Abstract: This paper presents a part of research on the
rheological properties of bitumen modified by thermoplastic namely
linear low density polyethylene (LLDPE), high density polyethylene
(HDPE) and polypropylene (PP) and its interaction with 80 pen base
bitumen. As it is known that the modification of bitumen by the use
of polymers enhances its performance characteristics but at the same
time significantly alters its rheological properties. The rheological
study of polymer modified bitumen (PMB) was made through
penetration, ring & ball softening point and viscosity test. The results
were then related to the changes in the rheological properties of
polymer modified bitumen. It was observed that thermoplastic
copolymer shows profound effect on penetration rather than
softening point. The viscoelastic behavior of polymer modified
bitumen depend on the concentration of polymer, mixing
temperature, mixing technique, solvating power of base bitumen and
molecular structure of polymer used. PP offer better blend in
comparison to HDPE and LLDPE. The viscosity of base bitumen was
also enhanced with the addition of polymer. The pseudoplastic
behavior was more prominent for HDPE and LLDPE than PP. Best
results were obtained when polymer concentration was kept below
3%
Abstract: In this paper, a predator-prey model with time delay and habitat complexity is investigated. By analyzing the characteristic equations, the local stability of each feasible equilibria of the system is discussed and the existence of a Hopf bifurcation at the coexistence equilibrium is established. By choosing the sum of two delays as a bifurcation parameter, we show that Hopf bifurcations can occur as crosses some critical values. By deriving the equation describing the flow on the center manifold, we can determine the direction of the Hopf bifurcations and the stability of the bifurcating periodic solutions. Numerical simulations are carried out to illustrate the main theoretical results.
Abstract: Optical properties of sputter-deposited ZnS thin films
were investigated as potential replacements for CBD(chemical bath
deposition) CdS buffer layers in the application of CIGS solar cells.
ZnS thin films were fabricated on glass substrates at RT, 150oC, 200oC,
and 250oC with 50 sccm Ar gas using an RF magnetron sputtering
system. The crystal structure of the thin film is found to be zinc blende
(cubic) structure. Lattice parameter of ZnS is slightly larger than CdS
on the plane and thus better matched with that of CIGS. Within a
400-800 nm wavelength region, the average transmittance was larger
than 75%. When the deposition temperature of the thin film was
increased, the blue shift phenomenon was enhanced. Band gap energy
of the ZnS thin film tended to increase as the deposition temperature
increased. ZnS thin film is a promising material system for the CIGS
buffer layer, in terms of ease of processing, low cost, environmental
friendliness, higher transparency, and electrical properties
Abstract: Measurement of the quality of image compression is important for image processing application. In this paper, we propose an objective image quality assessment to measure the quality of gray scale compressed image, which is correlation well with subjective quality measurement (MOS) and least time taken. The new objective image quality measurement is developed from a few fundamental of objective measurements to evaluate the compressed image quality based on JPEG and JPEG2000. The reliability between each fundamental objective measurement and subjective measurement (MOS) is found. From the experimental results, we found that the Maximum Difference measurement (MD) and a new proposed measurement, Structural Content Laplacian Mean Square Error (SCLMSE), are the suitable measurements that can be used to evaluate the quality of JPEG200 and JPEG compressed image, respectively. In addition, MD and SCLMSE measurements are scaled to make them equivalent to MOS, given the rate of compressed image quality from 1 to 5 (unacceptable to excellent quality).
Abstract: In this article we explore how computer assisted exercises may allow for bridging the traditional gap between theory and practice in professional education. To educate officers able to master the complexity of the battlefield the Norwegian Military Academy needs to develop a learning environment that allows for creating viable connections between the educational environment and the field of practice. In response to this challenge we explore the conditions necessary to make computer assisted training systems (CATS) a useful tool to create structural similarities between an educational context and the field of military practice. Although, CATS may facilitate work procedures close to real life situations, this case do demonstrate how professional competence also must build on viable learning theories and environments. This paper explores the conditions that allow for using simulators to facilitate professional competence from within an educational setting. We develop a generic didactic model that ascribes learning to participation in iterative cycles of action and reflection. The development of this model is motivated by the need to develop an interdisciplinary professional education rooted in the pattern of military practice.
Abstract: During recent years, the traditional learning
approaches have undergone fundamental changes due to the
emergence of new technologies such as multimedia, hypermedia and
telecommunication. E-learning is a modern world phenomenon that
has come into existence in the information age and in a knowledgebased
society. E-learning has developed significantly within a short
period of time. Thus it is of a great significant to secure information,
allow a confident access and prevent unauthorized accesses. Making
use of individuals- physiologic or behavioral (biometric) properties is
a confident method to make the information secure. Among the
biometrics, fingerprint is more acceptable and most countries use it as
an efficient methods of identification. This article provides a new
method to compare the fingerprint comparison by pattern recognition
and image processing techniques. To verify fingerprint, the shortest
distance method is used together with perceptronic multilayer neural
network functioning based on minutiae. This method is highly
accurate in the extraction of minutiae and it accelerates comparisons
due to elimination of false minutiae and is more reliable compared
with methods that merely use directional images.
Abstract: Impact is one of very important subjects which always have been considered in mechanical science. Nature of impact is such that which makes its control a hard task. Therefore it is required to present the transfer of impact to other vulnerable part of a structure, when it is necessary, one of the best method of absorbing energy of impact, is by using Thin-walled tubes these tubes collapses under impact and with absorption of energy, it prevents the damage to other parts.Purpose of recent study is to survey the deformation and energy absorption of tubes with different type of cross section (rectangular or square) and with similar volumes, height, mean cross section thickness, and material under loading with different speeds. Lateral loading of tubes are quasi-static type and beside as numerical analysis, also experimental experiences has been performed to evaluate the accuracy of the results. Results from the surveys is indicates that in a same conditions which mentioned above, samples with square cross section ,absorb more energy compare to rectangular cross section, and also by increscent in speed of loading, energy absorption would be more.
Abstract: Recently, there has been a considerable increase in the
number of procedures carried out under regional anesthesia.
However, percutaneous nephrolithotomy (PCNL) procedures are
usually performed under general anesthesia. The aim of this study
was to assess the safety and efficacy of PCNL under spinal anesthesia
in patients with renal calculi. We describe our 9 years experience of
performing PCNL under spinal anesthesia for 387 patients with large
stones of the upper urinary tract, with regard to the effectiveness and
side effects. All patients received spinal anesthetics (Lidocain 5%, or
Bupivacaine 0.75%) and underwent PCNL in prone position. The
success rate was 94.1%. The incidence of complications was 11.6%.
PCNL under spinal anesthesia is feasible, safe, and well-tolerated in
management of patients with renal stones.
Abstract: Abdominal aortic aneurysms rupture (AAAs) is one of the main causes of death in the world. This is a very complex phenomenon that usually occurs “without previous warning". Currently, criteria to assess the aneurysm rupture risk (peak diameter and growth rate) can not be considered as reliable indicators. In a first approach, the main geometric parameters of aneurysms have been linked into five biomechanical factors. These are combined to obtain a dimensionless rupture risk index, RI(t), which has been validated preliminarily with a clinical case and others from literature. This quantitative indicator is easy to understand, it allows estimating the aneurysms rupture risks and it is expected to be able to identify the one in aneurysm whose peak diameter is less than the threshold value. Based on initial results, a broader study has begun with twelve patients from the Clinic Hospital of Valladolid-Spain, which are submitted to periodic follow-up examinations.
Abstract: Mycotoxin (aflatoxins) contamination of peanuts is a
great concern for human health. A total of 72 samples of unripe,
roasted, and salty peanuts were collected randomly from Pothohar
plateau of Pakistan for the assessment of aflatoxin. Samples were
dried, ground and extracted by acetonitrile (84%). The filtered
extracts were cleaned up by MycoSep-226 and analyzed by high
performance liquid chromatography with flourescence detector.
Quantification limit of Aflatoxin was 1 μg/kg and 70% Recovery was
observed in spiked samples in the range 1–10 μg/kg. The screening
of mycotoxins indicated that aflatoxins were present in most of the
samples being detected in 82%, in concentrations from 14.25 μg/kg
to 98.80 μg/kg. Optimal conditions for mycotoxin production and
fungal growth are frequently found in the crop fields as well as in
store houses. Human exposure of such toxin can be controlled by
pointed out such awareness and implemented the regulations.
Abstract: The Internet telephony employs a new type of Internet communication on which a mutual communication is realized by establishing sessions. Session Initiation Protocol (SIP) is used to establish sessions between end-users. For unreliable transmission (UDP), SIP message should be retransmitted when it is lost. The retransmissions increase a load of the SIP signaling network, and sometimes lead to performance degradation when a network is overloaded. The paper proposes an overload control for a SIP signaling network to protect from a performance degradation. Introducing two thresholds in a queue of a SIP proxy server, the SIP proxy server detects a congestion. Once congestion is detected, a SIP signaling network restricts to make new calls. The proposed overload control is evaluated using the network simulator (ns-2). With simulation results, the paper shows the proposed overload control works well.
Abstract: We prove detailed analysis of a waveguide-based Schottky barrier photodetector (SBPD) where a thin silicide film is put on the top of a silicon-on-insulator (SOI) channel waveguide to absorb light propagating along the waveguide. Taking both the confinement factor of light absorption and the wall scanning induced gain of the photoexcited carriers into account, an optimized silicide thickness is extracted to maximize the effective gain, thereby the responsivity. For typical lengths of the thin silicide film (10-20 Ðçm), the optimized thickness is estimated to be in the range of 1-2 nm, and only about 50-80% light power is absorbed to reach the maximum responsivity. Resonant waveguide-based SBPDs are proposed, which consist of a microloop, microdisc, or microring waveguide structure to allow light multiply propagating along the circular Si waveguide beneath the thin silicide film. Simulation results suggest that such resonant waveguide-based SBPDs have much higher repsonsivity at the resonant wavelengths as compared to the straight waveguidebased detectors. Some experimental results about Si waveguide-based SBPD are also reported.
Abstract: In the present study, the effect of ferrous sulfate concentration and total solids on bioleaching of heavy metals from sewage sludge has been examined using indigenous iron-oxidizing microorganisms. The experiments on effects of ferrous sulfate concentrations on bioleaching were carried out using ferrous sulfate of different concentrations (5-20 g L-1) to optimize the concentration of ferrous sulfate for maximum bioleaching. A rapid change in the pH and ORP took place in first 2 days followed by a slow change till 16th day in all the sludge samples. A 10 g L-1 ferrous sulfate concentration was found to be sufficient in metal bioleaching in the following order: Zn: 69%>Cu: 52%>Cr: 46%>Ni: 45. Further, bioleaching using 10 g/L ferrous sulfate was found to be efficient up to 20 g L-1 sludge solids concentration. The results of the present study strongly indicate that using 10 g L-1 ferrous sulfate indigenous iron-oxidizing microorganisms can bring down pH to a value needed for significant metal solubilization.
Abstract: The procurement and cost management approach adopted for mechanical and electrical (M&E) services in Malaysian construction industry have been criticized for its inefficiency. The study examined early cost estimating practices adopted for mechanical and electrical services (M&E) in Malaysia so as to understand the level of compliance of the current techniques with best practices. The methodology adopted for the study is a review of bidding documents used on both completed and on – going building projects awarded between 2008 – 2010 under 9th Malaysian Plan. The analysis revealed that, M&E services cost cannot be reliably estimated at pre-contract stage; the bidding techniques adopted for M&E services failed to provide uniform basis for contractors to submit tender; detailed measurement of items were not made which could complicate post contract cost control and financial management. The paper concluded that, there is need to follow a structured approach in determining the pre-contract cost estimate for M&E services which will serve as a virile tool for post contract cost control.
Abstract: Fundamental sensor-motor couplings form the backbone
of most mobile robot control tasks, and often need to be implemented
fast, efficiently and nevertheless reliably. Machine learning
techniques are therefore often used to obtain the desired sensor-motor
competences.
In this paper we present an alternative to established machine
learning methods such as artificial neural networks, that is very fast,
easy to implement, and has the distinct advantage that it generates
transparent, analysable sensor-motor couplings: system identification
through nonlinear polynomial mapping.
This work, which is part of the RobotMODIC project at the
universities of Essex and Sheffield, aims to develop a theoretical understanding
of the interaction between the robot and its environment.
One of the purposes of this research is to enable the principled design
of robot control programs.
As a first step towards this aim we model the behaviour of the
robot, as this emerges from its interaction with the environment, with
the NARMAX modelling method (Nonlinear, Auto-Regressive, Moving
Average models with eXogenous inputs). This method produces
explicit polynomial functions that can be subsequently analysed using
established mathematical methods.
In this paper we demonstrate the fidelity of the obtained NARMAX
models in the challenging task of robot route learning; we present a
set of experiments in which a Magellan Pro mobile robot was taught
to follow four different routes, always using the same mechanism to
obtain the required control law.
Abstract: This paper proposes and analyses the wireless
telecommunication system with multiple antennas to the emission
and reception MIMO (multiple input multiple output) with space
diversity in a OFDM context. In particular it analyses the
performance of a DTT (Digital Terrestrial Television) broadcasting
system that includes MIMO-OFDM techniques. Different
propagation channel models and configurations are considered for
each diversity scheme. This study has been carried out in the context
of development of the next generation DVB-T/H and WRAN.
Abstract: Oxidative stress is considered to be the cause for onset
and the progression of type 2 diabetes mellitus (T2DM) and
complications including neuropathy. It is a deleterious process that
can be an important mediator of damage to cell structures: protein,
lipids and DNA. Data suggest that in patients with diabetes and
diabetic neuropathy DNA repair is impaired, which prevents effective
removal of lesions. Objective: The aim of our study was to evaluate
the association of the hOGG1 (326 Ser/Cys) and XRCC1 (194
Arg/Trp, 399 Arg/Gln) gene polymorphisms whose protein is
involved in the BER pathway with DNA repair efficiency in patients
with diabetes type 2 and diabetic neuropathy compared to the healthy
subjects. Genotypes were determined by PCR-RFLP analysis in 385
subjects, including 117 with type 2 diabetes, 56 with diabetic
neuropathy and 212 with normal glucose metabolism. The
polymorphisms studied include codon 326 of hOGG1 and 194, 399
of XRCC1 in the base excision repair (BER) genes. Comet assay was
carried out using peripheral blood lymphocytes from the patients and
controls. This test enabled the evaluation of DNA damage in cells
exposed to hydrogen peroxide alone and in the combination with the
endonuclease III (Nth). The results of the analysis of polymorphism
were statistically examination by calculating the odds ratio (OR) and
their 95% confidence intervals (95% CI) using the ¤ç2-tests. Our data
indicate that patients with diabetes mellitus type 2 (including those
with neuropathy) had higher frequencies of the XRCC1 399Arg/Gln
polymorphism in homozygote (GG) (OR: 1.85 [95% CI: 1.07-3.22],
P=0.3) and also increased frequency of 399Gln (G) allele (OR: 1.38
[95% CI: 1.03-1.83], P=0.3). No relation to other polymorphisms
with increased risk of diabetes or diabetic neuropathy. In T2DM
patients complicated by neuropathy, there was less efficient repair of
oxidative DNA damage induced by hydrogen peroxide in both the
presence and absence of the Nth enzyme. The results of our study
suggest that the XRCC1 399 Arg/Gln polymorphism is a significant
risk factor of T2DM in Polish population. Obtained data suggest a
decreased efficiency of DNA repair in cells from patients with
diabetes and neuropathy may be associated with oxidative stress.
Additionally, patients with neuropathy are characterized by even
greater sensitivity to oxidative damage than patients with diabetes,
which suggests participation of free radicals in the pathogenesis of
neuropathy.
Abstract: The use of new technologies such internet (e-mail, chat
rooms) and cell phones has steeply increased in recent years.
Especially among children and young people, use of technological
tools and equipments is widespread. Although many teachers and
administrators now recognize the problem of school bullying, few are
aware that students are being harassed through electronic
communication. Referred to as electronic bullying, cyber bullying, or
online social cruelty, this phenomenon includes bullying through email,
instant messaging, in a chat room, on a website, or through
digital messages or images sent to a cell phone. Cyber bullying is
defined as causing deliberate/intentional harm to others using internet
or other digital technologies. It has a quantitative research design nd
uses relational survey as its method. The participants consisted of
300 secondary school students in the city of Konya, Turkey. 195
(64.8%) participants were female and 105 (35.2%) were male. 39
(13%) students were at grade 1, 187 (62.1%) were at grade 2 and 74
(24.6%) were at grade 3. The “Cyber Bullying Question List"
developed by Ar─▒cak (2009) was given to students. Following
questions about demographics, a functional definition of cyber
bullying was provided. In order to specify students- human values,
“Human Values Scale (HVS)" developed by Dilmaç (2007) for
secondary school students was administered. The scale consists of 42
items in six dimensions. Data analysis was conducted by the primary
investigator of the study using SPSS 14.00 statistical analysis
software. Descriptive statistics were calculated for the analysis of
students- cyber bullying behaviour and simple regression analysis was
conducted in order to test whether each value in the scale could
explain cyber bullying behaviour.
Abstract: This paper describes a proposed support system which
enables applications designers to effectively create VR applications
using multiple haptic APIs. When the VR designers create
applications, it is often difficult to handle and understand many
parameters and functions that have to be set in the application program
using documentation manuals only. This complication may disrupt
creative imagination and result in inefficient coding. So, we proposed
the support application which improved the efficiency of VR
applications development and provided the interactive components of
confirmation of operations with haptic sense previously.
In this paper, we describe improvements of our former proposed
support application, which was applicable to multiple APIs and haptic
devices, and evaluate the new application by having participants
complete VR program. Results from a preliminary experiment suggest
that our application facilitates creation of VR applications.
Abstract: The risk sphere in business is fast changing and expanding. Almost anything has become a risk factor that will have potent, direct, and far reaching impacts on business. This paper examines the intensity of enterprise risk management (ERM) practices among the Malaysian public listed companies. The paper espouses a ERM framework comprising fourteen important implementation elements and processes. Results of the analysis indicate that the intensity of ERM implementation among the respondents is in the ‘good’ category of the semantic scale, which is deemed encouraging vis-à-vis the country’s regulatory regime.