Abstract: The objective of this study is to investigate the
combustion in a pilot-ignited supercharged dual-fuel engine, fueled
with different types of gaseous fuels under various equivalence ratios.
It is found that if certain operating conditions are maintained,
conventional dual-fuel engine combustion mode can be transformed to
the combustion mode with the two-stage heat release. This mode of
combustion was called the PREMIER (PREmixed Mixture Ignition in
the End-gas Region) combustion. During PREMIER combustion,
initially, the combustion progresses as the premixed flame
propagation and then, due to the mixture autoignition in the end-gas
region, ahead of the propagating flame front, the transition occurs with
the rapid increase in the heat release rate.
Abstract: Applying a rigorous process to optimize the elements
of a supply-chain network resulted in reduction of the waiting time
for a service provider and customer. Different sources of downtime
of hydraulic pressure controller/calibrator (HPC) were causing
interruptions in the operations. The process examined all the issues to
drive greater efficiencies. The issues included inherent design issues
with HPC pump, contamination of the HPC with impurities, and the
lead time required for annual calibration in the USA.
HPC is used for mandatory testing/verification of formation
tester/pressure measurement/logging-while drilling tools by oilfield
service providers, including Halliburton.
After market study andanalysis, it was concluded that the current
HPC model is best suited in the oilfield industry. To use theexisting
HPC model effectively, design andcontamination issues were
addressed through design and process improvements. An optimum
network is proposed after comparing different supply-chain models
for calibration lead-time reduction.
Abstract: Minimum Quantity Lubrication (MQL) technique
obtained a significant attention in machining processes to reduce
environmental loads caused by usage of conventional cutting fluids.
Recently nanofluids are finding an extensive application in the field
of mechanical engineering because of their superior lubrication and
heat dissipation characteristics. This paper investigates the use of a
nanofluid under MQL mode to improve grinding characteristics of
Ti-6Al-4V alloy. Taguchi-s experimental design technique has been
used in the present investigation and a second order model has been
established to predict grinding forces and surface roughness.
Different concentrations of water based Al2O3 nanofluids were
applied in the grinding operation through MQL setup developed in
house and the results have been compared with those of conventional
coolant and pure water. Experimental results showed that grinding
forces reduced significantly when nano cutting fluid was used even at
low concentration of the nano particles and surface finish has been
found to improve with higher concentration of the nano particles.
Abstract: The paper presents a one-dimensional transient
mathematical model of compressible non-isothermal multicomponent
fluid mixture flow in a pipe. The set of the mass,
momentum and enthalpy conservation equations for gas phase is
solved in the model. Thermo-physical properties of multi-component
gas mixture are calculated by solving the Equation of State (EOS)
model. The Soave-Redlich-Kwong (SRK-EOS) model is chosen. Gas
mixture viscosity is calculated on the basis of the Lee-Gonzales-
Eakin (LGE) correlation. Numerical analysis of rapid gas
decompression process in rich and base natural gases is made on the
basis of the proposed mathematical model. The model is successfully
validated on the experimental data [1]. The proposed mathematical
model shows a very good agreement with the experimental data [1] in
a wide range of pressure values and predicts the decompression in
rich and base gas mixtures much better than analytical and
mathematical models, which are available from the open source
literature.
Abstract: Iran is one of the greatest producers of date in the
world. However due to lack of information about its viscoelastic
properties, much of the production downgraded during harvesting
and postharvesting processes. In this study the effect of temperature
and moisture content of product were investigated on stress
relaxation characteristics. Therefore, the freshly harvested date
(kabkab) at tamar stage were put in controlled environment chamber
to obtain different temperature levels (25, 35, 45, and 55 0C) and
moisture contents (8.5, 8.7, 9.2, 15.3, 20, 32.2 %d.b.). A texture
analyzer TAXT2 (Stable Microsystems, UK) was used to apply
uniaxial compression tests. A chamber capable to control temperature
was designed and fabricated around the plunger of texture analyzer to
control the temperature during the experiment. As a new approach a
CCD camera (A4tech, 30 fps) was mounted on a cylindrical glass
probe to scan and record contact area between date and disk.
Afterwards, pictures were analyzed using image processing toolbox
of Matlab software. Individual date fruit was uniaxially compressed
at speed of 1 mm/s. The constant strain of 30% of thickness of date
was applied to the horizontally oriented fruit. To select a suitable
model for describing stress relaxation of date, experimental data were
fitted with three famous stress relaxation models including the
generalized Maxwell, Nussinovitch, and Pelege. The constant in
mentioned model were determined and correlated with temperature
and moisture content of product using non-linear regression analysis.
It was found that Generalized Maxwell and Nussinovitch models
appropriately describe viscoelastic characteristics of date fruits as
compared to Peleg mode.
Abstract: This paper presents a Neural Network (NN) identification of icing parameters in an A340 aircraft and a reconfiguration technique to keep the A/C performance close to the performance prior to icing. Five aircraft parameters are assumed to be considerably affected by icing. The off-line training for identifying the clear and iced dynamics is based on the Levenberg-Marquard Backpropagation algorithm. The icing parameters are located in the system matrix. The physical locations of the icing are assumed at the right and left wings. The reconfiguration is based on the technique known as the control mixer approach or pseudo inverse technique. This technique generates the new control input vector such that the A/C dynamics is not much affected by icing. In the simulations, the longitudinal and lateral dynamics of an Airbus A340 aircraft model are considered, and the stability derivatives affected by icing are identified. The simulation results show the successful NN identification of the icing parameters and the reconfigured flight dynamics having the similar performance before the icing. In other words, the destabilizing icing affect is compensated.
Abstract: Intercropping is one of the sustainable agricultural
factors. The SPAD meter can be used to predict nitrogen index
reliably, it may also be a useful tool for assessing the relative impact
of weeds on crops. In order to study the effect of weeds on SPAD in
corn (Zea mays L.), sweet basil (Ocimum basilicum L.) and borage
(Borago officinalis L.) in intercropping system, a factorial experiment
was conducted in three replications in 2011. Experimental factors
were included intercropping of corn with sweet basil and borage in
different ratios (100:0, 75:25, 50:50, 25:75 and 0:100 corn: borage or
sweet basil) and weed infestation (weed control and weed
interference). The results showed that intercropping of corn with
sweet basil and borage increased the SPAD value of corn compare to
monoculture in weed interference condition. Sweet basil SPAD value
in weed control treatments (43.66) was more than weed interference
treatments (40.17). Corn could increase the borage SPAD value
compare to monoculture in weed interference treatments.
Abstract: In this paper we address a multi-objective scheduling problem for unrelated parallel machines. In unrelated parallel systems, the processing cost/time of a given job on different machines may vary. The objective of scheduling is to simultaneously determine the job-machine assignment and job sequencing on each machine. In such a way the total cost of the schedule is minimized. The cost function consists of three components, namely; machining cost, earliness/tardiness penalties and makespan related cost. Such scheduling problem is combinatorial in nature. Therefore, a Simulated Annealing approach is employed to provide good solutions within reasonable computational times. Computational results show that the proposed approach can efficiently solve such complicated problems.
Abstract: This paper discusses a new model of Islamic code of
ethics for directors. Several corporate scandals and local (example
Transmile and Megan Media) and overseas corporate (example
Parmalat and Enron) collapses show that the current corporate
governance and regulatory reform are unable to prevent these events
from recurring. Arguably, the code of ethics for directors is under
research and the current code of ethics only concentrates on binding
the work of the employee of the organization as a whole, without
specifically putting direct attention to the directors, the group of
people responsible for the performance of the company. This study
used a semi-structured interview survey of well-known Islamic
scholars such as the Mufti to develop the model. It is expected that
the outcome of the research is a comprehensive model of code of
ethics based on the Islamic principles that can be applied and used by
the company to construct a code of ethics for their directors.
Abstract: The software industry has been considered a critical
infrastructure for any nation. Several studies have indicated that
national competitiveness increasingly depends upon Information and
Communication Technology (ICT), and software is one of the major
components of ICT, important for both large and small enterprises.
Even though there has been strong growth in the software industry in
Thailand, the industry has faced many challenges and problems that
need to be resolved. For example, the amount of pirated software has
been rising, and Thailand still has a large gap in the digital divide.
Additionally, the adoption among SMEs has been slow. This paper
investigates various issues in the software industry in Thailand, using
information acquired through analysis of secondary sources,
observation, and focus groups. The results of this study can be used
as “lessons learned" for the development of the software industry in
any developing country.
Abstract: Active vibration control is an important problem in
structures. The objective of active vibration control is to reduce the vibrations of a system by automatic modification of the system-s
structural response. In this paper, the modeling and design of a fast
output sampling feedback controller for a smart flexible beam system embedded with shear sensors and actuators for SISO system using
Timoshenko beam theory is proposed. FEM theory, Timoshenko beam theory and the state space techniques are used to model the
aluminum cantilever beam. For the SISO case, the beam is divided into 5 finite elements and the control actuator is placed at finite
element position 1, whereas the sensor is varied from position 2 to 5, i.e., from the nearby fixed end to the free end. Controllers are
designed using FOS method and the performance of the designed FOS controller is evaluated for vibration control for 4 SISO models
of the same plant. The effect of placing the sensor at different locations on the beam is observed and the performance of the
controller is evaluated for vibration control. Some of the limitations of the Euler-Bernoulli theory such as the neglection of shear and
axial displacement are being considered here, thus giving rise to an accurate beam model. Embedded shear sensors and actuators have
been considered in this paper instead of the surface mounted sensors
and actuators for vibration suppression because of lot of advantages. In controlling the vibration modes, the first three dominant modes of
vibration of the system are considered.
Abstract: In this research, the use of light beam size to design the adjustable mirror bender is presented. The focused beam line characterized by its size towards the synchrotron light beam line is investigated. The COSMOSWorks is used in all simulation components of curvature adjustment system to analyze in finite element method. The results based on simulation covers the use of applied forces during adjustment of the mirror radius are presented.
Abstract: In this paper, based on the past project cost and time
performance, a model for forecasting project cost performance is
developed. This study presents a probabilistic project control concept
to assure an acceptable forecast of project cost performance. In this
concept project activities are classified into sub-groups entitled
control accounts. Then obtain the Stochastic S-Curve (SS-Curve), for
each sub-group and the project SS-Curve is obtained by summing
sub-groups- SS-Curves. In this model, project cost uncertainties are
considered through Beta distribution functions of the project
activities costs required to complete the project at every selected time
sections through project accomplishment, which are extracted from a
variety of sources. Based on this model, after a percentage of the
project progress, the project performance is measured via Earned
Value Management to adjust the primary cost probability distribution
functions. Then, accordingly the future project cost performance is
predicted by using the Monte-Carlo simulation method.
Abstract: Principle component analysis is often combined with
the state-of-art classification algorithms to recognize human faces.
However, principle component analysis can only capture these
features contributing to the global characteristics of data because it is a
global feature selection algorithm. It misses those features
contributing to the local characteristics of data because each principal
component only contains some levels of global characteristics of data.
In this study, we present a novel face recognition approach using
non-negative principal component analysis which is added with the
constraint of non-negative to improve data locality and contribute to
elucidating latent data structures. Experiments are performed on the
Cambridge ORL face database. We demonstrate the strong
performances of the algorithm in recognizing human faces in
comparison with PCA and NREMF approaches.
Abstract: This paper and its companion (Part 2) deal with
modeling and optimization of two NP-hard problems in production
planning of flexible manufacturing system (FMS), part type selection
problem and loading problem. The part type selection problem and
the loading problem are strongly related and heavily influence the
system-s efficiency and productivity. The complexity of the problems
is harder when flexibilities of operations such as the possibility of
operation processed on alternative machines with alternative tools are
considered. These problems have been modeled and solved
simultaneously by using real coded genetic algorithms (RCGA)
which uses an array of real numbers as chromosome representation.
These real numbers can be converted into part type sequence and
machines that are used to process the part types. This first part of the
papers focuses on the modeling of the problems and discussing how
the novel chromosome representation can be applied to solve the
problems. The second part will discuss the effectiveness of the
RCGA to solve various test bed problems.
Abstract: Improving performance measures in the construction
processes has been a major concern for managers and decision
makers in the industry. They seek for ways to recognize the key
factors which have the largest effect on the process. Identifying such
factors can guide them to focus on the right parts of the process in
order to gain the best possible result. In the present study design of
experiment (DOE) has been applied to a computer simulation model
of brick laying process to determine significant factors while
productivity has been chosen as the response of the experiment. To
this end, four controllable factors and their interaction have been
experimented and the best factor level has been calculated for each
one. The results indicate that three factors, namely, labor of brick,
labor of mortar and inter arrival time of mortar along with interaction
of labor of brick and labor of mortar are significant.
Abstract: Radio propagation from point-to-point is affected by
the physical channel in many ways. A signal arriving at a destination
travels through a number of different paths which are referred to as
multi-paths. Research in this area of wireless communications has
progressed well over the years with the research taking different
angles of focus. By this is meant that some researchers focus on
ways of reducing or eluding Multipath effects whilst others focus on
ways of mitigating the effects of Multipath through compensation
schemes. Baseband processing is seen as one field of signal
processing that is cardinal to the advancement of software defined
radio technology. This has led to wide research into the carrying out
certain algorithms at baseband. This paper considers compensating
for Multipath for Frequency Modulated signals. The compensation
process is carried out at Radio frequency (RF) and at Quadrature
baseband (QBB) and the results are compared. Simulations are
carried out using MatLab so as to show the benefits of working at
lower QBB frequencies than at RF.
Abstract: The paper presents an optimization study based on
genetic algorithms (GA-s) for a radio-frequency applicator used in
heating dielectric band products. The weakly coupled electro-thermal
problem is analyzed using 2D-FEM. The design variables in the
optimization process are: the voltage of a supplementary “guard"
electrode and six geometric parameters of the applicator. Two
objective functions are used: temperature uniformity and total active
power absorbed by the dielectric. Both mono-objective and multiobjective
formulations are implemented in GA optimization.
Abstract: Heart disease (HD) is a major cause of morbidity and mortality in the modern society. Medical diagnosis is an important but complicated task that should be performed accurately and efficiently and its automation would be very useful. All doctors are unfortunately not equally skilled in every sub specialty and they are in many places a scarce resource. A system for automated medical diagnosis would enhance medical care and reduce costs. In this paper, a new approach based on coactive neuro-fuzzy inference system (CANFIS) was presented for prediction of heart disease. The proposed CANFIS model combined the neural network adaptive capabilities and the fuzzy logic qualitative approach which is then integrated with genetic algorithm to diagnose the presence of the disease. The performances of the CANFIS model were evaluated in terms of training performances and classification accuracies and the results showed that the proposed CANFIS model has great potential in predicting the heart disease.
Abstract: Owing to extensive use of hydrogen in refining or
petrochemical units, it is essential to manage hydrogen network in
order to make the most efficient utilization of hydrogen. On the other
hand, hydrogen is an important byproduct not properly used through
petrochemical complexes and mostly sent to the fuel system. A few
works have been reported in literature to improve hydrogen network
for petrochemical complexes. In this study a comprehensive analysis
is carried out on petrochemical units using a modified automated
targeting technique which is applied to determine the minimum
hydrogen consumption. Having applied the modified targeting
method in two petrochemical cases, the results showed a significant
reduction in required fresh hydrogen.