Abstract: Operational safety of critical systems, such as nuclear power plants, industrial chemical processes and means of transportation, is a major concern for system engineers and operators. A means to assure that is on-line safety monitors that deliver three safety tasks; fault detection and diagnosis, alarm annunciation and fault controlling. While current monitors deliver these tasks, benefits and limitations in their approaches have at the same time been highlighted. Drawing from those benefits, this paper develops a distributed monitor based on semi-independent agents, i.e. a multiagent system, and monitoring knowledge derived from a safety assessment model of the monitored system. Agents are deployed hierarchically and provided with knowledge portions and collaboration protocols to reason and integrate over the operational conditions of the components of the monitored system. The monitor aims to address limitations arising from the large-scale, complicated behaviour and distributed nature of monitored systems and deliver the aforementioned three monitoring tasks effectively.
Abstract: The IEEE802.16 standard which has emerged as
Broadband Wireless Access (BWA) technology, promises to deliver
high data rate over large areas to a large number of subscribers in the
near future. This paper analyze the effect of overheads over capacity
of downlink (DL) of orthogonal frequency division multiple access
(OFDMA)–based on the IEEE802.16e mobile WiMAX system with
and without overheads. The analysis focuses in particular on the
impact of Adaptive Modulation and Coding (AMC) as well as
deriving an algorithm to determine the maximum numbers of
subscribers that each specific WiMAX sector may support. An
analytical study of the WiMAX propagation channel by using Cost-
231 Hata Model is presented. Numerical results and discussion
estimated by using Matlab to simulate the algorithm for different
multi-users parameters.
Abstract: We have fabricated a-IGZO TFT and investigated the
stability under positive DC and AC bias stress. The threshold voltage
of a-IGZO TFT shifts positively under those biases, and that reduces
on-current. For this reason, conventional shift-register circuit
employing TFTs which stressed by positive bias will be unstable, may
do not work properly. We have designed a new 6-transistor
shift-register, which has less transistors than prior circuits. The TFTs
of the proposed shift-register are not suffering from positive DC or AC
stress, mainly kept unbiased. Despite the compact design, the stable
output signal was verified through the SPICE simulation even under
RC delay of clock signal.
Abstract: Flexible manufacturing system is a system that is able to respond to changed conditions. In general, this flexibility is divided into two key categories and several subcategories. The first category is the so called machine flexibility which enables to make various products by the given machinery. The second category is routing flexibility enabling to execute the same operation by various machines. Flexible manufacturing systems usually consist of three main parts: CNC machine tools, transport system and control system. A higher level of flexible manufacturing systems is represented by the so called intelligent manufacturing systems.
Abstract: The implementation of the new software and hardware-s technologies for tritium processing nuclear plants, and especially those with an experimental character or of new technology developments shows a coefficient of complexity due to issues raised by the implementation of the performing instrumentation and equipment into a unitary monitoring system of the nuclear technological process of tritium removal. Keeping the system-s flexibility is a demand of the nuclear experimental plants for which the change of configuration, process and parameters is something usual. The big amount of data that needs to be processed stored and accessed for real time simulation and optimization demands the achievement of the virtual technologic platform where the data acquiring, control and analysis systems of the technological process can be integrated with a developed technological monitoring system. Thus, integrated computing and monitoring systems needed for the supervising of the technological process will be executed, to be continued with the execution of optimization system, by choosing new and performed methods corresponding to the technological processes within the tritium removal processing nuclear plants. The developing software applications is executed with the support of the program packages dedicated to industrial processes and they will include acquisition and monitoring sub-modules, named “virtually" as well as the storage sub-module of the process data later required for the software of optimization and simulation of the technological process for tritium removal. The system plays and important role in the environment protection and durable development through new technologies, that is – the reduction of and fight against industrial accidents in the case of tritium processing nuclear plants. Research for monitoring optimisation of nuclear processes is also a major driving force for economic and social development.
Abstract: Tomato nutrition value, color, flavor of their fruits and products depends mainly on lycopene, β-carotene, ascorbic acid, sugars and their ratio. The two most important carotenoids in fruits of tomato are lycopene, which determined fruits red color, and β- carotene, which accounts for approximately 7% of the tomato carotenoids. Therefore, tomato products and their quality can be well characterized by the content of these elements.Maturity at harvest is very important to composition and quality of tomatoes. This is especially a problem with tomatoes picked green since it is difficult to differentiate between mature and immature-green fruits. Typical and advanced mature-green tomatoes will usually attain a much better flavor than those picked at the immature or partially mature stages.To better understand the synthesis of biochemical compounds, their concentration should be compared not only at the last stage of maturity, but also during all fruit ripening period in different varieties.
Abstract: GFRG(Glass Fiber Reinforced Gypsum) wall is a green product which can erect a building fast in prefabricated method, but its application to high-rise residential buildings is limited for its poor lateral stiffness. This paper has proposed a modification to GFRG walls structure to increase its lateral stiffness, which aiming to erect small high-rise residential buildings as load-bearing walls. The elastic finite element analysis to it has shown the lateral deformation feature and the distributions of the axial force and the shear force. The analysis results show that the new GFRG reinforced concrete wall can be used for small high-rise residential buildings.
Abstract: This paper investigates vortex shedding processes
occurring at the end of a stack of parallel plates, due to an oscillating
flow induced by an acoustic standing wave within an acoustic
resonator. Here, Particle Image Velocimetry (PIV) is used to quantify
the vortex shedding processes within an acoustic cycle
phase-by-phase, in particular during the “ejection" of the fluid out of
the stack. Standard hot-wire anemometry measurement is also applied
to detect the velocity fluctuations near the end of the stack.
Combination of these two measurement techniques allowed a detailed
analysis of the vortex shedding phenomena. The results obtained show
that, as the Reynolds number varies (by varying the plate thickness
and drive ratio), different flow patterns of vortex shedding are
observed by the PIV measurement. On the other hand, the
time-dependent hot-wire measurements allow obtaining detailed
frequency spectra of the velocity signal, used for calculating
characteristic Strouhal numbers. The impact of the plate thickness and
the Reynolds number on the vortex shedding pattern has been
discussed. Furthermore, a detailed map of the relationship between the
Strouhal number and Reynolds number has been obtained and
discussed.
Abstract: KSLV-I(Korea Space Launch Vehicle-I) is designed as
a launch vehicle to enter a 100 kg-class satellite to the LEO(Low Earth
Orbit). Attitude angles of the upper-stage, including roll, pitch and
yaw are controlled by the cold gas thruster system using nitrogen gas.
The cold gas thruster is an actuator in the RCS(Reaction Control
System). To design an attitude controller for the upper-stage, thrust
measurement in vacuum condition is required. In this paper, the new
thrust measurement system and calibration mechanism are developed
and measurement errors and signal processing method are presented.
Abstract: Power systems and transformer are intrinsic apparatus, therefore its reliability and safe operation is important to determine their operation conditions, and the industry uses quality control tests in the insulation design of oil filled transformers. Hence the service period effect on AC dielectric strength is significant. The effect of aging on transformer oil physical, chemical and electrical properties was studied using the international testing methods for the evaluation of transformer oil quality. The study was carried out on six transformers operate in the field and for monitoring periods over twenty years. The properties which are strongly time dependent were specified and those which have a great impact on the transformer oil acidity, breakdown voltage and dissolved gas analysis were defined. Several tests on the transformers oil were studied to know the time of purifying or changing it, moreover prediction of the characteristics of it under different operation conditions.
Abstract: The activities which are mostly related to the environmental performance need to be pointed, especially how logistics systems influence on environmental performance. This paper analyses how company could lead the initiative in this area by incorporating environmental management principles into their daily activities. The analysis is based on literature review about logistics and environment, the information from company R website as well as face-to-face interviews. A case study is given to show how they can turn practices into green while simultaneously meet the efficiency objectives. The research results show that the adoption of EMS and ISO 14001 certification is an effective tool for the logistics management. Such practices simultaneously reduce the negative contribute to better company performance. The results also show that the emissions to air and water, and energy consumption are the main logistics impacts to the environment.
Abstract: This paper presents an experimental investigation of
transformer dielectric response and solid insulation water content.
The dielectric response was carried out on the base of Hybrid
Frequency Dielectric Spectroscopy and Polarization Current
measurements method (FDS &PC). The calculation of the water
content in paper is based on the water content in oil and the obtained
equilibrium curves. A reference measurements were performed at
equilibrium conditions for water content in oil and paper of
transformer at different stable temperatures (25, 50, 60 and 70°C) to
prepare references to evaluate the insulation behavior at the not
equilibrium conditions. Some measurements performed at the
different simulated normal working modes of transformer operation
at the same temperature where the equilibrium conditions. The
obtained results show that when transformer temperature is mach
more than the its ambient temperature, the transformer temperature
decreases immediately after disconnecting the transformer from the
network and this temperature reduction influences the transformer
insulation condition in the measuring process. In addition to the oil
temperature at the near places to the sensors, the temperature
uniformity in transformer which can be changed by a big change in
the load of transformer before the measuring time will influence the
result. The investigations have shown that the extremely influence of
the time between disconnecting the transformer and beginning the
measurements on the results. And the online monitoring for water
content in paper measurements, on the basis of the oil water content
on line monitoring and the obtained equilibrium curves. The
measurements where performed continuously and for about 50 days
without any disconnection in the prepared the adiabatic room.
Abstract: This paper presents the development of a software
application for Off-line robot task programming and simulation. Such
application is designed to assist in robot task planning and to direct
manipulator motion on sensor based programmed motion. The
concept of the designed programming application is to use the power
of the knowledge base for task accumulation. In support of the
programming means, an interactive graphical simulation for
manipulator kinematics was also developed and integrated into the
application as the complimentary factor to the robot programming
media. The simulation provides the designer with useful,
inexpensive, off-line tools for retain and testing robotics work cells
and automated assembly lines for various industrial applications.
Abstract: In this paper, the deformation modes of a compact impact absorption member subjected to axial compression are investigated using finite element method and experiments. A multiple combination compact impact absorption member, referred to as a 'compress-expand member', is proposed to substitute the conventional thin-walled circular tube. This study found that the proposed compact impact absorption member has stable load increase characteristics and a wider range of high load efficiency (Pave/Pmax) than the thin-walled circular tube. Moreover, the proposed compact impact absorption member can absorb larger loads in a smaller radius than the thin-walled cylindrical tube, as it can maintain its stable deformation in increased wall thicknesses.
Abstract: The expansion mechanism of a partially ionized plasma produced by laser interaction with solid target (copper) is studied. For this purpose we use a hydrodynamical model which includes a source term combined with Saha's equation. The obtained self-similar solution in the limit of quasi-neutrality shows that the expansion, at the earlier stage, is driven by the combination of thermal pressure and electrostatic potential. They are of the same magnitude. The initial ionized fraction and the temperature are the leading parameters of the expanding profiles,
Abstract: Recent widespread use of information and
communication technology has greatly changed information security
risks that businesses and institutions encounter. Along with this
situation, in order to ensure security and have confidence in electronic
trading, it has become important for organizations to take competent
information security measures to provide international confidence that
sensitive information is secure. Against this backdrop, the approach to
information security checking has come to an important issue, which
is believed to be common to all countries. The purpose of this paper is
to introduce the new system of information security checking program
in Korea and to propose synthetic information security
countermeasures under domestic circumstances in order to protect
physical equipment, security management and technology, and the
operation of security check for securing services on ISP(Internet
Service Provider), IDC(Internet Data Center), and
e-commerce(shopping malls, etc.)
Abstract: In this paper a novel method for finding the fault zone
on a Thyristor Controlled Series Capacitor (TCSC) incorporated
transmission line is presented. The method makes use of the Support
Vector Machine (SVM), used in the classification mode to
distinguish between the zones, before or after the TCSC. The use of
Discrete Wavelet Transform is made to prepare the features which
would be given as the input to the SVM. This method was tested on a
400 kV, 50 Hz, 300 Km transmission line and the results were highly
accurate.
Abstract: In construction of any structure, the aesthetic and utility values should be considered in such a way as to make the structure cost-effective. Most structures are composed of elements and joints which are very critical in any skeletal space structure because they majorly determine the performance of the structure. In early times, most space structures were constructed using rigid joints which had the advantage of better performing structures as compared to pin-jointed structures but with the disadvantage of requiring all the construction work to be done on site. The discovery of semi-rigid joints now enables connections to be prefabricated and quickly assembled on site while maintaining good performance. In this paper, cost-effective is discussed basing on strength of connectors at the joints, buckling of joints and overall structure, and the effect of initial geometrical imperfections. Several existing joints are reviewed by classifying them into categories and discussing where they are most suited and how they perform structurally. Also, finite element modeling using ABAQUS is done to determine the buckling behavior. It is observed that some joints are more economical than others. The rise to span ratio and imperfections are also found to affect the buckling of the structures. Based on these, general principles that guide the design of cost-effective joints and structures are discussed.
Abstract: Pattern recognition is the research area of Artificial
Intelligence that studies the operation and design of systems that
recognize patterns in the data. Important application areas are image
analysis, character recognition, fingerprint classification, speech
analysis, DNA sequence identification, man and machine
diagnostics, person identification and industrial inspection. The
interest in improving the classification systems of data analysis is
independent from the context of applications. In fact, in many
studies it is often the case to have to recognize and to distinguish
groups of various objects, which requires the need for valid
instruments capable to perform this task. The objective of this article
is to show several methodologies of Artificial Intelligence for data
classification applied to biomedical patterns. In particular, this work
deals with the realization of a Computer-Aided Detection system
(CADe) that is able to assist the radiologist in identifying types of
mammary tumor lesions. As an additional biomedical application of
the classification systems, we present a study conducted on blood
samples which shows how these methods may help to distinguish
between carriers of Thalassemia (or Mediterranean Anaemia) and
healthy subjects.
Abstract: It is established that the instantaneous heart rate (HR) of healthy humans keeps on changing. Analysis of heart rate variability (HRV) has become a popular non invasive tool for assessing the activities of autonomic nervous system. Depressed HRV has been found in several disorders, like diabetes mellitus (DM) and coronary artery disease, characterised by autonomic nervous dysfunction. A new technique, which searches for pattern repeatability in a time series, is proposed specifically for the analysis of heart rate data. These set of indices, which are termed as pattern repeatability measure and pattern repeatability ratio are compared with approximate entropy and sample entropy. In our analysis, based on the method developed, it is observed that heart rate variability is significantly different for DM patients, particularly for patients with diabetic foot ulcer.