Abstract: The Sigma-Delta A/D converters have been proposed
as a practical application for A/D conversion at high rates because of
its simplicity and robustness to imperfections in the circuit, also
because the traditional converters are more difficult to implement in
VLSI technology. These difficulties with conventional conversion
methods need precise analog components in their filters and
conversion circuits, and are more vulnerable to noise and
interference. This paper aims to analyze the architecture, function and
application of Analog-Digital converters (A/D) Sigma-Delta to
overcome these difficulties, showing some simulations using the
Simulink software and Multisim.
Abstract: A simple, accurate and precise direct spectrophotometric method has been developed for the determination of cefixime in tablets and capsules. The method is based on the reaction of cefixime with a mixture of potassium iodide and potassium iodate to form yellow coloured product in ethanol-distilled water medium at room temperature which absorbed maximally at 352 nm. The factors affecting the reaction product were carefully studied and optimized. The validation parameters based on International Conference on Harmonisation (ICH, USA) guidelines were followed. The effect of common excipients used as additives has been tested and the tolerance limit was calculated for the determination of cefixime. Beer’s law is obeyed in the concentration range of 4 – 24 ug mL-1 with apparent molar absorptivity of 1.52 × 104 L mol-1cm-1 and Sandell’s sensitivity of 0.033 ug/cm2/ 0.001 absorbance unit. The limits of detection and quantitation for the proposed method are 0.32 and 1.06 ug mL-1, respectively. The proposed method has been successfully applied for the determination of cefixime in pharmaceutical formulations. The results obtained by the proposed method were statistically compared with the reference method using t- and F- values and found no significant difference between the two methods. The proposed method can be used as an alternate method for routine quality control analysis of cefixime in pharmaceutical formulations.
Abstract: This paper explores competencies that managers of
small firms in Ghana use to enhance operational flexibility towards
the attainment of higher productivity. This is because the requisite
competence required of such managers to be effective performers
continues to be a challenge. Data was collected from managers of
three hundred small firms using a standardized self-completion
questionnaire and analyzed using the Amos-based structural equation
model approach. Findings from factor and confirmatory factor
analyses showed that the only competence exhibited by managers
toward effective performance is realistic practices evident at the
workplace. It is concluded that a manager’s self-confidence and
involvement in areas that he/she is good at, and his/her possession of
skills that enables performance at high capacity are indications of the
manger’s effectiveness. The study outcome provides a knowledge
base helpful to policy-makers, especially in Ghana, in determining
the requisite managerial competences required by small firm
managers for effective performance.
Abstract: Nowadays, the amounts of companies which tend to
have an Enterprise Resource Planning (ERP) application are
increasing. Although ERP projects are expensive, time consuming,
and complex, there are some successful experiences. These days,
developing countries are striving to implement ERP projects
successfully; however, there are many obstacles. Therefore, these
projects would be failed or partially failed. This paper concerns the
implementation of a successful ERP implementation, IFS, in Iran at
Dana Geophysics Company (DGC). After a short review of ERP and
ERP market in Iran, we propose a three phases deployment
methodology (phase 1: Preparation and Business Process
Management (BPM) phase 2: implementation and phase 3: testing,
golive-1 (pilot) and golive-2 (final)). Then, we present five guidelines
(Project Management, Change Management, Business Process
Management (BPM), Training& Knowledge Management, and
Technical Management), which were chose as work streams. In this
case study we present lessons learned in Project management and
Business process Management.
Abstract: The main objective of this study was to identify
factors and conditions that motivated and encouraged students
towards the math class and the factors that made this class an
attractive and lovely one. To do this end, questionnaires consisting of
15 questions were distributed among 85 math teachers working in
schools of Zahedan. Having collected and reviewed these
questionnaires, it was shown that doing activity in math class
(activity of students while teaching) and previous math teachers'
behaviors have had much impact on encouraging the students
towards mathematics. Separation of educational classroom of
mathematics from the main classroom (which is decorated with crafts
created by students themselves with regard to math book including
article, wall newspaper, figures and formulas), peers, size and
appearance of math book, first grade teachers in each educational
level, among whom the Elementary first grade teachers had more
importance and impact, were among the most influential and
important factors in this regard. Then, school environment, family,
conducting research related to mathematics, its application in daily
life and other courses and studying the history of mathematics were
categorized as important factors that would increase the students’
interest in mathematics.
Abstract: This paper deals with a simulation programs and
technologies using in the educational process for members of the crisis
management. Risk analysis, simulation, preparation and planning are
among the main activities of workers of crisis management. Made
correctly simulation of emergency defines the extent of the danger. On
this basis, it is possible to effectively prepare and plan measures to
minimize damage. The paper is focused on simulation programs that
are trained at the University of Defence. Implementation of the outputs
from simulation programs in decision-making processes of crisis staffs
is one of the main tasks of the research project.
Abstract: The aim of this work is to present a theoretical analysis of a 2D ultrasound transducer comprised of crossed arrays of metal strips placed on both sides of thin piezoelectric layer (a). Such a structure is capable of electronic beam-steering of generated wavebeam both in elevation and azimuth. In this paper a semi-analytical model of the considered transducer is developed. It is based on generalization of the well-known BIS-expansion method. Specifically, applying the electrostatic approximation, the electric field components on the surface of the layer are expanded into fast converging series of double periodic spatial harmonics with corresponding amplitudes represented by the properly chosen Legendre polynomials. The problem is reduced to numerical solving of certain system of linear equations for unknown expansion coefficients.
Abstract: In this study, the evaluation of thermal stability of the
micrometer-sized silica particle reinforced epoxy composite was
carried out through the measurement of thermal expansion coefficient
and Young’s modulus of the specimens. For all the specimens in this
study from the baseline to those containing 50 wt% silica filler, the
thermal expansion coefficients and the Young’s moduli were
gradually decreased down to 20% and increased up to 41%,
respectively. The experimental results were compared with fillervolume-
based simple empirical relations. The experimental results of
thermal expansion coefficients correspond with those of Thomas’s
model which is modified from the rule of mixture. However, the
measured result for Young’s modulus tends to be increased slightly.
The differences in increments of the moduli between experimental and
numerical model data are quite large.
Abstract: In addition to the production, which is already
frequently optimized, improving the distribution logistics also opens
up tremendous potential for increasing an enterprise’s
competitiveness. Here too though, numerous interactions need to be
taken into account, enterprises thus need to be able to identify and
weigh between different potentials for economically efficient
optimizations. In order to be able to assess potentials, enterprises
require a suitable method. This paper first briefly presents the need
for this research before introducing the procedure that will be used to
develop an appropriate method that not only considers interactions
but is also quickly and easily implemented.
Abstract: The reduction of greenhouse gases emissions is highly
discussed ecological theme at present. In addition to power industry
also main production sectors of binders, i.e. cement, air and hydraulic
lime are very sensitive to these questions. One of the possibilities
how CO2 emissions can be reduced directly at clinker burnout is
represented by partial substitution of lime with a material containing
limy ions at absence of carbonate group. Fluidised fly ash is one of
such potential raw materials where CaO can be found free and also
bound in anhydrite, CaSO4. At application of FBC (fluidized bed
combustion) fly ash with approximate 20% CaO content and its
dosing ratio to high percent lime 1:2, corresponding stechiometrically
to the preparation of raw material powder, approximately 0,37 t CO2
per 1 ton of one-component cement would be released at clinker
burnout compared to 0,46 t CO2 when orthodox raw materials are
used. The reduction of CO2 emissions thus could reach even 20%.
Abstract: The aim of the present study is to investigate the
potential use of the selected seed oils. The oil was extracted using
Soxhlet apparatus and the physicochemical characteristics of the oil
determined using standard methods. The following results were
obtained for the physicochemical parameters analysed: for Egusi seed
oil, Oil yield 53.20%, Saponification value 178.03±1.25 mgKOH/g,
Iodine value 49.10±0.32 g I2/100g, Acid value 4.30±0.86 mgKOH/g,
and Peroxide value 5.80±0.27 meq/kg were obtained. For Pawpaw
seed oil, Oil yield 40.10%, Saponification value 24.13±3.93
mgKOH/g, Iodine value 24.87±0.19 g I2/100g, Acid value 9.46±0.40
mgKOH/g, and Peroxide value 3.12±1.22 meq/kg were obtained. For
Sweet orange seed oil, Oil yield 43.10%, Saponification value
106.30±2.37 mgKOH/g, Iodine value 37.08±0.04 g I2/100g, Acid
value 7.59±0.77 mgKOH/g, and Peroxide value 2.21±0.46 meq/kg
were obtained. From the obtained values of the determined
parameters, the oils can be extracted from the three selected seeds in
commercial quantities and that the egusi and sweet orange seed oils
may be utilized in the industrial soap production.
Abstract: This paper presents a comparison of the reference
management software between Zotero and Mendeley and the results
were drawn by comparing the two software’s. The novelty of this
paper is the comparative analysis of the software and it has shown
that Mendeley can import more information from the Google Scholar
for the researchers. This finding can help to know researchers to use
the reference management software.
Abstract: Kinematic data wisely correlate vector quantities in
space to scalar parameters in time to assess the degree of symmetry
between the intact limb and the amputated limb with respect to a
normal model derived from the gait of control group participants.
Furthermore, these particular data allow a doctor to preliminarily
evaluate the usefulness of a certain rehabilitation therapy.
Kinetic curves allow the analysis of ground reaction forces (GRFs)
to assess the appropriateness of human motion.
Electromyography (EMG) allows the analysis of the fundamental
lower limb force contributions to quantify the level of gait
asymmetry. However, the use of this technological tool is expensive
and requires patient’s hospitalization. This research work suggests
overcoming the above limitations by applying artificial neural
networks.
Abstract: Red River Gum (Eucalyptus camaldulensis) is a tree
of the genus Eucalyptus widely distributed in Algeria and in the
world. The value of its aromatic secondary metabolites offers new
perspectives in the pharmaceutical industry. This strategy can
contribute to the sustainable development of our country. Preliminary
tests performed on the essential oil of Eucalyptus camendulensis
showed that this oil has antibacterial activity vis-à-vis the bacterial
strains (Enterococcus feacalis, Enterobacter cloaceai, Proteus
microsilis, Escherichia coli, Klebsiella pneumonia, and Pseudomonas
aeruginosa) and antifungic (Fusarium sporotrichioide and Fusarium
graminearum). The culture medium used was nutrient broth Muller
Hinton. The interaction between the bacteria and the essential oil is
expressed by a zone of inhibition with diameters of MIC indirectly
expression of. And we used the PDA medium to determine the fungal
activity. The extraction of the aromatic fraction (essentially oilhydrolat)
of the fresh aerian part of the Eucalyptus camendulensis
was performed by hydrodistillation. The average essential oil yield is
0.99%. The antimicrobial and fungal study of the essential oil and
hydrosol showed a high inhibitory effect on the growth of pathogens.
Abstract: Over the past era, there have been a lot of efforts and
studies are carried out in growing proficient tools for performing
various tasks in big data. Recently big data have gotten a lot of
publicity for their good reasons. Due to the large and complex
collection of datasets it is difficult to process on traditional data
processing applications. This concern turns to be further mandatory
for producing various tools in big data. Moreover, the main aim of
big data analytics is to utilize the advanced analytic techniques
besides very huge, different datasets which contain diverse sizes from
terabytes to zettabytes and diverse types such as structured or
unstructured and batch or streaming. Big data is useful for data sets
where their size or type is away from the capability of traditional
relational databases for capturing, managing and processing the data
with low-latency. Thus the out coming challenges tend to the
occurrence of powerful big data tools. In this survey, a various
collection of big data tools are illustrated and also compared with the
salient features.
Abstract: In this study, first thermoplastic composite materials
/plates that have high ballistic impact resistance were produced. For
this purpose, the thermoplastic prepreg and the vacuum bagging
technique were used to produce a composite material. Thermoplastic
prepregs (resin-impregnated fiber) that are supplied ready to be used,
namely high-density polyethylene (HDPE) was chosen as matrix and
unidirectional glass fiber was used as reinforcement. In order to
compare the fiber configuration effect on mechanical properties,
unidirectional and biaxial prepregs were used. Then the
microstructural properties of the composites were investigated with
scanning electron microscopy (SEM) analysis. Impact properties of
the composites were examined by Charpy impact test and tensile
mechanical tests and then the effects of ultraviolet irradiation were
investigated on mechanical performance.
Abstract: The lactic acid bacteria (LAB) were isolated from
10 samples of fermented foods (Sa-tor-dong and Bodo) in South
locality of Thailand. The 23 isolates of lactic acid bacteria were
selected, which were exhibited a clear zone and growth on MRS
agar supplemented with CaCO3. All of lactic acid bacteria were
tested on morphological and biochemical. The result showed that
all isolates were Gram’s positive, non-spore forming but only
10 isolates displayed catalase negative. The 10 isolates including
BD1 .1, BD 1.2, BD 2.1, BD2.2, BD 2.3, BD 3.1, BD 4.1, BD 5.2,
ST 4.1 and ST 5.2 were selected for inhibition activity
determination. Only 2 strains (ST 4.1 and BD 2.3) showed
inhibition zone on agar, when using Escherichia coli sp. as target
strain. The ST 4.1 showed highest inhibition zone on agar, which
was selected for probiotic property testing. The ST4.1 isolate
could grow in MRS broth containing a high concentration of
sodium chloride 6%, bile salts 7%, pH 4-10 and vary temperature
at 15-45°C.
Abstract: With demand for primary energy continuously
growing, search for renewable and efficient energy sources has been
high on agenda of our society. One of the most promising energy
sources is biogas technology. Residues coming from dairy industry
and milk processing could be used in biogas production; however,
low efficiency and high cost impede wide application of such
technology. One of the main problems is management and conversion
of organic residues through the anaerobic digestion process which is
characterized by acidic environment due to the low whey pH (
Abstract: Estimation of a proportion has many applications in
economics and social studies. A common application is the estimation
of the low income proportion, which gives the proportion of people
classified as poor into a population. In this paper, we present this
poverty indicator and propose to use the logistic regression estimator
for the problem of estimating the low income proportion. Various
sampling designs are presented. Assuming a real data set obtained
from the European Survey on Income and Living Conditions, Monte
Carlo simulation studies are carried out to analyze the empirical
performance of the logistic regression estimator under the various
sampling designs considered in this paper. Results derived from
Monte Carlo simulation studies indicate that the logistic regression
estimator can be more accurate than the customary estimator under
the various sampling designs considered in this paper. The stratified
sampling design can also provide more accurate results.
Abstract: The study area is Zaria, located in the basement
complex of northern Nigeria. The rock type forming the major part of
the Zaria batholith is granite. This research work was carried out to
compare the responses of seismic refraction tomography and
resistivity tomography in the same geologic environment and under
the same conditions. Hence, the choice of the site that has a visible
granitic outcrop that extends across a narrow stream channel and is
flanked by unconsolidated overburden, a neutral profile that was
covered by plain overburden and a site with thick lateritic cover
became necessary. The results of the seismic and resistivity
tomography models reveals that seismic velocity and resistivity does
not always simultaneously increase with depth, but their responses in
any geologic environment are determined by changes in the
mechanical and chemical content of the rock types rather than depth.