Abstract: The Linear discriminant analysis (LDA) can be
generalized into a nonlinear form - kernel LDA (KLDA) expediently
by using the kernel functions. But KLDA is often referred to a general
eigenvalue problem in singular case. To avoid this complication, this
paper proposes an iterative algorithm for the two-class KLDA. The
proposed KLDA is used as a nonlinear discriminant classifier, and the
experiments show that it has a comparable performance with SVM.
Abstract: The successful use of CDMA technology is based on
the construction of large families of encoding sequences with good
correlation properties. This paper discusses PN sequence generation
based on Residue Arithmetic with an effort to improve the performance
of existing interference-limited CDMA technology for mobile
cellular systems. All spreading codes with residual number system
proposed earlier did not consider external interferences, multipath
propagation, Doppler effect etc. In literature the use of residual
arithmetic in DS-CDMA was restricted to encoding of already spread
sequence; where spreading of sequence is done by some existing
techniques. The novelty of this paper is the use of residual number
system in generation of the PN sequences which is used to spread
the message signal. The significance of cross-correlation factor in
alleviating multi-access interference is also discussed. The RNS based
PN sequence has superior performance than most of the existing
codes that are widely used in DS-CDMA applications. Simulation
results suggest that the performance of the proposed system is
superior to many existing systems.
Abstract: Significant changes in oil and gas drilling have
emphasized the need to verify the integrity and reliability of drill
stem components. Defects are inevitable in cast components,
regardless of application; but if these defects go undetected, any
severe defect could cause down-hole failure.
One such defect is shrinkage porosity. Castings with lower level
shrinkage porosity (CB levels 1 and 2) have scattered pores and do
not occupy large volumes; so pressure testing and helium leak testing
(HLT) are sufficient for qualifying the castings. However, castings
with shrinkage porosity of CB level 3 and higher, behave erratically
under pressure testing and HLT making these techniques insufficient
for evaluating the castings- integrity.
This paper presents a case study to highlight how the radiography
technique is much more effective than pressure testing and HLT.
Abstract: Due to the non- intuitive nature of Quantum
algorithms, it becomes difficult for a classically trained person to
efficiently construct new ones. So rather than designing new
algorithms manually, lately, Genetic algorithms (GA) are being
implemented for this purpose. GA is a technique to automatically
solve a problem using principles of Darwinian evolution. This has
been implemented to explore the possibility of evolving an n-qubit
circuit when the circuit matrix has been provided using a set of
single, two and three qubit gates. Using a variable length population
and universal stochastic selection procedure, a number of possible
solution circuits, with different number of gates can be obtained for
the same input matrix during different runs of GA. The given
algorithm has also been successfully implemented to obtain two and
three qubit Boolean circuits using Quantum gates. The results
demonstrate the effectiveness of the GA procedure even when the
search spaces are large.
Abstract: With the rapid expansion of city scale and the
excessive concentration of population, achieving relative equality of
extracurricular education resources and improving spatial service
performance of relevant facilities become necessary arduous tasks. In
urban space, extracurricular education facilities should offer better
service to its targeted area and promote the equality and efficiency of
education, which is accomplished by the allocation of facilities. Based
on questionnaire and survey for local students in Hangzhou City in
2009, this study classifies extracurricular education facilities in
meg-city and defines the equalization of these facilities. Then it is
suggested to establish extracurricular education facilities system
according to the development level of city and demands of local
students, and to introduce a spatial analysis method into urban
planning through the aspects of spatial distribution, travel cost and
spatial service scope. Finally, the practice of nine sub-districts of
Hangzhou is studied.
Abstract: The present paper considers the steady free
convection boundary layer flow of a viscoelastics fluid with constant
temperature in the presence of heat generation. The boundary layer
equations are an order higher than those for the Newtonian (viscous)
fluid and the adherence boundary conditions are insufficient to
determine the solution of these equations completely. The governing
boundary layer equations are first transformed into non-dimensional
form by using special dimensionless group. Computations are
performed numerically by using Keller-box method by augmenting
an extra boundary condition at infinity and the results are displayed
graphically to illustrate the influence of viscoelastic K, heat
generation γ , and Prandtl Number, Pr parameters on the velocity
and temperature profiles. The results of the surface shear stress in
terms of the local skin friction and the surface rate of heat transfer in
terms of the local Nusselt number for a selection of the heat
generation parameterγ (=0.0, 0.2, 0.5, 0.8, 1.0) are obtained and
presented in both tabular and graphical formats. Without effect of the
internal heat generation inside the fluid domain for which we take
γ = 0.0, the present numerical results show an excellent agreement
with previous publication.
Abstract: We present a white LED-based optical wireless
communication systems for indoor ubiquitous sensor networks. Each
sensor node could access to the server through the PLC (Power Line
Communication)-Ethernet interface. The proposed system offers a
full-duplex wireless link by using different wavelengths to reduce the
inter-symbol interference between uplink and downlink. Through the
1-to-n optical wireless sensor network and PLC modem, the mobile
terminals send a temperature data to server. The data transmission
speed and distance are 115.2kbps and about 60cm, respectively.
Abstract: In this paper the application of neuro-fuzzy system for equalization of channel distortion is considered. The structure and operation algorithm of neuro-fuzzy equalizer are described. The use of neuro-fuzzy equalizer in digital signal transmission allows to decrease training time of parameters and decrease the complexity of the network. The simulation of neuro-fuzzy equalizer is performed. The obtained result satisfies the efficiency of application of neurofuzzy technology in channel equalization.
Abstract: In this paper, Differential Evolution (DE) algorithm, a new promising evolutionary algorithm, is proposed to train Radial Basis Function (RBF) network related to automatic configuration of network architecture. Classification tasks on data sets: Iris, Wine, New-thyroid, and Glass are conducted to measure the performance of neural networks. Compared with a standard RBF training algorithm in Matlab neural network toolbox, DE achieves more rational architecture for RBF networks. The resulting networks hence obtain strong generalization abilities.
Abstract: The classic problem of recovering arbitrary values of
a band-limited signal from its samples has an added complication
in software radio applications; namely, the resampling calculations
inevitably fold aliases of the analog signal back into the original
bandwidth. The phenomenon is quantified by the spur-free dynamic
range. We demonstrate how a novel application of the Remez (Parks-
McClellan) algorithm permits optimal signal recovery and SFDR, far
surpassing state-of-the-art resamplers.
Abstract: Carbon nanotubes (CNTs) are attractive because of
their excellent chemical durability mechanical strength and electrical
properties. Therefore there is interest in CNTs for not only electrical
and mechanical application, but also biological and medical
application.
In this study, the dispersion power of surfactant-treated multiwalled
carbon nanotubes (MWCNTs) and their effect on the antibacterial
activity were examined. Surfactant was used sodium
dodecyl-benzenesulfonate (SDBS). UV-vis absorbance and
transmission electron microscopy(TEM) were used to characterize the
dispersion of MWCNTs in the aqueous phase, showing that the
surfactant molecules had been adsorbed onto the MWCNTs surface.
The surfactant-treated MWCNTs exhibited antimicrobial activities
to streptococcus mutans. The optical density growth curves and viable
cell number determined by the plating method suggested that the
antimicrobial activity of surfactant-treated MWCNTs was both
concentration and treatment time-dependent.
Abstract: This paper presents the design and implementation of a fully integrated transimpedance amplifier (TIA) as the analog frontend receiver for Capacitive Micromachined Ultrasound Transducers (CMUTs) for ultrasound biomicroscope imaging application. The amplifier is designed to amplify the received signals from 17.5MHz to 52.5MHz with a center frequency of 35MHz. The TIA was fabricated in GF 0.18μm 1P6M 30V high voltage process. The measurement results show that the designed amplifier can reach a transimpedance gain of 61.08dBΩ and operating frequency from 17.5MHz to 100MHz with 1VP-P output voltage under 6V power supply.
Abstract: User interaction components of Augmented Reality (AR) systems have to be tested with users in order to find and fix usability problems as early as possible. In this paper we will report on a user-centered design approach for AR systems following the experience acquired during the design and evaluation of a software prototype for an AR-based educational platform. In this respect we will focus on the re-design of the user task based on the results from a formative usability evaluation. The basic idea of our approach is to describe task scenarios in a tabular format, to develop a task model in a task modeling environment and then to simulate the execution.
Abstract: Group work, projects and discussions are important
components of teacher education courses whether they are face-toface,
blended or exclusively online formats. This paper examines the varieties of tasks and challenges with this learning format in a face to
face class teacher education class providing specific examples of both
failure and success from both the student and instructor perspective.
The discussion begins with a brief history of collaborative and cooperative learning, moves to an exploration of the promised
benefits and then takes a look at some of the challenges which can
arise specifically from the use of new technologies. The discussion concludes with guidelines and specific suggestions.
Abstract: The experiment was performed to evaluate the effect
of GA3, 2,4-D on fruit growth and fruit quality of wax apple. The
experiment consisted of Red A, Monulla, Atu, Red B cultivars. GA3
and 2,4-D were applied at the small bud and petal fall stage.
Physiological, biochemical characters of fruit were recoded. The
result showed application of GA3, 2,4-D greatly response in
increasing fruit set for all treatment as compared to control. Fruit
weight, fruit size were increased at 10 ppm 2,4-D in ‘Red A’, ‘Red
B’, however it was also enhancing at 10 ppm GA3 in ‘Monulla’,
‘Atu’. For ‘Monulla’, ‘Atu’ fruit crack reduced by 10 ppm 2,4-D
application, but ‘Red B’, ‘Red A’ gave least fruit crack at 10 and 30
ppm GA3, respectively. ‘Monulla’, ‘Atu’ and ‘Red B’ resulted in
response well to 10 ppm GA3 on improving TSS, whereas
application of 30 ppm GA3 greatly enhancing TSS in ‘Red A’. For
‘Atu’ titratable acidity markedly reduced by 10 ppm GA3
application, but spraying with 30 ppm GA3 greatly response in
reducing titratable acidity in ‘Red A’, ‘Red B’ and ‘Monulla’. It was
concluded that GA3, 2,4-D can be an effective tool to enhancing fruit
set, fruit growth as well as improving fruit quality of wax apple.
Abstract: There are many researches to detect collision between real object and virtual object in 3D space. In general, these techniques are need to huge computing power. So, many research and study are constructed by using cloud computing, network computing, and distribute computing. As a reason of these, this paper proposed a novel fast 3D collision detection algorithm between real and virtual object using 2D intersection area. Proposed algorithm uses 4 multiple cameras and coarse-and-fine method to improve accuracy and speed performance of collision detection. In the coarse step, this system examines the intersection area between real and virtual object silhouettes from all camera views. The result of this step is the index of virtual sensors which has a possibility of collision in 3D space. To decide collision accurately, at the fine step, this system examines the collision detection in 3D space by using the visual hull algorithm. Performance of the algorithm is verified by comparing with existing algorithm. We believe proposed algorithm help many other research, study and application fields such as HCI, augmented reality, intelligent space, and so on.
Abstract: This study extends research on the relationship
between marketing strategy and market segmentation by
investigating on market segments in the cement industry.
Competitive strength and rivals distance from the factory were used
as business environment. A three segment (positive, neutral or
indifferent and zero zones) were identified as strategic segments. For
each segment a marketing strategy (aggressive, defensive and
decline) were developed. This study employed data from cement
industry to fulfill two objectives, the first is to give a framework to
the segmentation of cement industry and the second is developing
marketing strategy with varying competitive strength. Fifty six
questionnaires containing close-and open-ended questions were
collected and analyzed. Results supported the theory that segments
tend to be more aggressive than defensive when competitive strength
increases. It is concluded that high strength segments follow total
market coverage, concentric diversification and frontal attack to their
competitors. With decreased competitive strength, Business tends to
follow multi-market strategy, product modification/improvement and
flank attack to direct competitors for this kind of segments. Segments
with weak competitive strength followed focus strategy and decline
strategy.
Abstract: Recently, the improvements in processing performance
of a computer and in high speed communication of an optical fiber
have been achieved, so that the amount of data which are processed
by a computer and flowed on a network has been increasing greatly.
However, in a client-server system, since the server receives and
processes the amount of data from the clients through the network, a
load on the server is increasing. Thus, there are needed to introduce
a server with high processing ability and to have a line with high
bandwidth. In this paper, concerning to P2P networks to resolve the
load on a specific server, a criterion called an Indexed-Priority Metric
is proposed and its performance is evaluated. The proposed metric is
to allocate some files to each node. As a result, the load on a specific
server can distribute them to each node equally well. A P2P file
sharing system using the proposed metric is implemented. Simulation
results show that the proposed metric can make it distribute files on
the specific server.
Abstract: Context awareness is a capability whereby mobile
computing devices can sense their physical environment and adapt
their behavior accordingly. The term context-awareness, in
ubiquitous computing, was introduced by Schilit in 1994 and has
become one of the most exciting concepts in early 21st-century
computing, fueled by recent developments in pervasive computing
(i.e. mobile and ubiquitous computing). These include computing
devices worn by users, embedded devices, smart appliances, sensors
surrounding users and a variety of wireless networking technologies.
Context-aware applications use context information to adapt
interfaces, tailor the set of application-relevant data, increase the
precision of information retrieval, discover services, make the user
interaction implicit, or build smart environments. For example: A
context aware mobile phone will know that the user is currently in a
meeting room, and reject any unimportant calls. One of the major
challenges in providing users with context-aware services lies in
continuously monitoring their contexts based on numerous sensors
connected to the context aware system through wireless
communication. A number of context aware frameworks based on
sensors have been proposed, but many of them have neglected the
fact that monitoring with sensors imposes heavy workloads on
ubiquitous devices with limited computing power and battery. In this
paper, we present CALEEF, a lightweight and energy efficient
context aware framework for resource limited ubiquitous devices.
Abstract: The current study describes a multi-objective optimization technique for positioning of houses in a residential neighborhood. The main task is the placement of residential houses in a favorable configuration satisfying a number of objectives. Solving the house layout problem is a challenging task. It requires an iterative approach to satisfy design requirements (e.g. energy efficiency, skyview, daylight, roads network, visual privacy, and clear access to favorite views). These design requirements vary from one project to another based on location and client preferences. In the Gulf region, the most important socio-cultural factor is the visual privacy in indoor space. Hence, most of the residential houses in this region are surrounded by high fences to provide privacy, which has a direct impact on other requirements (e.g. daylight and direction to favorite views). This investigation introduces a novel technique to optimally locate and orient residential buildings to satisfy a set of design requirements. The developed technique explores the search space for possible solutions. This study considers two dimensional house planning problems. However, it can be extended to solve three dimensional cases.