Abstract: This study was conducted to determine sex
differentiation of laboratory reared Elm nymphalid (Nymphalis
polychloros Linnaeus, 1758) by examining the morphological
structure of pupal stage. Laboratory colony of elm nymphalid, reared
on pear leaves, was used to set up experiments. It was performed
with 5 replications having 8 pupae for each replication. Dorsal,
ventral and lateral parts of external morphological structures of pupae
were examined by Olympus SZX9 stereozoom microscope and
photographed. When fully grown, mature larvae wander the highest
part of the rearing cage and pupae were formed hanging by
cremaster. After completing prepupa stage about 1.5±0.3 days, they
all pupated. Pupal stage was completed at 24±1°C about 4.38±1.20
days. Pupal weights were 0.483±0.05 g in females and 0.392±0.08 g
(n=40) in males respectively. Pupal emergence rate was 95%, with
22 females and 16 males. Examinations of ventral parts of 8th, 9th,
and 10th abdominal segments revealed that anal opening were found
at 10th abdominal segment in both sexes, 3 lumps were determined at
9th abdominal segments then the specific opening structure at 8th
segment was only found on female pupae.
Abstract: In this paper, we present a new segmentation approach
for liver lesions in regions of interest within MRI (Magnetic
Resonance Imaging). This approach, based on a two-cluster Fuzzy CMeans
methodology, considers the parameter variable compactness
to handle uncertainty. Fine boundaries are detected by a local
recursive merging of ambiguous pixels with a sequential forward
floating selection with Zernike moments. The method has been tested
on both synthetic and real images. When applied on synthetic images,
the proposed approach provides good performance, segmentations
obtained are accurate, their shape is consistent with the ground truth,
and the extracted information is reliable. The results obtained on MR
images confirm such observations. Our approach allows, even for
difficult cases of MR images, to extract a segmentation with good
performance in terms of accuracy and shape, which implies that the
geometry of the tumor is preserved for further clinical activities (such
as automatic extraction of pharmaco-kinetics properties, lesion
characterization, etc.).
Abstract: In this paper, the specific sound Transmission Loss
(TL) of the Laminated Composite Plate (LCP) with different material
properties in each layer is investigated. The numerical method to
obtain the TL of the LCP is proposed by using elastic plate theory. The
transfer matrix approach is novelty presented for computational
efficiency in solving the numerous layers of dynamic stiffness matrix
(D-matrix) of the LCP. Besides the numerical simulations for
calculating the TL of the LCP, the material properties inverse method
is presented for the design of a laminated composite plate analogous to
a metallic plate with a specified TL. As a result, it demonstrates that
the proposed computational algorithm exhibits high efficiency with a
small number of iterations for achieving the goal. This method can be
effectively employed to design and develop tailor-made materials for
various applications.
Abstract: RF magnetron sputtering is used on the ceramic targets,
each of which contains zinc oxide (ZnO), zinc oxide doped with
aluminum (AZO) and zinc oxide doped with gallium (GZO). The XRD
analysis showed a preferred orientation along the (002) plane for ZnO,
AZO, and GZO films. The AZO film had the best electrical properties;
it had the lowest resistivity of 6.6 × 10-4 cm, the best sheet resistance of
2.2 × 10-1 Ω/square, and the highest carrier concentration of 4.3 × 1020
cm-3, as compared to the ZnO and GZO films.
Abstract: These Monolayer and multilayer coatings of CrN and
AlCrN deposited on 100Cr6 (AISI 52100) substrate by PVD
magnetron sputtering system. The microstructures of the coatings
were characterized using atomic force microscopy (AFM). The AFM
analysis revealed the presence of domes and craters that are
uniformly distributed over all surfaces of the various layers.
Nanoindentation measurement of CrN coating showed maximum
hardness (H) and modulus (E) of 14 GPa and 190 GPa, respectively.
The measured H and E values of AlCrN coatings were found to be 30
GPa and 382 GPa, respectively. The improved hardness in both the
coatings was attributed mainly to a reduction in crystallite size and
decrease in surface roughness. The incorporation of Al into the CrN
coatings has improved both hardness and Young’s modulus.
Abstract: The effects of flame-holder position, the ratio of flame
holder diameter to combustion chamber diameter and injection angle
on fuel propulsive droplets sizing and effective mass fraction have
been studied by a cold flow. We named the mass of fuel vapor inside
the flammability limit as the effective mass fraction. An empty
cylinder as well as a flame-holder which are a simulator for duct
combustion has been considered. The airflow comes into the cylinder
from one side and injection operation will be done by four nozzles
which are located on the entrance of cylinder. To fulfill the
calculations a modified version of KIVA-3V code which is a
transient, three-dimensional, multiphase, multi component code for
the analysis of chemically reacting flows with sprays, is used.
Abstract: This paper is based on a large questionnaire study. The
paper presents how all participants and subgroups (upper- and
lower-level white-collar workers) answered the question, “Have you
had an ache, pain, or numbness, which you associate with desktop
computer use, in the different body parts during the last 12 months?’
14.6% of participants (19.4% of women and 8.2% of men) reported
that they had often or very often physical symptoms in the neck. Even
if our results cannot prove a causal relation of symptoms with
computer use, show that workers believe that computer use can
influence their wellbeing: this is important when devising treatment
modalities to decrease these physical symptoms.
Abstract: New design of three dimensional (3D) flywheel system
based on gimbal and gyro mechanics is proposed. The 3D flywheel
device utilizes the rotational motion of three spherical shells and the
conservation of angular momentum to achieve planar locomotion.
Actuators mounted to the ring-shape frames are installed within the
system to drive the spherical shells to rotate, for the purpose of steering
and stabilization. Similar to the design of 2D flywheel system, it is
expected that the spherical shells may function like a “flyball” to store
and supply mechanical energy; additionally, in comparison with
typical single-wheel and spherical robots, the 3D flywheel can be used
for developing omnidirectional robotic systems with better mobility.
The Lagrangian method is applied to derive the equation of motion of
the 3D flywheel system, and simulation studies are presented to verify
the proposed design.
Abstract: The purpose of the paper is to address the strategic
risk issues surrounding Hindi film distribution in Mumbai for a film
distributor, who acts as an entrepreneur when launching a product
(movie) in the market (film territory).The paper undertakes a
fundamental review of films and risk in the Hindi film industry and
applies Grounded Theory technique to understand the complex
phenomena of risk taking behavior of the film distributors (both
independent and studios) in Mumbai. Rich in-depth interviews with
distributors are coded to develop core categories through constant
comparison leading to conceptualization of the phenomena of
interest. This paper is a first-of-its-kind-attempt to understand risk
behavior of a distributor, which is akin to entrepreneurial risk
behavior under conditions of uncertainty.
Abstract: This study utilizes a frequency domain approach over
the period of 1996 to 2013 to examine the causal relationship between
governance and economic growth in ten Asian countries, which have
different levels of democracy; classified as “Free”, “Partly Free”, and
“Not Free” countries. The empirical results show that there is no
Granger causality running from governance to economic growth in
“Not Free” countries and “Partly Free” countries with the exception of
Singapore. As for “Free” countries such as South Korea and Taiwan,
there is a one-way causality running from governance to economic
growth. The findings of this study indicate that policy makers in South
Korea, Taiwan, and Singapore could use governance index to improve
their predictions of the future economic growth.
Abstract: This work presents an improved single fiber pull-out
test for fiber/matrix interface characterization. This test has been
used to study the Inter-Facial Shear Strength ‘IFSS’ of hemp fibers
reinforced polypropylene (PP). For this aim, the fiber diameter
has been carefully measured using a tomography inspired method.
The fiber section contour can then be approximated by a circle
or a polygon. The results show that the IFSS is overestimated if
the circular approximation is used. The Influence of the molding
temperature on the IFSS has also been studied. We find that a molding
temperature of 183◦C leads to better interfacial properties. Above or
below this temperature the interface strength is reduced.
Abstract: Distillery spentwash contains high chemical oxygen
demand (COD), biological oxygen demand (BOD), color, total
dissolved solids (TDS) and other contaminants even after biological
treatment. The effluent can’t be discharged as such in the surface
water bodies or land without further treatment. Reverse osmosis (RO)
treatment plants have been installed in many of the distilleries at
tertiary level in many of the distilleries in India, but are not properly
working due to fouling problem which is caused by the presence of
high concentration of organic matter and other contaminants in
biologically treated spentwash. In order to make the membrane
treatment a proven and reliable technology, proper pre-treatment is
mandatory. In the present study, ultra-filtration (UF) for pretreatment
of RO at tertiary stage has been performed. Operating
parameters namely initial pH (pHo: 2–10), trans-membrane pressure
(TMP: 4-20 bars) and temperature (T: 15-43°C) were used for
conducting experiments with UF system. Experiments were
optimized at different operating parameters in terms of COD, color,
TDS and TOC removal by using response surface methodology
(RSM) with central composite design. The results showed that
removal of COD, color and TDS was 62%, 93.5% and 75.5%
respectively, with UF, at optimized conditions with increased
permeate flux from 17.5 l/m2/h (RO) to 38 l/m2/h (UF-RO). The
performance of the RO system was greatly improved both in term of
pollutant removal as well as water recovery.
Abstract: Biodiesel production from vegetable oil will produce
glycerol as by-product about 10% of the biodiesel production. The
amount of glycerol that was produced needed alternative way to
handling immediately so as to not become the waste that polluted
environment. One of the solutions was to process glycerol to
polyglycidyl nitrate (PGN). PGN is synthesized from glycerol by
three-step reactions i.e. nitration of glycerol, cyclization of 13-
dinitroglycerine and polymerization of glycosyl nitrate. Optimum
condition of nitration of glycerol with nitric acid has not been known.
Thermodynamic feasibility should be done before run experiments in
the laboratory. The aim of this study was to determine the parameters
those affect nitration of glycerol and nitric acid and chose the
operation condition. Many parameters were simulated to verify its
possibility to experiment under conditions which would get the
highest conversion of 1, 3-dinitroglycerine and which was the ideal
condition to get it. The parameters that need to be studied to obtain
the highest conversion of 1, 3-dinitroglycerine were mol ratio of
nitric acid/glycerol, reaction temperature, mol ratio of
glycerol/dichloromethane and pressure. The highest conversion was
obtained in the range of mol ratio of nitric acid /glycerol between 2/1
– 5/1, reaction temperature of 5-25oC and pressure of 1 atm. The
parameters that need to be studied further to obtain the highest
conversion of 1.3 DNG are mol ratio of nitric acid/glycerol and
reaction temperature.
Abstract: In this study, to clarify the effectiveness of an
aluminum/chromium/tungsten-based-coated tool for cutting sintered
steel, tool wear was experimentally investigated. The sintered steel
was turned with the (Al60,Cr25,W15)N-, (Al60,Cr25,W15)(C,N)- and
(Al64,Cr28,W8)(C,N)-coated cemented carbide tools according to the
physical vapor deposition (PVD) method. Moreover, the tool wear of
the aluminum/chromium/tungsten-based-coated item was compared
with that of the (Al,Cr)N coated tool. Furthermore, to clarify the tool
wear mechanism of the aluminum/chromium/tungsten-coating film for
cutting sintered steel, Scanning Electron Microscope observation and
Energy Dispersive x-ray Spectroscopy mapping analysis were
conducted on the abraded surface. The following results were
obtained: (1) The wear progress of the (Al64,Cr28,W8)(C,N)-coated
tool was the slowest among that of the five coated tools. (2) Adding
carbon (C) to the aluminum/chromium/tungsten-based-coating film
was effective for improving the wear-resistance. (3) The main wear
mechanism of the (Al60,Cr25,W15)N-, the (Al60,Cr25,W15)(C,N)-
and the (Al64,Cr28,W8)(C,N)-coating films was abrasive wear.
Abstract: The economic use and ease of construction of profiled
deck composite slab is marred with the complex and un-economic
strength verification required for the serviceability and general safety
considerations. Beside these, albeit factors such as shear span length,
deck geometries and mechanical frictions greatly influence the
longitudinal shear strength, that determines the ultimate strength of
profiled deck composite slab, and number of methods available for its
determination; partial shear and slope-intercept are the two methods
according to Euro-code 4 provision. However, the complexity
associated with shear behavior of profiled deck composite slab, the
use of these methods in determining the load carrying capacities of
such slab yields different and conflicting values. This couple with the
time and cost constraint associated with the strength verification is a
source of concern that draws more attentions nowadays, the issue is
critical. Treating some of these known shear strength influencing
factors as random variables, the load carrying capacity violation of
profiled deck composite slab from the use of the two-methods
defined according to Euro-code 4 are determined using reliability
approach, and comparatively studied. The study reveals safety values
from the use of m-k method shows good standing compared with that
from the partial shear method.
Abstract: The aim of the present study is to detect the chaotic
behavior in monetary economic relevant dynamical system. The
study employs three different forms of Taylor rules: current, forward,
and backward looking. The result suggests the existence of the
chaotic behavior in all three systems. In addition, the results strongly
represent that using expectations in policy rule especially rational
expectation hypothesis can increase complexity of the system and
leads to more chaotic behavior.
Abstract: Bicycle Level of Service (BLOS) is a measure for
evaluating street conditions for cyclists. Currently, various methods
are proposed for BLOS. These analytical methods however have
some drawbacks: they usually assume cyclists as users that can share
street facilities with motorized vehicles, it is not easy to link them to
design process and they are not easy to follow. In addition, they only
support a narrow range of cycling facilities and may not be applicable
for all situations. Along this, the current paper introduces various
effective design factors for bicycle-friendly streets. This study
considers cyclists as users of streets who have special needs and
facilities. Therefore, the key factors that influence BLOS based on
different cycling facilities that are proposed by developed guidelines
and literature are identified. The combination of these factors
presents a complete set of effective design factors for bicycle-friendly
streets. In addition, the weight of each factor in existing BLOS
models is estimated and these effective factors are ranked based on
these weights. These factors and their weights can be used in further
studies to propose special bicycle-friendly street design model.
Abstract: The main parameters affecting the workability are the
water content, particle size, and the total surface of the grains, as long
as the mixing water begins by wetting the surface of the grains and
then fills the voids between the grains to form entrapped water, the
quantity of water remaining is called free water. The aim of this study is to undertake a fractal approach through
the relationship between the concrete formulation parameters and
workability. To develop this approach a series of concrete taken from
the literature was investigated by varying formulation parameters
such as G/S, the quantity of cement C and the quantity of water W. We also call another model as the model of water layer thickness
and model of paste layer thickness to judge their relevance, hence the
following results: the relevance of the water layer thickness model is
considered as a relevant when there is a variation in the water
quantity. The model of the paste layer thickness is only applicable if
we considered that the paste is made with the grain value Dmax =
2.85: value from which we see a stability of the model.
Abstract: We apply the non-parametric, unconditional,
hyperbolic order-α quantile estimator to appraise the relative
efficiency of Microfinance Institutions in Africa in terms of outreach.
Our purpose is to verify if these institutions, which must constantly
try to strike a compromise between their social role and financial
sustainability are operationally efficient.
Using data on African MFIs extracted from the Microfinance
Information eXchange (MIX) database and covering the 2004 to
2006 periods, we find that more efficient MFIs are also the most
profitable. This result is in line with the view that social performance
is not in contradiction with the pursuit of excellent financial
performance. Our results also show that large MFIs in terms of asset
and those charging the highest fees are not necessarily the most
efficient.
Abstract: The efficient and economic allocation of resources is
one main goal in the field of production planning and control.
Nowadays, a new variable gains in importance throughout the
planning process: Energy. Energy-efficiency has already been widely
discussed in literature, but with a strong focus on reducing the overall
amount of energy used in production. This paper provides a brief
systematic approach, how energy-supply-orientation can be used for
an energy-cost-efficient production planning and thus combining the
idea of energy-efficiency and energy-flexibility.