Abstract: In this paper, we use Radial Basis Function Networks
(RBFN) for solving the problem of environmental interference
cancellation of speech signal. We show that the Second Order Thin-
Plate Spline (SOTPS) kernel cancels the interferences effectively.
For make comparison, we test our experiments on two conventional
most used RBFN kernels: the Gaussian and First order TPS (FOTPS)
basis functions. The speech signals used here were taken from the
OGI Multi-Language Telephone Speech Corpus database and were
corrupted with six type of environmental noise from NOISEX-92
database. Experimental results show that the SOTPS kernel can
considerably outperform the Gaussian and FOTPS functions on
speech interference cancellation problem.
Abstract: The switching lag-time and the voltage drop across
the power devices cause serious waveform distortions and
fundamental voltage drop in pulse width-modulated inverter output.
These phenomenons are conspicuous when both the output frequency
and voltage are low. To estimate the output voltage from the PWM
reference signal it is essential to take account of these imperfections
and to correct them. In this paper, on-line compensation method is
presented. It needs three simple blocs to add at the ideal reference
voltages. This method does not require any additional hardware
circuit and off- line experimental measurement. The paper includes
experimental results to demonstrate the validity of the proposed
method. It is applied, finally, in case of indirect vector controlled
induction machine and implemented using dSpace card.
Abstract: Bloom filter is a probabilistic and memory efficient
data structure designed to answer rapidly whether an element is
present in a set. It tells that the element is definitely not in the set but
its presence is with certain probability. The trade-off to use Bloom
filter is a certain configurable risk of false positives. The odds of a
false positive can be made very low if the number of hash function is
sufficiently large. For spam detection, weight is attached to each set
of elements. The spam weight for a word is a measure used to rate the
e-mail. Each word is assigned to a Bloom filter based on its weight.
The proposed work introduces an enhanced concept in Bloom filter
called Bin Bloom Filter (BBF). The performance of BBF over
conventional Bloom filter is evaluated under various optimization
techniques. Real time data set and synthetic data sets are used for
experimental analysis and the results are demonstrated for bin sizes 4,
5, 6 and 7. Finally analyzing the results, it is found that the BBF
which uses heuristic techniques performs better than the traditional
Bloom filter in spam detection.
Abstract: Missing data yields many analysis challenges. In case of complex survey design, in addition to dealing with missing data, researchers need to account for the sampling design to achieve useful inferences. Methods for incorporating sampling weights in neural network imputation were investigated to account for complex survey designs. An estimate of variance to account for the imputation uncertainty as well as the sampling design using neural networks will be provided. A simulation study was conducted to compare estimation results based on complete case analysis, multiple imputation using a Markov Chain Monte Carlo, and neural network imputation. Furthermore, a public-use dataset was used as an example to illustrate neural networks imputation under a complex survey design
Abstract: In the paper we discuss the influence of the route
flexibility degree, the open rate of operations and the production type
coefficient on makespan. The flexible job-open shop scheduling
problem FJOSP (an extension of the classical job shop scheduling) is
analyzed. For the analysis of the production process we used a
hybrid heuristic of the GRASP (greedy randomized adaptive search
procedure) with simulated annealing algorithm. Experiments with
different levels of factors have been considered and compared. The
GRASP+SA algorithm has been tested and illustrated with results for
the serial route and the parallel one.
Abstract: Group contribution methods such as the UNIFAC are
very useful to researchers and engineers involved in synthesis,
feasibility studies, design and optimization of separation processes.
They can be applied successfully to predict phase equilibrium and
excess properties in the development of chemical and separation
processes. The main focus of this work was to investigate the
possibility of absorbing selected volatile organic compounds (VOCs)
into polydimethylsiloxane (PDMS) using three selected UNIFAC
group contribution methods. Absorption followed by subsequent
stripping is the predominant available abatement technology of
VOCs from flue gases prior to their release into the atmosphere. The
original, modified and effective UNIFAC models were used in this
work. The thirteen selected VOCs that have been considered in this
research are: pentane, hexane, heptanes, trimethylamine, toluene,
xylene, cyclohexane, butyl acetate, diethyl acetate, chloroform,
acetone, ethyl methyl ketone and isobutyl methyl ketone. The
computation was done for solute VOC concentration of 8.55x10-8
which is well in the infinite dilution region. The results obtained in
this study compare very well with those published in literature
obtained through both measurements and predictions. The phase
equilibrium obtained in this study show that PDMS is a good
absorbent for the removal of VOCs from contaminated air streams
through physical absorption.
Abstract: This paper deals with a high-order accurate Runge
Kutta Discontinuous Galerkin (RKDG) method for the numerical
solution of the wave equation, which is one of the simple case of a
linear hyperbolic partial differential equation. Nodal DG method is
used for a finite element space discretization in 'x' by discontinuous
approximations. This method combines mainly two key ideas which
are based on the finite volume and finite element methods. The
physics of wave propagation being accounted for by means of
Riemann problems and accuracy is obtained by means of high-order
polynomial approximations within the elements. High order accurate
Low Storage Explicit Runge Kutta (LSERK) method is used for
temporal discretization in 't' that allows the method to be nonlinearly
stable regardless of its accuracy. The resulting RKDG
methods are stable and high-order accurate. The L1 ,L2 and L∞ error
norm analysis shows that the scheme is highly accurate and effective.
Hence, the method is well suited to achieve high order accurate
solution for the scalar wave equation and other hyperbolic equations.
Abstract: Human heart valves diseased by congenital heart
defects, rheumatic fever, bacterial infection, cancer may cause stenosis
or insufficiency in the valves. Treatment may be with medication but
often involves valve repair or replacement (insertion of an artificial
heart valve). Bileaflet mechanical heart valves (BMHVs) are widely
implanted to replace the diseased heart valves, but still suffer from
complications such as hemolysis, platelet activation, tissue
overgrowth and device failure. These complications are closely related
to both flow characteristics through the valves and leaflet dynamics. In
this study, the physiological flow interacting with the moving leaflets
in a bileaflet mechanical heart valve (BMHV) is simulated with a
strongly coupled implicit fluid-structure interaction (FSI) method
which is newly organized based on the Arbitrary-Lagrangian-Eulerian
(ALE) approach and the dynamic mesh method (remeshing) of
FLUENT. The simulated results are in good agreement with previous
experimental studies. This study shows the applicability of the present
FSI model to the complicated physics interacting between fluid flow
and moving boundary.
Abstract: We present a BeeBot, Binus Multi-client Intelligent Telepresence Robot, a custom-build robot system specifically designed for teleconference with multiple person using omni directional actuator. The robot is controlled using a computer networks, so the manager/supervisor can direct the robot to the intended person to start a discussion/inspection. People tracking and autonomous navigation are intelligent features of this robot. We build a web application for controlling the multi-client telepresence robot and open-source teleconference system used. Experimental result presented and we evaluated its performance.
Abstract: Single Minute Exchange of Dies (SMED) mainly focuses on recognition of internal and external activities. It is concerned particularly with transferring internal activities into external ones in as many numbers as possible, by also minimizing the internal ones. The validity of the method and procedures are verified by an application a Styrofoam manufacturing process where setup times are critical for time reduction. Significant time savings have been achieved with minimum investment. Further, the issues related with employer safety and ergonomics principles during die exchange are noted.
Abstract: Composite pins of rubber dust collected from tyre
retreading centres of trucks, cars and buses etc.and epoxy with
weight percentages of 10. 15, and 20 % of rubber (weight fractions of
9, 13 and 17 % respectively) have been prepared in house with the
help of a split wooden mould. The pins were tested in a pin-on-disc
wear monitor to determine the co-efficient of friction and weight
losses with varying speeds, loads and time. The wear volume and
wear rates have also been found out for all these three specimens.. It
is observed that all the specimens have exhibited very low coefficient
of friction and low wear rates under dry sliding condition. Out of the
above three samples tested, the specimen with 10 % rubber dust by
weight has shown lowest wear rates. However a peculiar result i.e
decreasing trend has been obtained with 20% reinforcement of rubber
in epoxy while rubbed against steel at varying speeds. This might
have occurred due to high surface finish of the disc and formation of
a thin transfer layer from the composite
Abstract: In this paper, we combine a probabilistic neural method with radial-bias functions in order to construct the lithofacies of the wells DF01, DF02 and DF03 situated in the Triassic province of Algeria (Sahara). Lithofacies is a crucial problem in reservoir characterization. Our objective is to facilitate the experts' work in geological domain and to allow them to obtain quickly the structure and the nature of lands around the drilling. This study intends to design a tool that helps automatic deduction from numerical data. We used a probabilistic formalism to enhance the classification process initiated by a Self-Organized Map procedure. Our system gives lithofacies, from well-log data, of the concerned reservoir wells in an aspect easy to read by a geology expert who identifies the potential for oil production at a given source and so forms the basis for estimating the financial returns and economic benefits.
Abstract: The purpose of this paper is to assess the value of neural networks for classification of cancer and noncancer prostate cells. Gauss Markov Random Fields, Fourier entropy and wavelet average deviation features are calculated from 80 noncancer and 80 cancer prostate cell nuclei. For classification, artificial neural network techniques which are multilayer perceptron, radial basis function and learning vector quantization are used. Two methods are utilized for multilayer perceptron. First method has single hidden layer and between 3-15 nodes, second method has two hidden layer and each layer has between 3-15 nodes. Overall classification rate of 86.88% is achieved.
Abstract: Preparation of size controlled nano-particles of silver catalyst on carbon substrate from e-waste has been investigated. Chemical route was developed by extraction of the metals available in nitric acid followed by treatment with hydrofluoric acid. Silver metal particles deposited with an average size 4-10 nm. A stabilizer concentration of 10- 40 g/l was used. The average size of the prepared silver decreased with increase of the anode current density. Size uniformity of the silver nano-particles was improved distinctly at higher current density no more than 20mA... Grain size increased with EK time whereby aggregation of particles was observed after 6 h of reaction.. The chemical method involves adsorption of silver nitrate on the carbon substrate. Adsorbed silver ions were directly reduced to metal particles using hydrazine hydrate. Another alternative method is by treatment with ammonia followed by heating the carbon loaded-silver hydroxide at 980°C. The product was characterized with the help of XRD, XRF, ICP, SEM and TEM techniques.
Abstract: The “conveyor belt" as a product represents a
complex high performance component with a wide range of different
applications. Further development of these highly complex
components demands an integration of new technologies and new
enhanced materials. In this context nanostructured fillers appear to
have a more promising effect on the performance of the conveyor
belt composite than conventional micro-scaled fillers.
Within the project “DotTrans" nanostructured fillers, for example
silicon dioxide, are used to optimize performance parameters of
conveyor belt systems. The objective of the project includes
operating parameters like energy consumption or friction
characteristics as well as adaptive parameters like cut or wear
resistance.
Abstract: The current work focuses on rephrasing the harmful
effects of mercury that is being released from a number of sources.
Most of the sources are from the industrial waste water. Different
techniques of mercury removal have been discussed and a brief
comparison among these has been made. The experimental work has
been conducted for two most widely used methods of mercury
removal and comparison in terms of their efficiency has been made.
Abstract: It has been defined that the “network is the system".
This implies providing levels of service, reliability, predictability and
availability that are commensurate with or better than those that
individual computers provide today. To provide this requires
integrated network management for interconnected networks of
heterogeneous devices covering both the local campus. In this paper
we are addressing a framework to effectively deal with this issue. It
consists of components and interactions between them which are
required to perform the service fault management. A real-world
scenario is used to derive the requirements which have been applied
to the component identification. An analysis of existing frameworks
and approaches with respect to their applicability to the framework is
also carried out.
Abstract: This paper aimed to study the factors that relate to
working behavior of employees at Pakkred Municipality, Nonthaburi
Province. A questionnaire was utilized as the tool in collecting
information. Descriptive statistics included frequency, percentage,
mean and standard deviation. Independent- sample t- test, analysis of
variance and Pearson Correlation were also used. The findings of this
research revealed that the majority of the respondents were female,
between 25- 35 years old, married, with a Bachelor degree. The
average monthly salary of respondents was between 8,001- 12,000
Baht, and having about 4-7 years of working experience. Regarding
the overall working motivation factors, the findings showed that
interrelationship, respect, and acceptance were ranked as highly
important factors, whereas motivation, remunerations & welfare,
career growth, and working conditions were ranked as moderately
important factors. Also, overall working behavior was ranked as high.
The hypotheses testing revealed that different genders had a
different working behavior and had a different way of working as a
team, which was significant at the 0.05 confidence level, Moreover,
there was a difference among employees with different monthly
salary in working behavior, problem- solving and decision making,
which all were significant at the 0.05 confidence level. Employees
with different years of working experience were found to have work
working behavior both individual and as a team at the statistical
significance level of 0.01 and 0.05. The result of testing the
relationship between motivation in overall working revealed that
interrelationship, respect and acceptance from others, career growth,
and working conditions related to working behavior at a moderate
level, while motivation in performing duties and remunerations and
welfares related to working behavior towards the same direction at a
low level, with a statistical significance of 0.01.
Abstract: Creativity is often based on an unorthodox
recombination of knowledge; in fact: 80% of all innovations use
given knowledge and put it into a new combination. Cross-industry
innovations follow this way of thinking and bring together problems
and solution ideas from different industries. Therefore analogies and
search strategies have to be developed. Taking this path, the
questions where to search, what to search and how to search have to
be answered. Afterwards, the gathered information can be used
within a planned search process. Identified solution ideas have to be
assessed and analyzed in detail for the success promising adaption
planning.
Abstract: Face and facial expressions play essential roles in
interpersonal communication. Most of the current works on the facial
expression recognition attempt to recognize a small set of the
prototypic expressions such as happy, surprise, anger, sad, disgust
and fear. However the most of the human emotions are
communicated by changes in one or two of discrete features. In this
paper, we develop a facial expressions synthesis system, based on the
facial characteristic points (FCP's) tracking in the frontal image
sequences. Selected FCP's are automatically tracked using a crosscorrelation
based optical flow. The proposed synthesis system uses a
simple deformable facial features model with a few set of control
points that can be tracked in original facial image sequences.