Abstract: Most of ignition delay correlations studies have been
developed in a constant volume bombs which cannot capture the
dynamic variation in pressure and temperature during the ignition
delay as in real engines. Watson, Assanis et. al. and Hardenberg
and Hase correlations have been developed based on experimental
data of diesel engines. However, they showed limited predictive
ability of ignition delay when compared to experimental results. The
objective of the study was to investigate the dependency of ignition
delay time on engine brake power. An experimental investigation of
the effect of automotive diesel and water diesel emulsion fuels on
ignition delay under steady state conditions of a direct injection diesel
engine was conducted. A four cylinder, direct injection naturally
aspirated diesel engine was used in this experiment over a wide range
of engine speeds and two engine loads. The ignition delay
experimental data were compared with predictions of Assanis et. al.
and Watson ignition delay correlations. The results of the
experimental investigation were then used to develop a new ignition
delay correlation. The newly developed ignition delay correlation has
shown a better agreement with the experimental data than Assanis et.
al. and Watson when using automotive diesel and water diesel
emulsion fuels especially at low to medium engine speeds at both
loads. In addition, the second derivative of cylinder pressure which is
the most widely used method in determining the start of combustion
was investigated.
Abstract: The Taiwan Health Literacy Scale (THLS) was developed to cope with the need of measuring heath literacy of Chinese-speaking adults in Taiwan. Although the scale was proven having good reliability and validity, it was not popularly adopted by the practitioners due to the length, and the time required completing. Based on the THLS, this research further invited healthcare professionals to review the original scale for a possible shorten work. Under the logic of THLS, the research adopted an analytic hierarchy process technique to consolidate the healthcare experts- assessments to shorten the original scale. There are fifteen items out of the original 66 items were identified having higher loadings. Confirmed by the experts and passed a pilot test with 40 undergraduate students, a short form of THLS is then introduced. This research then used 839 samples from the major cities of the Hua-lien county in the eastern part of Taiwan to test the reliability and validity of this new scale. The reliability of the scale is high and acceptable. The current scale is also highly correlated with the original, of which provide evidence for the validity of the scale.
Abstract: This paper presents design and characterization of a
microaccelerometer designated for integration into cataract surgical
probe to detect hardness of different eye tissues during cataract
surgery. Soft posterior lens capsule of eye can be easily damaged in
comparison with hard opaque lens since the surgeon can not see
directly behind cutting needle during the surgery. Presence of
microsensor helps the surgeon to avoid rupturing posterior lens
capsule which if occurs leads to severe complications such as
glaucoma, infection, or even blindness. The microsensor having
overall dimensions of 480 μm x 395 μm is able to deliver significant
capacitance variations during encountered vibration situations which
makes it capable to distinguish between different types of tissue.
Integration of electronic components on chip ensures high level of
reliability and noise immunity while minimizes space and power
requirements. Physical characteristics and results on performance
testing, proves integration of microsensor as an effective tool to aid
the surgeon during this procedure.
Abstract: The number of people using SNS with their mobile devices is soaring. This research focuses on the Twitter service that has the most third-party applications and delved into the fact that there were not sufficient studies on the UX design aspects of Twitter applications. Among social network services which have emerged as a major social topic lately, this research try to analyze the UX design of the Twitter application which is also called micro-blogging service. Therefore this research sets its goal to draw components of the UX design aspect of the Tweeter application on which there are not enough analysis yet. Moreover, this research suggests improvement of mobile application which will assure better users- experience. In order to analyze the UX design aspect of the mobile twitter application, with relevant document and user research, evaluating factors of the UX Design which would affect users- experience were organized. The subjects for cases were selected among six paid and free social networking applications that had been consistently ranked from 1st to 100th in the Korean application store during May, 2012 after closely monitoring the rank. From May 15th to May 11th in 2012, in accordance with the evaluating standard, surveys were conducted in a form of interviews with 20 subjects who have used the Twitter application to find out problems and solutions for the UX design of the mobile Twitter application.
Abstract: The corrugated steel cladding used to cover most of
steel buildings is considered as non-structural element. This research
will reflect the effect of cladding as a shear diaphragm in increasing
the normal elastic capacity of columns. This study is important
because of the lack of information of the behavior of cladding and
secondary members in various codes. Mathematical models for six
different cases are carried by software. The results extracted from the
program have been plotted showing the effects of different variables
on the ultimate load of column. The variables considered in our
research are the spacing between columns and the thickness of the
corrugated sheet representing the sheet stiffness.
Abstract: The proposed Multimedia Pronunciation Learning
Management System (MPLMS) in this study is a technology with
profound potential for inducing improvement in pronunciation
learning. The MPLMS optimizes the digitised phonetic symbols with
the integration of text, sound and mouth movement video. The
components are designed and developed in an online management
system which turns the web to a dynamic user-centric collection of
consistent and timely information for quality sustainable learning.
The aim of this study is to design and develop the MPLMS which
serves as an innovative tool to improve English pronunciation. This
paper discusses the iterative methodology and the three-phase Alessi
and Trollip model in the development of MPLMS. To align with the
flexibility of the development of educational software, the iterative
approach comprises plan, design, develop, evaluate and implement is
followed. To ensure the instructional appropriateness of MPLMS, the
instructional system design (ISD) model of Alessi and Trollip serves
as a platform to guide the important instructional factors and process.
It is expected that the results of future empirical research will support
the efficacy of MPLMS and its place as the premier pronunciation
learning system.
Abstract: This paper examines the forced convection flow of
incompressible, electrically conducting viscous fluid past a sharp
wedge in the presence of heat generation or absorption with an
applied magnetic field. The system of partial differential equations
governing Falkner - Skan wedge flow and heat transfer is first
transformed into a system of ordinary differential equations using
similarity transformations which is later solved using an implicit
finite - difference scheme, along with quasilinearization technique.
Numerical computations are performed for air (Pr = 0.7) and
displayed graphically to illustrate the influence of pertinent physical
parameters on local skin friction and heat transfer coefficients and,
also on, velocity and temperature fields. It is observed that the
magnetic field increases both the coefficients of skin friction and heat
transfer. The effect of heat generation or absorption is found to be
very significant on heat transfer, but its effect on the skin friction is
negligible. Indeed, the occurrence of overshoot is noticed in the
temperature profiles during heat generation process, causing the
reversal in the direction of heat transfer.
Abstract: We study bifurcation structure of the zonal jet flow the
streamfunction of which is expressed by a single spherical harmonics
on a rotating sphere. In the non-rotating case, we find that a steady
traveling wave solution arises from the zonal jet flow through Hopf
bifurcation. As the Reynolds number increases, several traveling
solutions arise only through the pitchfork bifurcations and at high
Reynolds number the bifurcating solutions become Hopf unstable. In
the rotating case, on the other hand, under the stabilizing effect of
rotation, as the absolute value of rotation rate increases, the number
of the bifurcating solutions arising from the zonal jet flow decreases
monotonically. We also carry out time integration to study unsteady
solutions at high Reynolds number and find that in the non-rotating
case the unsteady solutions are chaotic, while not in the rotating cases
calculated. This result reflects the general tendency that the rotation
stabilizes nonlinear solutions of Navier-Stokes equations.
Abstract: Recently, the health of retired National Football
League players, particularly lineman has been investigated. A
number of studies have reported increased cardiometabolic risk,
premature cardiovascular disease and incidence of type 2 diabetes.
Rugby union players have somatotypes very similar to National
Football League players which suggests that rugby players may have
similar health risks. The International Golden Oldies World Rugby
Festival (GORF) provided a unique opportunity to investigate the
demographics of veteran rugby players. METHODOLOGIES: A
cross-sectional, observational study was completed using an online
web-based questionnaire that consisted of medical history and
physiological measures. Data analysis was completed using a one
sample t-test (50yrs) and Chi-square test. RESULTS:
A total of 216 veteran rugby competitors (response rate = 6.8%)
representing 10 countries, aged 35-72 yrs (mean 51.2, S.D. ±8.0),
participated in the online survey. As a group, the incidence of current
smokers was low at 8.8% (avg 72.4 cigs/wk) whilst the percentage
consuming alcohol was high (93.1% (avg 11.2 drinks/wk).
Competitors reported the following top six chronic
diseases/disorders; hypertension (18.6%), arthritis (OA/RA, 11.5%),
asthma (9.3%), hyperlipidemia (8.2%), diabetes (all types, 7.5%) and
gout (6%), there were significant differences between groups with
regard to cancer (all types) and migraines. When compared to the
Australian general population (Australian Bureau of Statistics data,
n=18,000), GORF competitors had a significantly lower incidence of
anxiety (p
Abstract: Energy consumption rate during the cooling process
of industrial glass tempering process is considerably high. In this
experimental study the effect of dimensionless jet to jet distance
(S/D) and jet to plate distance (H/D) on the cooling time have been
investigated. In the experiments 4 mm thick glass samples have been
used. Cooling unit consists of 16 mutually placed seamless aluminum
nozzles of 8 mm in diameter and 80 mm in length. Nozzles were in
staggered arrangement. Experiments were conducted with circular
jets for H/D values between 1 and 10, and for S/D values between 2
and 10. During the experiments Reynolds number has been kept
constant at 30000. Experimental results showed that the longest
cooling time with 87 seconds has been observed in the experiments
for S/D=10 and H/D=10 values, while the shortest cooling time with
42.5 seconds has been measured in the experiments for S/D=2 and
H/D=4 values.
Abstract: The current study has investigated the ageing
phenomena of silica optical fibres in relation to water activity which might be accelerated when exposed to a supplementary energy, such as microwaves. A controlled stress by winding fibres onto accurate
diameter mandrel was applied. Taking into account that normally a
decrease in fibre strength is induced in time by chemical action of water, the effects of cumulative reagents such as: water, applied stress and supplementary energy (microwave) in some cases acted in
the opposite manner. The microwave effect as a structural relaxation
catalyst appears unexpected, even if the overall gain in fibre strength is not high, but the stress corrosion factor revealed significant
increase in certain simulation conditions.
Abstract: Utilization of diverse germplasm is needed to enhance
the genetic diversity of cultivars. The objective of this study was to
evaluate the genetic relationships of 98 alfalfa germplasm accessions
using morphological traits and SSR markers. From the 98 tested
populations, 81 were locals originating in Europe, 17 were introduced
from USA, Australia, New Zealand and Canada. Three primers
generated 67 polymorphic bands. The average polymorphic
information content (PIC) was very high (> 0.90) over all three used
primer combinations. Cluster analysis using Unweighted Pair Group
Method with Arithmetic Means (UPGMA) and Jaccard´s coefficient
grouped the accessions into 2 major clusters with 4 sub-clusters with
no correlation between genetic and morphological diversity. The SSR
analysis clearly indicated that even with three polymorphic primers,
reliable estimation of genetic diversity could be obtained.
Abstract: Based on statistics released by Islamic Republic of
Iran Police (IRIP), from among the total 9555 motorcycle accidents
that happened in 2007, 857 riders died and 11219 one got injured. If
we also consider the death toll and injuries of other vehicles'
accidents resulted from traffic violation by motorcycle riders, then
paying attention to the motorcycle accidents seems to be very
necessary. Therefore, in this study we tried to investigate the traits
and issues related to production, application, and training, along with
causes of motorcycle accidents from 4 perspectives of road, human,
environment and vehicle and also based on statistical and
geographical analysis of accident-sheets prepared by Iran Road
Patrol Department (IRPD). Unfamiliarity of riders with regulations
and techniques of motorcycling, disuse of safety equipments,
inefficiency of roads and design of junctions for safe trafficking of
motorcycles and finally the lack of sufficient control of responsible
organizations are among the major causes which lead to these
accidents.
Abstract: Limited infrastructure development on peats and
organic soils is a serious geotechnical issues common to many
countries of the world especially Malaysia which distributed 1.5 mill
ha of those problematic soil. These soils have high water content and
organic content which exhibit different mechanical properties and
may also change chemically and biologically with time. Constructing
structures on peaty ground involves the risk of ground failure and
extreme settlement. Nowdays, much efforts need to be done in
making peatlands usable for construction due to increased landuse.
Deep mixing method employing cement as binders, is generally used
as measure again peaty/ organic ground failure problem. Where the
technique is widely adopted because it can improved ground
considerably in a short period of time. An understanding of
geotechnical properties as shear strength, stiffness and compressibility
behavior of these soils was requires before continues construction on
it. Therefore, 1- 1.5 meter peat soil sample from states of Johor and
an organic soil from Melaka, Malaysia were investigated. Cement
were added to the soil in the pre-mixing stage with water cement ratio
at range 3.5,7,14,140 for peats and 5,10,30 for organic soils,
essentially to modify the original soil textures and properties. The
mixtures which in slurry form will pour to polyvinyl chloride (pvc)
tube and cured at room temperature 250C for 7,14 and 28 days.
Laboratory experiments were conducted including unconfined
compressive strength and bender element , to monitor the improved
strength and stiffness of the 'stabilised mixed soils'. In between,
scanning electron miscroscopic (SEM) were observations to
investigate changes in microstructures of stabilised soils and to
evaluated hardening effect of a peat and organic soils stabilised
cement. This preliminary effort indicated that pre-mixing peat and
organic soils contributes in gaining soil strength while help the
engineers to establish a new method for those problematic ground
improvement in further practical and long term applications.
Abstract: The IFS is a scheme for describing and manipulating complex fractal attractors using simple mathematical models. More precisely, the most popular “fractal –based" algorithms for both representation and compression of computer images have involved some implementation of the method of Iterated Function Systems (IFS) on complete metric spaces. In this paper a new generalized space called Multi-Fuzzy Fractal Space was constructed. On these spases a distance function is defined, and its completeness is proved. The completeness property of this space ensures the existence of a fixed-point theorem for the family of continuous mappings. This theorem is the fundamental result on which the IFS methods are based and the fractals are built. The defined mappings are proved to satisfy some generalizations of the contraction condition.
Abstract: Evolvable hardware (EHW) is a developing field that
applies evolutionary algorithm (EA) to automatically design circuits,
antennas, robot controllers etc. A lot of research has been done in this
area and several different EAs have been introduced to tackle
numerous problems, as scalability, evolvability etc. However every
time a specific EA is chosen for solving a particular task, all its
components, such as population size, initialization, selection
mechanism, mutation rate, and genetic operators, should be selected
in order to achieve the best results. In the last three decade the
selection of the right parameters for the EA-s components for solving
different “test-problems" has been investigated. In this paper the
behaviour of mutation rate for designing logic circuits, which has not
been done before, has been deeply analyzed. The mutation rate for an
EHW system modifies the number of inputs of each logic gates, the
functionality (for example from AND to NOR) and the connectivity
between logic gates. The behaviour of the mutation has been
analyzed based on the number of generations, genotype redundancy
and number of logic gates for the evolved circuits. The experimental
results found provide the behaviour of the mutation rate during
evolution for the design and optimization of simple logic circuits.
The experimental results propose the best mutation rate to be used for
designing combinational logic circuits. The research presented is
particular important for those who would like to implement a
dynamic mutation rate inside the evolutionary algorithm for evolving
digital circuits. The researches on the mutation rate during the last 40
years are also summarized.
Abstract: Monitoring of microbial flora in aquacultured sea bream, in relation to the physicochemical parameters of the rearing seawater, ended to a model describing the influence of the last to the quality of the fisheries. Fishes were sampled during eight months from four aqua farms in Western Greece and analyzed for psychrotrophic, H2S producing bacteria, Salmonella sp., heterotrophic plate count (PCA), with simultaneous physical evaluation. Temperature, dissolved oxygen, pH, conductivity, TDS, salinity, NO3 - and NH4 + ions were recorded. Temperature, dissolved oxygen and conductivity were correlated, respectively, to PCA, Pseudomonas sp. and Shewanella sp. counts. These parameters were the inputs of the model, which was driving, as outputs, to the prediction of PCA, Vibrio sp., Pseudomonas sp. and Shewanella sp. counts, and fish microbiological quality. The present study provides, for the first time, a ready-to-use predictive model of fisheries hygiene, leading to an effective management system for the optimization of aquaculture fisheries quality.
Abstract: This paper proposes a zero-voltage transition (ZVT) PWM synchronous buck converter, which is designed to operate at low output voltage and high efficiency typically required for portable systems. To make the DC-DC converter efficient at lower voltage, synchronous converter is an obvious choice because of lower conduction loss in the diode. The high-side MOSFET is dominated by the switching losses and it is eliminated by the soft switching technique. Additionally, the resonant auxiliary circuit designed is also devoid of the switching losses. The suggested procedure ensures an efficient converter. Theoretical analysis, computer simulation, and experimental results are presented to explain the proposed schemes.
Abstract: Fault-proneness of a software module is the
probability that the module contains faults. To predict faultproneness
of modules different techniques have been proposed which
includes statistical methods, machine learning techniques, neural
network techniques and clustering techniques. The aim of proposed
study is to explore whether metrics available in the early lifecycle
(i.e. requirement metrics), metrics available in the late lifecycle (i.e.
code metrics) and metrics available in the early lifecycle (i.e.
requirement metrics) combined with metrics available in the late
lifecycle (i.e. code metrics) can be used to identify fault prone
modules using Genetic Algorithm technique. This approach has been
tested with real time defect C Programming language datasets of
NASA software projects. The results show that the fusion of
requirement and code metric is the best prediction model for
detecting the faults as compared with commonly used code based
model.
Abstract: Mushrooms are a group of fleshy macroscopic fungi.
They have been valued throughout the world as both edible and
medicine. They are highly nutritious with good amount of quality
proteins, vitamins and minerals. An edible mushroom, Calocybe
indica was selected to validate its nutritional and medicinal
properties. Since tissue damage in hyperglycemia has been related to
oxidative stress, we evaluated the enzymatic and non-enzymatic
antioxidant status in the serum, liver and kidney since they are the
target organs in diabetic complications. From the results, increased
oxidative stress and decreased antioxidants might be related to the
causation of diabetes mellitus. The treatment in the diabetic rats with
the Calocybe indica showed an increase in the antioxidant system
and decrease in the production of free radicals. The mushrooms
which contain antioxidant phytochemicals has potential free radical
scavenging capacity and hence can induce the antioxidant system in
the body significantly reduces the generated free radicals thereby
maintaining the normal levels of the antioxidants