Abstract: The application of a Static Synchronous Series Compensator (SSSC) controller to improve the transient stability performance of a power system is thoroughly investigated in this paper. The design problem of SSSC controller is formulated as an optimization problem and Particle Swarm Optimization (PSO) Technique is employed to search for optimal controller parameters. By minimizing the time-domain based objective function, in which the deviation in the oscillatory rotor angle of the generator is involved; transient stability performance of the system is improved. The proposed controller is tested on a weakly connected power system subjected to different severe disturbances. The non-linear simulation results are presented to show the effectiveness of the proposed controller and its ability to provide efficient damping of low frequency oscillations. It is also observed that the proposed SSSC controller improves greatly the voltage profile of the system under severe disturbances.
Abstract: The objective of this paper is to study the analysis and testing for determining the torsional stiffness of the student formula-s space frame. From past study, the space frame for Chulalongkorn University Student Formula team used in 2011 TSAE Auto Challenge Student Formula in Thailand was designed by considering required mass and torsional stiffness based on the numerical method and experimental method. The numerical result was compared with the experimental results to verify the torsional stiffness of the space frame. It can be seen from the large error of torsional stiffness of 2011 frame that the experimental result can not verify by the numerical analysis due to the different between the numerical model and experimental setting. In this paper, the numerical analysis and experiment of the same 2011 frame model is performed by improving the model setting. The improvement of both numerical analysis and experiment are discussed to confirm that the models from both methods are same. After the frame was analyzed and tested, the results are compared to verify the torsional stiffness of the frame. It can be concluded that the improved analysis and experiments can used to verify the torsional stiffness of the space frame.
Abstract: Since the actuator capacity is limited, in the real
application of active control systems under sever earthquakes it is
conceivable that the actuators saturate, hence the actuator saturation
should be considered as a constraint in design of optimal controllers.
In this paper optimal design of active controllers for nonlinear
structures by considering actuator saturation, has been studied. The
proposed method for designing optimal controllers is based on
defining an optimization problem which the objective has been to
minimize the maximum displacement of structure when a limited
capacity for actuator has been used. To this end a single degree of
freedom (SDF) structure with a bilinear hysteretic behavior has been
simulated under a white noise ground acceleration of different
amplitudes. Active tendon control mechanism, comprised of prestressed
tendons and an actuator, and extended nonlinear Newmark
method based instantaneous optimal control algorithm have been
used. To achieve the best results, the weights corresponding to
displacement, velocity, acceleration and control force in the
performance index have been optimized by the Distributed Genetic
Algorithm (DGA). Results show the effectiveness of the proposed
method in considering actuator saturation. Also based on the
numerical simulations it can be concluded that the actuator capacity
and the average value of required control force are two important
factors in designing nonlinear controllers which consider the actuator
saturation.
Abstract: This paper presents a comparative study on two most
popular control strategies for Permanent Magnet Synchronous Motor
(PMSM) drives: field-oriented control (FOC) and direct torque
control (DTC). The comparison is based on various criteria including
basic control characteristics, dynamic performance, and
implementation complexity. The study is done by simulation using
the Simulink Power System Blockset that allows a complete
representation of the power section (inverter and PMSM) and the
control system. The simulation and evaluation of both control
strategies are performed using actual parameters of Permanent
Magnet Synchronous Motor fed by an IGBT PWM inverter.
Abstract: This paper describes various stages of design and prototyping of a modular robot for use in various industrial applications. The major goal of current research has been to design and make different robotic joints at low cost capable of being assembled together in any given order for achieving various robot configurations. Five different types of joins were designed and manufactured where extensive research has been carried out on the design of each joint in order to achieve optimal strength, size, modularity, and price. This paper presents various stages of research and development undertaken to engineer these joints that include material selection, manufacturing, and strength analysis. The outcome of this research addresses the birth of a new generation of modular industrial robots with a wider range of applications and greater efficiency.
Abstract: The present work is concerned with sulfidation of Cu,
Zn and Ni containing plating wastewater with CaS. The sulfidation
experiments were carried out at a room temperature by adding solid
CaS to simulated metal solution containing either single-metal of Ni,
Zn and Cu, or Ni-Zn-Cu mixture. At first, the experiments were
conducted without pH adjustment and it was found that the complete
sulfidation of Zn and Ni was achieved at an equimolar ratio of CaS to a
particular metal. However, in the case of Cu, a complete copper
sulfidation was achieved at CaS to Cu molar ratio of about 2. In the
case of the selective sulfidation, a simulated plating solution
containing Cu, Zn and Ni at the concentration of 100 mg/dm3 was
treated with CaS under various pH conditions. As a result, selective
precipitation of metal sulfides was achieved by a sulfidation treatment
at different pH values. Further, the precipitation agents of NaOH,
Na2S and CaS were compared in terms of the average specific
filtration resistance and compressibility coefficients of metal sulfide
slurry. Consequently, based on the lowest filtration parameters of the
produced metal sulfides, it was concluded that CaS was the most
effective precipitation agent for separation and recovery of Cu, Zn and
Ni.
Abstract: These This paper looks into frameworks which aim at
furthering the discussion of the role of regenerative design practices
in a city-s historic core and the tool of urban design to achieve urban
revitalization on the island of Cyprus. It also examines the region-s
demographic mix, the effectiveness of its governmental coordination
and the strategies of adaptive reuse and strategic investments in older
areas with existing infrastructure. The two main prongs of
investigation will consider the effect of the existing and proposed
changes in the physical infrastructure and fabric of the city, as well as
the catalytic effect of sustainable urban design practices. Through this
process, the work hopes to integrate the contained potential within
the existing historic core and the contributions and participation of
the migrant and immigrant populations to the local economy. It also
examines ways in which this coupling of factors can bring to the front
the positive effects of this combined effort on an otherwise sluggish
local redevelopment effort. The data for this study is being collected
and organized as part of ongoing urban design and development
student workshop efforts in urban planning and design education.
The work is presented in graphic form and includes data collected
from interviews with study area organizations and the community at
large. Planning work is also based on best practices initiated by the
staff of the Nicosia Master Plan task force, which coordinates holistic
planning efforts for the historic center of the city of Nicosia.
Abstract: In this paper, we have combined some spatial derivatives with the optimised time derivative proposed by Tam and Webb in order to approximate the linear advection equation which is given by = 0. Ôêé Ôêé + Ôêé Ôêé x f t u These spatial derivatives are as follows: a standard 7-point 6 th -order central difference scheme (ST7), a standard 9-point 8 th -order central difference scheme (ST9) and optimised schemes designed by Tam and Webb, Lockard et al., Zingg et al., Zhuang and Chen, Bogey and Bailly. Thus, these seven different spatial derivatives have been coupled with the optimised time derivative to obtain seven different finite-difference schemes to approximate the linear advection equation. We have analysed the variation of the modified wavenumber and group velocity, both with respect to the exact wavenumber for each spatial derivative. The problems considered are the 1-D propagation of a Boxcar function, propagation of an initial disturbance consisting of a sine and Gaussian function and the propagation of a Gaussian profile. It is known that the choice of the cfl number affects the quality of results in terms of dissipation and dispersion characteristics. Based on the numerical experiments solved and numerical methods used to approximate the linear advection equation, it is observed in this work, that the quality of results is dependent on the choice of the cfl number, even for optimised numerical methods. The errors from the numerical results have been quantified into dispersion and dissipation using a technique devised by Takacs. Also, the quantity, Exponential Error for Low Dispersion and Low Dissipation, eeldld has been computed from the numerical results. Moreover, based on this work, it has been found that when the quantity, eeldld can be used as a measure of the total error. In particular, the total error is a minimum when the eeldld is a minimum.
Abstract: The urbanization phenomenon in Yogyakarta Special
Province, Indonesia, encouraged people move to the city for getting
jobs in the informal sectors. They live in some temporary houses in
the three main riverbanks: Gadjahwong, Code, and Winongo.
Triggered by its independent status they use it as the space for
accommodating domestic, social and economy activities because of
the non standardized room size of their houses, where are recognized
as the environmental hazards. This recognition makes the ambivalent
perception when was related to the twelfth point of the philosophy of
community development concept: the empowering individuals and
communities. Its spatial implication have actually described the
territory and the place making phenomena. By analyzing some data
collected the author-s fundamental research funded by The General
Directorate of Higher Education of Indonesia, this paper will discuss
how do the spatial implications of the occupants- behavior and the
numerous perceptions of those phenomena.
Abstract: The purpose of this research is to determine the
knowledge and skills possessed by instructional design (ID)
practitioners in Malaysia. As ID is a relatively new field in the
country and there seems to be an absence of any studies on its
community of practice, the main objective of this research is to
discover the tasks and activities performed by ID practitioners in
educational and corporate organizations as suggested by the
International Board of Standards for Training, Performance and
Instruction. This includes finding out the ID models applied in the
course of their work. This research also attempts to identify the
barriers and issues as to why some ID tasks and activities are rarely
or never conducted. The methodology employed in this descriptive
study was a survey questionnaire sent to 30 instructional designers
nationwide. The results showed that majority of the tasks and
activities are carried out frequently enough but omissions do occur
due to reasons such as it being out of job scope, the decision was
already made at a higher level, and the lack of knowledge and skills.
Further investigations of a qualitative manner should be conducted
to achieve a more in-depth understanding of ID practices in
Malaysia
Abstract: This paper presents a low cost design of heart beat monitoring device using reflectance mode PhotoPlethysmography (PPG). PPG is known for its simple construction, ease of use and cost effectiveness and can provide information about the changes in cardiac activity as well as aid in earlier non-invasive diagnostics. The proposed device is divided into three phases. First is the detection of pulses through the fingertip. The signal is then passed to the signal processing unit for the purpose of amplification, filtering and digitizing. Finally the heart rate is calculated and displayed on the computer using parallel port interface. The paper is concluded with prototyping of the device followed by verification procedure of the heartbeat signal obtained in laboratory setting.
Abstract: D-erythro-cyclohexylserine (D
chiral unnatural β-hydroxy amino acid expected for the synthesis of drug for AIDS treatment. To develop a continuous bioconversion
system with whole cell biocatalyst of D-threonine aldolase (D genes for the D-erythro-CHS production, D-threonine aldolase gene
was amplified from Ensifer arboris 100383 by direct PCR amplication using two degenerated oligonucleotide primers designed based on
genomic sequence of Shinorhizobium meliloti
Sequence analysis of the cloned DNA fragment revealed one
open-reading frame of 1059 bp and 386 amino acids. This putative
D-TA gene was cloned into NdeI and EcoRI (pEnsi
His-tag sequence or BamHI (pEnsi-DTA[2])
sequence of the pET21(a) vector. The expression level of the cloned gene was extremely overexpressed by E. coli BL21(DE3) transformed with pEnsi-DTA[1] compared to E. coli BL21(DE3) transformed with
pEnsi-DTA[2]. When the cells expressing the wild
used for D-TA enzyme activity, 12 mM glycine was successfully
detected in HPLC analysis. Moreover, the whole cells harbouring the
recombinant D-TA was able to synthesize D-erythro
of 0.6 mg/ml in a batch reaction.
Abstract: European Union candidate status provides a
strong motivation for decision-making in the candidate
countries in shaping the regional development policy where
there is an envisioned transfer of power from center to the
periphery. The process of Europeanization anticipates the
candidate countries configure their regional institutional
templates in the context of the requirements of the European
Union policies and introduces new instruments of incentive
framework of enlargement to be employed in regional
development schemes. It is observed that the contribution of
the local actors to the decision making in the design of the
allocation architectures enhances the efficiency of the funds
and increases the positive effects of the projects funded under
the regional development objectives. This study aims at
exploring the performances of the three regional development
grant schemes in Turkey, established and allocated under the
pre-accession process with a special emphasis given to the
roles of the national and local actors in decision-making for
regional development. Efficiency analyses have been
conducted using the DEA methodology which has proved to
be a superior method in comparative efficiency and
benchmarking measurements. The findings of this study as
parallel to similar international studies, provides that the
participation of the local actors to the decision-making in
funding contributes both to the quality and the efficiency of
the projects funded under the EU schemes.
Abstract: To identify an endothelial cell-specific promoter suitable for vascular-specific targeting, we tested five promoters in vitro--Tie2SE, Tie2LE, ICAM2, Flt-1 and vWF--for promoter activity and specificity in endothelial cells, smooth muscle cells and non-vascular resident cells as well as tissues. These promoters, except for vWF, exhibited good endothelial activity and specificity in vitro. In a syngenic heart transplantation model, the ICAM2 promoter was variably functional in coronary endothelial cells of donor hearts. Thus, the ICAM2, Flt-1, Tie2SE and Tie2LE promoters hold promise for endothelial-specific targeting, but in vitro expression may not predict in vivo expression.
Abstract: Due to the recovering global economy, enterprises are
increasingly focusing on logistics. Investing in logistic measures for
a production generates a large potential for achieving a good starting
point within a competitive field. Unlike during the global economic
crisis, enterprises are now challenged with investing available capital
to maximize profits. In order to be able to create an informed and
quantifiably comprehensible basis for a decision, enterprises need an
adequate model for logistically and monetarily evaluating measures
in production. The Collaborate Research Centre 489 (SFB 489) at the
Institute for Production Systems (IFA) developed a Logistic
Information System which provides support in making decisions and
is designed specifically for the forging industry. The aim of a project
that has been applied for is to now transfer this process in order to
develop a universal approach to logistically and monetarily evaluate
measures in production.
Abstract: This paper describes a new supervised fusion (hybrid)
electrocardiogram (ECG) classification solution consisting of a new
QRS complex geometrical feature extraction as well as a new version
of the learning vector quantization (LVQ) classification algorithm
aimed for overcoming the stability-plasticity dilemma. Toward this
objective, after detection and delineation of the major events of ECG
signal via an appropriate algorithm, each QRS region and also its
corresponding discrete wavelet transform (DWT) are supposed as
virtual images and each of them is divided into eight polar sectors.
Then, the curve length of each excerpted segment is calculated
and is used as the element of the feature space. To increase the
robustness of the proposed classification algorithm versus noise,
artifacts and arrhythmic outliers, a fusion structure consisting of
five different classifiers namely as Support Vector Machine (SVM),
Modified Learning Vector Quantization (MLVQ) and three Multi
Layer Perceptron-Back Propagation (MLP–BP) neural networks with
different topologies were designed and implemented. The new proposed
algorithm was applied to all 48 MIT–BIH Arrhythmia Database
records (within–record analysis) and the discrimination power of the
classifier in isolation of different beat types of each record was
assessed and as the result, the average accuracy value Acc=98.51%
was obtained. Also, the proposed method was applied to 6 number
of arrhythmias (Normal, LBBB, RBBB, PVC, APB, PB) belonging
to 20 different records of the aforementioned database (between–
record analysis) and the average value of Acc=95.6% was achieved.
To evaluate performance quality of the new proposed hybrid learning
machine, the obtained results were compared with similar peer–
reviewed studies in this area.
Abstract: Information is power. Geographical information is an
emerging science that is advancing the development of knowledge to
further help in the understanding of the relationship of “place" with
other disciplines such as crime. The researchers used crime data for
the years 2004 to 2007 from the Baguio City Police Office to
determine the incidence and actual locations of crime hotspots.
Combined qualitative and quantitative research methodology was
employed through extensive fieldwork and observation, geographic
visualization with Geographic Information Systems (GIS) and Global
Positioning Systems (GPS), and data mining. The paper discusses
emerging geographic visualization and data mining tools and
methodologies that can be used to generate baseline data for
environmental initiatives such as urban renewal and rejuvenation.
The study was able to demonstrate that crime hotspots can be
computed and were seen to be occurring to some select places in the
Central Business District (CBD) of Baguio City. It was observed that
some characteristics of the hotspot places- physical design and milieu
may play an important role in creating opportunities for crime. A list
of these environmental attributes was generated. This derived
information may be used to guide the design or redesign of the urban
environment of the City to be able to reduce crime and at the same
time improve it physically.
Abstract: As networking has become popular, Web-learning
tends to be a trend while designing a tool. Moreover, five-axis
machining has been widely used in industry recently; however, it has
potential axial table colliding problems. Thus this paper aims at
proposing an efficient web-learning collision detection tool on
five-axis machining. However, collision detection consumes heavy
resource that few devices can support, thus this research uses a
systematic approach based on web knowledge to detect collision. The
methodologies include the kinematics analyses for five-axis motions,
separating axis method for collision detection, and computer
simulation for verification. The machine structure is modeled as STL
format in CAD software. The input to the detection system is the
g-code part program, which describes the tool motions to produce the
part surface. This research produced a simulation program with C
programming language and demonstrated a five-axis machining
example with collision detection on web site. The system simulates the
five-axis CNC motion for tool trajectory and detects for any collisions
according to the input g-codes and also supports high-performance
web service benefiting from C. The result shows that our method
improves 4.5 time of computational efficiency, comparing to the
conventional detection method.
Abstract: This research contribution is drafted to present the
orbit design, orbit propagator and geomagnetic field estimator for the
nanosatellites specifically for the upcoming CUBESAT, ICUBE-1 of
the Institute of Space Technology (IST), Islamabad, Pakistan. The
ICUBE mission is designed for the low earth orbit at the approximate
height of 700KM. The presented research endeavor designs the
Keplarian elements for ICUBE-1 orbit while incorporating the
mission requirements and propagates the orbit using J2 perturbations,
The attitude determination system of the ICUBE-1 consists of
attitude determination sensors like magnetometer and sun sensor. The
Geomagnetic field estimator is developed according to the model of
International Geomagnetic Reference Field (IGRF) for comparing the
magnetic field measurements by the magnetometer for attitude
determination. The output of the propagator namely the Keplarians
position and velocity vectors and the magnetic field vectors are
compared and verified with the same scenario generated in the
Satellite Tool Kit (STK).
Abstract: The paper presents an overview of environmental
issues that may be expected with nuclear desalination. The analysis
of coupling nuclear power with desalination plants indicates that
adverse marine impacts can be mitigated with alternative intake
designs or cooling systems. The atmospheric impact of desalination
may be greatly reduced through the coupling with nuclear power,
while maximizing the socio-economic benefit for both processes. The
potential for tritium contamination of the desalinated water was
reviewed. Experience with the systems and practices related to the
radiological quality of the product water, shows no examples of
cross-contamination. Furthermore, the indicators for the public
acceptance of nuclear desalination, as one of the most important
sustainability aspects of any such large project, show a positive trend.
From the data collected, a conclusion is made that nuclear
desalination should be supported by decision-makers.