Abstract: The dynamics of Min proteins plays a center role in
accurate cell division. Although the nucleoids may presumably play
an important role in prokaryotic cell division, there is a lack of
models to account for its participation. In this work, we apply the
lattice Boltzmann method to investigate protein oscillation based on a
mesoscopic model that takes into account the nucleoid-s role. We
found that our numerical results are in reasonably good agreement
with the previous experimental results On comparing with the other
computational models without the presence of nucleoids, the
highlight of our finding is that the local densities of MinD and MinE
on the cytoplasmic membrane increases, especially along the cell
width, when the size of the obstacle increases, leading to a more
distinct cap-like structure at the poles. This feature indicated the
realistic pattern and reflected the combination of Min protein
dynamics and nucleoid-s role.
Abstract: Properties of cement pastes with fine-ground ceramics
used as an alternative binder replacing Portland cement up to 20% of
its mass are investigated. At first, the particle size distribution of
cement and fine-ground ceramics is measured using laser analyser.
Then, the material properties are studied in the early hardening
period up to 28 days. The hydration process of studied materials is
monitored by electrical conductivity measurement using TDR
sensors. The changes of materials- structures within the hardening are
observed using pore size distribution measurement. The compressive
strength measurements are done as well. Experimental results show
that the replacement of Portland cement by fine-ground ceramics in
the amount of up to 20% by mass is acceptable solution from the
mechanical point of view. One can also assume similar physical
properties of designed materials to the reference material with only
Portland cement as binder.
Abstract: Since the driving speed and control accuracy of
commercial optical disk are increasing significantly, it needs an
efficient controller to monitor the track seeking and following
operations of the servo system for achieving the desired data
extracting response. The nonlinear behaviors of the actuator and servo
system of the optical disk drive will influence the laser spot
positioning. Here, the model-free fuzzy control scheme is employed to
design the track seeking servo controller for a d.c. motor driving
optical disk drive system. In addition, the sliding model control
strategy is introduced into the fuzzy control structure to construct a
1-D adaptive fuzzy rule intelligent controller for simplifying the
implementation problem and improving the control performance. The
experimental results show that the steady state error of the track
seeking by using this fuzzy controller can maintain within the track
width (1.6 μm ). It can be used in the track seeking and track
following servo control operations.
Abstract: This research focus on developing a new segmentation method for improving forecasting model which is call trend based segmentation method (TBSM). Generally, the piece-wise linear representation (PLR) can finds some of pair of trading points is well for time series data, but in the complicated stock environment it is not well for stock forecasting because of the stock has more trends of trading. If we consider the trends of trading in stock price for the trading signal which it will improve the precision of forecasting model. Therefore, a TBSM with SVR model used to detect the trading points for various stocks of Taiwanese and America under different trend tendencies. The experimental results show our trading system is more profitable and can be implemented in real time of stock market
Abstract: The use of additions in cement in manufacturing,
mortar and concrete offers economic and ecological advantages. Cements with additions such as limestone, slag and natural
pouzzolana are produced in cement factories in Algeria. Several studies analyzed the effect of these additions on the physical and
mechanical properties as well as the durability of concrete. However,
few studies were conducted on the effect of local metakaolin on
mechanical properties and durability of concrete. The main purpose
of this paper is to analyze the performance of mortar and concrete with local metakaolin. The preparation of the metakaolin was carried
out by calcination of kaolin at a temperature of 850 °C for a period of 3 hours. The experimental results have shown that the rates of
substitutions of 10 and 15% metakaolin increases the compressive
strength and flexural strength at both early age and long term. The durability and the permeability were also improved by reducing the
coefficient of sorptivity.
Abstract: in dissimilar material joints, failure often occurs
along the interface between two materials due to stress singularity.
Stress distribution and its concentration depend on materials and
geometry of the junction. Inhomogenity of stress distribution at the
interface of junction of two materials with different elastic modules
and stress concentration in this zone are the main factors resulting in
rupture of the junction. Effect of joining angle in the interface of
aluminum-polycarbonate will be discussed in this paper. Computer
simulation and finite element analysis by ABAQUS showed that
convex interfacial joint leads to stress reduction at junction corners in
compare with straight joint. This finding is confirmed by photoelastic
experimental results.
Abstract: Magnesium alloys have gained increased attention in recent years in automotive, electronics, and medical industry. This because of magnesium alloys have better properties than aluminum alloys and steels in respects of their low density and high strength to weight ratio. However, the main problems of magnesium alloy welding are the crack formation and the appearance of porosity during the solidification. This paper proposes a unique technique to weld two thin sheets of AZ31B magnesium alloy using a paste containing Ag nanoparticles. The paste containing Ag nanoparticles of 5 nm in average diameter and an organic solvent was used to coat the surface of AZ31B thin sheet. The coated sheet was heated at 100 °C for 60 s to evaporate the solvent. The dried sheet was set as a lower AZ31B sheet on the jig, and then lap fillet welding was carried out by using a pulsed Nd:YAG laser in a closed box filled with argon gas. The characteristics of the microstructure and the corrosion behavior of the joints were analyzed by opticalmicroscopy (OM), energy dispersive spectrometry (EDS), electron probe micro-analyzer (EPMA), scanning electron microscopy (SEM), and immersion corrosion test. The experimental results show that the wrought AZ31B magnesium alloy can be joined successfully using Ag nanoparticles. Ag nanoparticles insert promote grain refinement, narrower the HAZ width and wider bond width compared to weld without and insert. Corrosion rate of welded AZ31B with Ag nanoparticles reduced up to 44 % compared to base metal. The improvement of corrosion resistance of welded AZ31B with Ag nanoparticles due to finer grains and large grain boundaries area which consist of high Al content. β-phase Mg17Al12 could serve as effective barrier and suppressed further propagation of corrosion. Furthermore, Ag distribution in fusion zone provide much more finer grains and may stabilize the magnesium solid solution making it less soluble or less anodic in aqueous
Abstract: For the communication between human and computer
in an interactive computing environment, the gesture recognition is
studied vigorously. Therefore, a lot of studies have proposed efficient
methods about the recognition algorithm using 2D camera captured
images. However, there is a limitation to these methods, such as the
extracted features cannot fully represent the object in real world.
Although many studies used 3D features instead of 2D features for
more accurate gesture recognition, the problem, such as the processing
time to generate 3D objects, is still unsolved in related researches.
Therefore we propose a method to extract the 3D features combined
with the 3D object reconstruction. This method uses the modified
GPU-based visual hull generation algorithm which disables unnecessary
processes, such as the texture calculation to generate three kinds
of 3D projection maps as the 3D feature: a nearest boundary, a farthest
boundary, and a thickness of the object projected on the base-plane. In
the section of experimental results, we present results of proposed
method on eight human postures: T shape, both hands up, right hand
up, left hand up, hands front, stand, sit and bend, and compare the
computational time of the proposed method with that of the previous
methods.
Abstract: It is hard to percept the interaction process with machines when visual information is not available. In this paper, we have addressed this issue to provide interaction through visual techniques. Posture recognition is done for American Sign Language to recognize static alphabets and numbers. 3D information is exploited to obtain segmentation of hands and face using normal Gaussian distribution and depth information. Features for posture recognition are computed using statistical and geometrical properties which are translation, rotation and scale invariant. Hu-Moment as statistical features and; circularity and rectangularity as geometrical features are incorporated to build the feature vectors. These feature vectors are used to train SVM for classification that recognizes static alphabets and numbers. For the alphabets, curvature analysis is carried out to reduce the misclassifications. The experimental results show that proposed system recognizes posture symbols by achieving recognition rate of 98.65% and 98.6% for ASL alphabets and numbers respectively.
Abstract: Since the 1940s, many promising telepresence
research results have been obtained. However, telepresence
technology still has not reached industrial usage. As human
intelligence is necessary for successful execution of most manual
assembly tasks, the ability of the human is hindered in some cases,
such as the assembly of heavy parts of small/medium lots or
prototypes. In such a case of manual assembly, the help of industrial
robots is mandatory. The telepresence technology can be considered
as a solution for performing assembly tasks, where the human
intelligence and haptic sense are needed to identify and minimize the
errors during an assembly process and a robot is needed to carry
heavy parts. In this paper, preliminary steps to integrate the
telepresence technology into industrial robot systems are introduced.
The system described here combines both, the human haptic sense
and the industrial robot capability to perform a manual assembly task
remotely using a force feedback joystick. Mapping between the
joystick-s Degrees of Freedom (DOF) and the robot-s ones are
introduced. Simulation and experimental results are shown and future
work is discussed.
Abstract: This paper considers the problem of scheduling maintenance actions for identical aircraft gas turbine engines. Each one of the turbines consists of parts which frequently require replacement. A finite inventory of spare parts is available and all parts are ready for replacement at any time. The inventory consists of both new and refurbished parts. Hence, these parts have different field lives. The goal is to find a replacement part sequencing that maximizes the time that the aircraft will keep functioning before the inventory is replenished. The problem is formulated as an identical parallel machine scheduling problem where the minimum completion time has to be maximized. Two models have been developed. The first one is an optimization model which is based on a 0-1 linear programming formulation, while the second one is an approximate procedure which consists in decomposing the problem into several two-machine subproblems. Each subproblem is optimally solved using the first model. Both models have been implemented using Lingo and have been tested on two sets of randomly generated data with up to 150 parts and 10 turbines. Experimental results show that the optimization model is able to solve only instances with no more than 4 turbines, while the decomposition procedure often provides near-optimal solutions within a maximum CPU time of 3 seconds.
Abstract: This paper presents the experimental results on effect of applied voltage stress frequency to the occurrence of electrical treeing in 22 kV cross linked polyethylene (XLPE) insulated cable.Hallow disk of XLPE insulating material with thickness 5 mm taken from unused high voltage cable was used as the specimen in this study. Stainless steel needle was inserted gradually into the specimen to give a tip to earth plane electrode separation of 2.50.2 mm at elevated temperature 105-110°C. The specimen was then annealed for 5 minute to minimize any mechanical stress build up around the needle-plane region before it was cooled down to room temperature. Each specimen were subjected to the same applied voltage stress level at 8 kV AC rms, with various frequency, 50, 100, 500, 1000 and 2000 Hz. Initiation time, propagation speed and pattern of electrical treeing were examined in order to study the effect of applied voltage stress frequency. By the experimental results, initial time of visible treeing decreases with increasing in applied voltage frequency. Also, obviously, propagation speed of electrical treeing increases with increasing in applied voltage frequency.Furthermore, two types of electrical treeing, bush-like and branch-like treeing were observed.The experimental results confirmed the effect of voltage stress frequency as well.
Abstract: In this paper motion analysis on a winding
stair-climbing is investigated using our proposed rotational arm type
of robotic wheelchair. For now, the robotic wheelchair is operated in
an open mode to climb winding stairs by a dynamic turning, therefore,
the dynamics model is required to ensure a passenger-s safety.
Equations of motion based on the skid-steering analysis are developed
for the trajectory planning and motion analysis on climbing winding
stairs. Since the robotic wheelchair must climb a winding staircase
stably, the winding trajectory becomes a constraint equation to be
followed, and the Baumgarte-s method is used to solve for the
constrained dynamics equations. Experimental results validate the
behavior of the prototype as it climbs a winding stair.
Abstract: Skin color based tracking techniques often assume a
static skin color model obtained either from an offline set of library
images or the first few frames of a video stream. These models
can show a weak performance in presence of changing lighting or
imaging conditions. We propose an adaptive skin color model based
on the Gaussian mixture model to handle the changing conditions.
Initial estimation of the number and weights of skin color clusters
are obtained using a modified form of the general Expectation
maximization algorithm, The model adapts to changes in imaging
conditions and refines the model parameters dynamically using spatial
and temporal constraints. Experimental results show that the method
can be used in effectively tracking of hand and face regions.
Abstract: This paper presents an approach for an unequal error
protection of facial features of personal ID images coding. We
consider unequal error protection (UEP) strategies for the efficient
progressive transmission of embedded image codes over noisy
channels. This new method is based on the progressive image
compression embedded zerotree wavelet (EZW) algorithm and UEP
technique with defined region of interest (ROI). In this case is ROI
equal facial features within personal ID image. ROI technique is
important in applications with different parts of importance. In ROI
coding, a chosen ROI is encoded with higher quality than the
background (BG). Unequal error protection of image is provided by
different coding techniques and encoding LL band separately. In our
proposed method, image is divided into two parts (ROI, BG) that
consist of more important bytes (MIB) and less important bytes
(LIB). The proposed unequal error protection of image transmission
has shown to be more appropriate to low bit rate applications,
producing better quality output for ROI of the compresses image.
The experimental results verify effectiveness of the design. The
results of our method demonstrate the comparison of the UEP of
image transmission with defined ROI with facial features and the
equal error protection (EEP) over additive white gaussian noise
(AWGN) channel.
Abstract: With the advent of digital cinema and digital
broadcasting, copyright protection of video data has been one of the
most important issues.
We present a novel method of watermarking for video image data
based on the hardware and digital wavelet transform techniques and
name it as “traceable watermarking" because the watermarked data is
constructed before the transmission process and traced after it has been
received by an authorized user.
In our method, we embed the watermark to the lowest part of each
image frame in decoded video by using a hardware LSI.
Digital Cinema is an important application for traceable
watermarking since digital cinema system makes use of watermarking
technology during content encoding, encryption, transmission,
decoding and all the intermediate process to be done in digital cinema
systems. The watermark is embedded into the randomly selected
movie frames using hash functions.
Embedded watermark information can be extracted from the
decoded video data. For that, there is no need to access original movie
data. Our experimental results show that proposed traceable
watermarking method for digital cinema system is much better than the
convenient watermarking techniques in terms of robustness, image
quality, speed, simplicity and robust structure.
Abstract: The results of the two-phase gas-solid jet in pneumatic
powder injection process analysis were presented in the paper. The
researches were conducted on model set-up with high speed camera
jet movement recording. Then the recorded material was analyzed to
estimate main particles movement parameters. The values obtained
from this direct measurement were compared to those calculated with
the use of the well-known formulas for the two-phase flows
(pneumatic conveying). Moreover, they were compared to
experimental results previously achieved by authors. The analysis led
to conclusions which to some extent changed the assumptions used
even by authors, regarding the two-phase jet in pneumatic powder
injection process. Additionally, the visual analysis of the recorded
clips supplied data to make a more complete evaluation of the jet
behavior in the lance outlet than before.
Abstract: Medical image data hiding has strict constrains such
as high imperceptibility, high capacity and high robustness.
Achieving these three requirements simultaneously is highly
cumbersome. Some works have been reported in the literature on
data hiding, watermarking and stegnography which are suitable for
telemedicine applications. None is reliable in all aspects. Electronic
Patient Report (EPR) data hiding for telemedicine demand it blind
and reversible. This paper proposes a novel approach to blind
reversible data hiding based on integer wavelet transform.
Experimental results shows that this scheme outperforms the prior
arts in terms of zero BER (Bit Error Rate), higher PSNR (Peak Signal
to Noise Ratio), and large EPR data embedding capacity with
WPSNR (Weighted Peak Signal to Noise Ratio) around 53 dB,
compared with the existing reversible data hiding schemes.
Abstract: Wavelet transform has been extensively used in
machine fault diagnosis and prognosis owing to its strength to deal
with non-stationary signals. The existing Wavelet transform based
schemes for fault diagnosis employ wavelet decomposition of the
entire vibration frequency which not only involve huge
computational overhead in extracting the features but also increases
the dimensionality of the feature vector. This increase in the
dimensionality has the tendency to 'over-fit' the training data and
could mislead the fault diagnostic model. In this paper a novel
technique, envelope wavelet packet transform (EWPT) is proposed in
which features are extracted based on wavelet packet transform of the
filtered envelope signal rather than the overall vibration signal. It not
only reduces the computational overhead in terms of reduced number
of wavelet decomposition levels and features but also improves the
fault detection accuracy. Analytical expressions are provided for the
optimal frequency resolution and decomposition level selection in
EWPT. Experimental results with both actual and simulated machine
fault data demonstrate significant gain in fault detection ability by
EWPT at reduced complexity compared to existing techniques.
Abstract: Following harvest, fresh produce needs to be cooled
immediately in a room where the air temperature and the relative air
humidity are controlled to maintain the produce quality. In this paper,
an experimental study for forced air cooling of fresh produce
(cauliflower) is performed using a pilot developed within our
laboratory. Furthermore, a numerical simulation of spherical
produces, taking into account the aerodynamic aspect and also the
heat transfer in the produce and in the air, was carried out using a
finite element method. At the end of this communication,
experimental results are presented and compared with the simulation.