Abstract: The mechanical deformation and the electrical conductivity of lanthanum strontium cobalt ferrite oxide under uniaxial compression were investigated at various temperatures up to 1073 K. The material reveals a rather complex mechanical behaviour related to its ferroelasticity and completely different stress-strain curves are obtained during the 1st and 2nd loading cycles. A distinctive ferroelastic creep was observed at 293 K whilst typical ferroelastic stress-strain curve were obtained in the temperature range from 473 K to 873 K. At 1073 K, on the other hand, high-temperature creep deformation was observed instead of ferroelastic deformation. The conductivity increases with increasing compressive stress at all the temperatures. The increase in conductivity is related to both geometrical and piezoelectric effects. From 293 K to 873 K, where the material exhibits ferroelastic behaviour, the variation in the total conductivity decreases with increasing temperature. The contribution of the piezoelectric effect to the total conductivity variation also decreases with increasing temperature and the maximum in piezoconductivity has a value of about 0.75 % at 293 K for a compressive stress of 100 MPa. There is no effect of domain switching on conductivity except for the geometric effect. At 1073 K, the conductivity is simply proportional to the compressive strain.
Abstract: In this study rack systems that are structural storage
units of warehouses have been analyzed as structural with Finite
Element Method (FEA). Each cell of discussed rack system storages
pallets which have from 800 kg to 1000 kg weights and
0.80x1.15x1.50 m dimensions. Under this load, total deformations
and equivalent stresses of structural elements and principal stresses,
tensile stresses and shear stresses of connection elements have been
analyzed. The results of analyses have been evaluated according to
resistance limits of structural and connection elements. Obtained
results have been presented as visual and magnitude.
Abstract: In this paper, the techniques for estimating the
residual stress in high velocity oxy fuel thermal spray coatings have
been discussed and compared. The development trend and the last
investigation have been studied. It is seemed that the there is not
effective study on the effect of the peening action in HVOF
analytically and numerically.
Abstract: The seismic response of steel shear wall system considering nonlinearity effects using finite element method is investigated in this paper. The non-linear finite element analysis has potential as usable and reliable means for analyzing of civil structures with the availability of computer technology. In this research the large displacements and materially nonlinear behavior of shear wall is presented with developing of finite element code. A numerical model based on the finite element method for the seismic analysis of shear wall is presented with developing of finite element code in this research. To develop the finite element code, the standard Galerkin weighted residual formulation is used. Two-dimensional plane stress model and total Lagrangian formulation was carried out to present the shear wall response and the Newton-Raphson method is applied for the solution of nonlinear transient equations. The presented model in this paper can be developed for analysis of civil engineering structures with different material behavior and complicated geometry.
Abstract: To achieve accurate and precise results of finite
element analysis (FEA) of bones, it is important to represent the
load/boundary conditions as identical as possible to the human body
such as the bone properties, the type and force of the muscles, the
contact force of the joints, and the location of the muscle attachment.
In this study, the difference in the Von-Mises stress and the total
deformation was compared by classifying them into Case 1, which
shows the actual anatomical form of the muscle attached to the femur
when the same muscle force was applied, and Case 2, which gives a
simplified representation of the attached location. An inverse
dynamical musculoskeletal model was simulated using data from an
actual walking experiment to complement the accuracy of the
muscular force, the input value of FEA. The FEA method using the
results of the muscular force that were calculated through the
simulation showed that the maximum Von-Mises stress and the
maximum total deformation in Case 2 were underestimated by 8.42%
and 6.29%, respectively, compared to Case 1. The torsion energy and
bending moment at each location of the femur occurred via the stress
ingredient. Due to the geometrical/morphological feature of the femur
of having a long bone shape when the stress distribution is wide, as
shown in Case 1, a greater Von-Mises stress and total deformation are
expected from the sum of the stress ingredients. More accurate results
can be achieved only when the muscular strength and the attachment
location in the FEA of the bones and the attachment form are the same
as those in the actual anatomical condition under the various moving
conditions of the human body.
Abstract: The paper presents an analytical solution for dispersion
of a solute in the peristaltic motion of a couple stress fluid
through a porous medium with slip condition in the presence of both
homogeneous and heterogeneous chemical reactions. The average
effective dispersion coefficient has been found using Taylor-s limiting
condition and long wavelength approximation. The effects of various
relevant parameters on the average coefficient of dispersion have been
studied. The average effective dispersion coefficient tends to increase
with permeability parameter but tends to decrease with homogeneous
chemical reaction rate parameter, couple stress parameter, slip parameter
and heterogeneous reaction rate parameter.
Abstract: Linear stochastic estimation and quadratic stochastic
estimation techniques were applied to estimate the entire velocity
flow-field of an open cavity with a length to depth ratio of 2. The
estimations were done through the use of instantaneous velocity
magnitude as estimators. These measurements were obtained by
Particle Image Velocimetry. The predicted flow was compared
against the original flow-field in terms of the Reynolds stresses and
turbulent kinetic energy. Quadratic stochastic estimation proved to be
more superior than linear stochastic estimation in resolving the shear
layer flow. When the velocity fluctuations were scaled up in the
quadratic estimate, both the time-averaged quantities and the
instantaneous cavity flow can be predicted to a rather accurate extent.
Abstract: The plastic forming process of sheet plate takes an
important place in forming metals. The traditional techniques of tool
design for sheet forming operations used in industry are experimental
and expensive methods. Prediction of the forming results,
determination of the punching force, blank holder forces and the
thickness distribution of the sheet metal will decrease the production
cost and time of the material to be formed. In this paper, multi-stage
deep drawing simulation of an Industrial Part has been presented
with finite element method. The entire production steps with
additional operations such as intermediate annealing and springback
has been simulated by ABAQUS software under axisymmetric
conditions. The simulation results such as sheet thickness
distribution, Punch force and residual stresses have been extracted in
any stages and sheet thickness distribution was compared with
experimental results. It was found through comparison of results, the
FE model have proven to be in close agreement with those of
experiment.
Abstract: The cable tower of Liede Bridge is a double-column curved-lever arched-beam portal framed structure. Being novel and unique in structure, its cable tower differs in complexity from traditional ones. This paper analyzes the ultimate load capacity of cable tower by adopting the finite element calculations and model tests which indicate that constitutive relations applied here give a better simulation of actual failure process of prestressed reinforced concrete. In vertical load, horizontal load and overloading tests, the stepped loading of the tower model is of linear relationship, and the test data has good repeatability. All suggests that the cable tower has good bearing capacity, rational design and high emergency capacity.
Abstract: In view of geological origin, formation of the shallow
gas reservoir of the Hangzhou Bay, northern Zhejiang Province,
eastern China, and original occurrence characteristics of the gassy
sand are analyzed. Generally, gassy sand in scale gas reservoirs is in
the state of residual moisture content and the approximate scope of
initial matric suction of sand ranges about from 0kPa to100kPa.
Results based on GDS triaxial tests show that the classical shear
strength formulas of unsaturated soil can not effectively describe basic
strength characteristics of gassy sand; the relationship between
apparent cohesion and matric suction of gassy sand agrees well with
the power function, which can reasonably be used to describe the
strength of gassy sand. In the stress path of gas release, shear strength
of gassy sand will increase and experimental results show the formula
proposed in this paper can effectively predict the strength increment.
When saturated strength indexes of the sand are used in engineering
design, moderate reduction should be considered.
Abstract: An attempt was made to study of nitrogen
components response of corn (Zea mays L.) to drought stress. A farm
research was done in RCBD as split-plot with four replications in
Khorramabad, west Iran. Drought stress levels as irrigation regimes
after 75 (control), 100, and 120 (stress) mm cumulative evaporation
were in main plots, and four seed corn varieties include 500 (medium
maturity), 647, 700, and 704 (long maturity) were as subplots.
Soluble protein, nitrate and proline amino acid were measured in
shoot and root at flowering stage, and grain yield was measured in
harvesting stage. As the drought progressed, the amount of nitrate
and proline followed an increasing trend, but soluble protein
decreased in shoot and root. The highest amount of nitrate and
proline was observed in longer maturity varieties than shorter ones,
but decrease yield of long maturity varieties was higher than medium
maturity varieties in drought condition, because of long duration of
stress.
Abstract: Saffron (Crocus sativus) is cultivated as spices,
medicinal and aromatic plant species. At autumn season, heavy
rainfall can cause flooding stress and inhibits growth of saffron. Thus
this research was conducted to study the effect of silver ion (as an
ethylene inhibitor) on growth of saffron under flooding conditions.
The corms of saffron were soaked with one concentration of nano
silver (0, 40, 80 or 120 ppm) and then planting under flooding stress
or non flooding stress conditions. Results showed that number of
roots, root length, root fresh and dry weight, leaves fresh and dry
weight were reduced by 10 day flooding stress. Soaking saffron
corms with 40 or 80 ppm concentration of nano silver rewarded the
effect of flooding stress on the root number, by increasing it.
Furthermore, 40 ppm of nano silver increased root length in stress.
Nano silver 80 ppm in flooding stress, increased leaves dry weight.
Abstract: The aim of this work is to analyze a viscous flow in
the axisymmetric nozzle taken into account the mesh size both in the
free stream and into the boundary layer. The resolution of the Navier-
Stokes equations is realized by using the finite volume method to
determine the supersonic flow parameters at the exit of convergingdiverging
nozzle. The numerical technique uses the Flux Vector
Splitting method of Van Leer. Here, adequate time stepping
parameter, along with CFL coefficient and mesh size level is selected
to ensure numerical convergence. The effect of the boundary layer
thickness is significant at the exit of the nozzle. The best solution is
obtained with using a very fine grid, especially near the wall, where
we have a strong variation of velocity, temperature and shear stress.
This study enabled us to confirm that the determination of boundary
layer thickness can be obtained only if the size of the mesh is lower
than a certain value limits given by our calculations.
Abstract: Having considered tactile sensing and palpation of a
surgeon in order to detect kidney stone during open surgery; we
present the 2D model of nephrolithiasis (two dimensional model of
kidney containing a simulated stone). The effects of stone existence
that appear on the surface of kidney (because of exerting mechanical
load) are determined. Using Finite element method, it is illustrated
that the created stress patterns on the surface of kidney and stress
graphs not only show existence of stone inside kidney, but also show
its exact location.
Abstract: Real-time measurement of applied forces, like tension, compression, torsion, and bending moment, identifies the transferred energies being applied to the bottomhole assembly (BHA). These forces are highly detrimental to measurement/logging-while-drilling tools and downhole equipment. Real-time measurement of the dynamic downhole behavior, including weight, torque, bending on bit, and vibration, establishes a real-time feedback loop between the downhole drilling system and drilling team at the surface. This paper describes the numerical analysis of the strain data acquired by the measurement tool at different locations on the strain pockets. The strain values obtained by FEA for various loading conditions (tension, compression, torque, and bending moment) are compared against experimental results obtained from an identical experimental setup. Numerical analyses results agree with experimental data within 8% and, therefore, substantiate and validate the FEA model. This FEA model can be used to analyze the combined loading conditions that reflect the actual drilling environment.
Abstract: The current of professional bicycle pedal-s
manufacturing model mostly used casting, forging, die-casting
processing methods, so the paper used 7075 aluminum alloy which is
to produce the bicycle parts most commonly, and employs the
rigid-plastic finite element (FE) DEFORMTM 3D software to simulate
and to analyze the professional bicycle pedal design. First we use Solid
works 2010 3D graphics software to design the professional bicycle
pedal of the mold and appearance, then import finite element (FE)
DEFORMTM 3D software for analysis. The paper used rigid-plastic
model analytical methods, and assuming mode to be rigid body. A
series of simulation analyses in which the variables depend on
different temperature of forging billet, friction factors, forging speed,
mold temperature are reveal to effective stress, effective strain, damage
and die radial load distribution for forging bicycle pedal. The analysis
results hope to provide professional bicycle pedal forming mold
references to identified whether suit with the finite element results for
high-strength design suitability of aluminum alloy.
Abstract: Arc welding is an important joining process widely used in many industrial applications including production of automobile, ships structures and metal tanks. In welding process, the moving electrode causes highly non-uniform temperature distribution that leads to residual stresses and different deviations, especially buckling distortions in thin plates. In order to control the deviations and increase the quality of welded plates, a fixture can be used as a practical and low cost method with high efficiency. In this study, a coupled thermo-mechanical finite element model is coded in the software ANSYS to simulate the behavior of thin plates located by a 3-2-1 positioning system during the welding process. Computational results are compared with recent similar works to validate the finite element models. The agreement between the result of proposed model and other reported data proves that finite element modeling can accurately predict the behavior of welded thin plates.
Abstract: This paper deals with the problem of non-uniform
torsion in thin-walled elastic beams with asymmetric cross-section,
removing the basic concept of a fixed center of twist, necessary in the
Vlasov-s and Benscoter-s theories to obtain a warping stress field
equivalent to zero. In this new torsion/flexure theory, despite of the
classical ones, the warping function will punctually satisfy the first
indefinite equilibrium equation along the beam axis and it wont- be
necessary to introduce the classical congruence condition, to take into
account the effect of the beam restraints. The solution, based on the
Fourier development of the displacement field, is obtained assuming
that the applied external torque is constant along the beam axis and
on both beam ends the unit twist angle and the warping axial
displacement functions are totally restrained.
Finally, in order to verify the feasibility of the proposed method
and to compare it with the classical theories, two applications are
carried out. The first one, relative to an open profile, is necessary to
test the numerical method adopted to find the solution; the second
one, instead, is relative to a simplified containership section,
considered as full restrained in correspondence of two adjacent
transverse bulkheads.
Abstract: Brassinosteroids (BRs) regulate cell elongation,
vascular differentiation, senescence, and stress responses. BRs signal
through the BES1/BZR1 family of transcription factors, which
regulate hundreds of target genes involved in this pathway. In this
research a comprehensive genome-wide analysis was carried out in
BES1/BZR1 gene family in Arabidopsis thaliana, Cucumis sativus,
Vitis vinifera, Glycin max and Brachypodium distachyon.
Specifications of the desired sequences, dot plot and hydropathy plot
were analyzed in the protein and genome sequences of five plant
species. The maximum amino acid length was attributed to protein
sequence Brdic3g with 374aa and the minimum amino acid length
was attributed to protein sequence Gm7g with 163aa. The maximum
Instability index was attributed to protein sequence AT1G19350
equal with 79.99 and the minimum Instability index was attributed to
protein sequence Gm5g equal with 33.22. Aliphatic index of these
protein sequences ranged from 47.82 to 78.79 in Arabidopsis
thaliana, 49.91 to 57.50 in Vitis vinifera, 55.09 to 82.43 in Glycin
max, 54.09 to 54.28 in Brachypodium distachyon 55.36 to 56.83 in
Cucumis sativus. Overall, data obtained from our investigation
contributes a better understanding of the complexity of the
BES1/BZR1 gene family and provides the first step towards directing
future experimental designs to perform systematic analysis of the
functions of the BES1/BZR1 gene family.
Abstract: In the process of polyethylene extrusion polymer
material similar to powder or granule is under compression, melting
and transmission operation and on base of special form, extrudate has
been produced. Twin-screw extruders are applicable in industries
because of their high capacity. The powder mixing with chemical
additives and melting with thermal and mechanical energy in three
zones (feed, compression and metering zone) and because of gear
pump and screw's pressure, converting to final product in latest plate.
Extruders with twin-screw and short distance between screws are
better than other types because of their high capacity and good
thermal and mechanical stress.
In this paper, process of polyethylene extrusion and various tapes
of extruders are studied. It is necessary to have an exact control on
process to producing high quality products with safe operation and
optimum energy consumption.
The granule size is depending on granulator motor speed. Results
show at constant feed rate a decrease in granule size was found whit
Increase in motor speed. Relationships between HDPE feed rate and
speed of granulator motor, main motor and gear pump are calculated
following as:
x = HDPE feed flow rate, yM = Main motor speed
yM = (-3.6076e-3) x^4+ (0.24597) x^3+ (-5.49003) x^2+ (64.22092)
x+61.66786 (1)
x = HDPE feed flow rate, yG = Gear pump speed
yG = (-2.4996e-3) x^4+ (0.18018) x^3+ (-4.22794) x^2+ (48.45536)
x+18.78880 (2)
x = HDPE feed flow rate, y = Granulator motor speed
10th Degree Polynomial Fit: y = a+bx+cx^2+dx^3... (3)
a = 1.2751, b = 282.4655, c = -165.2098,
d = 48.3106, e = -8.18715, f = 0.84997
g = -0.056094, h = 0.002358, i = -6.11816e-5
j = 8.919726e-7, k = -5.59050e-9