Abstract: In present work the problem of the ITER fusion
plasma neutron source parameter reconstruction using only the
Vertical Neutron Camera data was solved. The possibility of neutron
source parameter reconstruction was estimated by the numerical
simulations and the analysis of adequateness of mathematic model
was performed. The neutron source was specified in a parametric
form. The numerical analysis of solution stability with respect to data
distortion was done. The influence of the data errors on the
reconstructed parameters is shown:
• is reconstructed with errors less than 4% at all examined values
of δ (until 60%);
• is determined with errors less than 10% when δ do not overcome
5%;
• is reconstructed with relative error more than 10 %;
• integral intensity of the neutron source is determined with error
10% while δ error is less than 15%;
where -error of signal measurements, (R0,Z0), the plasma center
position,- /parameter of neutron source profile.
Abstract: This paper characterizes the effects of artificial short
term aging in the laboratory on the rheological properties of virgin
80/100 penetration grade asphalt binder. After several years in
service, asphalt mixture started to deteriorate due to aging. Aging is a
complex physico-chemical phenomenon that influences asphalt
binder rheological properties causing a deterioration in asphalt
mixture performance. To ascertain asphalt binder aging effects, the
virgin, artificially aged and extracted asphalt binder were tested via
the Rolling Thin film Oven (RTFO), Dynamic Shear Rheometer
(DSR) and Rotational Viscometer (RV). A comparative study
between laboratory and field aging conditions were also carried out.
The results showed that the specimens conditioned for 85 minutes
inside the RTFO was insufficient to simulate the actual short term
aging caused that took place in the field under Malaysian field
conditions
Abstract: Earlier studies in kinship networks have primarily
focused on observing the social relationships existing between family
relatives. In this study, we pre-identified hubs in the network to
investigate if they could play a catalyst role in the transfer of physical
information. We conducted a case study of a ceremony performed in
one of the families of a small Hindu community – the Uttar Rarhi
Kayasthas. Individuals (n = 168) who resided in 11 geographically
dispersed regions were contacted through our hub-based
representation. We found that using this representation, over 98% of
the individuals were successfully contacted within the stipulated
period. The network also demonstrated a small-world property, with
an average geodesic distance of 3.56.
Abstract: In the past decade, the development of microstrip
sensor application has evolved tremendously. Although cut and trial
method was adopted to develop microstrip sensing applications in the
past, Computer-Aided-Design (CAD) is a more effective as it ensures
less time is consumed and cost saving is achieved in developing
microstrip sensing applications. Therefore microstrip sensing
applications has gained popularity as an effective tool adopted in
continuous sensing of moisture content particularly in products that is
administered mainly by liquid content. In this research, the Cole-Cole
representation of reactive relaxation is applied to assess the
performance of the microstrip sensor devices. The microstrip sensor
application is an effective tool suitable for sensing the moisture
content of dielectric material. Analogous to dielectric relaxation
consideration of Cole-Cole diagrams as applied to dielectric
materials, a “reactive relaxation concept” concept is introduced to
represent the frequency-dependent and moisture content
characteristics of microstrip sensor devices.
Abstract: This research aimed to study the competency of health
and wellness hotels and resorts in developing use the local natural
resources and wisdom to conform to the national health and wellness
tourism (HWT) strategy by comparing two independent samples,
from Aumpur Muang, Ranong province and Aumpur Muang,
Chiangmai province. And also study in the suggestive direct path to
lead the organization to the sustainable successful.
This research was conduct by using mix methodology; both
quantitative and qualitative data were used. The data of competency
of health and wellness hotels and resorts (HWHR) in developing use
the local natural resources for HWT promoting were collected via
300 set of questionnaires, from 6 hotels and resorts in 2 areas, 3
places from Aumpur Muang, Ranong province and another 3 from
Aumpur Muang, Chiangmai province.
Thestudy of HWHR’s competency in developing use the local
natural resources and wisdom to conform to the national HWT
strategycan be divided into fourmain areas, food and beverages
service, tourism activity, environmental service, and value adding.
The total competency of the Chiangmai sample is importantly
scoredp. value 0.01 higher than the Ranong one while the area of
safety, Chiangmai’s competency is importantly scored 0.05 higher
than the Ranong’scompetency. Others were rated not differently.
Since Chiangmai perform better, then it can be a role model in
developing HTHR or HWT destination.
From the part of qualitative research, content analysis of business
contents and its environments were analyzed. The four stages of
strategic development and plans, from the smallest scale to the largest
scale such a national base were discussed. The HWT: Evolution
model and strategy for lodging Business were suggested. All those
stages must work harmoniously together. The distinctive result
illustrates the need of human resource development as the key point
to create the identity of Thainess on Health and wellness service
providing. This will add-on the value of services and differentiates
ourselves from other competitors. The creative of Thailand’s health
and wellness brand possibly increase loyalty customers which agreed
to be a path of sustainable development.
Abstract: Grid computing is a high performance computing
environment to solve larger scale computational applications. Grid
computing contains resource management, job scheduling, security
problems, information management and so on. Job scheduling is a
fundamental and important issue in achieving high performance in
grid computing systems. However, it is a big challenge to design an
efficient scheduler and its implementation. In Grid Computing, there
is a need of further improvement in Job Scheduling algorithm to
schedule the light-weight or small jobs into a coarse-grained or
group of jobs, which will reduce the communication time,
processing time and enhance resource utilization. This Grouping
strategy considers the processing power, memory-size and
bandwidth requirements of each job to realize the real grid system.
The experimental results demonstrate that the proposed scheduling
algorithm efficiently reduces the processing time of jobs in
comparison to others.
Abstract: The selective wet-etching of amorphous and
crystalline region of Sb20Se80 thin films was carried out using organic
based solution e.g. amines. We report the development of an in situ
real-time method to study the wet chemical etching process of thin
films. Characterization of the structure and surface of films studied
by X-ray diffraction, SEM and EBSD methods has been done and
potential application suggested.
Abstract: In switch mode power inverters, small sized inverters
can be obtained by increasing the switching frequency. Switching
frequency increment causes high driver losses. Also, high dt
di
and
dt
dv
produced by the switching action creates high Electromagnetic
Interference (EMI) and Radio Frequency Interference (RFI). In this
paper, a series half bridge series resonant inverter circuit is simulated
and evaluated practically to demonstrate the turn-on and turn-off
conditions during zero or close to zero voltage switching. Also, the
reverse recovery current effects of the body diode of the MOSFETs
were investigated by operating above and below resonant frequency.
Abstract: A theory for optimal filtering of infinite sets of random
signals is presented. There are several new distinctive features of the
proposed approach. First, a single optimal filter for processing any
signal from a given infinite signal set is provided. Second, the filter is
presented in the special form of a sum with p terms where each term
is represented as a combination of three operations. Each operation
is a special stage of the filtering aimed at facilitating the associated
numerical work. Third, an iterative scheme is implemented into the
filter structure to provide an improvement in the filter performance at
each step of the scheme. The final step of the scheme concerns signal
compression and decompression. This step is based on the solution of
a new rank-constrained matrix approximation problem. The solution
to the matrix problem is described in this paper. A rigorous error
analysis is given for the new filter.
Abstract: A 2.4GHz (RF) down conversion Gilbert Cell mixer,
implemented in a 0.18-μm CMOS technology with a 1.8V supply, is
presented. Current bleeding (charge injection) technique has been
used to increase the conversion gain and the linearity of the mixer.
The proposed mixer provides 10.75 dB conversion gain ( C G ) with
14.3mw total power consumption. The IIP3 and 1-dB compression
point of the mixer are 8dbm and -4.6dbm respectively, at 300 MHz
IF frequencies. Comparing the current design against the
conventional mixer design, demonstrates better performance in the
conversion gain, linearity, noise figure and port-to-port isolation.
Abstract: In a previously developed fast vortex method, the
diffusion of the vortex sheet induced at the solid wall by the no-slip
boundary conditions was modeled according to the approximation
solution of Koumoutsakos and converted into discrete blobs in the
vicinity of the wall. This scheme had been successfully applied to a
simulation of the flow induced with an impulsively initiated circular
cylinder. In this work, further modifications on this vortex method are
attempted, including replacing the approximation solution by the
boundary-element-method solution, incorporating a new algorithm for
handling the over-weak vortex blobs, and diffusing the vortex sheet
circulation in a new way suitable for high-curvature solid bodies. The
accuracy is thus largely improved. The predictions of lift and drag
coefficients for a uniform flow past a NASA airfoil agree well with the
existing literature.
Abstract: Synchronization is a difficult problem in CDMA
satellite communications. Due to the influence of additive noise and
fading in the mobile channel, it is not easy to keep up with the
attenuation and offset. This paper considers a recently proposed
approach to solve the problem of synchronization chaotic Chen
system in CDMA satellite communication in the presence of constant
attenuation and offset. An analytic algorithm that provides closed
form channel and carrier offset estimates is presented. The principle
of this approach is based on adding a compensation block before the
receiver to compensate the distortion of the imperfect channel by
using genetic algorithm.
The resultants presented, show that the receiver is able to recover
rapidly the synchronization with the transmitter.
Abstract: One of the main image representations in Mathematical Morphology is the 3D Shape Decomposition Representation, useful for Image Compression and Representation,and Pattern Recognition. The 3D Morphological Shape Decomposition representation can be generalized a number of times,to extend the scope of its algebraic characteristics as much as possible. With these generalizations, the Morphological Shape Decomposition 's role to serve as an efficient image decomposition tool is extended to grayscale images.This work follows the above line, and further develops it. Anew evolutionary branch is added to the 3D Morphological Shape Decomposition's development, by the introduction of a 3D Multi Structuring Element Morphological Shape Decomposition, which permits 3D Morphological Shape Decomposition of 3D binary images (grayscale images) into "multiparameter" families of elements. At the beginning, 3D Morphological Shape Decomposition representations are based only on "1 parameter" families of elements for image decomposition.This paper addresses the gray scale inter frame interpolation by means of mathematical morphology. The new interframe interpolation method is based on generalized morphological 3D Shape Decomposition. This article will present the theoretical background of the morphological interframe interpolation, deduce the new representation and show some application examples.Computer simulations could illustrate results.
Abstract: A real-time tracking system was built to track performers on an interactive stage. Using an ordinary, up to date, desktop workstation, the performers- silhouette was segmented from the background and parameterized by calculating the normalized central image moments. In the stage system, the silhouette moments were then sent to a parallel workstation, which used them to generate corresponding 3D virtual geometry and projected the generated graphic back onto the stage.
Abstract: The paper presents an on-line recognition machine
(RM) for continuous/isolated, dynamic and static gestures that arise
in Flight Deck Officer (FDO) training. RM is based on generic pattern
recognition framework. Gestures are represented as templates using
summary statistics. The proposed recognition algorithm exploits temporal
and spatial characteristics of gestures via dynamic programming
and Markovian process. The algorithm predicts corresponding index
of incremental input data in the templates in an on-line mode.
Accumulated consistency in the sequence of prediction provides a
similarity measurement (Score) between input data and the templates.
The algorithm provides an intuitive mechanism for automatic detection
of start/end frames of continuous gestures. In the present paper,
we consider isolated gestures. The performance of RM is evaluated
using four datasets - artificial (W TTest), hand motion (Yang) and
FDO (tracker, vision-based ). RM achieves comparable results which
are in agreement with other on-line and off-line algorithms such as
hidden Markov model (HMM) and dynamic time warping (DTW).
The proposed algorithm has the additional advantage of providing
timely feedback for training purposes.
Abstract: The main aim of the presented experiments is to
improve behaviour of sandwich structures under dynamic loading,
such as crash or explosion. Several cellular materials are widely used
as core of the sandwich structures and their properties influence
the response of the entire element under impact load. To optimize
their performance requires the characterisation of the core material
behaviour at high strain rates and identification of the underlying
mechanism. This work presents the study of high strain-rate
characteristics of a specific porous lightweight blast energy absorbing
foam using a Split Hopkinson Pressure Bar (SHPB) technique
adapted to perform tests on low strength materials. Two different
velocities, 15 and 30 m.s-1 were used to determine the strain
sensitivity of the material. Foams were designed using two types of
porous lightweight spherical raw materials with diameters of 30-
100 *m, combined with polymer matrix. Cylindrical specimens with
diameter of 15 mm and length of 7 mm were prepared and loaded
using a Split Hopkinson Pressure Bar apparatus to assess the relation
between the composition of the material and its shock wave
attenuation capacity.
Abstract: Film, as an art form playing a vital role and is a powerful tool in documenting, influencing and shaping the society. Films are the collective creation of a large number of separate individuals, each contributing with creative input, unique talents, and technical expertise to the project. Recently, the Malaysian Independent (or “Indie") filmmakers have made their presence felt by winning awards at various international film festivals. Working in the digital video (DV) format, a number of independent filmmakers really hit their stride with a range of remarkably strong titles and international recognition has been quick in coming and their works are now regularly in exhibition or in competition, winning many top prizes at prestigious festivals around the world. The interaction factors among crewmembers are emphasized as imperative for group success. An in-depth interview is conducted to analyze the social interactions and exchanges between filmmakers through Social Exchanges Theory (SET). Certainly the new millennium that was marked as the digital technology revolution has changed the face of filmmaking in Malaysia. There is a clear need to study the Malaysian independent cinema especially from the perspective of understanding what causes the independent filmmakers to work so well given all of the difficulties and constraints.
Abstract: Genetic Zone Routing Protocol (GZRP) is a new
hybrid routing protocol for MANETs which is an extension of ZRP
by using Genetic Algorithm (GA). GZRP uses GA on IERP and BRP
parts of ZRP to provide a limited set of alternative routes to the
destination in order to load balance the network and robustness
during node/link failure during the route discovery process. GZRP is
studied for its performance compared to ZRP in many folds like
scalability for packet delivery and proved with improved results. This
paper presents the results of the effect of load balancing on GZRP.
The results show that GZRP outperforms ZRP while balancing the
load.
Abstract: Future astronomical projects on large space x-ray
imaging telescopes require novel substrates and technologies for the
construction of their reflecting mirrors. The mirrors must be
lightweight and precisely shaped to achieve large collecting area with
high angular resolution. The new materials and technologies must be
cost-effective. Currently, the most promising materials are glass or
silicon foils. We focused on precise shaping these foils by thermal
forming process. We studied free and forced slumping in the
temperature region of hot plastic deformation and compared the
shapes obtained by the different slumping processes. We measured
the shapes and the surface quality of the foils. In the experiments, we
varied both heat-treatment temperature and time following our
experiment design. The obtained data and relations we can use for
modeling and optimizing the thermal forming procedure.
Abstract: This paper presents the approximate analytical solution of a Zakharov-Kuznetsov ZK(m, n, k) equation with the help of the differential transform method (DTM). The DTM method is a powerful and efficient technique for finding solutions of nonlinear equations without the need of a linearization process. In this approach the solution is found in the form of a rapidly convergent series with easily computed components. The two special cases, ZK(2,2,2) and ZK(3,3,3), are chosen to illustrate the concrete scheme of the DTM method in ZK(m, n, k) equations. The results demonstrate reliability and efficiency of the proposed method.