Abstract: Particle damping is a technique to reduce the
structural vibrations by means of placing small metallic particles
inside a cavity that is attached to the structure at location of high
vibration amplitudes. In this paper, we have presented an analytical
model to simulate the particle damping of two dimensional transient
vibrations in structure operating under high centrifugal loads. The
simulation results show that this technique remains effective as long
as the ratio of the dynamic acceleration of the structure to the applied
centrifugal load is more than 0.1. Particle damping increases with the
increase of particle to structure mass ratio. However, unlike to the
case of particle damping in the absence of centrifugal loads where
the damping efficiency strongly depends upon the size of the cavity,
here this dependence becomes very weak. Despite the simplicity of
the model, the simulation results are considerably in good agreement
with the very scarce experimental data available in the literature for
particle damping under centrifugal loads.
Abstract: This study presents design of a carbon silicon electrode
for iontophorsis treatment towards alopecia. The alopecia is a medical
description means loss of hair from the body. For solving this problem,
the drug need to be delivered into the scalp, therefore, the
iontophoresis was chosen to use in this treatment. However, almost
common electrodes of iontophoresis device are made with metal
material, the electrodes could give patients hurt when they using it, and
it is hard to avoid the hair for attaching the hair. For this reason, an
electrode is made with silicon material to decrease the hurt from the
electrodes, and the carbon material is mixed in it for increasing
conductance. The several cones with stainless material on the
electrode make the electrode is able to void hair to attach the affected
part. According to the results of a vivo-experiment, the carbon silicon
electrode showed a good performance and in treatment comfortably.
Abstract: In this work, sorption of nickel from aqueous solution on hypnea valentiae, red macro algae, was investigated. Batch experiments have been carried out to find the effect of various parameters such as pH, temperature, sorbent dosage, metal concentration and contact time on the sorption of nickel using hypnea valentiae. Response surface methodology (RSM) is employed to optimize the process parameters. Based on the central composite design, quadratic model was developed to correlate the process variables to the response. The most influential factor on each experimental design response was identified from the analysis of variance (ANOVA). The optimum conditions for the sorption of nickel were found to be: pH – 5.1, temperature – 36.8oC, sorbent dosage – 5.1 g/L, metal concentration – 100 mg/L and contact time – 30 min. At these optimized conditions the maximum removal of nickel was found to be 91.97%. A coefficient of determination R2 value 0.9548 shows the fitness of response surface methodology in this work.
Abstract: In this study we present the effect of elevated
temperatures from 300K to 400K on the electrical properties of
copper Phthalocyanine (CuPc) based organic field effect transistors
(OFET). Thin films of organic semiconductor CuPc (40nm) and
semitransparent Al (20nm) were deposited in sequence, by vacuum
evaporation on a glass substrate with previously deposited Ag source
and drain electrodes with a gap of 40 μm. Under resistive mode of
operation, where gate was suspended it was observed that drain
current of this organic field effect transistor (OFET) show an
increase with temperature. While in grounded gate condition metal
(aluminum) – semiconductor (Copper Phthalocyanine) Schottky
junction dominated the output characteristics and device showed
switching effect from low to high conduction states like Zener diode
at higher bias voltages. This threshold voltage for switching effect
has been found to be inversely proportional to temperature and shows
an abrupt decrease after knee temperature of 360K. Change in
dynamic resistance (Rd = dV/dI) with respect to temperature was
observed to be -1%/K.
Abstract: Mycophenolic acid (MPA) is a secondary metabolite
produced by Penicillium brevicompactum, which has antibiotic and
immunosuppressive properties. In this study, the first, mycophenolic
acid was produced in a fermentation process by Penicillium
brevicompactum MUCL 19011 in shake flask using a base medium.
The maximum MPA production, product yield and productivity of
process were 1.379 g/L, 18.6 mg/g glucose and 4.9 mg/L. h,
respectively. Also the glucose consumption, biomass and MPA
production profiles were investigated during batch cultivation.
Obtained results showed that MPA production starts approximately
after 180 hours and reaches to a maximum at 280 h. In the next step,
the effects of some various concentrations of enzymatically
hydrolyzed casein on MPA production were evaluated. Maximum
MPA production, product yield and productivity as 3.63 g/L, 49
mg/g glucose and 12.96 mg/L.h, respectively were obtained with
using 30 g/L enzymatically hydrolyzed casein in culture medium.
These values show an enhanced MPA production, product yield and
process productivity pr as 116.8%, 132.8% and 163.2%, respectively.
Abstract: Measuring the effect of perinatal lead exposure on learning ability of offspring is considered as a sensitive and selective index for providing an early marker for central nervous system damage produced by this toxic metal. A total of 35 Sprague-Dawley adult rats were used to investigate the effect of lead acetate toxicity on behavioral patterns of adult female rats and learning ability of offspring. Rats were allotted into 4 groups, group one received 1g/l lead acetate (n=10), group two received 1.5g/l lead acetate (n=10), group three received 2g/l lead acetate in drinking water (n=10) and control group did not receive lead acetate (n=5) from 8th day of pregnancy till weaning of pups.
The obtained results revealed a dose dependent increase in the feeding time, drinking frequency, licking frequency, scratching frequency, licking litters, nest building and retrieving frequencies, while standing time increased significantly in rats treated with 1.5g/l lead acetate than other treated groups and control, on contrary lying time decreased gradually in a dose dependent manner. Moreover, movement activities were higher in rats treated with 1g/l lead acetate than other treated groups and control. Furthermore, time spent in closed arms was significantly lower in rats given 2g/l lead acetate than other treated groups, while, they spent significantly much time spent in open arms than other treated groups which could be attributed to occurrence of adaptation. Furthermore, number of entries in open arms was dose dependent. However, the ratio between open/closed arms revealed a significant decrease in rats treated with 2g/l lead acetate than control group.
Abstract: Integrins are a large family of multidomain α/β cell
signaling receptors. Some integrins contain an additional inserted I
domain, whose earliest expression appears to be with the chordates,
since they are observed in the urochordates Ciona intestinalis (vase
tunicate) and Halocynthia roretzi (sea pineapple), but not in integrins
of earlier diverging species. The domain-s presence is viewed as a
hallmark of integrins of higher metazoans, however in vertebrates,
there are clearly three structurally-different classes: integrins without
I domains, and two groups of integrins with I domains but separable
by the presence or absence of an additional αC helix. For example,
the αI domains in collagen-binding integrins from Osteichthyes
(bony fish) and all higher vertebrates contain the specific αC helix,
whereas the αI domains in non-collagen binding integrins from
vertebrates and the αI domains from earlier diverging urochordate
integrins, i.e. tunicates, do not. Unfortunately, within the early
chordates, there is an evolutionary gap due to extinctions between the
tunicates and cartilaginous fish. This, coupled with a knowledge gap
due to the lack of complete genomic data from surviving species,
means that the origin of collagen-binding αC-containing αI domains
remains unknown. Here, we analyzed two available genomes from
Callorhinchus milii (ghost shark/elephant shark; Chondrichthyes –
cartilaginous fish) and Petromyzon marinus (sea lamprey;
Agnathostomata), and several available Expression Sequence Tags
from two Chondrichthyes species: Raja erinacea (little skate) and
Squalus acanthias (dogfish shark); and Eptatretus burgeri (inshore
hagfish; Agnathostomata), which evolutionary reside between the
urochordates and osteichthyes. In P. marinus, we observed several
fragments coding for the αC-containing αI domain, allowing us to
shed more light on the evolution of the collagen-binding integrins.
Abstract: Recently, most digital systems are designed as GALS (Globally Asynchronous Locally Synchronous) systems. Several architectures have been proposed as bus architectures for a GALS system : shared bus, segmented bus, ring bus, and so on. In this study, we propose a ring segmented bus architecture which is a combination of segmented bus and ring bus architecture with the aim of throughput enhancement. In a segmented bus architecture, segments are connected in series. By connecting the segments at the end of the bus and constructing the ring bus, it becomes possible to allocate a channel of the bus bidirectionally. The bus channel is allocated to the shortest path between segments. We consider a metastable operation caused by asynchronous communication between segments and a burst transfer between segments. According to the result of simulation, it is shown that the GALS system designed by the proposed method has the desired operations.
Abstract: Slag sample from copper smelting operation in a
water jacket furnace from DRC plant was used. The study intends to
determine the effect of cooling in the extraction of base metals. The
cooling methods investigated were water quenching, air cooling and
furnace cooling. The latter cooling ways were compared to the
original as received slag. It was observed that, the cooling rate of the
slag affected the leaching of base metals as it changed the phase
distribution in the slag and the base metals distribution within the
phases. It was also found that fast cooling of slag prevented
crystallization and produced an amorphous phase that encloses the
base metals. The amorphous slags from the slag dumps were more
leachable in acidic medium (HNO3) which leached 46%Cu, 95% Co,
85% Zn, 92% Pb and 79% Fe with no selectivity at pH0, than in
basic medium (NH4OH). The leachability was vice versa for the
modified slags by quenching in water which leached 89%Cu with a
high selectivity as metal extractions are less than 1% for Co, Zn, Pb
and Fe at ambient temperature and pH12. For the crystallized slags,
leaching of base metals increased with the increase of temperature
from ambient temperature to 60°C and decreased at the higher
temperature of 80°C due to the evaporation of the ammonia solution
used for basic leaching, the total amounts of base metals that were
leached in slow cooled slags were very low compared to the
quenched slag samples.
Abstract: Heavy metal transfer in soil profiles is a major
environmental concern because even slow transport through the soil
may eventually lead to deterioration of groundwater quality. The use
of sewage sludge and effluents from wastewater treatment plants for
irrigation of agricultural lands is on the rise particularly in peri-urban
area of developing countries. In this study soil samples under sludge
application and wastewater irrigation were studied and soil samples
were collected in the soil profiles from the surface to 100 cm in
depth. For this purpose, three plots were made in a treatment plant in
south of Tehran-Iran. First plot was irrigated just with effluent from
wastewater treatment plant, second plot with simulated heavy metals
concentration equal 50 years irrigation and in third plot sewage
sludge and effluent was used. Trace metals concentration (Cd, Cu)
were determined for soil samples. The results indicate movement of
metals was observed, but the most concentration of metals was found
in topsoil samples. The most of Cadmium concentration was
measured in the topsoil of plot 3, 4.5mg/kg and Maximum cadmium
movement was observed in 0-20 cm. The most concentration of
copper was 27.76mg/kg, and maximum percolation in 0-20 cm.
Metals (Cd, Cu) were measured in leached water. Preferential flow
and metal complexation with soluble organic apparently allow
leaching of heavy metals.
Abstract: Microplasma welding is a less expensive alternative to
laser welding in dental technology. The aim of the study was to
highlight discontinuities present in the microplasma welded joints of
dental base metal alloys by visual analysis. Five base metal alloys
designated for fixed prostheses manufacture were selected for the
experiments. Using these plates, preliminary tests were conducted by
microplasma welding in butt joint configuration, without filler
material, bilaterally and with filler material, proper for each base
metal. Macroscopic visual inspection was performed to assess
carefully the irregularities in the welds. Electron microscopy allowed
detection of discontinuities that are not visible to the eye and
revealing details regarding location, trajectory, morphology and size
of discontinuities. Supplementing visual control with microscopic
analysis allows to detect small discontinuities, which escapes the
macroscopic control and to make a detailed study of the weld.
Abstract: The most important property of the Gene Ontology is
the terms. These control vocabularies are defined to provide
consistent descriptions of gene products that are shareable and
computationally accessible by humans, software agent, or other
machine-readable meta-data. Each term is associated with
information such as definition, synonyms, database references, amino
acid sequences, and relationships to other terms. This information has
made the Gene Ontology broadly applied in microarray and
proteomic analysis. However, the process of searching the terms is
still carried out using traditional approach which is based on keyword
matching. The weaknesses of this approach are: ignoring semantic
relationships between terms, and highly depending on a specialist to
find similar terms. Therefore, this study combines semantic similarity
measure and genetic algorithm to perform a better retrieval process
for searching semantically similar terms. The semantic similarity
measure is used to compute similitude strength between two terms.
Then, the genetic algorithm is employed to perform batch retrievals
and to handle the situation of the large search space of the Gene
Ontology graph. The computational results are presented to show the
effectiveness of the proposed algorithm.
Abstract: This paper presents an algorithm of particle swarm
optimization with reduction for global optimization problems. Particle
swarm optimization is an algorithm which refers to the collective
motion such as birds or fishes, and a multi-point search algorithm
which finds a best solution using multiple particles. Particle
swarm optimization is so flexible that it can adapt to a number
of optimization problems. When an objective function has a lot of
local minimums complicatedly, the particle may fall into a local
minimum. For avoiding the local minimum, a number of particles are
initially prepared and their positions are updated by particle swarm
optimization. Particles sequentially reduce to reach a predetermined
number of them grounded in evaluation value and particle swarm
optimization continues until the termination condition is met. In order
to show the effectiveness of the proposed algorithm, we examine the
minimum by using test functions compared to existing algorithms.
Furthermore the influence of best value on the initial number of
particles for our algorithm is discussed.
Abstract: Here we have considered non uniform microstrip
leaky-wave antenna implemented on a dielectric waveguide by a
sinusoidal profile of periodic metallic grating. The non distribution of
the attenuation constant α along propagation axis, optimize the
radiating characteristics and performances of such antennas. The
method developped here is based on an integral method where the
formalism of the admittance operator is combined to a BKW
approximation. First, the effect of the modeling in the modal analysis
of complex waves is studied in detail. Then, the BKW model is used
for the dispersion analysis of the antenna of interest. According to
antenna theory, a forced continuity of the leaky-wave magnitude at
discontinuities of the non uniform structure is established. To test the
validity of our dispersion analysis, computed radiation patterns are
presented and compared in the millimeter band.
Abstract: The ability of agricultural and decorative plants to
absorb and detoxify TNT and RDX has been studied. All tested 8
plants, grown hydroponically, were able to absorb these explosives
from water solutions: Alfalfa > Soybean > Chickpea> Chikling vetch
>Ryegrass > Mung bean> China bean > Maize. Differently from
TNT, RDX did not exhibit negative influence on seed germination
and plant growth. Moreover, some plants, exposed to RDX
containing solution were increased in their biomass by 20%. Study of
the fate of absorbed [1-14ðí]-TNT revealed the label distribution in
low and high-molecular mass compounds, both in roots and above
ground parts of plants, prevailing in the later. Content of 14ðí in lowmolecular
compounds in plant roots are much higher than in above
ground parts. On the contrary, high-molecular compounds are more
intensively labeled in aboveground parts of soybean. Most part (up to
70%) of metabolites of TNT, formed either by enzymatic reduction
or oxidation, is found in high molecular insoluble conjugates.
Activation of enzymes, responsible for reduction, oxidation and
conjugation of TNT, such as nitroreductase, peroxidase,
phenoloxidase and glutathione S-transferase has been demonstrated.
Among these enzymes, only nitroreductase was shown to be induced
in alfalfa, exposed to RDX. The increase in malate dehydrogenase
activities in plants, exposed to both explosives, indicates
intensification of Tricarboxylic Acid Cycle, that generates reduced
equivalents of NAD(P)H, necessary for functioning of the
nitroreductase. The hypothetic scheme of TNT metabolism in plants
is proposed.
Abstract: Structured catalysts formed from the growth of
zeolites on substrates is an area of increasing interest due to the
increased efficiency of the catalytic process, and the ability to
provide superior heat transfer and thermal conductivity for both
exothermic and endothermic processes.
However, the generation of structured catalysts represents a
significant challenge when balancing the relationship variables
between materials properties and catalytic performance, with the
Na2O, H2O and Al2O3 gel composition paying a significant role in
this dynamic, thereby affecting the both the type and range of
application.
The structured catalyst films generated as part of this
investigation have been characterised using a range of techniques,
including X-ray diffraction (XRD), Electron microscopy (SEM),
Energy Dispersive X-ray analysis (EDX) and Thermogravimetric
Analysis (TGA), with the transition from oxide-on-alloy wires to
hydrothermally synthesised uniformly zeolite coated surfaces being
demonstrated using both SEM and XRD. The robustness of the
coatings has been ascertained by subjecting these to thermal cycling
(ambient to 550oC), with the results indicating that the synthesis time
and gel compositions have a crucial effect on the quality of zeolite
growth on the FeCrAlloy wires.
Finally, the activity of the structured catalyst was verified by a
series of comparison experiments with standard zeolite Y catalysts in
powdered pelleted forms.
Abstract: A lot of research has been done in the past decade in the field of audio content analysis for extracting various information from audio signal. One such significant information is the "perceived mood" or the "emotions" related to a music or audio clip. This information is extremely useful in applications like creating or adapting the play-list based on the mood of the listener. This information could also be helpful in better classification of the music database. In this paper we have presented a method to classify music not just based on the meta-data of the audio clip but also include the "mood" factor to help improve the music classification. We propose an automated and efficient way of classifying music samples based on the mood detection from the audio data. We in particular try to classify the music based on mood for Indian bollywood music. The proposed method tries to address the following problem statement: Genre information (usually part of the audio meta-data) alone does not help in better music classification. For example the acoustic version of the song "nothing else matters by Metallica" can be classified as melody music and thereby a person in relaxing or chill out mood might want to listen to this track. But more often than not this track is associated with metal / heavy rock genre and if a listener classified his play-list based on the genre information alone for his current mood, the user shall miss out on listening to this track. Currently methods exist to detect mood in western or similar kind of music. Our paper tries to solve the issue for Indian bollywood music from an Indian cultural context
Abstract: In this paper, we summarize recent work of the authors on nanocomputing memory devices. We investigate two memory devices, each comprising a charged metallofullerene and carbon nanotubes. The first device involves two open nanotubes of the same radius that are joined by a centrally located nanotube of a smaller radius. A metallofullerene is then enclosed inside the structure. The second device also involves a etallofullerene that is located inside a closed carbon nanotube. Assuming the Lennard-Jones interaction energy and the continuum approximation, for both devices, the metallofullerene has two symmetrically placed equal minimum energy positions. On one side the metallofullerene represents the zero information state and by applying an external electrical field, it can overcome the energy barrier, and pass from one end of the tube to the other, where the metallofullerene then represents the one information state.
Abstract: A procedure commonly used in Job Shop Scheduling Problem (JSSP) to evaluate the neighborhoods functions that use the non-deterministic algorithms is the calculation of the critical path in a digraph. This paper presents an experimental study of the cost of computation that exists when the calculation of the critical path in the solution for instances in which a JSSP of large size is involved. The results indicate that if the critical path is use in order to generate neighborhoods in the meta-heuristics that are used in JSSP, an elevated cost of computation exists in spite of the fact that the calculation of the critical path in any digraph is of polynomial complexity.
Abstract: The paper discusses optimising work on a method of processing ceramic / metal composite coatings for various applications and is based on preliminary work on processing anodes for solid oxide fuel cells (SOFCs). The composite coating is manufactured by the electroless co-deposition of nickel and yttria stabilised zirconia (YSZ) simultaneously on to a ceramic substrate. The effect on coating characteristics of substrate surface treatments and electroless nickel bath parameters such as pH and agitation methods are also investigated. Characterisation of the resulting deposit by scanning electron microscopy (SEM) and energy dispersive X-ray analysis (EDXA) is also discussed.