Abstract: This paper presents results of measurements campaign
carried out at a carrier frequency of 24GHz with the help of TPLINK
router in indoor line-of-sight (LOS) scenarios. Firstly, the
radio wave propagation strategies are analyzed in some rooms with
router of point to point Ad hoc network. Then floor attenuation is
defined for 3 floors in experimental region. The free space model and
dual slope models are modified by considering the influence of
corridor conditions on each floor. Using these models, indoor signal
attenuation can be estimated in modeling of indoor radio wave
propagation. These results and modified models can also be used in
planning the networks of future personal communications services.
Abstract: This paper presents a subjective job scheduler based
on a 3-layer Backpropagation Neural Network (BPNN) and a greedy
alignment procedure in order formulates a real-life situation. The
BPNN estimates critical values of jobs based on the given subjective
criteria. The scheduler is formulated in such a way that, at each time
period, the most critical job is selected from the job queue and is
transferred into a single machine before the next periodic job arrives.
If the selected job is one of the oldest jobs in the queue and its
deadline is less than that of the arrival time of the current job, then
there is an update of the deadline of the job is assigned in order to
prevent the critical job from its elimination. The proposed
satisfiability criteria indicates that the satisfaction of the scheduler
with respect to performance of the BPNN, validity of the jobs and the
feasibility of the scheduler.
Abstract: In this paper, a direct torque control - space vector
modulation (DTC-SVM) scheme is presented for a six-phase speed
and voltage sensorless induction motor (IM) drive. The decoupled
torque and stator flux control is achieved based on IM stator flux field orientation. The rotor speed is detected by on-line estimating of
the rotor angular slip speed and stator vector flux speed. In addition, a simple method is introduced to estimate the stator resistance.
Moreover in this control scheme the voltage sensors are eliminated
and actual motor phase voltages are approximated by using PWM
inverter switching times and the dc link voltage. Finally, some simulation and experimental results are presented to verify the
effectiveness and capability of the proposed control scheme.
Abstract: Accurate demand forecasting is one of the most key
issues in inventory management of spare parts. The problem of
modeling future consumption becomes especially difficult for lumpy
patterns, which characterized by intervals in which there is no
demand and, periods with actual demand occurrences with large
variation in demand levels. However, many of the forecasting
methods may perform poorly when demand for an item is lumpy.
In this study based on the characteristic of lumpy demand patterns
of spare parts a hybrid forecasting approach has been developed,
which use a multi-layered perceptron neural network and a
traditional recursive method for forecasting future demands. In the
described approach the multi-layered perceptron are adapted to
forecast occurrences of non-zero demands, and then a conventional
recursive method is used to estimate the quantity of non-zero
demands. In order to evaluate the performance of the proposed
approach, their forecasts were compared to those obtained by using
Syntetos & Boylan approximation, recently employed multi-layered
perceptron neural network, generalized regression neural network
and elman recurrent neural network in this area. The models were
applied to forecast future demand of spare parts of Arak
Petrochemical Company in Iran, using 30 types of real data sets. The
results indicate that the forecasts obtained by using our proposed
mode are superior to those obtained by using other methods.
Abstract: We present an Electronic Nose (ENose), which is
aimed at identifying the presence of one out of two gases, possibly
detecting the presence of a mixture of the two. Estimation of the
concentrations of the components is also performed for a volatile
organic compound (VOC) constituted by methanol and acetone, for
the ranges 40-400 and 22-220 ppm (parts-per-million), respectively.
Our system contains 8 sensors, 5 of them being gas sensors (of the
class TGS from FIGARO USA, INC., whose sensing element is a tin
dioxide (SnO2) semiconductor), the remaining being a temperature
sensor (LM35 from National Semiconductor Corporation), a
humidity sensor (HIH–3610 from Honeywell), and a pressure sensor
(XFAM from Fujikura Ltd.).
Our integrated hardware–software system uses some machine
learning principles and least square regression principle to identify at
first a new gas sample, or a mixture, and then to estimate the
concentrations. In particular we adopt a training model using the
Support Vector Machine (SVM) approach with linear kernel to teach
the system how discriminate among different gases. Then we apply
another training model using the least square regression, to predict
the concentrations.
The experimental results demonstrate that the proposed
multiclassification and regression scheme is effective in the
identification of the tested VOCs of methanol and acetone with
96.61% correctness. The concentration prediction is obtained with
0.979 and 0.964 correlation coefficient for the predicted versus real
concentrations of methanol and acetone, respectively.
Abstract: In this article, models based on quantitative analysis,
physical geometry and regression analysis are established, by using
analytic hierarchy process analysis, fuzzy cluster analysis, fuzzy
photographic and data fitting. The reasons of various leaf shapes
among different species and the differences between the leaf shapes on
same tree have been solved by using software, such as Eviews, VB and
Matlab. We also successfully estimate the leaf mass of a tree and the
correlation with the tree profile.
Abstract: Com Poisson distribution is capable of modeling the count responses irrespective of their mean variance relation and the parameters of this distribution when fitted to a simple cross sectional data can be efficiently estimated using maximum likelihood (ML) method. In the regression setup, however, ML estimation of the parameters of the Com Poisson based generalized linear model is computationally intensive. In this paper, we propose to use quasilikelihood (QL) approach to estimate the effect of the covariates on the Com Poisson counts and investigate the performance of this method with respect to the ML method. QL estimates are consistent and almost as efficient as ML estimates. The simulation studies show that the efficiency loss in the estimation of all the parameters using QL approach as compared to ML approach is quite negligible, whereas QL approach is lesser involving than ML approach.
Abstract: Counting people from a video stream in a noisy environment is a challenging task. This project aims at developing a counting system for transport vehicles, integrated in a video surveillance product. This article presents a method for the detection and tracking of multiple faces in a video by using a model of first and second order local moments. An iterative process is used to estimate the position and shape of multiple faces in images, and to track them. the trajectories are then processed to count people entering and leaving the vehicle.
Abstract: Run-offs are considered as important hydrological factors in feasibility studies of river engineering and irrigation-related projects under arid and semi-arid condition. Flood control is one of the crucial factor, the management of which while mitigates its destructive consequences, abstracts considerable volume of renewable water resources. The methodology applied here was based on Mizumura, which applied a mathematical model for simple tank to simulate the rainfall-run-off process in a particular water basin using the data from the observational hydrograph. The model was applied in the Dez River water basin adjacent to Greater Dezful region, Iran in order to simulate and estimate the floods. Results indicated that the calculated hydrographs using the simple tank method, SCS-CN model and the observation hydrographs had a close proximity. It was also found that on average the flood time and discharge peaks in the simple tank were closer to the observational data than the CN method. On the other hand, the calculated flood volume in the CN model was significantly closer to the observational data than the simple tank model.
Abstract: Compaction testing methods allow at-speed detecting
of errors while possessing low cost of implementation. Owing to this
distinctive feature, compaction methods have been widely used for
built-in testing, as well as external testing. In the latter case, the
bandwidth requirements to the automated test equipment employed
are relaxed which reduces the overall cost of testing. Concurrent
compaction testing methods use operational signals to detect
misbehavior of the device under test and do not require input test
stimuli. These methods have been employed for digital systems only.
In the present work, we extend the use of compaction methods for
concurrent testing of analog-to-digital converters. We estimate
tolerance bounds for the result of compaction and evaluate the
aliasing rate.
Abstract: In this paper, the phase control antenna array synthesis
is presented. The problem is formulated as a constrained optimization
problem that imposes nulls with prescribed level while maintaining
the sidelobe at a prescribed level. For efficient use of the algorithm
memory, compared to the well known Particle Swarm Optimization
(PSO), the Accelerated Particle Swarm Optimization (APSO) is used
to estimate the phase parameters of the synthesized array. The
objective function is formed using a main objective and set of
constraints with penalty factors that measure the violation of each
feasible solution in the search space to each constraint. In this case
the obtained feasible solution is guaranteed to satisfy all the
constraints. Simulation results have shown significant performance
increases and a decreased randomness in the parameter search space
compared to a single objective conventional particle swarm
optimization.
Abstract: The IEEE802.16 standard which has emerged as
Broadband Wireless Access (BWA) technology, promises to deliver
high data rate over large areas to a large number of subscribers in the
near future. This paper analyze the effect of overheads over capacity
of downlink (DL) of orthogonal frequency division multiple access
(OFDMA)–based on the IEEE802.16e mobile WiMAX system with
and without overheads. The analysis focuses in particular on the
impact of Adaptive Modulation and Coding (AMC) as well as
deriving an algorithm to determine the maximum numbers of
subscribers that each specific WiMAX sector may support. An
analytical study of the WiMAX propagation channel by using Cost-
231 Hata Model is presented. Numerical results and discussion
estimated by using Matlab to simulate the algorithm for different
multi-users parameters.
Abstract: Today, incorrect use of lands and land use changes,
excessive grazing, no suitable using of agricultural farms, plowing on
steep slopes, road construct, building construct, mine excavation etc
have been caused increasing of soil erosion and sediment yield. For
erosion and sediment estimation one can use statistical and empirical
methods. This needs to identify land unit map and the map of
effective factors. However, these empirical methods are usually time
consuming and do not give accurate estimation of erosion. In this
study, we applied GIS techniques to estimate erosion and sediment of
Menderjan watershed at upstream Zayandehrud river in center of
Iran. Erosion faces at each land unit were defined on the basis of land
use, geology and land unit map using GIS. The UTM coordinates of
each erosion type that showed more erosion amounts such as rills and
gullies were inserted in GIS using GPS data. The frequency of
erosion indicators at each land unit, land use and their sediment yield
of these indices were calculated. Also using tendency analysis of
sediment yield changes in watershed outlet (Menderjan hydrometric
gauge station), was calculated related parameters and estimation
errors. The results of this study according to implemented watershed
management projects can be used for more rapid and more accurate
estimation of erosion than traditional methods. These results can also
be used for regional erosion assessment and can be used for remote
sensing image processing.
Abstract: A reliable estimate of the average bond stress within
the anchorage of steel reinforcing bars in tension is critically
important for the design of reinforced concrete member. This paper
describes part of a recently completed experimental research program
in the Centre for Infrastructure Engineering and Safety (CIES) at the
University of New South Wales, Sydney, Australia aimed at
assessing the effects of different factors on the anchorage
requirements of modern high strength steel reinforcing bars. The
study found that an increase in the anchorage length and bar diameter
generally leads to a reduction of the average ultimate bond stress. By
the extension of a well established analytical model of bond and
anchorage, it is shown here that the differences in the average
ultimate bond stress for different anchorage lengths is associated with
the variable degree of plastic deformation in the tensile zone of the
concrete surrounding the bar.
Abstract: Despite the availability of natural disaster related time series data for last 110 years, there is no forecasting tool available to humanitarian relief organizations to determine forecasts for emergency logistics planning. This study develops a forecasting tool based on identifying probability distributions. The estimates of the parameters are used to calculate natural disaster forecasts. Further, the determination of aggregate forecasts leads to efficient pre-disaster planning. Based on the research findings, the relief agencies can optimize the various resources allocation in emergency logistics planning.
Abstract: The modeling of water transfer in the unsaturated zone
uses techniques and methods of the soil physics to solve the
Richards-s equation. However, there is a disaccord between the size
of the measurements provided by the soil physics and the size of the
fields of hydrological modeling problem, to which is added the
strong spatial variability of soil hydraulic properties. The objective of
this work was to develop a methodology to estimate the
hydrodynamic parameters for modeling water transfers at different
hydrological scales in the soil-plant atmosphere systems.
Abstract: We address the problem of joint beamforming and multipath channel parameters estimation in Wideband Code Division Multiple Access (WCDMA) communication systems that employ Multiple-Access Interference (MAI) suppression techniques in the uplink (from mobile to base station). Most of the existing schemes rely on time multiplex a training sequence with the user data. In WCDMA, the channel parameters can also be estimated from a code multiplexed common pilot channel (CPICH) that could be corrupted by strong interference resulting in a bad estimate. In this paper, we present new methods to combine interference suppression together with channel estimation when using multiple receiving antennas by using adaptive signal processing techniques. Computer simulation is used to compare between the proposed methods and the existing conventional estimation techniques.
Abstract: The wisest economic decision of United States in the
20th century was establishing the favorable international monetary
system, and capturing the leadership position in it. This decision gave
economic hegemony to the US for the next more than 7 decades. The
continuation of this hegemony till the next decade seems difficult as
the US economy is under continuous streams of recessions since
2007. On the other hand, Chinese economy is progressing with a
very fast speed and is estimated to pass the US economy till 2025, in
various aspects. Will the US be able to continue its leadership in the
IMS? Will China replace US in the international monetary system?
The answers to these questions have been explored by comparing the
economic competitiveness of US and China, with respect to each
other. The paper concludes that the change in global economic
environment will compel US to share the leadership of international
monetary system with China. This sharing will solve most problems
of the current IMS, but will also birth some new problems.
Abstract: Presented herein is an assessment of current nonlinear
static procedures (NSPs) for seismic evaluation of bucklingrestrained
braced frames (BRBFs) which have become a favorable
lateral-force resisting system for earthquake resistant buildings. The
bias and accuracy of modal, improved modal pushover analysis
(MPA, IMPA) and mass proportional pushover (MPP) procedures
are comparatively investigated when they are applied to BRBF
buildings subjected to two sets of strong ground motions. The
assessment is based on a comparison of seismic displacement
demands such as target roof displacements, peak floor/roof
displacements and inter-story drifts. The NSP estimates are compared
to 'exact' results from nonlinear response history analysis (NLRHA).
The response statistics presented show that the MPP
procedure tends to significantly overestimate seismic demands of
lower stories of tall buildings considered in this study while MPA
and IMPA procedures provide reasonably accurate results in
estimating maximum inter-story drift over all stories of studied BRBF
systems.
Abstract: Apparel product development is an important stage in the life cycle of a product. Shortening this stage will help to reduce the costs of a garment. The aim of this study is to examine the production parameters in knitwear apparel companies by defining the unit costs, and developing a software to calculate the unit costs of garments and make the cost estimates. In this study, with the help of a questionnaire, different companies- systems of unit cost estimating and cost calculating were tried to be analyzed. Within the scope of the questionnaire, the importance of cost estimating process for apparel companies and the expectations from a new cost estimating program were investigated. According to the results of the questionnaire, it was seen that the majority of companies which participated to the questionnaire use manual cost calculating methods or simple Microsoft Excel spreadsheets to make cost estimates. Furthermore, it was discovered that many companies meet with difficulties in archiving the cost data for future use and as a solution to that problem, it is thought that prior to making a cost estimate, sub units of garment costs which are fabric, accessory and the labor costs should be analyzed and added to the database of the programme beforehand. Another specification of the cost estimating unit prepared in this study is that the programme was designed to consist of two main units, one of which makes the product specification and the other makes the cost calculation. The programme is prepared as a web-based application in order that the supplier, the manufacturer and the customer can have the opportunity to communicate through the same platform.