Abstract: This paper deals with nonlinear vibration analysis
using finite element method for frame structures consisting of elastic
and viscoelastic damping layers supported by multiple nonlinear
concentrated springs with hysteresis damping. The frame is supported
by four nonlinear concentrated springs near the four corners. The
restoring forces of the springs have cubic non-linearity and linear
component of the nonlinear springs has complex quantity to represent
linear hysteresis damping. The damping layer of the frame structures
has complex modulus of elasticity. Further, the discretized equations in
physical coordinate are transformed into the nonlinear ordinary
coupled differential equations using normal coordinate corresponding
to linear natural modes. Comparing shares of strain energy of the
elastic frame, the damping layer and the springs, we evaluate the
influences of the damping couplings on the linear and nonlinear impact
responses. We also investigate influences of damping changed by
stiffness of the elastic frame on the nonlinear coupling in the damped
impact responses.
Abstract: There is currently a gap in the technology covering the
rapid establishment of control after a reconfiguration in a
Reconfigurable Manufacturing System. This gap involves the
detection of the factory floor state and the communication link
between the factory floor and the high-level software. In this paper, a
thin, hardware-supported Middleware Management System (MMS) is
proposed and its design and implementation are discussed. The
research found that a cost-effective localization technique can be
combined with intelligent software to speed up the ramp-up of a
reconfigured system. The MMS makes the process more intelligent,
more efficient and less time-consuming, thus supporting the
industrial implementation of the RMS paradigm.
Abstract: An approach was evaluated for the retrieval of soil
moisture of bare soil surface using bistatic scatterometer data in the
angular range of 200 to 700 at VV- and HH- polarization. The
microwave data was acquired by specially designed X-band (10
GHz) bistatic scatterometer. The linear regression analysis was done
between scattering coefficients and soil moisture content to select the
suitable incidence angle for retrieval of soil moisture content. The 250
incidence angle was found more suitable. The support vector
regression analysis was used to approximate the function described
by the input output relationship between the scattering coefficient and
corresponding measured values of the soil moisture content. The
performance of support vector regression algorithm was evaluated by
comparing the observed and the estimated soil moisture content by
statistical performance indices %Bias, root mean squared error
(RMSE) and Nash-Sutcliffe Efficiency (NSE). The values of %Bias,
root mean squared error (RMSE) and Nash-Sutcliffe Efficiency
(NSE) were found 2.9451, 1.0986 and 0.9214 respectively at HHpolarization.
At VV- polarization, the values of %Bias, root mean
squared error (RMSE) and Nash-Sutcliffe Efficiency (NSE) were
found 3.6186, 0.9373 and 0.9428 respectively.
Abstract: Synthesis of gold nanoparticles has attracted much
attention since the pioneering discovery of the high catalytic activity
of supported gold nanoparticles in the reaction of CO oxidation at
low temperature. In this research field, we used Na-montmorillonite
for gold nanoparticles stabilization; various gold loading percentage
1, 2 and 5% were used for gold nanoparticles preparation. The gold
nanoparticles were obtained using chemical reduction method using
NaBH4 as reductant agent. The obtained gold nanoparticles stabilized
in Na-montmorillonite were used as catalysts for the reduction of 4-
nitrophenol to aminophenol with sodium borohydride at room
temperature. The UV-Vis results confirmed directly the gold
nanoparticles formation. The XRD and N2 adsorption results showed
the formation of gold nanoparticles in the pores of montmorillonite
with an average size of 5 nm obtained on samples with 2% gold
loading percentage. The gold particles size increased with the
increase of gold loading percentage. The reduction reaction of 4-
nitrophenol into 4-aminophenol with NaBH4 catalyzed by Au-Namontmorillonite
catalyst exhibits remarkably a high activity; the
reaction was completed within 9 min for 1%Au-Na-montmorillonite
and within 3 min for 2%Au-Na-montmorillonite.
Abstract: This paper applied factor conditions from Porter’s
Diamond Model (1990) to understand the various challenges facing
the AMISA. Factor conditions highlighted in Porter’s model are
grouped into two groups namely, basic and advance factors. Two
AMISA associations representing over 10 000 employees were
interviewed. The largest Clothing, Textiles and Leather (CTL)
apparel retail group was also interviewed with a government
department implementing the industrialization policy were
interviewed. The paper points out that AMISA have basic factor conditions
necessary for competitive advantage in the apparel industries.
However advance factor creation has proven to be a challenge for
AMISA, Higher Education Institutions (HEIs) and government. Poor
infrastructural maintenance has contributed to high manufacturing
costs and poor quick response technologies. The use of Porter’s
Factor Conditions as a tool to analyze the sector’s competitive
advantage challenges and opportunities has increased knowledge
regarding factors that limit the AMISA’s competitiveness. It is
therefore argued that other studies on Porter’s Diamond model
factors like Demand conditions, Firm strategy, structure and rivalry
and Related and supporting industries can be used to analyze the
situation of the AMISA for the purposes of improving competitive
advantage.
Abstract: Spacer grid assembly supporting the nuclear fuel rods
is an important concern in the design of structural components of a
Pressurized Water Reactor (PWR). The spacer grid is composed by
springs and dimples which are formed from a strip sheet by means of
blanking and stamping processes. In this paper, the blanking process
and tooling parameters are evaluated by means of a 2D plane-strain
finite element model in order to evaluate the punch load and quality
of the sheared edges of Inconel 718 strips used for nuclear spacer
grids. A 3D finite element model is also proposed to predict the
tooling loads resulting from the stamping process of a preformed
Inconel 718 strip and to analyse the residual stress effects upon the
spring and dimple design geometries of a nuclear spacer grid.
Abstract: Nine Degrees of Freedom (9 DOF) systems are
already in development in many areas. In this paper, an integrated
pressure sensor is proposed that will make use of an already existing
monolithic 9 DOF inertial MEMS platform. Capacitive pressure
sensors can suffer from limited sensitivity for a given size of
membrane. This novel pressure sensor design increases the sensitivity
by over 5 times compared to a traditional array of square diaphragms
while still fitting within a 2 mm x 2 mm chip and maintaining a fixed
static capacitance. The improved design uses one large diaphragm
supported by pillars with fixed electrodes placed above the areas of
maximum deflection. The design optimization increases the
sensitivity from 0.22 fF/kPa to 1.16 fF/kPa. Temperature sensitivity
was also examined through simulation.
Abstract: The aim of the present study is to investigate
consumers' determinants of intention toward the adoption of Smart
Grid solutions and technologies. Ajzen's Theory of Planned
Behaviour (TPB) model is applied and tested to explain the formation
of such adoption intention. An exogenous variable, taking into
account the resistance to change of individuals, was added to the
basic model. The elicitation study allowed obtaining salient modal
beliefs, which were used, with the support of literature, to design the
questionnaire. After the screening phase, data collected from the
main survey were analysed for evaluating measurement model's
reliability and validity. Consistent with the theory, the results of
structural equation analysis revealed that attitude, subjective norm,
and perceived behavioural control positively, which affected the
adoption intention. Specifically, the variable with the highest estimate
loading factor was found to be the perceived behavioural control,
and, the most important belief related to each construct was
determined (e.g., energy saving was observed to be the most
significant belief linked with attitude). Further investigation indicated
that the added exogenous variable has a negative influence on
intention; this finding confirmed partially the hypothesis, since this
influence was indirect: such relationship was mediated by attitude.
Implications and suggestions for future research are discussed.
Abstract: Nowadays, several research studies point up that an
active lifestyle is essential for physical and mental health benefits.
Mobile phones have greatly influenced people’s habits and attitudes
also in the way they exercise. Our research work is mainly focused on
investigating how to exploit mobile technologies to favour people’s
exertion experience. To this end, we developed an exertion framework
users can exploit through a real world mobile application, called
EverywhereSport Run (EWRun), designed to act as a virtual personal
trainer to support runners during their trainings. In this work, inspired
by both previous findings in the field of interaction design for people
with visual impairments, feedback gathered from real users of our
framework, and positive results obtained from two experimentations,
we present some new interaction facilities we designed to enhance
the interaction experience during a training. The positive obtained
results helped us to derive some interaction design recommendations
we believe will be a valid support for designers of future mobile
systems conceived to be used in circumstances where there are limited
possibilities of interaction.
Abstract: The enormous amount of information stored on the
web increases from one day to the next, exposing the web currently
faced with the inevitable difficulties of research pertinent information
that users really want. The problem today is not limited to expanding
the size of the information highways, but to design a system for
intelligent search. The vast majority of this information is stored in
relational databases, which in turn represent a backend for managing
RDF data of the semantic web. This problem has motivated us to
write this paper in order to establish an effective approach to support
semantic transformation algorithm for SPARQL queries to SQL
queries, more precisely SPARQL SELECT queries; by adopting this
method, the relational database can be questioned easily with
SPARQL queries maintaining the same performance.
Abstract: Plants can contain a wide variety of substances with
antioxidative properties which are associated with important health
benefits. These positive health effects are of great importance at a
time when the environment is laden with many toxic substances. Five
selected herbal plants namely, Mimosa pudica, Phyllanthus niruri,
Ceiba pentandra, Eleusine polydactyla and Trema amboinensi, were
chosen for the experiment to investigate their total phenolics content
and antioxidant activities using ABTS radical cation decolorization
power, and ferric reducing antioxidant power. The total phenolic
content of each herbal plants ranges from 0.84 to 42.59 mg gallic acid
equivalent/g. The antioxidant activity in the ABTS radical cation
decolorization power varies from 0.005 to 0.362 mg trolox
equivalent/g and the FRAP ranges from 0.30 to 28.42 mg gallic acid
equivalent/g. Among the five medicinal plants, Mimosa pudica has
been an excellent performer in terms of the 3 parameters measured; it
is followed by Phyllanthus niruri. The 5 herbal plants do not have
equivalent antioxidant power. The relative high values for M. pudica
and P. niruri supports the medicinal value of both plants. The total
phenolics, ABTS and FRAP correlate strongly with one another.
Abstract: Multiple User Interference (MUI) considers the
primary problem in Optical Code-Division Multiple Access
(OCDMA), which resulting from the overlapping among the users. In
this article we aim to mitigate this problem by studying an
interference cancellation scheme called successive interference
cancellation (SIC) scheme. This scheme will be tested on two
different detection schemes, spectral amplitude coding (SAC) and
direct detection systems (DS), using partial modified prime (PMP) as
the signature codes. It was found that SIC scheme based on both SAC
and DS methods had a potential to suppress the intensity noise, that is
to say it can mitigate MUI noise. Furthermore, SIC/DS scheme
showed much lower bit error rate (BER) performance relative to
SIC/SAC scheme for different magnitude of effective power. Hence,
many more users can be supported by SIC/DS receiver system.
Abstract: This paper presents an approach of on-line control of
the state of technosphere and environment objects based on the
integration of Data Warehouse, OLAP and Expert systems
technologies. It looks at the structure and content of data warehouse
that provides consolidation and storage of monitoring data. There is a
description of OLAP-models that provide a multidimensional
analysis of monitoring data and dynamic analysis of principal
parameters of controlled objects. The authors suggest some criteria of
emergency risk assessment using expert knowledge about danger
levels. It is demonstrated now some of the proposed solutions could
be adopted in territorial decision making support systems.
Operational control allows authorities to detect threat, prevent natural
and anthropogenic emergencies and ensure a comprehensive safety of
territory.
Abstract: The purpose of this study is to evaluate the English
version and a Malay translation of the 21-item Learner Awareness
Questionnaire for its application to assess student learning in higher
education. The Learner Awareness Questionnaire, originally written
in English, is a quantitative measure of how and why students learn.
The questionnaire gives an indication of the process and motives to
learn using four scales: survival, establishing stability, approval and
loving to learn. Data in the present study came from 680 university
students enrolled in various programmes in Malaysia. The Malay
version of the questionnaire supported a similar four factor structure
and internal consistency to the English version. The four factors of
the Malay version also showed moderate to strong correlations with
those of the English versions. The results suggest that the Malay
version of the questionnaire is similar to the English version.
However, further refinement to the questions is needed to strengthen
the correlations between the two questionnaires.
Abstract: DNA Barcode provides good sources of needed
information to classify living species. The classification problem has
to be supported with reliable methods and algorithms. To analyze
species regions or entire genomes, it becomes necessary to use the
similarity sequence methods. A large set of sequences can be
simultaneously compared using Multiple Sequence Alignment which
is known to be NP-complete. However, all the used methods are still
computationally very expensive and require significant computational
infrastructure. Our goal is to build predictive models that are highly
accurate and interpretable. In fact, our method permits to avoid the
complex problem of form and structure in different classes of
organisms. The empirical data and their classification performances
are compared with other methods. Evenly, in this study, we present
our system which is consisted of three phases. The first one, is called
transformation, is composed of three sub steps; Electron-Ion
Interaction Pseudopotential (EIIP) for the codification of DNA
Barcodes, Fourier Transform and Power Spectrum Signal Processing.
Moreover, the second phase step is an approximation; it is
empowered by the use of Multi Library Wavelet Neural Networks
(MLWNN). Finally, the third one, is called the classification of DNA
Barcodes, is realized by applying the algorithm of hierarchical
classification.
Abstract: Bicycle Level of Service (BLOS) is a measure for
evaluating street conditions for cyclists. Currently, various methods
are proposed for BLOS. These analytical methods however have
some drawbacks: they usually assume cyclists as users that can share
street facilities with motorized vehicles, it is not easy to link them to
design process and they are not easy to follow. In addition, they only
support a narrow range of cycling facilities and may not be applicable
for all situations. Along this, the current paper introduces various
effective design factors for bicycle-friendly streets. This study
considers cyclists as users of streets who have special needs and
facilities. Therefore, the key factors that influence BLOS based on
different cycling facilities that are proposed by developed guidelines
and literature are identified. The combination of these factors
presents a complete set of effective design factors for bicycle-friendly
streets. In addition, the weight of each factor in existing BLOS
models is estimated and these effective factors are ranked based on
these weights. These factors and their weights can be used in further
studies to propose special bicycle-friendly street design model.
Abstract: This paper describes a new approach which can be
used to interpret the experimental creep deformation data obtained
from miniaturized thin plate bending specimen test to the
corresponding uniaxial data based on an inversed application of the
reference stress method. The geometry of the thin plate is fully
defined by the span of the support, l, the width, b, and the thickness,
d. Firstly, analytical solutions for the steady-state, load-line creep
deformation rate of the thin plates for a Norton’s power law under
plane stress (b→0) and plane strain (b→∞) conditions were obtained,
from which it can be seen that the load-line deformation rate of the
thin plate under plane-stress conditions is much higher than that
under the plane-strain conditions. Since analytical solution is not
available for the plates with random b-values, finite element (FE)
analyses are used to obtain the solutions. Based on the FE results
obtained for various b/l ratios and creep exponent, n, as well as the
analytical solutions under plane stress and plane strain conditions, an
approximate, numerical solutions for the deformation rate are
obtained by curve fitting. Using these solutions, a reference stress
method is utilised to establish the conversion relationships between
the applied load and the equivalent uniaxial stress and between the
creep deformations of thin plate and the equivalent uniaxial creep
strains. Finally, the accuracy of the empirical solution was assessed
by using a set of “theoretical” experimental data.
Abstract: This paper investigates the parametric stability of an
axially moving web subjected to non-uniform in-plane edge
excitations on two opposite, simply-supported edges. The web is
modeled as a viscoelastic plate whose constitutive relation obeys the
Kelvin-Voigt model, and the in-plane edge excitations are expressed
as the sum of a static tension and a periodical perturbation. Due to the
in-plane edge excitations, the moving plate may bring about
parametric instability under certain situations. First, the in-plane
stresses of the plate due to the non-uniform edge excitations are
determined by solving the in-plane forced vibration problem. Then,
the dependence on the spatial coordinates in the equation of transverse
motion is eliminated by the generalized Galerkin method, which
results in a set of discretized system equations in time. Finally, the
method of multiple scales is utilized to solve the set of system
equations analytically if the periodical perturbation of the in-plane
edge excitations is much smaller as compared with the static tension of
the plate, from which the stability boundaries of the moving plate are
obtained. Numerical results reveal that only combination resonances
of the summed-type appear under the in-plane edge excitations
considered in this work.
Abstract: This paper directs attention to the limitations of the
teacher-centered strategy in teaching. The aim of this study is to draw
more educational attention to learner-centered strategy in order to
shift the emphasis from the traditional concept of teaching to a new
concept in teaching. To begin bridging the traditional concept of
teaching and the new concept, the study will explore the new concept
of teaching to support teaching in Arab World generally and in Iraq
specifically. A qualitative case study orientation was used to collect
data in the form of classroom observations, interviews and field
notes. The teaching practices used by three university instructors are
investigated and according to the findings, some explanations and
recommendations are made.
Abstract: Research Objectives: The roles and activities of
Human Resource Management (HRM) have changed a lot in the past
years. Driven by a changing environment and therefore new business
requirements, the scope of human resource (HR) activities has
widened. The extent to which these activities should focus on
strategic issues to support the long term success of a company has
been discussed in science for many years. As many economies of
Central and Eastern Europe (CEE) experienced a phase of transition
after the socialist era and are now recovering from the 2008 global
crisis it is needed to examine the current state of HR positioning.
Furthermore a trend in HR work developing from rather
administrative units to being strategic partners of management can be
noticed. This leads to the question of better understanding the
underlying competencies which are necessary to support
organisations. This topic was addressed by the international study
“HR Competencies in international comparison”. The quantitative
survey was conducted by the Institute for Human Resources &
Organisation of FHWien University of Applied Science of WKW (A)
in cooperation with partner universities in the countries Bosnia-
Herzegovina, Croatia, Serbia and Slovenia. Methodology: Using the
questionnaire developed by Dave Ulrich we tested whether the HR
Competency model can be used for Austria, Bosnia and Herzegovina,
Croatia, Serbia and Slovenia. After performing confirmatory and
exploratory factor analysis for the whole data set containing all five
countries we could clearly distinguish between four competencies. In
a further step our analysis focused on median and average
comparisons between the HR competency dimensions. Conclusion:
Our literature review, in alignment with other studies, shows a
relatively rapid pace of development of HR Roles and HR
Competencies in BCSS in the past decades. Comparing data from
BCSS and Austria we still can notice that regards strategic orientation
there is a lack in BCSS countries, thus competencies are not as
developed as in Austria. This leads us to the tentative conclusion that
HR has undergone a rapid change but is still in a State of Transition
from being a rather administrative unit to performing the role of a
strategic partner.