Abstract: The detection of environmental gases, 12CO2, 13CO2,
and CH4, using near-infrared semiconductor lasers with a short
laser path length is studied by means of wavelength-modulation
spectroscopy. The developed system is compact and has high
sensitivity enough to detect the absorption peaks of isotopic 13CO2
of a 3-% CO2 gas at 2 μm with a path length of 2.4 m, where
its peak size is two orders of magnitude smaller than that of the
ordinary 12CO2 peaks. In addition, the detection of 12CO2 peaks of
a 385-ppm (0.0385-%) CO2 gas in the air is made at 2 μm with a
path length of 1.4 m. Furthermore, in pursuing the detection of an
ancient environmental CH4 gas confined to a bubble in ice at the
polar regions, measurements of the absorption spectrum for a trace
gas of CH4 in a small area are attempted. For a 100-% CH4 gas
trapped in a ∼ 1 mm3 glass container, the absorption peaks of CH4
are obtained at 1.65 μm with a path length of 3 mm, and also the
gas pressure is extrapolated from the measured data.
Abstract: Recent advances in wireless networking technologies
introduce several energy aware routing protocols in sensor networks.
Such protocols aim to extend the lifetime of network by reducing the
energy consumption of nodes. Many researchers are looking for
certain challenges that are predominant in the grounds of energy
consumption. One such protocol that addresses this energy
consumption issue is ‘Cluster based hierarchical routing protocol’. In
this paper, we intend to discuss some of the major hierarchical
routing protocols adhering towards sensor networks. Furthermore, we
examine and compare several aspects and characteristics of few
widely explored hierarchical clustering protocols, and its operations
in wireless sensor networks (WSN). This paper also presents a
discussion on the future research topics and the challenges of
hierarchical clustering in WSNs.
Abstract: This research focuses on the optimization of glazed
surfaces and the assessment of possible solar gains in industrial
buildings. Existing window rating methods for single windows were
evaluated and a new method for a simple analysis of energy gains and
losses by single windows was introduced. Furthermore extensive
transient building simulations were carried out to appraise the
performance of low cost polycarbonate multi-cell sheets in
interaction with typical buildings for industrial applications. Mainly
energy saving potential was determined by optimizing the orientation
and area of such glazing systems in dependency on their thermal
qualities. Moreover the impact on critical aspects such as summer
overheating and daylight illumination was considered to ensure the
user comfort and avoid additional energy demand for lighting or
cooling. Hereby the simulated heating demand could be reduced by
up to 1/3 compared to traditional architecture of industrial halls using
mainly skylights.
Abstract: This paper attempts to evaluate the effect of fire
damage on concrete by using nonlinear resonance vibration method,
one of the nonlinear nondestructive method. Concrete exhibits not
only nonlinear stress-strain relation but also hysteresis and discrete
memory effect which are contained in consolidated materials.
Hysteretic materials typically show the linear resonance frequency
shift. Also, the shift of resonance frequency is changed according to
the degree of micro damage. The degree of the shift can be obtained
through nonlinear resonance vibration method. Five exposure
scenarios were considered in order to make different internal micro
damage. Also, the effect of post-fire-curing on fire-damaged concrete
was taken into account to conform the change in internal damage.
Hysteretic nonlinearity parameter was obtained by amplitudedependent
resonance frequency shift after specific curing periods. In
addition, splitting tensile strength was measured on each sample to
characterize the variation of residual strength. Then, a correlation
between the hysteretic nonlinearity parameter and residual strength
was proposed from each test result.
Abstract: Calcium phosphate coating (CaP) has been employed
for protein delivery, but the typical direct protein adsorption on the
coating led to low incorporation content and fast release of the
protein from the coating. By using bovine serum albumin (BSA) as a
model protein, rapid biomimetic co-precipitation between calcium
phosphate and BSA was employed to control the distribution of BSA
within calcium phosphate coating during biomimetic formation on
titanium surface for only 6 h at 50oC in an accelerated calcium
phosphate solution. As a result, the amount of BSA incorporation and
release duration could be increased by using a rapid biomimetic coprecipitation
technique. Up to 43 fold increases in the BSA
incorporation content and the increase from 6 h to more than 360 h in
release duration compared to typical direct adsorption technique were
observed depending on the initial BSA concentration used during coprecipitation
(1, 10 and 100 μg.ml-1). From x-ray diffraction and
Fourier transform infrared spectroscopy studies, the coating
composition was not altered with the incorporation of BSA by this
rapid biomimetic co-precipitation and mainly comprised octacalcium
phosphate and hydroxyapatite. However, the microstructure of
calcium phosphate crystals changed from straight, plate-like units to
curved, plate-like units with increasing BSA content.
Abstract: The success of any retail business is predisposed by its
swift response and its knack in understanding the constraints and the
requirements of customers. In this paper a conceptual design model
of an automated customer-friendly supermarket has been proposed.
In this model a 10-sided, space benefited, regular polygon shaped
gravity shelves have been designed for goods storage and effective
customer-specific algorithms have been built-in for quick automatic
delivery of the randomly listed goods. The algorithm is developed
with two main objectives, viz., delivery time and priority. For
meeting these objectives the randomly listed items are reorganized
according to the critical-path of the robotic arm specific to the
identified shop and its layout and the items are categorized according
to the demand, shape, size, similarity and nature of the product for an
efficient pick-up, packing and delivery process. We conjectured that
the proposed automated supermarket model reduces business
operating costs with much customer satisfaction warranting a winwin
situation.
Abstract: For a given a simple connected graph, we present
some new bounds via a new approach for a special topological index
given by the sum of the real number power of the non-zero
normalized Laplacian eigenvalues. To use this approach presents an
advantage not only to derive old and new bounds on this topic but
also gives an idea how some previous results in similar area can be
developed.
Abstract: No matter how much perfect we become in our
practical skills regarding the implementation of learned ideas, the
need of technical writing capability cannot be neglected being a
professional. Technical writing is a way of communicating the ideas
in written which otherwise need to be presented orally. Technical
writing skills have always been the need of the time, as they are
required for internal as well as external official communication in
both formal and informal manner. Moreover, they are the best way to
capture the attention of your customers by presenting information in
effective manner. This paper aims to analyze the importance of
technical writing skills in professional industries of Pakistan by
conducting a survey. Survey results presented in this paper clearly
depicts the importance of formal and informal written communication
media used in different professional industries in Pakistan. Analysis
and discussion of the extent to which the alternative ways of
communication besides technical writing have got importance in
Pakistan is also an important aspect of this survey.
Abstract: Pollution of the Klip River has caused
microorganisms inhabiting it to develop protective survival
mechanisms. This study isolated and characterized the heavy metal
resistant bacteria in the Klip River. Water and sediment samples were
collected from six sites along the course of the river. The pH,
turbidity, salinity, temperature and dissolved oxygen were measured
in-situ. The concentrations of six heavy metals (Cd, Cu, Fe, Ni, Pb
and Zn) of the water samples were determined by atomic absorption
spectroscopy. Biochemical and antibiotic profiles of the isolates were
assessed using the API 20E® and Kirby Bauer Method. Growth
studies were carried out using spectrophotometric methods. The
isolates were identified using 16SrDNA sequencing. The uppermost
part of the Klip River with the lowest pH had the highest levels of
heavy metals. Turbidity, salinity and specific conductivity increased
measurably at Site 4 (Henley on Klip Weir). MIC tests showed that
16 isolates exhibited high iron and lead resistance. Antibiotic
susceptibility tests revealed that the isolates exhibited multitolerances
to drugs such as Tetracycline, Ampicillin, and
Amoxicillin.
Abstract: Malathion (ML) is a well known pesticide commonly
used in many agricultural and non-agricultural processes. Its toxicity
has been attributed primarily to the accumulation of acetylcholine
(Ach) at nerve junctions, due to the inhibition of acetylcholinesterase
(AChE). The aim of the current research was to study the protective
effect of the melissa plant extract against reproductive impairment
induced by malathion in 32 male albino rats, and the biological
experiment was divided into four groups (8 in each) that given
malathion (27 mg/kg; 1/50 of the LD50 for an oral dose) and/or
Melissa officinalis (MO) extract (200mg/kg/day) by gavages
technique. The sperm counts, sperm motility, sperm morphology,
FSH, LH, and testosterone levels had been determined in testes
homogenate at the end of the experiment. It is worthy to report that,
rats treated with melissa extract did not show a significant difference
when compared with the control group, while rats given malathion
alone had significantly lower sperm count, sperm motility, and
significantly higher abnormal sperm numbers, than the untreated
control rats as well as having significantly lower serum FSH, LH, and
testosterone levels compared with the control group. Administrations
of melissa extract restore all mentioned histological parameters
towards the control group and the melissa extract had a strong
positive protective effect against malathion toxicity. Results the of
biological parameters were confirmed by the histological
examination of rat testes and indicated that, both control and melissa
groups showing normal seminiferous tubules, while malathion group
testicular tissues had necrosis, edema in the seminiferous tubules and
degeneration of spermatogonial cells lining the seminiferous tubules
with incomplete spermatogenesis. The use of melissa against
malathion improved the histological picture and showing normal
seminiferous tubules with complete spermatogenesis and almost there
was no histopathological changes could be noted.
Abstract: Recent perceived climate variability raises concerns
with unprecedented hydrological phenomena and extremes.
Distribution and circulation of the waters of the Earth become
increasingly difficult to determine because of additional uncertainty
related to anthropogenic emissions. The world wide observed
changes in the large-scale hydrological cycle have been related to an
increase in the observed temperature over several decades. Although
the effect of change in climate on hydrology provides a general
picture of possible hydrological global change, new tools and
frameworks for modelling hydrological series with nonstationary
characteristics at finer scales, are required for assessing climate
change impacts. Of the downscaling techniques, dynamic
downscaling is usually based on the use of Regional Climate Models
(RCMs), which generate finer resolution output based on atmospheric
physics over a region using General Circulation Model (GCM) fields
as boundary conditions. However, RCMs are not expected to capture
the observed spatial precipitation extremes at a fine cell scale or at a
basin scale. Statistical downscaling derives a statistical or empirical
relationship between the variables simulated by the GCMs, called
predictors, and station-scale hydrologic variables, called predictands.
The main focus of the paper is on the need for using statistical
downscaling techniques for projection of local hydrometeorological
variables under climate change scenarios. The projections can be then
served as a means of input source to various hydrologic models to
obtain streamflow, evapotranspiration, soil moisture and other
hydrological variables of interest.
Abstract: Three dimensional non-Interlaced carbon fibre
reinforced silicon carbide (3-D-Cf/SiC) composites with pyrocarbon
interphase were fabricated using isothermal chemical vapor
infiltration (ICVI) combined with polymer impregnation pyrolysis
(PIP) process. Polysilazane (PSZ) is used as a preceramic polymer to
obtain silicon carbide matrix. Thermo gravimetric analysis (TGA),
Infrared spectroscopic analysis (IR) and X-ray diffraction (XRD)
analysis were carried out on PSZ pyrolysed at different temperatures
to understand the pyrolysis and obtaining the optimum pyrolysing
condition to yield β-SiC phase. The density of the composites was
1.94 g cm-3 after the 3-D carbon preform was SiC infiltrated for 280 h
with one intermediate polysilazane pre-ceramic PIP process.
Mechanical properties of the composite materials were investigated
under tensile, flexural, shear and impact loading. The values of
tensile strength were 200 MPa at room temperature (RT) and 195
MPa at 500°C in air. The average RT flexural strength was 243 MPa.
The lower flexural strength of these composites is because of the
porosity. The fracture toughness obtained from single edge notched
beam (SENB) technique was 39 MPa.m1/2. The work of fracture
obtained from the load-displacement curve of SENB test was 22.8
kJ.m-2. The composites exhibited excellent impact resistance and the
dynamic fracture toughness of 44.8 kJ.m-2 is achieved as determined
from instrumented Charpy impact test. The shear strength of the
composite was 93 MPa, which is significantly higher compared 2-D
Cf/SiC composites. Microstructure evaluation of fracture surfaces
revealed the signatures of fracture processes and showed good
support for the higher toughness obtained.
Abstract: With the rapid progress of modern cities, the railway
construction must be developing quickly in China.As a typical
high-density country, shopping center on the subway should be one
important factor during the process of urban development. The paper
discusses the influence of the layout of shopping center on the subway,
and put it in the time and space’s axis of Shanghai urban development.
We usethe digital technology to establish the database of relevant
information. And then get the change role about shopping center on
subway in Shanghaiby the Kernel density estimate.The result shows
the development of shopping center on subway has a relationship with
local economic strength, population size, policysupport, and city
construction. And the suburbanization trend of shopping center would
be increasingly significant.By this case research, we could see the
Kernel density estimate is an efficient analysis method on the spatial
layout. It could reveal the characters of layout form of shopping center
on subway in essence. And it can also be applied to the other research
of space form.
Abstract: Most flexible rotors can be considered as beam-like
structures. In many cases, rotors are modeled as one-dimensional
bodies, made basically of beam-like shafts with rigid bodies attached
to them. This approach is typical of rotor dynamics, both analytical
and numerical, and several rotor dynamic codes, based on the finite
element method, follow this trend. In this paper, a finite element
model based on Timoshenko beam elements is utilized to analyze the
lateral dynamic behavior of a certain rotor-bearing system in
operating conditions.
Abstract: Application of hulls processing technologies, based on high-concentrated energy sources (laser and plasma technologies), allow improve shipbuilding production. It is typical for high-speed vessels construction using steel and aluminum alloys with high precision hulls required. Report describes high-performance technologies for plasma welding (using direct current of reversed polarity), laser, and hybrid laser-arc welding of hulls structures developed by JSC “SSTC”
Abstract: ‘Steganalysis’ is one of the challenging and attractive interests for the researchers with the development of information hiding techniques. It is the procedure to detect the hidden information from the stego created by known steganographic algorithm. In this paper, a novel feature based image steganalysis technique is proposed. Various statistical moments have been used along with some similarity metric. The proposed steganalysis technique has been designed based on transformation in four wavelet domains, which include Haar, Daubechies, Symlets and Biorthogonal. Each domain is being subjected to various classifiers, namely K-nearest-neighbor, K* Classifier, Locally weighted learning, Naive Bayes classifier, Neural networks, Decision trees and Support vector machines. The experiments are performed on a large set of pictures which are available freely in image database. The system also predicts the different message length definitions.
Abstract: The need to extract R&D keywords from issues and use
them to retrieve R&D information is increasing rapidly. However, it is
difficult to identify related issues or distinguish them. Although the
similarity between issues cannot be identified, with an R&D lexicon,
issues that always share the same R&D keywords can be determined.
In detail, the R&D keywords that are associated with a particular issue
imply the key technology elements that are needed to solve a particular
issue.
Furthermore, the relationship among issues that share the same
R&D keywords can be shown in a more systematic way by clustering
them according to keywords. Thus, sharing R&D results and reusing
R&D technology can be facilitated. Indirectly, redundant investment
in R&D can be reduced as the relevant R&D information can be shared
among corresponding issues and the reusability of related R&D can be
improved. Therefore, a methodology to cluster issues from the
perspective of common R&D keywords is proposed to satisfy these
demands.
Abstract: This paper presents a regression model with
autocorrelated errors in which the inputs are social moods obtained by
analyzing the adjectives in Twitter posts using a document topic
model, where document topics are extracted using LDA. The
regression model predicts Dow Jones Industrial Average (DJIA) more
precisely than autoregressive moving-average models.
Abstract: The biomass-based fuels have become great concern in order to replace the petroleum-based fuels. Biofuels are a wide range of fuels referred to liquid, gas and solid fuels produced from biomass. Recently, higher chain alcohols such as 3-methyl-1-butanol and isobutanol have become a better candidate compared to bioethanol in order to replace gasoline as transportation fuel. Therefore, in this study, 3-methyl-1-butanol was produced through a fermentation process by yeast. Several types of yeast involved in this research including Saccharomyces cerevisiae, Kluyveromyces lactis GG799 and Pichia pastoris (KM71H, GS115 and X33). The result obtained showed that K. lactis GG799 gave the highest concentration of 3-methyl-1-butanol at 274 mg/l followed by S. cerevisiae, P. pastoris GS115, P. pastoris KM71H and P. pastoris X33 at 265 mg/l, 190 mg/l, 182 mg/l and 174 mg/l respectively. Based on the result, it proved that yeast have a potential in producing 3-methyl-1-butanol naturally.
Abstract: Abundant and cheap agricultural waste of oil palm trunk (OPT) juice was used to produce bioethanol. Two strains of Saccharomyces cerevisiae and a strain of Pichia stipitis were used to produce bioethanol from the OPT juice. Fermentation was conducted at previously optimized condition at 30oC and without shaking. The kinetic parameters were estimated and calculated. Monod equation and Hinshelwood model is used to relate the specific growth to the concentration of the limiting substrate and also to simulate bioethanol production rate. Among the three strains, single S. cerevisiae Kyokai no. 7 produce the highest ethanol yield of 0.477 g/l.h within the shortest time (12 h). This yeast also produces more than 20 g/l ethanol concentration within 10 h of fermentation.