Abstract: The posteroanterior manipulation technique is usually include in the procedure of the lumbar spine to evaluate the intervertebral motion according to mechanical resistance. The mechanical device with visual feedback was proposed that allows one to analysis the lumbar segments mobility “in vivo" facilitating for the therapist to take its treatment evolution. The measuring system uses load cell and displacement sensor to estimate spine stiffness. In this work, the device was tested by 2 therapists, female, applying posteroanterior force techniques to 5 volunteers, female, with frequency of approximately 1.2-1.8 Hz. A test-retest procedure was used for 2 periods of day. The visual feedback results small variation of forces and cycle time during 6 cycles rhythmic application. The stiffness values showed good agreement between test-retest procedures when used same order of maximum forces.
Abstract: The Sensor Network consists of densely deployed
sensor nodes. Energy optimization is one of the most important
aspects of sensor application design. Data acquisition and aggregation
techniques for processing data in-network should be energy efficient.
Due to the cross-layer design, resource-limited and noisy nature
of Wireless Sensor Networks(WSNs), it is challenging to study
the performance of these systems in a realistic setting. In this
paper, we propose optimizing queries by aggregation of data and
data redundancy to reduce energy consumption without requiring
all sensed data and directed diffusion communication paradigm to
achieve power savings, robust communication and processing data
in-network. To estimate the per-node power consumption POWERTossim
mica2 energy model is used, which provides scalable and
accurate results. The performance analysis shows that the proposed
methods overcomes the existing methods in the aspects of energy
consumption in wireless sensor networks.
Abstract: The need for micromechanical inertial sensors is increasing
in future electronic stability control (ESC) and other positioning,
navigation and guidance systems. Due to the rising density of
sensors in automotive and consumer devices the goal is not only to get
high performance, robustness and smaller package sizes, but also to
optimize the energy management of the overall sensor system. This
paper presents an evaluation concept for a surface micromachined
yaw rate sensor. Within this evaluation concept an energy-efficient
operation of the drive mode of the yaw rate sensor is enabled. The
presented system concept can be realized within a power management
subsystem.
Abstract: A healthcare monitoring system is presented in this
paper. This system is based on ultra-low power sensor nodes and a
personal server, which is based on hardware and software extensions
to a Personal Digital Assistant (PDA)/Smartphone. The sensor node
collects data from the body of a patient and sends it to the personal
server where the data is processed, displayed and made ready to be
sent to a healthcare network, if necessary. The personal server
consists of a compact low power receiver module and equipped with
a Smartphone software. The receiver module takes less than 30 × 30
mm board size and consumes approximately 25 mA in active mode.
Abstract: This study aims at using multi-source data to monitor
coral biodiversity and coral bleaching. We used coral reef at Racha
Islands, Phuket as a study area. There were three sources of data:
coral diversity, sensor based data and satellite data.
Abstract: Blood pulse is an important human physiological signal commonly used for the understanding of the individual physical health. Current methods of non-invasive blood pulse sensing require direct contact or access to the human skin. As such, the performances of these devices tend to vary with time and are subjective to human body fluids (e.g. blood, perspiration and skin-oil) and environmental contaminants (e.g. mud, water, etc). This paper proposes a simulation model for the novel method of non-invasive acquisition of blood pulse using the disturbance created by blood flowing through a localized magnetic field. The simulation model geometry represents a blood vessel, a permanent magnet, a magnetic sensor, surrounding tissues and air in 2-dimensional. In this model, the velocity and pressure fields in the blood stream are described based on Navier-Stroke equations and the walls of the blood vessel are assumed to have no-slip condition. The blood assumes a parabolic profile considering a laminar flow for blood in major artery near the skin. And the inlet velocity follows a sinusoidal equation. This will allow the computational software to compute the interactions between the magnetic vector potential generated by the permanent magnet and the magnetic nanoparticles in the blood. These interactions are simulated based on Maxwell equations at the location where the magnetic sensor is placed. The simulated magnetic field at the sensor location is found to assume similar sinusoidal waveform characteristics as the inlet velocity of the blood. The amplitude of the simulated waveforms at the sensor location are compared with physical measurements on human subjects and found to be highly correlated.
Abstract: An optical fiber Fabry-Perot interferometer (FFPI) is
proposed and demonstrated for dynamic measurements in a
mechanical vibrating target. A polishing metal with a low reflectance
value adhered to a mechanical vibrator was excited via a function
generator at various excitation frequencies. Output interference
fringes were generated by modulating the reference and sensing
signal at the output arm. A fringe-counting technique was used for
interpreting the displacement information on the dedicated computer.
The fiber interferometer has been found the capability of the
displacement measurements of 1.28 μm – 96.01 μm. A commercial
displacement sensor was employed as a reference sensor for
investigating the measurement errors from the fiber sensor. A
maximum percentage measurement error of approximately 1.59 %
was obtained.
Abstract: This paper describes the process used in the
automation of the Maritime UAV commands using the Kinect sensor.
The AR Drone is a Quadrocopter manufactured by Parrot [1] to be
controlled using the Apple operating systems such as iPhones and
Ipads. However, this project uses the Microsoft Kinect SDK and
Microsoft Visual Studio C# (C sharp) software, which are compatible
with Windows Operating System for the automation of the navigation
and control of the AR drone.
The navigation and control software for the Quadrocopter runs on
a windows 7 computer. The project is divided into two sections; the
Quadrocopter control system and the Kinect sensor control system.
The Kinect sensor is connected to the computer using a USB cable
from which commands can be sent to and from the Kinect sensors.
The AR drone has Wi-Fi capabilities from which it can be connected
to the computer to enable transfer of commands to and from the
Quadrocopter.
The project was implemented in C#, a programming language that
is commonly used in the automation systems. The language was
chosen because there are more libraries already established in C# for
both the AR drone and the Kinect sensor.
The study will contribute toward research in automation of
systems using the Quadrocopter and the Kinect sensor for navigation
involving a human operator in the loop. The prototype created has
numerous applications among which include the inspection of vessels
such as ship, airplanes and areas that are not accessible by human
operators.
Abstract: Many agricultural and especially greenhouse
applications like plant inspection, data gathering, spraying and
selective harvesting could be performed by robots. In this paper
multiple nonholonomic robots are used in order to create a desired
formation scheme for screening solar energy in a greenhouse through
data gathering. The formation consists from a leader and a team
member equipped with appropriate sensors. Each robot is dedicated
to its mission in the greenhouse that is predefined by the
requirements of the application. The feasibility of the proposed
application includes experimental results with three unmanned
ground vehicles (UGV).
Abstract: In this paper, acoustic techniques are used to detect hidden insect infestations of date palm tress (Phoenix dactylifera L.). In particular, we use an acoustic instrument for early discovery of the presence of a destructive insect pest commonly known as the Red Date Palm Weevil (RDPW) and scientifically as Rhynchophorus ferrugineus (Olivier). This type of insect attacks date palm tress and causes irreversible damages at late stages. As a result, the infected trees must be destroyed. Therefore, early presence detection is a major part in controlling the spread and economic damage caused by this type of infestation. Furthermore monitoring and early detection of the disease can asses in taking appropriate measures such as isolating or treating the infected trees. The acoustic system is evaluated in terms of its ability for early discovery of hidden bests inside the tested tree. When signal acquisitions is completed for a number of date palms, a signal processing technique known as time-frequency analysis is evaluated in terms of providing an estimate that can be visually used to recognize the acoustic signature of the RDPW. The testing instrument was tested in the laboratory first then; it was used on suspected or infested tress in the field. The final results indicate that the acoustic monitoring approach along with signal processing techniques are very promising for the early detection of presence of the larva as well as the adult pest in the date palms.
Abstract: Vertical ZnO nanowire array films were synthesized
based on aqueous method for sensing applications. ZnO nanowires
were investigated structurally using X-ray diffraction (XRD) and
scanning electron microscopy (SEM). The gas-sensing properties of
ZnO nanowires array films are studied. It is found that the ZnO
nanowires array film sensor exhibits excellent sensing properties
towards O2 and CO2 at 100 °C with the response time shorter than 5
s. High surface area / volume ratio of vertical ZnO nanowire and high
mobility accounts for the fast response and recovery. The sensor
response was measured in the range from 100 to 500 ppm O2 and CO2
in this study.
Abstract: The use of electronic sensors in the electronics
industry has become increasingly popular over the past few years,
and it has become a high competition product. The frequency
adjustment process is regarded as one of the most important process
in the electronic sensor manufacturing process. Due to inaccuracies
in the frequency adjustment process, up to 80% waste can be caused
due to rework processes; therefore, this study aims to provide a
preliminary understanding of the role of parameters used in the
frequency adjustment process, and also make suggestions in order to
further improve performance. Four parameters are considered in this
study: air pressure, dispensing time, vacuum force, and the distance
between the needle tip and the product. A full factorial design for
experiment 2k was considered to determine those parameters that
significantly affect the accuracy of the frequency adjustment process,
where a deviation in the frequency after adjustment and the target
frequency is expected to be 0 kHz. The experiment was conducted on
two levels, using two replications and with five center-points added.
In total, 37 experiments were carried out. The results reveal that air
pressure and dispensing time significantly affect the frequency
adjustment process. The mathematical relationship between these
two parameters was formulated, and the optimal parameters for air
pressure and dispensing time were found to be 0.45 MPa and 458 ms,
respectively. The optimal parameters were examined by carrying out
a confirmation experiment in which an average deviation of 0.082
kHz was achieved.
Abstract: The removal efficiency of 4-chlorophenol with
different advanced oxidation processes have been studied. Oxidation
experiments were carried out using two 4-chlorophenol
concentrations: 100 mg L-1 and 250 mg L-1 and UV generated from a
KrCl excilamp with (molar ratio H2O2: 4-chlorophenol = 25:1) and
without H2O2, and, with Fenton process (molar ratio H2O2:4-
chlorophenol of 25:1 and Fe2+ concentration of 5 mg L-1).
The results show that there is no significant difference in the 4-
chlorophenol conversion when using one of the three assayed
methods. However, significant concentrations of the photoproductos
still remained in the media when the chosen treatment involves UV
without hydrogen peroxide. Fenton process removed all the
intermediate photoproducts except for the hydroquinone and the
1,2,4-trihydroxybenzene. In the case of UV and hydrogen peroxide
all the intermediate photoproducts are removed.
Microbial bioassays were carried out utilising the naturally
luminescent bacterium Vibrio fischeri and a genetically modified
Pseudomonas putida isolated from a waste treatment plant receiving
phenolic waste. The results using V. fischeri show that with samples
after degradation, only the UV treatment showed toxicity (IC50 =38)
whereas with H2O2 and Fenton reactions the samples exhibited no
toxicity after treatment in the range of concentrations studied. Using
the Pseudomonas putida biosensor no toxicity could be detected for
all the samples following treatment due to the higher tolerance of the
organism to phenol concentrations encountered.
Abstract: This paper aims at overviewing the topics of a research project (CARDIOSENSOR) on the field of health sciences (biomaterials and biomedical engineering). The project has focused on the development of a nanosensor for the assessment of the risk of cardiovascular diseases by the monitoring of C-reactive protein (CRP), which has been currently considered as the best validated inflammatory biomarker associated to cardiovascular diseases. The project involves tasks such as: 1) the development of sensor devices based on field effect transistors (FET): assembly, optimization and validation; 2) application of sensors to the detection of CRP in standard solutions and comparison with enzyme-linked immunosorbent assay (ELISA); and 3) application of sensors to real samples such as blood and saliva and evaluation of their ability to predict the risk of cardiovascular disease.
Abstract: Physiological control of a left ventricle assist device (LVAD) is generally a complicated task due to diverse operating environments and patient variability. In this work, a tracking control algorithm based on sliding mode and feed forward control for a class of discrete-time single input single output (SISO) nonlinear uncertain systems is presented. The controller was developed to track the reference trajectory to a set operating point without inducing suction in the ventricle. The controller regulates the estimated mean pulsatile flow Qp and mean pulsatility index of pump rotational speed PIω that was generated from a model of the assist device. We recall the principle of the sliding mode control theory then we combine the feed-forward control design with the sliding mode control technique to follow the reference trajectory. The uncertainty is replaced by its upper and lower boundary. The controller was tested in a computer simulation covering two scenarios (preload and ventricular contractility). The simulation results prove the effectiveness and the robustness of the proposed controller
Abstract: In this paper, we propose the pre-processor based on
the Evidence Supporting Measure of Similarity (ESMS) filter and also
propose the unified fusion approach (UFA) based on the general
fusion machine coupled with ESMS filter, which improve the
correctness and precision of information fusion in any fields of
application. Here we mainly apply the new approach to Simultaneous
Localization And Mapping (SLAM) of Pioneer II mobile robots. A
simulation experiment was performed, where an autonomous virtual
mobile robot with sonar sensors evolves in a virtual world map with
obstacles. By comparing the result of building map according to the
general fusion machine (here DSmT-based fusing machine and
PCR5-based conflict redistributor considereded) coupling with ESMS
filter and without ESMS filter, it shows the benefit of the selection of
the sources as a prerequisite for improvement of the information
fusion, and also testifies the superiority of the UFA in dealing with
SLAM.
Abstract: Acoustic Imaging based sound localization using microphone
array is a challenging task in digital-signal processing.
Discrete Fourier transform (DFT) based near-field acoustical holography
(NAH) is an important acoustical technique for sound source
localization and provide an efficient solution to the ill-posed problem.
However, in practice, due to the usage of small curtailed aperture
and its consequence of significant spectral leakage, the DFT could
not reconstruct the active-region-of-sound (AROS) effectively, especially
near the edges of aperture. In this paper, we emphasize the
fundamental problems of DFT-based NAH, provide a solution to
spectral leakage effect by the extrapolation based on linear predictive
coding and 2D Tukey windowing. This approach has been tested to
localize the single and multi-point sound sources. We observe that
incorporating extrapolation technique increases the spatial resolution,
localization accuracy and reduces spectral leakage when small curtail
aperture with a lower number of sensors accounts.
Abstract: A novel low-cost impedance control structure is
proposed for monitoring the contact force between end-effector and
environment without installing an expensive force/torque sensor.
Theoretically, the end-effector contact force can be estimated from the
superposition of each joint control torque. There have a nonlinear
matrix mapping function between each joint motor control input and
end-effector actuating force/torques vector. This new force control
structure can be implemented based on this estimated mapping matrix.
First, the robot end-effector is manipulated to specified positions, then
the force controller is actuated based on the hall sensor current
feedback of each joint motor. The model-free fuzzy sliding mode
control (FSMC) strategy is employed to design the position and force
controllers, respectively. All the hardware circuits and software
control programs are designed on an Altera Nios II embedded
development kit to constitute an embedded system structure for a
retrofitted Mitsubishi 5 DOF robot. Experimental results show that PI
and FSMC force control algorithms can achieve reasonable contact
force monitoring objective based on this hardware control structure.
Abstract: Because of the low maintenance and robustness induction motors have many applications in the industries. The speed control of induction motor is more important to achieve maximum torque and efficiency. Various speed control techniques like, Direct Torque Control, Sensorless Vector Control and Field Oriented Control are discussed in this paper. Soft computing technique – Fuzzy logic is applied in this paper for the speed control of induction motor to achieve maximum torque with minimum loss. The fuzzy logic controller is implemented using the Field Oriented Control technique as it provides better control of motor torque with high dynamic performance. The motor model is designed and membership functions are chosen according to the parameters of the motor model. The simulated design is tested using various tool boxes in MATLAB. The result concludes that the efficiency and reliability of the proposed speed controller is good.
Abstract: Safer driver behavior promoting is the main goal of this paper. It is a fact that drivers behavior is relatively safer when being monitored. Thus, in this paper, we propose a monitoring system to report specific driving event as well as the potentially aggressive events for estimation of the driving performance. Our driving monitoring system is composed of two parts. The first part is the in-vehicle embedded system which is composed of a GPS receiver, a two-axis accelerometer, radar sensor, OBD interface, and GPRS modem. The design considerations that led to this architecture is described in this paper. The second part is a web server where an adaptive hierarchical fuzzy system is proposed to classify the driving performance based on the data that is sent by the in-vehicle embedded system and the data that is provided by the geographical information system (GIS). Our system is robust, inexpensive and small enough to fit inside a vehicle without distracting the driver.