Abstract: This paper presents the 20-GHz fractional PLL (Phase
Locked Loop) circuit for the next generation Wi-Fi by using 90 nm
TSMC process. The newly suggested millimeter wave 16/17
pre-scalar is designed and verified by measurement to make the
fractional PLL having a low quantization noise. The operational
bandwidth of the 60 GHz system is 15 % of the carrier frequency
which requires large value of Kv (VCO control gain) resulting in
degradation of phase noise. To solve this problem, this paper adopts
AFC (Automatic Frequency Controller) controlled 4-bit millimeter
wave VCO with small value of Kv. Also constant Kv is implemented
using 4-bit varactor bank. The measured operational bandwidth is 18.2
~ 23.2 GHz which is 25 % of the carrier frequency. The phase noise of
-58 and -96.2 dBc/Hz at 100 KHz and 1 MHz offset is measured
respectively. The total power consumption of the PLL is only 30 mW.
Abstract: This paper reported an experimental research of
steady-state heat transfer behaviour of a gas flowing through a fixed
bed under the different operating conditions. Studies had been carried
out in a fixed-bed packed methanol synthesis catalyst percolated by air
at appropriate flow rate. Both radial and axial direction temperature
distribution had been investigated under the different operating
conditions. The effects of operating conditions including the reactor
inlet air temperature, the heating pipe temperature and the air flow rate
on temperature distribution was investigated and the experimental
results showed that a higher inlet air temperature was conducive to
uniform temperature distribution in the fixed bed. A large temperature
drop existed at the radial direction, and the temperature drop increased
with the heating pipe temperature increasing under the experimental
conditions; the temperature profile of the vicinity of the heating pipe
was strongly affected by the heating pipe temperature. A higher air
flow rate can improve the heat transfer in the fixed bed. Based on the
thermal distribution, heat transfer models of the fixed bed could be
established, and the characteristics of the temperature distribution in
the fixed bed could be finely described, that had an important practical
significance.
Abstract: Wireless mesh networks based on IEEE 802.11
technology are a scalable and efficient solution for next generation
wireless networking to provide wide-area wideband internet access to
a significant number of users. The deployment of these wireless mesh
networks may be within different authorities and without any
planning, they are potentially overlapped partially or completely in
the same service area. The aim of the proposed model is design a new
model to Enhancement Throughput of Unplanned Wireless Mesh
Networks Deployment Using Partitioning Hierarchical Cluster
(PHC), the unplanned deployment of WMNs are determinates there
performance. We use throughput optimization approach to model the
unplanned WMNs deployment problem based on partitioning
hierarchical cluster (PHC) based architecture, in this paper the
researcher used bridge node by allowing interworking traffic between
these WMNs as solution for performance degradation.
Abstract: Some Chromium (III) complexes were synthesized
with three amino acids: L Glutamic Acid, Glycine, and L-cysteine as
the ligands, in order to provide a new supplement containing Cr(III)
for patients with type 2 diabetes mellitus. The complexes have been
prepared by refluxing a mixture of Chromium(III) chloride in
aqueous solution with L-glutamic acid, Glycine, and L-cysteine after
pH adjustment by sodium hydroxide. These complexes were
characterized by Infrared and Uv-Vis spectrophotometer and
Elemental analyzer. The product yields of four products were 87.50
and 56.76% for Cr-Glu complexes, 46.70% for Cr-Gly complex and
40.08% for Cr-Cys complex respectively. The predicted structure of
the complexes are [Cr(glu)2(H2O)2].xH2O, Cr(gly)3..xH2O and
Cr(cys)3.xH2O., respectively.
Abstract: With the exponential rise in the number of multimedia
applications available, the best-effort service provided by the Internet
today is insufficient. Researchers have been working on new
architectures like the Next Generation Network (NGN) which, by
definition, will ensure Quality of Service (QoS) in an all-IP based
network [1]. For this approach to become a reality, reservation of
bandwidth is required per application per user. WiMAX (Worldwide
Interoperability for Microwave Access) is a wireless communication
technology which has predefined levels of QoS which can be
provided to the user [4]. IPv6 has been created as the successor for
IPv4 and resolves issues like the availability of IP addresses and
QoS. This paper provides a design to use the power of WiMAX as an
NSP (Network Service Provider) for NGN using IPv6. The use of the
Traffic Class (TC) field and the Flow Label (FL) field of IPv6 has
been explained for making QoS requests and grants [6], [7]. Using
these fields, the processing time is reduced and routing is simplified.
Also, we define the functioning of the ASN gateway and the NGN
gateway (NGNG) which are edge node interfaces in the NGNWiMAX
design. These gateways ensure QoS management through
built in functions and by certain physical resources and networking
capabilities.
Abstract: Image compression can improve the performance of
the digital systems by reducing time and cost in image storage
and transmission without significant reduction of the image quality.
Furthermore, the discrete cosine transform has emerged as the new
state-of-the art standard for image compression. In this paper, a
hybrid image compression technique based on reversible blockade
transform coding is proposed. The technique, implemented over
regions of interest (ROIs), is based on selection of the coefficients
that belong to different transforms, depending on the coefficients is
proposed. This method allows: (1) codification of multiple kernals
at various degrees of interest, (2) arbitrary shaped spectrum,and (3)
flexible adjustment of the compression quality of the image and the
background. No standard modification for JPEG2000 decoder was
required. The method was applied over different types of images.
Results show a better performance for the selected regions, when
image coding methods were employed for the whole set of images.
We believe that this method is an excellent tool for future image
compression research, mainly on images where image coding can
be of interest, such as the medical imaging modalities and several
multimedia applications. Finally VLSI implementation of proposed
method is shown. It is also shown that the kernal of Hartley and
Cosine transform gives the better performance than any other model.
Abstract: Iron in groundwater is one of the problems that render the water unsuitable for drinking. The concentration above 0.3 mg/L is common in groundwater. The conventional method of removal is by precipitation under oxic condition. In this study, iron removal under anaerobic conditions was examined by batch experiment as a main purpose. The process involved by purging of groundwater samples with H2S to form iron sulfide. Removal up to 83% for 1 mg/L iron solution was achieved. The removal efficiency dropped to 82% and 75% for the higher initial iron concentrations 3.55 and 5.01 mg/L, respectively. The average residual sulfide concentration in water after the process was 25*g/L. The Eh level during the process was -272 mV. The removal process was found to follow the first order reaction with average rate constant of 4.52 x 10-3. The half-life for the concentrations to reduce from initial values was 157 minutes.
Abstract: This paper features the modeling and design of a
Robust Decentralized Fast Output Sampling (RDFOS) Feedback
control technique for the active vibration control of a smart flexible
multimodel Euler-Bernoulli cantilever beams for a multivariable
(MIMO) case by retaining the first 6 vibratory modes. The beam
structure is modeled in state space form using the concept of
piezoelectric theory, the Euler-Bernoulli beam theory and the Finite
Element Method (FEM) technique by dividing the beam into 4 finite
elements and placing the piezoelectric sensor / actuator at two finite
element locations (positions 2 and 4) as collocated pairs, i.e., as
surface mounted sensor / actuator, thus giving rise to a multivariable
model of the smart structure plant with two inputs and two outputs.
Five such multivariable models are obtained by varying the
dimensions (aspect ratios) of the aluminium beam. Using model
order reduction technique, the reduced order model of the higher
order system is obtained based on dominant Eigen value retention
and the Davison technique. RDFOS feedback controllers are
designed for the above 5 multivariable-multimodel plant. The closed
loop responses with the RDFOS feedback gain and the magnitudes of
the control input are obtained and the performance of the proposed
multimodel smart structure system is evaluated for vibration control.
Abstract: Patients with diabetes are susceptible to chronic foot
wounds which may be difficult to manage and slow to heal.
Diagnosis and treatment currently rely on the subjective judgement of
experienced professionals. An objective method of tissue assessment
is required. In this paper, a data fusion approach was taken to wound
tissue classification. The supervised Maximum Likelihood and
unsupervised Multi-Modal Expectation Maximisation algorithms
were used to classify tissues within simulated wound models by
weighting the contributions of both colour and 3D depth information.
It was found that, at low weightings, depth information could show
significant improvements in classification accuracy when compared
to classification by colour alone, particularly when using the
maximum likelihood method. However, larger weightings were
found to have an entirely negative effect on accuracy.
Abstract: Worm propagation profiles have significantly changed
since 2003-2004: sudden world outbreaks like Blaster or Slammer
have progressively disappeared and slower but stealthier worms
appeared since, most of them for botnets dissemination. Decreased
worm virulence results in more difficult detection.
In this paper, we describe a stealth worm propagation model
which has been extensively simulated and analysed on a huge virtual
network. The main features of this model is its ability to infect any
Internet-like network in a few seconds, whatever may be its size while
greatly limiting the reinfection attempt overhead of already infected
hosts. The main simulation results shows that the combinatorial
topology of routing may have a huge impact on the worm propagation
and thus some servers play a more essential and significant role than
others. The real-time capability to identify them may be essential to
greatly hinder worm propagation.
Abstract: Because of the great advance in multimedia
technology, digital multimedia is vulnerable to malicious
manipulations. In this paper, a public key self-recovery block-based
video authentication technique is proposed which can not only
precisely localize the alteration detection but also recover the missing
data with high reliability. In the proposed block-based technique,
multiple description coding MDC is used to generate two codes (two
descriptions) for each block. Although one block code (one
description) is enough to rebuild the altered block, the altered block
is rebuilt with better quality by the two block descriptions. So using
MDC increases the ratability of recovering data. A block signature is
computed using a cryptographic hash function and a doubly linked
chain is utilized to embed the block signature copies and the block
descriptions into the LSBs of distant blocks and the block itself. The
doubly linked chain scheme gives the proposed technique the
capability to thwart vector quantization attacks. In our proposed
technique , anyone can check the authenticity of a given video using
the public key. The experimental results show that the proposed
technique is reliable for detecting, localizing and recovering the
alterations.
Abstract: The Taiwan government has started to promote the “Plain Landscape Afforestation and Greening Program" since 2002. A key task of the program was the payment for environmental services (PES), entitled the “Plain Landscape Afforestation Policy" (PLAP), which was certificated by the Executive Yuan on August 31, 2001 and enacted on January 1, 2002. According to the policy, it is estimated that the total area of afforestation will be 25,100 hectares by December 31, 2007. Until the end of 2007, the policy had been enacted for six years in total and the actual area of afforestation was 8,919.18 hectares. Among them, Taiwan Sugar Corporation (TSC) was accounted for 7,960 hectares (with 2,450.83 hectares as public service area) which occupied 86.22% of the total afforestation area; the private farmland promoted by local governments was accounted for 869.18 hectares which occupied 9.75% of the total afforestation area. Based on the above, we observe that most of the afforestation area in this policy is executed by TSC, and the achievement ratio by TSC is better than by others. It implies that the success of the PLAP is seriously related to the execution of TSC. The objective of this study is to analyze the relevant policy planning of TSC's participation in the PLAP, suggest complementary measures, and draw up effective adjustment mechanisms, so as to improve the effectiveness of executing the policy. Our main conclusions and suggestions are summarized as follows: 1. The main reason for TSC’s participation in the PLAP is based on their passive cooperation with the central government or company policy. Prior to TSC’s participation in the PLAP, their lands were mainly used for growing sugarcane. 2. The main factors of TSC's consideration on the selection of tree species are based on the suitability of land and species. The largest proportion of tree species is allocated to economic forests, and the lack of technical instruction was the main problem during afforestation. Moreover, the method of improving TSC’s future development in leisure agriculture and landscape business becomes a key topic. 3. TSC has developed short and long-term plans on participating in the PLAP for the future. However, there is no great willingness or incentive on budgeting for such detailed planning. 4. Most people from TSC interviewed consider the requirements on PLAP unreasonable. Among them, an unreasonable requirement on the number of trees accounted for the greatest proportion; furthermore, most interviewees suggested that the government should continue to provide incentives even after 20 years. 5. Since the government shares the same goals as TSC, there should be sufficient cooperation and communication that support the technical instruction and reduction of afforestation cost, which will also help to improve effectiveness of the policy.
Abstract: In the paper, a fast high-resolution range profile synthetic algorithm called orthogonal matching pursuit with sensing dictionary (OMP-SD) is proposed. It formulates the traditional HRRP synthetic to be a sparse approximation problem over redundant dictionary. As it employs a priori that the synthetic range profile (SRP) of targets are sparse, SRP can be accomplished even in presence of data lost. Besides, the computation complexity decreases from O(MNDK) flops for OMP to O(M(N + D)K) flops for OMP-SD by introducing sensing dictionary (SD). Simulation experiments illustrate its advantages both in additive white Gaussian noise (AWGN) and noiseless situation, respectively.
Abstract: Flash floods are considered natural disasters that can
cause casualties and demolishing of infra structures. The problem is
that flash floods, particularly in arid and semi arid zones, take place
in very short time. So, it is important to forecast flash floods earlier to
its events with a lead time up to 48 hours to give early warning alert
to avoid or minimize disasters. The flash flood took place over Wadi
Watier - Sinai Peninsula, in October 24th, 2008, has been simulated,
investigated and analyzed using the state of the art regional weather
model. The Weather Research and Forecast (WRF) model, which is a
reliable short term forecasting tool for precipitation events, has been
utilized over the study area. The model results have been calibrated
with the real data, for the same date and time, of the rainfall
measurements recorded at Sorah gauging station. The WRF model
forecasted total rainfall of 11.6 mm while the real measured one was
10.8 mm. The calibration shows significant consistency between
WRF model and real measurements results.
Abstract: A procedure commonly used in Job Shop Scheduling Problem (JSSP) to evaluate the neighborhoods functions that use the non-deterministic algorithms is the calculation of the critical path in a digraph. This paper presents an experimental study of the cost of computation that exists when the calculation of the critical path in the solution for instances in which a JSSP of large size is involved. The results indicate that if the critical path is use in order to generate neighborhoods in the meta-heuristics that are used in JSSP, an elevated cost of computation exists in spite of the fact that the calculation of the critical path in any digraph is of polynomial complexity.
Abstract: Business process automation is an important task in an
enterprise business environment software development. The
requirements of processing acceleration and automation level of
enterprises are inherently different from one organization to another.
We present a methodology and system for automation of business
process management system architecture by multi-agent collaboration
based on SOA. Design layer processes are modeled in semantic
markup language for web services application. At the core of our
system is considering certain types of human tasks to their further
automation across over multiple platform environments. An
improved abnormality processing with model for automation of
BPMS architecture by multi-agent collaboration based on SOA is
introduced. Validating system for efficiency of process automation,
an application for educational knowledge base instance would also be
described.
Abstract: This research is aimed to describe the application of robust regression and its advantages over the least square regression method in analyzing financial data. To do this, relationship between earning per share, book value of equity per share and share price as price model and earning per share, annual change of earning per share and return of stock as return model is discussed using both robust and least square regressions, and finally the outcomes are compared. Comparing the results from the robust regression and the least square regression shows that the former can provide the possibility of a better and more realistic analysis owing to eliminating or reducing the contribution of outliers and influential data. Therefore, robust regression is recommended for getting more precise results in financial data analysis.
Abstract: InGaAsN and GaAsN epitaxial layers with similar
nitrogen compositions in a sample were successfully grown on a
GaAs (001) substrate by solid source molecular beam epitaxy. An
electron cyclotron resonance nitrogen plasma source has been used to
generate atomic nitrogen during the growth of the nitride layers. The
indium composition changed from sample to sample to give
compressive and tensile strained InGaAsN layers. Layer
characteristics have been assessed by high-resolution x-ray
diffraction to determine the relationship between the lattice constant
of the GaAs1-yNy layer and the fraction x of In. The objective was to
determine the In fraction x in an InxGa1-xAs1-yNy epitaxial layer which
exactly cancels the strain present in a GaAs1-yNy epitaxial layer with
the same nitrogen content when grown on a GaAs substrate.
Abstract: Workflow Management Systems (WfMS) alloworganizations to streamline and automate business processes and reengineer their structure. One important requirement for this type of system is the management and computation of the Quality of Service(QoS) of processes and workflows. Currently, a range of Web processes and workflow languages exist. Each language can be characterized by the set of patterns they support. Developing andimplementing a suitable and generic algorithm to compute the QoSof processes that have been designed using different languages is a difficult task. This is because some patterns are specific to particular process languages and new patterns may be introduced in future versions of a language. In this paper, we describe an adaptive algorithm implemented to cope with these two problems. The algorithm is called adaptive since it can be dynamically changed as the patterns of a process language also change.
Abstract: Classification is an important topic in machine learning
and bioinformatics. Many datasets have been introduced for
classification tasks. A dataset contains multiple features, and the quality of features influences the classification accuracy of the dataset.
The power of classification for each feature differs. In this study, we
suggest the Classification Influence Index (CII) as an indicator of classification power for each feature. CII enables evaluation of the
features in a dataset and improved classification accuracy by transformation of the dataset. By conducting experiments using CII
and the k-nearest neighbor classifier to analyze real datasets, we confirmed that the proposed index provided meaningful improvement
of the classification accuracy.