Abstract: The purpose of the present study is to determine the level of reading habit of future classroom teachers, to discuss the obtained results according to their socio-demographic features and to define the factors which are influential on taking up reading in the context of future teachers experiences. The target population of the study consists of the fourth grade students at 62 faculties of education, department of classroom teaching from Turkish state universities. The sampling of the study consists of the fourth grade students from seven faculties of education, department of classroom teaching from each region. In the study, in the first and the second aspects, there will be a questionnaire to be developed concerning the measurement of future teachers level of reading habits and their socio-demographic features. The questionnaire was applied to all the students in the sample.
Abstract: The present work deals with the stabilisation of
organic clay using hydrated lime. Artificial organic clays were
prepared by adding kaolin and different humic acid contents. Results
given by physical testing show that the presence of humic acid has a
drawback effect on the untreated organic clay. The decrease in
specific gravity value was accompanied by a decrease in dry density
and plasticity of clay at higher humic acid contents. Significant
increase in shear strength at 7 days of curing period is observed in the
lime-treated samples up to 5% lime content. However shear strength
of lime-treated organic clay decreases at longer curing periods. The
results given by laboratory testing is further verified by
microstructure analysis. Based on the results obtained in this study, it
can be concluded that the presence of more than 1.5% humic acid
reduces significantly the efficiency of lime stabilization in organic
clays.
Abstract: The radiative exchange method is introduced as a
numerical method for the simulation of radiative heat transfer in an
absorbing, emitting and isotropically scattering media. In this
method, the integro-differential radiative balance equation is solved
by using a new introduced concept for the exchange factor. Even
though the radiative source term is calculated in a mesh structure that
is coarser than the structure used in computational fluid dynamics,
calculating the exchange factor between different coarse elements by
using differential integration elements makes the result of the method
close to that of integro-differential radiative equation. A set of
equations for calculating exchange factors in two and threedimensional
Cartesian coordinate system is presented, and the
method is used in the simulation of radiative heat transfer in twodimensional
rectangular case and a three-dimensional simple cube.
The result of using this method in simulating different cases is
verified by comparing them with those of using other numerical
radiative models.
Abstract: In this paper a procedure for the split-pipe design of looped water distribution network based on the use of simulated annealing is proposed. Simulated annealing is a heuristic-based search algorithm, motivated by an analogy of physical annealing in solids. It is capable for solving the combinatorial optimization problem. In contrast to the split-pipe design that is derived from a continuous diameter design that has been implemented in conventional optimization techniques, the split-pipe design proposed in this paper is derived from a discrete diameter design where a set of pipe diameters is chosen directly from a specified set of commercial pipes. The optimality and feasibility of the solutions are found to be guaranteed by using the proposed method. The performance of the proposed procedure is demonstrated through solving the three well-known problems of water distribution network taken from the literature. Simulated annealing provides very promising solutions and the lowest-cost solutions are found for all of these test problems. The results obtained from these applications show that simulated annealing is able to handle a combinatorial optimization problem of the least cost design of water distribution network. The technique can be considered as an alternative tool for similar areas of research. Further applications and improvements of the technique are expected as well.
Abstract: This paper addresses one important aspect of
combustion system analysis, the spray evaporation and
dispersion modeling. In this study we assume an empty
cylinder which is as a simulator for a ramjet engine and the
cylinder has been studied by cold flow. Four nozzles have the
duties of injection which are located in the entrance of
cylinder. The air flow comes into the cylinder from one side
and injection operation will be done. By changing injection
velocity and entrance air flow velocity, we have studied
droplet sizing and efficient mass fraction of fuel vapor near
and at the exit area. We named the mass of fuel vapor inside
the flammability limit as the efficient mass fraction. Further,
we decreased the initial temperature of fuel droplets and we
have repeated the investigating again. To fulfill the calculation
we used a modified version of KIVA-3V.
Abstract: The principal objective of a water treatment plant is to
produce water that satisfies a set of drinking water quality standards
at a reasonable price to the consumers. The gravel-bed flocculator
provide a simple and inexpensive design for flocculation in small
water treatment plants (less than 5000 m3/day capacity). The packed
bed of gravel provides ideal conditions for the formation of compact
settleable flocs because of continuous recontact provided by the
sinuous flow of water through the interstices formed by the gravel.
The field data which were obtained from the operation of the
water supply treatment unit cover the physical, chemical and
biological water qualities of the raw and settled water as obtained by
the operation of the treatment unit. The experiments were carried out
with the aim of assessing the efficiency of the gravel filter in
removing the turbidity, pathogenic bacteria, from the raw water. The
water treatment plant, which was constructed for the treatment of
river water, was in principle a rapid sand filter.
The results show that the average value of the turbidity level of
the settled water was 4.83 NTU with a standard deviation of turbidity
2.893 NTU. This indicated that the removal efficiency of the
sedimentation tank (gravel filter) was about 67.8 %. for pH values
fluctuated between 7.75 and 8.15, indicating the alkaline nature of
the raw water of the river Shatt Al-Hilla, as expected. Raw water pH
is depressed slightly following alum coagulation. The pH of the
settled water ranged from 7.75 to a maximum of 8.05.
The bacteriological tests which were carried out on the water
samples were: total coliform test, E-coli test, and the plate count test.
In each test the procedure used was as outlined in the Standard
Methods for the Examination of Water and Wastewater (APHA,
AWWA, and WPCF, 1985). The gravel filter exhibit a low
performance in removing bacterial load. The percentage bacterial
removal, which is maximum for total plate count (19%) and
minimum for total coliform (16.82%).
Abstract: A 7-step method (with 25 sub-steps) to assess risk of
air pollutants is introduced. These steps are: pre-considerations,
sampling, statistical analysis, exposure matrix and likelihood, doseresponse
matrix and likelihood, total risk evaluation, and discussion
of findings. All mentioned words and expressions are wellunderstood;
however, almost all steps have been modified, improved,
and coupled in such a way that a comprehensive method has been
prepared. Accordingly, the SADRA (Statistical Analysis-Driven Risk
Assessment) emphasizes extensive and ongoing application of
analytical statistics in traditional risk assessment models. A Sulfur
Dioxide case study validates the claim and provides a good
illustration for this method.
Abstract: Social interest and demand on Home-Network has
been increasing greatly. Although various services are being
introduced to respond to such demands, they can cause serious
security problems when linked to the open network such as Internet.
This paper reviews the security requirements to protect the service
users with assumption that the Home-Network environment is
connected to Internet and then proposes the security model based on
the requirement. The proposed security model can satisfy most of the
requirements and further can be dynamically applied to the future
ubiquitous Home-Networks.
Abstract: The effect of chemical treatment in CdCl2 and thermal
annealing in 400°C, on the defect structures of potentially useful
ZnS\CdS solar cell thin films deposited onto quartz substrate and
prepared by vacuum deposition method was studied using the
Thermoluminesence (TL) techniques. A series of electron and hole
traps are found in the various deposited samples studied. After
annealing, however, it was observed that the intensity and activation
energy of TL signal increases with loss of the low temperature
electron traps.
Abstract: The present study explains the effect of aggregate
gradation on moisture damage in bituminous mixes. Three types of
aggregate gradation and two types of binder; VG-30 and Polymer
modified bitumen (PMB-40) are used. Moisture susceptibility tests
like retained stability and tensile strength ratio (TSR) and static creep
test are conducted on Marshall specimens. The creep test was also
conducted for conditioned and unconditioned specimens to observe
the effect of moisture on creep behaviour. The results indicate that
Marshall stability value is higher in PMB-40 mix than VG-30 mixes.
Moisture susceptibility of PMB-40 mixes is low when compared with
mix using VG-30. The reduction in retained stability, and indirect
tensile strength and increase in creep are evaluated for finer, coarser
and normal gradation of aggregate to observe the effect of gradation
on moisture susceptibility of mixes. The retained stability is least
affected when compared with other moisture susceptibility
parameters
Abstract: This paper presents the experimental results of
discharge current phenomena on various humidity, temperature,
pressure and pollutant conditions of epoxy resin specimen. The
leakage distance of specimen was 3 cm, that it was supplied by high
voltage. The polluted condition was given with NaCl artificial
pollutant. The conducted measurements were discharge current and
applied voltage. The specimen was put in a hermetically sealed
chamber, and the current waveforms were analyzed with FFT.
The result indicated that on discharge condition, the fifth
harmonics still had dominant, rather than third one. The third
harmonics tent to be appeared on low pressure heavily polluted
condition, and followed by high humidity heavily polluted condition.
On the heavily polluted specimen, the peaks discharge current points
would be high and more frequent. Nevertheless, the specimen still
had capacitive property. Besides that, usually discharge current
points were more frequent. The influence of low pressure was still
dominant to be easier to discharge. The non-linear property would be
appear explicitly on low pressure and heavily polluted condition.
Abstract: This paper deals with the development and obstacles of
Korean women-s political participation in recent years. Since the year
1948 after the declaration of a modern state, Korea has tried to
establish the democracy but still in the field of women-s political
participation it meets a lot of problems such as women-s political
consciousness, male dominated political culture and institutional
constraints. After the introduction of quota system in the list of
political party, women-s political participation began to change its
configuration. More women candidates have willingly presented at
elections.
Abstract: Safety of bus journey is a fundamental concern. Risk of injuries and fatalities is severe when bus superstructure fails during rollover accident. Adequate design and sufficient strength of bus superstructure can reduce the number of injuries and fatalities. This paper deals with structural analysis of bus superstructure undergoes rollover event. Several value of mass will be varied in multiple simulations. The purpose of this work is to analyze structural response of bus superstructure in terms of deformation, stress and strain under several loading and constraining conditions. A complete bus superstructure with forty four passenger-s capability was developed using finite element analysis software. Simulations have been conducted to observe the effect of total mass of bus on the strength of superstructure. These simulations are following United Nation Economic Commission of Europe regulation 66 which focuses on strength of large vehicle superstructure. Validation process had been done using simple box model experiment and results obtained are comparing with simulation results. Inputs data from validation process had been used in full scale simulation. Analyses suggested that, the failure of bus superstructure during rollover situation is basically dependent on the total mass of bus and on the strength of bus superstructure.
Abstract: In this study, a reformer model simulation to use
refinery (Farashband refinery, Iran) waste natural gas. In the
petroleum and allied sectors where natural gas is being encountered
(in form of associated gas) without prior preparation for its positive
use, its combustion (which takes place in flares, an equipment through
which they are being disposed) has become a great problem because
of its associated environmental problems in form of gaseous emission.
The proposed model is used to product syngas from waste natural gas.
A detailed steady model described by a set of ordinary differential and
algebraic equations was developed to predict the behavior of the
overall process. The proposed steady reactor model was validated
against process data of a reformer synthesis plant recorded and a good
agreement was achieved. H2/CO ratio has important effect on Fischer-
Tropsch synthesis reactor product and we try to achieve this parameter
with best designing reformer reactor. We study different kind of
reformer reactors and then select auto thermal reforming process of
natural gas in a fixed bed reformer that adjustment H2/CO ratio with
CO2 and H2O injection. Finally a strategy was proposed for prevention
of extra natural gas to atmosphere.
Abstract: With the growth of electricity generation from gas
energy gas pipeline reliability can substantially impact the electric
generation. A physical disruption to pipeline or to a compressor
station can interrupt the flow of gas or reduce the pressure and lead
to loss of multiple gas-fired electric generators, which could
dramatically reduce the supplied power and threaten the power
system security. Gas pressure drops during peak loading time on
pipeline system, is a common problem in network with no enough
transportation capacity which limits gas transportation and causes
many problem for thermal domain power systems in supplying their
demand. For a feasible generation scheduling planning in networks
with no sufficient gas transportation capacity, it is required to
consider gas pipeline constraints in solving the optimization problem
and evaluate the impacts of gas consumption in power plants on gas
pipelines operating condition. This paper studies about operating of
gas fired power plants in critical conditions when the demand of gas
and electricity peak together. An integrated model of gas and electric
model is used to consider the gas pipeline constraints in the economic
dispatch problem of gas-fueled thermal generator units.
Abstract: This paper presents the development of adaptive
distance relay for protection of parallel transmission line with mutual
coupling. The proposed adaptive relay, automatically adjusts its
operation based on the acquisition of the data from distance relay of
adjacent line and status of adjacent line from line circuit breaker IED
(Intelligent Electronic Device). The zero sequence current of the
adjacent parallel transmission line is used to compute zero sequence
current ratio and the mutual coupling effect is fully compensated.
The relay adapts to changing circumstances, like failure in
communication from other relays and non - availability of adjacent
transmission line. The performance of the proposed adaptive relay is
tested using steady state and dynamic test procedures. The fault
transients are obtained by simulating a realistic parallel transmission
line system with mutual coupling effect in PSCAD. The evaluation
test results show the efficacy of adaptive distance relay over the
conventional distance relay.
Abstract: Wind power is among the most actively developing distributed generation (DG) technology. Majority of the wind power based DG technologies employ wind turbine induction generators (WTIG) instead of synchronous generators, for the technical advantages like: reduced size, increased robustness, lower cost, and increased electromechanical damping. However, dynamic changes of wind speed make the amount of active/reactive power injected/drawn to a WTIG embedded distribution network highly variable. This paper analyzes the effect of wind speed changes on the active and reactive power penetration to the wind energy embedded distribution network. Four types of wind speed changes namely; constant, linear change, gust change and random change of wind speed are considered in the analysis. The study is carried out by three-phase, non-linear, dynamic simulation of distribution system component models. Results obtained from the investigation are presented and discussed.
Abstract: Stick models are widely used in studying the
behaviour of straight as well as skew bridges and viaducts subjected
to earthquakes while carrying out preliminary studies. The
application of such models to highly curved bridges continues to
pose challenging problems. A viaduct proposed in the foothills of the
Himalayas in Northern India is chosen for the study. It is having 8
simply supported spans @ 30 m c/c. It is doubly curved in horizontal
plane with 20 m radius. It is inclined in vertical plane as well. The
superstructure consists of a box section. Three models have been
used: a conventional stick model, an improved stick model and a 3D
finite element model. The improved stick model is employed by
making use of body constraints in order to study its capabilities. The
first 8 frequencies are about 9.71% away in the latter two models.
Later the difference increases to 80% in 50th mode. The viaduct was
subjected to all three components of the El Centro earthquake of May
1940. The numerical integration was carried out using the Hilber-
Hughes-Taylor method as implemented in SAP2000. Axial forces
and moments in the bridge piers as well as lateral displacements at
the bearing levels are compared for the three models. The maximum
difference in the axial forces and bending moments and
displacements vary by 25% between the improved and finite element
model. Whereas, the maximum difference in the axial forces,
moments, and displacements in various sections vary by 35%
between the improved stick model and equivalent straight stick
model. The difference for torsional moment was as high as 75%. It is
concluded that the stick model with body constraints to model the
bearings and expansion joints is not desirable in very sharp S curved
viaducts even for preliminary analysis. This model can be used only
to determine first 10 frequency and mode shapes but not for member
forces. A 3D finite element analysis must be carried out for
meaningful results.
Abstract: This research paper presents the CFD analysis of
oscillating airfoil during pitch cycle. Unsteady subsonic flow is
simulated for pitching airfoil at Mach number 0.283 and Reynolds
number 3.45 millions. Turbulent effects are also considered for this
study by using K-ω SST turbulent model. Two-dimensional unsteady
compressible Navier-Stokes code including two-equation turbulence
model and PISO pressure velocity coupling is used. Pressure based
implicit solver with first order implicit unsteady formulation is used.
The simulated pitch cycle results are compared with the available
experimental data. The results have a good agreement with the
experimental data. Aerodynamic characteristics during pitch cycles
have been studied and validated.
Abstract: Commercial hydroxyapatite (HA) was reinforced by
adding 2, 5, and 10 wt % of 28.5%CaO-28.5%P2O5-38%Na2 O-
5%CaF2 based glass and then sintered. Although HA shows good
biocompatibility with the human body, its applications are limited to
non load-bearing areas and coatings due to its poor mechanical
properties. These mechanical properties can be improved
substantially with addition of glass ceramics by sintering. In this
study, the effects of sintering hydroxyapatite with above specified
phosphate glass additions are quantified. Each composition was
sintered over a range of temperatures. Scanning electron microscopy
and x-ray diffraction were used to characterize the microstructure and
phases of the composites. The density, microhardness, and
compressive strength were measured using Archimedes Principle,
Vickers Microhardness Tester (at 0.98 N), and Instron Universal
Testing Machine (cross speed of 0.5 mm/min) respectively. These
results were used to indicate which composition provided suitable
material for use in hard tissue replacement. Composites containing 10
wt % glass additions formed dense HA/TCP (tricalcium phosphate)
composite materials possessing good compressive strength and
hardness than HA. In-vitro bioactivity was assessed by evaluating
changes in pH and Ca2+ ion concentration of SBF-simulated body
fluid on immersion of these composites in it for two weeks.