Abstract: Single Minute Exchange of Dies (SMED) mainly focuses on recognition of internal and external activities. It is concerned particularly with transferring internal activities into external ones in as many numbers as possible, by also minimizing the internal ones. The validity of the method and procedures are verified by an application a Styrofoam manufacturing process where setup times are critical for time reduction. Significant time savings have been achieved with minimum investment. Further, the issues related with employer safety and ergonomics principles during die exchange are noted.
Abstract: Composite pins of rubber dust collected from tyre
retreading centres of trucks, cars and buses etc.and epoxy with
weight percentages of 10. 15, and 20 % of rubber (weight fractions of
9, 13 and 17 % respectively) have been prepared in house with the
help of a split wooden mould. The pins were tested in a pin-on-disc
wear monitor to determine the co-efficient of friction and weight
losses with varying speeds, loads and time. The wear volume and
wear rates have also been found out for all these three specimens.. It
is observed that all the specimens have exhibited very low coefficient
of friction and low wear rates under dry sliding condition. Out of the
above three samples tested, the specimen with 10 % rubber dust by
weight has shown lowest wear rates. However a peculiar result i.e
decreasing trend has been obtained with 20% reinforcement of rubber
in epoxy while rubbed against steel at varying speeds. This might
have occurred due to high surface finish of the disc and formation of
a thin transfer layer from the composite
Abstract: It is well known that the channel capacity of Multiple-
Input-Multiple-Output (MIMO) system increases as the number of
antenna pairs between transmitter and receiver increases but it suffers
from multiple expensive RF chains. To reduce the cost of RF chains,
Antenna Selection (AS) method can offer a good tradeoff between
expense and performance. In a transmitting AS system, Channel
State Information (CSI) feedback is necessarily required to choose
the best subset of antennas in which the effects of delays and errors
occurred in feedback channels are the most dominant factors
degrading the performance of the AS method. This paper presents the
concept of AS method using CSI from channel reciprocity instead of
feedback method. Reciprocity technique can easily archive CSI by
utilizing a reverse channel where the forward and reverse channels
are symmetrically considered in time, frequency and location. In this
work, the capacity performance of MIMO system when using AS
method at transmitter with reciprocity channels is investigated by
own developing Testbed. The obtained results show that reciprocity
technique offers capacity close to a system with a perfect CSI and
gains a higher capacity than a system without AS method from 0.9 to
2.2 bps/Hz at SNR 10 dB.
Abstract: The purpose of this paper is to assess the value of neural networks for classification of cancer and noncancer prostate cells. Gauss Markov Random Fields, Fourier entropy and wavelet average deviation features are calculated from 80 noncancer and 80 cancer prostate cell nuclei. For classification, artificial neural network techniques which are multilayer perceptron, radial basis function and learning vector quantization are used. Two methods are utilized for multilayer perceptron. First method has single hidden layer and between 3-15 nodes, second method has two hidden layer and each layer has between 3-15 nodes. Overall classification rate of 86.88% is achieved.
Abstract: Entrepreneurs are important for national labour markets and economies in that they contribute significantly to economic growth as well as provide the majority of jobs and create new ones. According to the Global Entrepreneurship Monitor’s “Report on Women and Entrepreneurship”, investment in women’s entrepreneurship is an important way to exponentially increase the impact of new venture creation finding ways to empower women’s participation and success in entrepreneurship are critical for more sustainable and successful economic development. Our results confirm that they are still differences between men and women entrepreneurs The reasons seems to be the lack of specific business skills, the less extensive social network, and the lack of identification patterns among women. Those differences can be explained by the fact that women still have fewer opportunities to make a career. If this is correct, we can predict an increasing proportion of women among entrepreneurs in the next years. Concerning the development of a favorable environment for developing and enhancing women entrepreneurship activities, our results show the insertion in a network and the role of a model doubtless represent elements determining in the choice to launch an entrepreneurship activity, as well as a precious resource for the success of her company.
Abstract: Preparation of size controlled nano-particles of silver catalyst on carbon substrate from e-waste has been investigated. Chemical route was developed by extraction of the metals available in nitric acid followed by treatment with hydrofluoric acid. Silver metal particles deposited with an average size 4-10 nm. A stabilizer concentration of 10- 40 g/l was used. The average size of the prepared silver decreased with increase of the anode current density. Size uniformity of the silver nano-particles was improved distinctly at higher current density no more than 20mA... Grain size increased with EK time whereby aggregation of particles was observed after 6 h of reaction.. The chemical method involves adsorption of silver nitrate on the carbon substrate. Adsorbed silver ions were directly reduced to metal particles using hydrazine hydrate. Another alternative method is by treatment with ammonia followed by heating the carbon loaded-silver hydroxide at 980°C. The product was characterized with the help of XRD, XRF, ICP, SEM and TEM techniques.
Abstract: The “conveyor belt" as a product represents a
complex high performance component with a wide range of different
applications. Further development of these highly complex
components demands an integration of new technologies and new
enhanced materials. In this context nanostructured fillers appear to
have a more promising effect on the performance of the conveyor
belt composite than conventional micro-scaled fillers.
Within the project “DotTrans" nanostructured fillers, for example
silicon dioxide, are used to optimize performance parameters of
conveyor belt systems. The objective of the project includes
operating parameters like energy consumption or friction
characteristics as well as adaptive parameters like cut or wear
resistance.
Abstract: The current work focuses on rephrasing the harmful
effects of mercury that is being released from a number of sources.
Most of the sources are from the industrial waste water. Different
techniques of mercury removal have been discussed and a brief
comparison among these has been made. The experimental work has
been conducted for two most widely used methods of mercury
removal and comparison in terms of their efficiency has been made.
Abstract: It has been defined that the “network is the system".
This implies providing levels of service, reliability, predictability and
availability that are commensurate with or better than those that
individual computers provide today. To provide this requires
integrated network management for interconnected networks of
heterogeneous devices covering both the local campus. In this paper
we are addressing a framework to effectively deal with this issue. It
consists of components and interactions between them which are
required to perform the service fault management. A real-world
scenario is used to derive the requirements which have been applied
to the component identification. An analysis of existing frameworks
and approaches with respect to their applicability to the framework is
also carried out.
Abstract: Creativity is often based on an unorthodox
recombination of knowledge; in fact: 80% of all innovations use
given knowledge and put it into a new combination. Cross-industry
innovations follow this way of thinking and bring together problems
and solution ideas from different industries. Therefore analogies and
search strategies have to be developed. Taking this path, the
questions where to search, what to search and how to search have to
be answered. Afterwards, the gathered information can be used
within a planned search process. Identified solution ideas have to be
assessed and analyzed in detail for the success promising adaption
planning.
Abstract: Face and facial expressions play essential roles in
interpersonal communication. Most of the current works on the facial
expression recognition attempt to recognize a small set of the
prototypic expressions such as happy, surprise, anger, sad, disgust
and fear. However the most of the human emotions are
communicated by changes in one or two of discrete features. In this
paper, we develop a facial expressions synthesis system, based on the
facial characteristic points (FCP's) tracking in the frontal image
sequences. Selected FCP's are automatically tracked using a crosscorrelation
based optical flow. The proposed synthesis system uses a
simple deformable facial features model with a few set of control
points that can be tracked in original facial image sequences.
Abstract: In this work, a special case of the image superresolution
problem where the only type of motion is global
translational motion and the blurs are shift-invariant is investigated.
The necessary conditions for exact reconstruction of the original
image by using finite impulse-response reconstruction filters are
developed. Given that the conditions are satisfied, a method for exact
super-resolution is presented and some simulation results are shown.
Abstract: Oilsands bitumen is an extremely important source of
energy for North America. However, due to the presence of large
molecules such as asphaltenes, the density and viscosity of the
bitumen recovered from these sands are much higher than those of
conventional crude oil. As a result the extracted bitumen has to be
diluted with expensive solvents, or thermochemically upgraded in
large, capital-intensive conventional upgrading facilities prior to
pipeline transport. This study demonstrates that globally abundant
natural zeolites such as clinoptilolite from Saint Clouds, New Mexico
and Ca-chabazite from Bowie, Arizona can be used as very effective
reagents for cracking and visbreaking of oilsands bitumen. Natural
zeolite cracked oilsands bitumen products are highly recoverable (up
to ~ 83%) using light hydrocarbons such as pentane, which indicates
substantial conversion of heavier fractions to lighter components.
The resultant liquid products are much less viscous, and have lighter
product distribution compared to those produced from pure thermal
treatment. These natural minerals impart similar effect on industrially
extracted Athabasca bitumen.
Abstract: Ever increasing capacities of contemporary storage devices
inspire the vision to accumulate (personal) information without
the need of deleting old data over a long time-span. Hence the target
of SemanticLIFE project is to create a Personal Information Management
system for a human lifetime data. One of the most important
characteristics of the system is its dedication to retrieve information
in a very efficient way. By adopting user demands regarding the
reduction of ambiguities, our approach aims at a user-oriented and
yet powerful enough system with a satisfactory query performance.
We introduce the query system of SemanticLIFE, the Virtual Query
System, which uses emerging Semantic Web technologies to fulfill
users- requirements.
Abstract: In this paper, the effect of receive and/or transmit
antenna spacing on the performance (BER vs. SNR) of multipleantenna
systems is determined by using an RCS (Radar Cross
Section) channel model. In this physical model, the scatterers
existing in the propagation environment are modeled by their RCS so
that the correlation of the receive signal complex amplitudes, i.e.,
both magnitude and phase, can be estimated. The proposed RCS
channel model is then compared with classical models.
Abstract: In IETF RFC 2002, Mobile-IP was developed to
enable Laptobs to maintain Internet connectivity while moving
between subnets. However, the packet loss that comes from
switching subnets arises because network connectivity is lost while
the mobile host registers with the foreign agent and this encounters
large end-to-end packet delays. The criterion to initiate a simple and
fast full-duplex connection between the home agent and foreign
agent, to reduce the roaming duration, is a very important issue to be
considered by a work in this paper. State-transition Petri-Nets of the
modeling scenario-based CIA: communication inter-agents procedure
as an extension to the basic Mobile-IP registration process was
designed and manipulated to describe the system in discrete events.
The heuristic of configuration file during practical Setup session for
registration parameters, on Cisco platform Router-1760 using IOS
12.3 (15)T and TFTP server S/W is created. Finally, stand-alone
performance simulations from Simulink Matlab, within each subnet
and also between subnets, are illustrated for reporting better end-toend
packet delays. Results verified the effectiveness of our Mathcad
analytical manipulation and experimental implementation. It showed
lower values of end-to-end packet delay for Mobile-IP using CIA
procedure-based early registration. Furthermore, it reported packets
flow between subnets to improve losses between subnets.
Abstract: Artificial Intelligence based gaming is an interesting topic in the state-of-art technology. This paper presents an automation of a tradition Omani game, called Al-Hawalees. Its related issues are resolved and implemented using artificial intelligence approach. An AI approach called mini-max procedure is incorporated to make a diverse budges of the on-line gaming. If number of moves increase, time complexity will be increased in terms of propositionally. In order to tackle the time and space complexities, we have employed a back propagation neural network (BPNN) to train in off-line to make a decision for resources required to fulfill the automation of the game. We have utilized Leverberg- Marquardt training in order to get the rapid response during the gaming. A set of optimal moves is determined by the on-line back propagation training fashioned with alpha-beta pruning. The results and analyses reveal that the proposed scheme will be easily incorporated in the on-line scenario with one player against the system.
Abstract: The presented work is motivated by a French law
regarding nuclear waste management. A new conceptual Accelerator
Driven System (ADS) designed for the Minor Actinides (MA)
transmutation has been assessed by numerical simulation. The
MUltiple Spallation Target (MUST) ADS combines high thermal power (up to 1.4 GWth) and high specific power. A 30 mA and 1
GeV proton beam is divided into three secondary beams transmitted on three liquid lead-bismuth spallation targets. Neutron and thermalhydraulic
simulations have been performed with the code MURE, based on the Monte-Carlo transport code MCNPX. A methodology has been developed to define characteristic of the MUST ADS concept according to a specific transmutation scenario. The reference
scenario is based on a MA flux (neptunium, americium and curium)
providing from European Fast Reactor (EPR) and a plutonium multireprocessing
strategy is accounted for. The MUST ADS reference
concept is a sodium cooled fast reactor. The MA fuel at equilibrium is mixed with MgO inert matrix to limit the core reactivity and
improve the fuel thermal conductivity. The fuel is irradiated over five
years. Five years of cooling and two years for the fuel fabrication are
taken into account. The MUST ADS reference concept burns about 50% of the initial MA inventory during a complete cycle. In term of
mass, up to 570 kg/year are transmuted in one concept. The methodology to design the MUST ADS and to calculate fuel
composition at equilibrium is precisely described in the paper. A detailed fuel evolution analysis is performed and the reference scenario is compared to a scenario where only americium transmutation is performed.
Abstract: Springback is a significant problem in the sheet metal
forming process. When the tools are released after the stage of
forming, the product springs out, because of the action of the internal
stresses. In many cases the deviation of form is too large and the
compensation of the springback is necessary. The precise prediction
of the springback of product is increasingly significant for the design
of the tools and for compensation because of the higher ratio of the
yield stress to the elastic modulus.
The main object in this paper was to study the effect of the
anisotropy on the springback for three directions of rolling: 0°, 45°
and 90°. At the same time, we highlighted the influence of three
different metallic materials: Aluminum, Steel and Galvanized steel.
The original of our purpose consist on tests which are ensured by
adapting a U-type stretching-bending device on a tensile testing
machine, where we studied and quantified the variation of the
springback according to the direction of rolling. We also showed the
role of lubrication in the reduction of the springback.
Moreover, in this work, we have studied important characteristics
in deep drawing process which is a springback. We have presented
defaults that are showed in this process and many parameters
influenced a springback.
Finally, our results works lead us to understand the influence of
grains orientation with different metallic materials on the springback
and drawing some conclusions how to concept deep drawing tools. In
addition, the conducted work represents a fundamental contribution
in the discussion the industry application.
Abstract: At present, it is very common to find renewable
energy resources, especially wind power, connected to distribution
systems. The impact of this wind power on voltage distribution levels
has been addressed in the literature. The majority of this works deals
with the determination of the maximum active and reactive power
that is possible to be connected on a system load bus, until the
voltage at that bus reaches the voltage collapse point. It is done by the
traditional methods of PV curves reported in many references.
Theoretical expression of maximum power limited by voltage
stability transfer through a grid is formulated using an exact
representation of distribution line with ABCD parameters. The
expression is used to plot PV curves at various power factors of a
radial system. Limited values of reactive power can be obtained. This
paper presents a method to study the relationship between the active
power and voltage (PV) at the load bus to identify the voltage
stability limit. It is a foundation to build a permitted working
operation region in complying with the voltage stability limit at the
point of common coupling (PCC) connected wind farm.