Abstract: Since columns are the most important elements of the
structures, failure of one column in a critical location can cause a
progressive collapse. In this respect, the repair and strengthening of
columns is a very important subject to reduce the building failure and
to keep the columns capacity. Twenty columns with different
parameters is tested and analysis. Eleven typical confined reinforced
concrete (RC) columns with different types of techniques are
assessment. And also, four confined concrete columns with plastic
tube (PVC) are tested with and with four paralleling tested of
unconfined plain concrete. The techniques of confined RC columns
are mortar strengthening, Steel rings strengthening, FRP
strengthening. Moreover, the technique of confined plain concrete
(PC) column is used PVC tubes. The columns are tested under
uniaxial compressive loads studied the effect of confinement on the
structural behavior of circular RC columns. Test results for each
column are presented in the form of crack patterns, stress-strain
curves. Test results show that confining of the RC columns using
different techniques of strengthening results significant improvement
of the general behavior of the columns and can used in construction.
And also, tested confined PC columns with PVC tubes results shown
that the confined PC with PVC tubes can be used in economical
building. The theoretical model for predicted column capacity is
founded with experimental factor depends on the confined techniques
used and the strain reduction.
Abstract: Stator elements «Vane diffuser + crossover + return
channel» of stages with different specific speed were investigated by
CFD calculations. The regime parameter was introduced to present
efficiency and loss coefficient performance of all elements together.
Flow structure demonstrated advantages and disadvantages of design.
Flow separation in crossovers was eliminated by its shape
modification. Efficiency increased visibly. Calculated CFD
performances are in acceptable correlation with predicted ones by
engineering design method. The information obtained is useful for
design method better calibration.
Abstract: A compact UWB planar antenna fed with a
microstrip-line is proposed. The new design consist of a rectangular
patch with symmetric l-shaped slots and fed by 50 Ω microstrip
transmission line and a reduced ground-plane which have a periodic
slots with an overall size of 47 mm x 20 mm. It is intended to be used
in wireless applications that cover the ultra-wideband (UWB)
frequency band. A wider impedance bandwidth of around 116.5%
(1.875 – 7.115 GHz) with stable radiation pattern is achieved. The
proposed antenna has excellent characteristics, low profile and costeffective
compared to existing UWB antennas. The UWB antenna is
designed and analyzed using CST Microwave Studio in transient
mode to verify antenna parameters improvements.
Abstract: The use of information tools is a common activity for
students of any educational stage when they encounter online
learning activities. Finding the relevant information for particular
learning tasks is the topic of this paper as it investigates the use of
information tools for a group of student participants. The paper
describes and discusses the results with particular implications for
use in higher education, and the findings suggest that improvement in
assessment design and subsequent student learning may be achieved
by structuring the purposefulness of information tools usage and
online reading behaviors of university students.
Abstract: Waste silicon carbide (waste SiC) filled high-density
polyethylene (HDPE) with and without surface modifiers were
studied. Two types of surface modifiers namely; high-density
polyethylene-grafted-maleic anhydride (HDPE-g-MA) and 3-aminopropyltriethoxysilane have been used in this study. The
composites were produced using a two roll mill, extruder and shaped
in a hydraulic compression molding machine. The mechanical
properties of polymer composites such as flexural strength and
modulus, impact strength, tensile strength, stiffness and hardness
were investigated over a range of compositions. It was found that,
flexural strength and modulus, tensile modulus and hardness
increased, whereas impact strength and tensile strength decreased
with the increasing in filler contents, compared to the neat HDPE. At
similar filler content, the effect of both surface modifiers increased
flexural modulus, impact strength, tensile strength and stiffness but
reduced the flexural strength. Morphological investigation using
SEM revealed that the improvement in mechanical properties was
due to enhancement of the interfacial adhesion between waste SiC
and HDPE.
Abstract: Logistics processes of perishable food in the supply
chain include the distribution activities and the real time temperature
monitoring to fulfil the cold chain requirements. The paper presents
the use of RFID (Radio Frequency Identification) technology as an
identification tool of receiving and shipping activities in the cold
store. At the same time, the use of RFID data loggers with
temperature sensors is presented to observe and store the
temperatures for the purpose of analyzing the processes and having
the history data available for traceability purposes and efficient recall
management.
Abstract: A knowledge-based expert system with the acronym
RASPE is developed as an application tool to help decision makers in
construction companies make informed decisions about managing
risks in pipeline construction projects. Choosing to use expert
systems from all available artificial intelligence techniques is due to
the fact that an expert system is more suited to representing a
domain’s knowledge and the reasoning behind domain-specific
decisions. The knowledge-based expert system can capture the
knowledge in the form of conditional rules which represent various
project scenarios and potential risk mitigation/response actions. The
built knowledge in RASPE is utilized through the underlying
inference engine that allows the firing of rules relevant to a project
scenario into consideration. Paper provides an overview of the
knowledge acquisition process and goes about describing the
knowledge structure which is divided up into four major modules.
The paper shows one module in full detail for illustration purposes
and concludes with insightful remarks.
Abstract: Modelling of the earth's surface and evaluation of
urban environment, with 3D models, is an important research topic.
New stereo capabilities of high resolution optical satellites images,
such as the tri-stereo mode of Pleiades, combined with new image
matching algorithms, are now available and can be applied in urban
area analysis. In addition, photogrammetry software packages gained
new, more efficient matching algorithms, such as SGM, as well as
improved filters to deal with shadow areas, can achieve more dense
and more precise results.
This paper describes a comparison between 3D data extracted
from tri-stereo and dual stereo satellite images, combined with pixel
based matching and Wallis filter. The aim was to improve the
accuracy of 3D models especially in urban areas, in order to assess if
satellite images are appropriate for a rapid evaluation of urban
environments.
The results showed that 3D models achieved by Pleiades tri-stereo
outperformed, both in terms of accuracy and detail, the result
obtained from a Geo-eye pair. The assessment was made with
reference digital surface models derived from high resolution aerial
photography. This could mean that tri-stereo images can be
successfully used for the proposed urban change analyses.
Abstract: In this paper, the effect of grades 32.4 and 42.5
Portland-limestone cements generally used for concrete production in
Nigeria on concrete compressive strength is investigated.
Investigation revealed that the compressive strength of concrete
produced with Portland-limestone cement grade 42.5 is generally
higher than that produced with cement grade 32.5. The percentage
difference between the compressive strengths of the concrete cubes
produced with Portland-limestone cement grades 42.5 and 32.5 is
inversely proportional to the richness of the concrete with the highest
and the least percentage difference associated with the 1:2:4 and
1:1:2 mix ratios respectively. It is recommended that cement grade
42.5 be preferred for construction in Nigeria as this will lead to the
construction of stronger concrete structures, which will reduce the
incidence of failure of building and other concrete structures at no
additional cost since the cost of both cement grades are the same.
Abstract: Solar energy is a good option among renewable
energy resources due to its easy availability and abundance. The
simplest and most efficient way to utilize solar energy is to convert it
into thermal energy and this can be done with the help of solar
collectors. The thermal performance of such collectors is poor due to
less heat transfer from the collector surface to air. In this work,
experimental investigations of single pass solar air heater having
triangular duct and provided with roughness element on the underside
of the absorber plate. V-shaped ribs are used for investigation having
three different values of relative roughness pitch (p/e) ranges from 4-
16 for a fixed value of angle of attack (α), relative roughness height
(e/Dh) and a relative gap distance (d/x) values are 60°, 0.044 and 0.60
respectively. Result shows that considerable augmentation in heat
transfer has been obtained by providing roughness.
Abstract: This research focused on comparing the critical
thinking of the teacher students before and after using Miller’s Model
learning activities and investigating their opinions. The sampling
groups were (1) fourth year 33 student teachers majoring in Early
Childhood Education and enrolling in semester 1 of academic year
2013 (2) third year 28 student teachers majoring in English and
enrolling in semester 2 of academic year 2013 and (3) third year 22
student teachers majoring in Thai and enrolling in semester 2 of
academic year 2013. The research instruments were (1) lesson plans
where the learning activities were settled based on Miller’s Model (2)
critical thinking assessment criteria and (3) a questionnaire on
opinions towards Miller’s Model based learning activities. The
statistical treatment was mean, deviation, different scores and T-test.
The result unfolded that (1) the critical thinking of the students after
the assigned activities was better than before and (2) the students’
opinions towards the critical thinking improvement activities based
on Miller’s Model ranged from the level of high to highest.
Abstract: The use OF adhesive anchors for wooden constructions is an efficient technology to connect and design timber members in new timber structures and to rehabilitate the damaged structural members of historical buildings. Due to the lack of standard regulation in this specific area of structural design, designers’ choices are still supported by test analysis that enables knowledge, and the prediction, of the structural behaviour of glued in rod joints. The paper outlines an experimental research activity aimed at identifying the tensile resistance capacity of several new adhesive joint prototypes made of epoxy resin, steel bar and timber, Oak and Douglas Fir species. The development of new adhesive connectors has been carried out by using epoxy to glue stainless steel bars into pre-drilled holes, characterised by smooth and rough internal surfaces, in timber samples. The realization of a threaded contact surface using a specific drill bit has led to an improved bond between wood and epoxy. The applied changes have also reduced the cost of the joints’ production. The paper presents the results of this parametric analysis and a Finite Element analysis that enables identification and study of the internal stress distribution in the proposed adhesive anchors.
Abstract: The dielectric properties and ionic conductivity of
novel "ceramic state" polymer electrolytes for high capacity lithium
battery are characterized by Radio frequency and Microwave
methods in two broad frequency ranges from 50 Hz to 20 KHz and 4
GHz to 40 GHz. This innovative solid polymer electrolyte which is
highly ionic conductive (10-3 S/cm at room temperature) from -40oC
to +150oC can be used in any battery application. Such polymer
exhibits properties more like a ceramic rather than polymer. The
various applied measurement methods produced accurate dielectric
results for comprehensive analysis of electrochemical properties and
ion transportation mechanism of this newly invented polymer
electrolyte. Two techniques and instruments employing air gap
measurement by Capacitance Bridge and in-waveguide measurement
by vector network analyzer are applied to measure the complex
dielectric spectra. The complex dielectric spectra are used to
determine the complex alternating current electrical conductivity and
thus the ionic conductivity.
Abstract: The study of the electrical signals produced by neural
activities of human brain is called Electroencephalography. In this
paper, we propose an automatic and efficient EEG signal
classification approach. The proposed approach is used to classify the
EEG signal into two classes: epileptic seizure or not. In the proposed
approach, we start with extracting the features by applying Discrete
Wavelet Transform (DWT) in order to decompose the EEG signals
into sub-bands. These features, extracted from details and
approximation coefficients of DWT sub-bands, are used as input to
Principal Component Analysis (PCA). The classification is based on
reducing the feature dimension using PCA and deriving the supportvectors
using Support Vector Machine (SVM). The experimental are
performed on real and standard dataset. A very high level of
classification accuracy is obtained in the result of classification.
Abstract: The well been of human beings on construction site is
very important, many man power had been lost through accidents
which kills or make workers physically unfit to carry out construction
activities, these in turn have multiple effects on the whole economy.
Thus it is necessary to put all safety items and regulations in place
before construction activities can commence. This study was carried
out in Ondo state of Nigeria to known and analyse the state of health
and safety of construction workers in the state. The study was done
using first hand observation method, 50 construction project sites
were visited in 10 major towns of Ondo state, questionnaires were
distributed and the results were analysed. The result show that
construction workers are being exposed to a lot of construction site
hazards due to lack of inadequate safety programmes and nonprovision
of appropriate safety materials for workers on site. From the
data gotten for each site visited and the statistical analysis, it can be
concluded that occurrence of accident on construction sites depends
significantly on the available safety facilities on the sites. The result of
the regression statistics show that the level of significant of the
dependence of occurrence of accident on the availability of safety
items on site is 0.0362 which is less than 0.05 maximum significant
level required. Therefore a vital way of sustaining our building
strategy is by given a detail attention to provision of adequate health
and safety items on construction sites which will reduce the
occurrence of accident, loss of man power and death of skilled
workers among others.
Abstract: Background: The effectiveness of mirror therapy
(MT) has been investigated in acute hemiplegia. The present study
examines whether MT, given during chronic stroke, was more
effective in promoting motor recovery of the lower extremity and
walking speed than standard rehabilitation alone. Methods: The study
enrolled 30 patients with chronic stroke. Fifteen patients each were
assigned to the treatment group and the control group. All patients
received a conventional rehabilitation program for a 4-week period.
In addition to this rehabilitation program, patients in the treatment
group received mirror therapy for 4 weeks, 5 days a week. Main
measures: Passive ankle joint dorsiflexion range of motion, gait
speed, Brunnstrom stages of motor recovery, plantar flexor muscle
tone by Modified Ashworth Scale. Results: No significant difference
was found in the outcome measures among groups before treatment.
When compared with standard rehabilitation, mirror therapy
improved Ankle ROM, Brunnstrom stages and waking speed
(p < 0.05). However, there were no significant differences between
two groups on MAS (P > 0.05).Conclusion: Mirror therapy combined
with a conventional stroke rehabilitation program enhances lowerextremity
motor recovery and walking speed in chronic stroke
patients.
Abstract: Interaction between human, location and activity
defines space. In the framework of these relations, space is a
container for current specifications in relations of the 3 mentioned
elements. The change of land utility considered with average
performance range, urban regulations, society requirements etc. will
provide welfare and comfort for citizens. From an engineering view it
is fundamental that choosing a proper location for a specific civil
activity requires evaluation of locations from different perspectives.
The debate of desirable establishment of municipal service elements
in urban regions is one of the most important issues related to urban
planning. In this paper, the research type is applicable based on goal,
and is descriptive and analytical based on nature. Initially existing
terminals in Esfahan are surveyed and then new locations are
presented based on evaluated criteria. In order to evaluate terminals
based on the considered factors, an AHP model is used at first to
estimate weight of different factors and then existing and suggested
locations are evaluated using Arc GIS software and AHP model
results. The results show that existing bus terminals are located in
fairly proper locations. Further results of this study suggest new
locations to establish terminals based on urban criteria.
Abstract: Modern low earth orbit (LEO) satellites that require multi-mission flexibility are highly likely to be repositioned between different operational orbits. While executing this process the satellite may experience high levels of vibration and environmental hazards, exposing the deployed solar panel to dangerous stress levels, fatigue and space debris, hence it is desirable to retract the solar array before satellite repositioning to avoid damage or failure.
A novel concept of deployable/retractable hybrid solar array systemcomposed of both rigid and flexible solar panels arranged within a petal formation, aimed to provide a greater power to volume ratio while dramatically reducing mass and cost is proposed.
Abstract: The 6th version of Universal modeling method for
centrifugal compressor stage calculation is described. Identification
of the new mathematical model was made. As a result of
identification the uniform set of empirical coefficients is received.
The efficiency definition error is 0,86 % at a design point. The
efficiency definition error at five flow rate points (except a point of
the maximum flow rate) is 1,22 %. Several variants of the stage with
3D impellers designed by 6th version program and quasi threedimensional
calculation programs were compared by their gas
dynamic performances CFD (NUMECA FINE TURBO).
Performance comparison demonstrated general principles of design
validity and leads to some design recommendations.
Abstract: Fiber Bragg optic sensor is embedded in composite
material to detect and monitor the damage that occurs in composite
structures. In this paper, we deal with the mode-Ι delamination to
determine the material strength to crack propagation, using the
coupling mode theory and T-matrix method to simulate the FBGs
spectrum for both uniform and non-uniform strain distribution. The
double cantilever beam test is modeled in FEM to determine the
longitudinal strain. Two models are implemented, the first is the
global half model, and the second is the sub-model to represent the
FBGs with higher refined mesh. This method can simulate damage in
composite structures and converting strain to a wavelength shifting in
the FBG spectrum.