are limited in their usability. In a previous paper we have
explored some of the effects of temperature on yield. In this paper,
we continue building onto that knowledge base and focus on the
effects of several additional engineering and design variables on
productivity.
Abstract: This paper presents a fuzzy control system for a three degree of freedom (3-DOF) stabilized platform with explicit decoupling scheme. The system under consideration is a system with strong interactions between three channels. By using the concept of decentralized control, a control structure is developed that is composed of three control loops, each of which is associated with a single-variable fuzzy controller and a decoupling unit. Takagi-Sugeno (TS) fuzzy control algorithm is used to implement the fuzzy controller. The decoupling units design is based on the adaptive theory reasoning. Simulation tests were established using Simulink of Matlab. The obtained results have demonstrated the feasibility and effectiveness of the proposed approach. Simulation results are represented in this paper.
Abstract: In this paper, we deal with finite projective Klingenberg plane M (A) coordinatized by local ring A := Zq+Zq E (where prime power q = p', e0 Z q and 62 = 0). So, we get some combinatorical results on 6-figures. For example, we show that there exist p — 1 6-figure classes in M(A).
Abstract: Well-developed strategic marketing planning is the essential
prerequisite for establishment of the right and unique competitive
advantage. Typical market, however, is a heterogeneous
and decentralized structure with natural involvement of individual
or group subjectivity and irrationality. These features cannot be
fully expressed with one-shot rigorous formal models based on,
e.g. mathematics, statistics or empirical formulas. We present an
innovative solution, extending the domain of agent based computational
economics towards the concept of hybrid modeling in service
provider and consumer market such as telecommunications. The
behavior of the market is described by two classes of agents -
consumer and service provider agents - whose internal dynamics
are fundamentally different. Customers are rather free multi-state
structures, adjusting behavior and preferences quickly in accordance
with time and changing environment. Producers, on the contrary,
are traditionally structured companies with comparable internal processes
and specific managerial policies. Their business momentum is
higher and immediate reaction possibilities limited. This limitation
underlines importance of proper strategic planning as the main
process advising managers in time whether to continue with more
or less the same business or whether to consider the need for future
structural changes that would ensure retention of existing customers
or acquisition of new ones.
Abstract: Climate change and environmental pressures are
major international issues nowadays. It is time when governments,
businesses and consumers have to respond through more
environmentally friendly and aware practices, products and policies.
This is the prime time to develop alternative sustainable construction
materials, reduce greenhouse gas emissions, save energy, look to
renewable energy sources and recycled materials, and reduce waste.
The utilization of waste materials (slag, fly ash, glass beads, plastic
and so on) in concrete manufacturing is significant due to its
engineering, financial, environmental and ecological benefits. Thus,
utilization of waste materials in concrete production is very much
helpful to reach the goal of the sustainable construction. Therefore,
this study intends to use glass beads in concrete production.
The paper reports on the performance of 9 different concrete
mixes containing different ratios of glass crushed to 5 mm - 20 mm
maximum size and glass marble of 20 mm size as coarse aggregate.
Ordinary Portland cement type 1 and fine sand less than 0.5 mm were
used to produce standard concrete cylinders. Compressive strength
tests were carried out on concrete specimens at various ages. Test
results indicated that the mix having the balanced ratio of glass beads
and round marbles possess maximum compressive strength which is
3889 psi, as glass beads perform better in bond formation but have
lower strength, on the other hand marbles are strong in themselves
but not good in bonding. These mixes were prepared following a
specific W/C and aggregate ratio; more strength can be expected to
achieve from different W/C, aggregate ratios, adding admixtures like
strength increasing agents, ASR inhibitor agents etc.
Abstract: Desert regions around the Nile valley in Upper Egypt
contain great extent of swelling soil. Many different comment
procedures of treatment of the swelling soils for construction such as
pre-swelling, load balance OR soil replacement. One of the measure
factors which affect the level of the aggressiveness of the swelling
soil is the direction of the infiltration water directions within the
swelling soils. In this paper a physical model was installed to
measure the effect of water on the swelling soil with replacement
using fatty acid distillation residuals (FADR) mixed with sand as
thick sand-FADR mixture to prevent the water pathway arrive to the
swelling soil. Testing program have been conducted on different
artificial samples with different sand to FADR contents ratios (4%,
6%, and 9%) to get the optimum value fulfilling the impermeable
replacement. The tests show that a FADR content of 9% is sufficient
to produce impermeable replacement.
Abstract: The Marangoni convective instability in a horizontal
fluid layer with the insoluble surfactant and nondeformable free
surface is investigated. The surface tension at the free surface is
linearly dependent on the temperature and concentration gradients.
At the bottom surface, the temperature conditions of uniform
temperature and uniform heat flux are considered. By linear stability
theory, the exact analytical solutions for the steady Marangoni
convection are derived and the marginal curves are plotted. The
effects of surfactant or elasticity number, Lewis number and Biot
number on the marginal Marangoni instability are assessed. The
surfactant concentration gradients and the heat transfer mechanism at
the free surface have stabilizing effects while the Lewis number
destabilizes fluid system. The fluid system with uniform temperature
condition at the bottom boundary is more stable than the fluid layer
that is subjected to uniform heat flux at the bottom boundary.