Abstract: The Constraints imposed by non-thermal
leptogenesis on the survival of the neutrino mass models describing
the presently available neutrino mass patterns, are studied
numerically. We consider the Majorana CP violating phases coming
from right-handed Majorana mass matrices to estimate the baryon
asymmetry of the universe, for different neutrino mass models
namely quasi-degenerate, inverted hierarchical and normal
hierarchical models, with tribimaximal mixings. Considering two
possible diagonal forms of Dirac neutrino mass matrix as either
charged lepton or up-quark mass matrix, the heavy right-handed
mass matrices are constructed from the light neutrino mass matrix.
Only the normal hierarchical model leads to the best predictions of
baryon asymmetry of the universe, consistent with observations in
non-thermal leptogenesis scenario.
Abstract: This paper presents a novel three-phase utility
frequency to high frequency soft switching power conversion circuit
with dual mode pulse width modulation and pulse density modulation
for high power induction heating applications as melting of steel and
non ferrous metals, annealing of metals, surface hardening of steel
and cast iron work pieces and hot water producers, steamers and
super heated steamers. This high frequency power conversion circuit
can operate from three-phase systems to produce high current for
high power induction heating applications under the principles of
ZVS and it can regulate its ac output power from the rated value to a
low power level. A dual mode modulation control scheme based on
high frequency PWM in synchronization with the utility frequency
positive and negative half cycles for the proposed high frequency
conversion circuit and utility frequency pulse density modulation is
produced to extend its soft switching operating range for wide ac
output power regulation. A dual packs heat exchanger assembly is
designed to be used in consumer and industrial fluid pipeline systems
and it is proved to be suitable for the hot water, steam and super
heated steam producers. Experiment and simulation results are given
in this paper to verify the operation principles of the proposed ac
conversion circuit and to evaluate its power regulation and
conversion efficiency. Also, the paper presents a mutual coupling
model of the induction heating load instead of equivalent transformer
circuit model.
Abstract: The objective of this paper is to present a
comparative study of Homotopy Perturbation Method (HPM),
Variational Iteration Method (VIM) and Homotopy Analysis
Method (HAM) for the semi analytical solution of Kortweg-de
Vries (KdV) type equation called KdV. The study have been
highlighted the efficiency and capability of aforementioned methods
in solving these nonlinear problems which has been arisen from a
number of important physical phenomenon.
Abstract: In the current decade, wireless sensor networks are
emerging as a peculiar multi-disciplinary research area. By this
way, energy efficiency is one of the fundamental research themes
in the design of Medium Access Control (MAC) protocols for
wireless sensor networks. Thus, in order to optimize the energy
consumption in these networks, a variety of MAC protocols are
available in the literature. These schemes were commonly evaluated
under simple network density and a few results are published on
their robustness in realistic network-s size. We, in this paper, provide
an analytical study aiming to highlight the energy waste sources in
wireless sensor networks. Then, we experiment three energy efficient
hybrid CSMA/CA based MAC protocols optimized for wireless
sensor networks: Sensor-MAC (SMAC), Time-out MAC (TMAC)
and Traffic aware Energy Efficient MAC (TEEM). We investigate
these protocols with different network densities in order to discuss
the end-to-end performances of these schemes (i.e. in terms of energy
efficiency, delay and throughput). Through Network Simulator (NS-
2) implementations, we explore the behaviors of these protocols with
respect to the network density. In fact, this study may help the multihops
sensor networks designers to design or select the MAC layer
which matches better their applications aims.
Abstract: Banyan networks are really attractive for serving as
the optical switching architectures due to their unique properties of
small depth and absolute signal loss uniformity. The fact has been
established that the limitations of blocking nature and the nonavailability
of proper connections due to non-rearrangeable property
can be easily ruled out using electro-optic MZI switches as basic
switching elements. Combination of the horizontal expansion and
vertical stacking of optical banyan networks is an appropriate scheme
for constructing non-blocking banyan-based optical switching
networks. The interconnected banyan switching fabrics (IBSF) have
been considered and analyzed to best serve the purpose of optical
switching with electro-optic MZI basic elements. The cross/bar state
interchange for the switches has been facilitated by appropriate
voltage switching or the by the switching of operating wavelength.
The paper is dedicated to the modification of the basic switching
element being used as well as the architecture of the switching
network.
Abstract: Most HWRs currently use natural uranium fuel. Using enriched uranium fuel results in a significant improvement in fuel cycle costs and uranium utilization. On the other hand, reactivity changes of HWRs over the full range of operating conditions from cold shutdown to full power are small. This reduces the required reactivity worth of control devices and minimizes local flux distribution perturbations, minimizing potential problems due to transient local overheating of fuel. Analyzing heavy water effectiveness on neutronic parameters such as enrichment requirements, peaking factor and reactivity is important and should pay attention as primary concepts of a HWR core designing. Two nuclear nuclear reactors of CANDU-type and hexagonal-type reactor cores of 33 fuel assemblies and 19 assemblies in 1.04 P/D have been respectively simulated using MCNP-4C code. Using heavy water and light water as moderator have been compared for achieving less reactivity insertion and enrichment requirements. Two fuel matrixes of (232Th/235U)O2 and (238/235U)O2 have been compared to achieve more economical and safe design. Heavy water not only decreased enrichment needs, but it concluded in negative reactivity insertions during moderator density variations. Thorium oxide fuel assemblies of 2.3% enrichment loaded into the core of heavy water moderator resulted in 0.751 fission to absorption ratio and peaking factor of 1.7 using. Heavy water not only provides negative reactivity insertion during temperature raises which changes moderator density but concluded in 2 to 10 kg reduction of enrichment requirements, depend on geometry type.
Abstract: In many ways, biomedical analysis is analogous to possibilistic reasoning. In spite of that, there are hardly any applications of possibility theory in biology or medicine. The aim of this work is to demonstrate the use of possibility theory in an epidemiological study. In the paper, we build the possibility distribution for the controlled bloodstream concentrations of any physiologically active substance through few approximate considerations. This possibility distribution is tested later against the empirical histograms obtained from the panel study of the eight different physiologically active substances in 417 individuals.
Abstract: The most common forensic activity is searching a hard
disk for string of data. Nowadays, investigators and analysts are
increasingly experiencing large, even terabyte sized data sets when
conducting digital investigations. Therefore consecutive searching can
take weeks to complete successfully. There are two primary search
methods: index-based search and bitwise search. Index-based
searching is very fast after the initial indexing but initial indexing
takes a long time. In this paper, we discuss a high speed bitwise search
model for large-scale digital forensic investigations. We used pattern
matching board, which is generally used for network security, to
search for string and complex regular expressions. Our results indicate
that in many cases, the use of pattern matching board can substantially
increase the performance of digital forensic search tools.
Abstract: The success of an electronic system in a System-on- Chip is highly dependent on the efficiency of its interconnection network, which is constructed from routers and channels (the routers move data across the channels between nodes). Since neither classical bus based nor point to point architectures can provide scalable solutions and satisfy the tight power and performance requirements of future applications, the Network-on-Chip (NoC) approach has recently been proposed as a promising solution. Indeed, in contrast to the traditional solutions, the NoC approach can provide large bandwidth with moderate area overhead. The selected topology of the components interconnects plays prime rule in the performance of NoC architecture as well as routing and switching techniques that can be used. In this paper, we present two generic NoC architectures that can be customized to the specific communication needs of an application in order to reduce the area with minimal degradation of the latency of the system. An experimental study is performed to compare these structures with basic NoC topologies represented by 2D mesh, Butterfly-Fat Tree (BFT) and SPIN. It is shown that Cluster mesh (CMesh) and MinRoot schemes achieves significant improvements in network latency and energy consumption with only negligible area overhead and complexity over existing architectures. In fact, in the case of basic NoC topologies, CMesh and MinRoot schemes provides substantial savings in area as well, because they requires fewer routers. The simulation results show that CMesh and MinRoot networks outperforms MESH, BFT and SPIN in main performance metrics.
Abstract: This article discusses the problem of estimating the
orientation of inclined ground on which a human subject stands based
on information provided by the vestibular system consisting of the
otolith and semicircular canals. It is assumed that body segments are
not necessarily aligned and thus forming an open kinematic chain.
The semicircular canals analogues to a technical gyrometer provide a
measure of the angular velocity whereas the otolith analogues to a
technical accelerometer provide a measure of the translational
acceleration. Two solutions are proposed and discussed. The first is
based on a stand-alone Kalman filter that optimally fuses the two
measurements based on their dynamic characteristics and their noise
properties. In this case, no body dynamic model is needed. In the
second solution, a central extended disturbance observer that
incorporates a body dynamic model (internal model) is employed.
The merits of both solutions are discussed and demonstrated by
experimental and simulation results.
Abstract: Constant amplitude fatigue crack growth (FCG) tests
were performed on dissimilar metal welded plates of Type 316L
Stainless Steel (SS) and IS 2062 Grade A Carbon steel (CS). The
plates were welded by TIG welding using SS E309 as electrode. FCG
tests were carried on the Side Edge Notch Tension (SENT)
specimens of 5 mm thickness, with crack initiator (notch) at base
metal region (BM), weld metal region (WM) and heat affected zones
(HAZ). The tests were performed at a test frequency of 10 Hz and at
load ratios (R) of 0.1 & 0.6. FCG rate was found to increase with
stress ratio for weld metals and base metals, where as in case of
HAZ, FCG rates were almost equal at high ΔK. FCG rate of HAZ of
stainless steel was found to be lowest at low and high ΔK. At
intermediate ΔK, WM showed the lowest FCG rate. CS showed
higher crack growth rate at all ΔK. However, the scatter band of data
was found to be narrow. Fracture toughness (Kc) was found to vary
in different locations of weldments. Kc was found lowest for the
weldment and highest for HAZ of stainless steel. A novel method of
characterizing the FCG behavior using an Infrared thermography
(IRT) camera was attempted. By monitoring the temperature rise at
the fast moving crack tip region, the amount of plastic deformation
was estimated.
Abstract: A Simultaneous Multithreading (SMT) Processor is
capable of executing instructions from multiple threads in the same
cycle. SMT in fact was introduced as a powerful architecture to
superscalar to increase the throughput of the processor.
Simultaneous Multithreading is a technique that permits multiple
instructions from multiple independent applications or threads to
compete limited resources each cycle. While the fetch unit has been
identified as one of the major bottlenecks of SMT architecture, several
fetch schemes were proposed by prior works to enhance the fetching
efficiency and overall performance.
In this paper, we propose a novel fetch policy called queue situation
identifier (QSI) which counts some kind of long latency instructions of
each thread each cycle then properly selects which threads to fetch
next cycle. Simulation results show that in best case our fetch policy
can achieve 30% on speedup and also can reduce the data cache level 1
miss rate.
Abstract: A simple network model is developed in OPNET to
study the performance of the Wi-Fi protocol. The model is simulated
in OPNET and performance factors such as load, throughput and delay
are analysed from the model. Four applications such as oracle, http, ftp
and voice are applied over the Wireless LAN network to determine the
throughput. The voice application utilises a considerable amount of
bandwidth of up to 5Mbps, as a result the 802.11g standard of the
Wi-Fi protocol was chosen which can support a data rate of up to
54Mbps. Results indicate that when the load in the Wi-Fi network is
increased the queuing delay on the point-to-point links in the Wi-Fi
network significantly reduces until it is comparable to that of WiMAX.
In conclusion, the queuing delay of the Wi-Fi protocol for the network
model simulated was about 0.00001secs comparable to WiMAX
network values.
Abstract: Acute toxicity of nano SiO2, ZnO, MCM-41 (Meso
pore silica), Cu, Multi Wall Carbon Nano Tube (MWCNT), Single
Wall Carbon Nano Tube (SWCNT) , Fe (Coated) to bacteria Vibrio
fischeri using a homemade luminometer , was evaluated. The values
of the nominal effective concentrations (EC), causing 20% and 50%
inhibition of biouminescence, using two mathematical models at two
times of 5 and 30 minutes were calculated. Luminometer was
designed with Photomultiplier (PMT) detector. Luminol
chemiluminescence reaction was carried out for the calibration graph.
In the linear calibration range, the correlation coefficients and
coefficient of Variation (CV) were 0.988 and 3.21% respectively
which demonstrate the accuracy and reproducibility of the instrument
that are suitable. The important part of this research depends on how
to optimize the best condition for maximum bioluminescence. The
culture of Vibrio fischeri with optimal conditions in liquid media,
were stirring at 120 rpm at a temperature of 150C to 180C and were
incubated for 24 to 72 hours while solid medium was held at 180C
and for 48 hours. Suspension of nanoparticles ZnO, after 30 min
contact time to bacteria Vibrio fischeri, showed the highest toxicity
while SiO2 nanoparticles showed the lowest toxicity. After 5 min
exposure time, the toxicity of ZnO was the strongest and MCM-41
was the weakest toxicant component.
Abstract: This paper presents the hardware design of a unified
architecture to compute the 4x4, 8x8 and 16x16 efficient twodimensional
(2-D) transform for the HEVC standard. This
architecture is based on fast integer transform algorithms. It is
designed only with adders and shifts in order to reduce the hardware
cost significantly. The goal is to ensure the maximum circuit reuse
during the computing while saving 40% for the number of operations.
The architecture is developed using FIFOs to compute the second
dimension. The proposed hardware was implemented in VHDL. The
VHDL RTL code works at 240 MHZ in an Altera Stratix III FPGA.
The number of cycles in this architecture varies from 33 in 4-point-
2D-DCT to 172 when the 16-point-2D-DCT is computed. Results
show frequency improvements reaching 96% when compared to an
architecture described as the direct transcription of the algorithm.
Abstract: Currently, a large number of license activities (Early
Site Permits, Combined Operating License, reactor certifications,
etc.), are pending for review before the United States Nuclear
Regulatory Commission (US NRC). Much of the senior staff at the
NRC is now committed to these review and licensing actions. To
address this additional workload, the NRC has recruited a large
number of new Regulatory Staff for dealing with these and other
regulatory actions such as the US Fleet of Research and Test Reactors
(RTRs). These reactors pose unusual demands on Regulatory Staff
since the US Fleet of RTRs, although few (32 Licensed RTRs as of
2010), they represent a broad range of reactor types, operations, and
research and training aspects that nuclear reactor power plants (such
as the 104 LWRs) do not pose. The NRC must inspect and regulate
all these facilities. This paper addresses selected training topics and
regulatory activities providedNRC Inspectors for RTRs.
Abstract: Inflammatory bowel disease (IBD) is a chronic
relapsing-remitting condition that afflicts millions of people
throughout the world and impairs their daily functions and quality of
life. Treatment of IBD depends largely on 5-aminosalicylic acid (5-
ASA) and corticosteroids. The present study aimed to clarify the
effects of 5-aminosalicylic acid, budesonide and currcumin on 90
male albino rats against trinitrobenzene sulfonic acid (TNB) induced
colitis. TNB was injected intrarectally to 50 rats. The other 40 rats
served as control groups. Both 5-ASA (in a dose of 120 mg/kg) and
budesonide (in a dose of 0.1 mg/kg) were administered daily for one
week whereas currcumin was injected intraperitonially (in a dose of
30 mg/kg daily) for 14 days after injection of either TNB in the
colitis rats (group B) or saline in control groups (group A). The study
included estimation of macroscopic score index, histological
examination of H&E stained sections of the colonic tissue,
biochemical estimation of myeloperoxidase (MPO), nitric oxide
(NO), and caspase-3 levels, in addition to studying the effect of tested
drugs on colonic motility. It was found that budesonide and curcumin
improved mucosal healing, reduced both NO production and caspase-
3 level. They had the best impact on the disturbed colonic motility in
TNBS-model of colitis.
Abstract: Homogeneous composites of alumina and zirconia
with a small amount of MgO (99%) were obtained for ZTA ceramic containing 0.05 wt% MgO in
1500 °C.
Abstract: Use of microemulsion in enhanced oil recovery has become more attractive in recent years because of its high level of extraction efficiency. Experimental investigations have been made on characterization of microemulsions of oil-brinesurfactant/ cosurfactant system for its use in enhanced oil recovery (EOR). Sodium dodecyl sulfate, propan-1-ol and heptane were selected as surfactant, cosurfactant and oil respectively for preparation of microemulsion. The effects of salinity on the relative phase volumes and solubilization parameters have also been studied. As salinity changes from low to high value, phase transition takes place from Winsor I to Winsor II via Winsor III. Suitable microemulsion composition has been selected based on its stability and ability to reduce interfacial tension. A series of flooding experiments have been performed using the selected microemulsion. The flooding experiments were performed in a core flooding apparatus using uniform sand pack. The core holder was tightly packed with uniform sands (60-100 mesh) and saturated with brines of different salinities. It was flooded with the brine at 25 psig and the absolute permeability was calculated from the flow rate of the through sand pack. The sand pack was then flooded with the crude oil at 800 psig to irreducible water saturation. The initial water saturation was determined on the basis of mass balance. Waterflooding was conducted by placing the coreholder horizontally at a constant injection pressure at 200 pisg. After water flooding, when water-cut reached above 95%, around 0.5 pore volume (PV) of the above microemulsion slug was injected followed by chasing water. The experiments were repeated using different composition of microemulsion slug. The additional recoveries were calculated by material balance. Encouraging results with additional recovery more than 20% of original oil in place above the conventional water flooding have been observed.
Abstract: Verapamil has been shown to inhibit fentanyl uptake in vitro and is a potent P-glycoprotein inhibitor. Tissue partitioning of loperamide, a commercially available opioid, is closely controlled by the P-gp efflux transporter. The following studies were designed to evaluate the effect of opioids on verapamil partitioning in the lung and brain, in vivo. Opioid (fentanyl or loperamide) was administered by intravenous infusion to Sprague Dawley rats alone or in combination with verapamil and plasma, with lung and brain tissues were collected at 1, 5, 6, 8, 10 and 60 minutes. Drug dispositions were modeled by recirculatory pharmacokinetic models. Fentanyl slightly increased the verapamil lung (PL) partition coefficient yet decreased the brain (PB) partition coefficient. Furthermore, loperamide significantly increased PLand PB. Fentanyl reduced the verapamil volume of distribution (V1) and verapamil elimination clearance (ClE). Fentanyl decreased verapamil brain partitioning, yet increased verapamil lung partitioning. Also, loperamide increased lung and brain partitioning in vivo. These results suggest that verapamil and fentanyl may be substrates of an unidentified inward transporter in brain tissue and confirm that verapamil and loperamide are substrates of the efflux transporter P-gp.