Abstract: Vertical ZnO nanowire array films were synthesized
based on aqueous method for sensing applications. ZnO nanowires
were investigated structurally using X-ray diffraction (XRD) and
scanning electron microscopy (SEM). The gas-sensing properties of
ZnO nanowires array films are studied. It is found that the ZnO
nanowires array film sensor exhibits excellent sensing properties
towards O2 and CO2 at 100 °C with the response time shorter than 5
s. High surface area / volume ratio of vertical ZnO nanowire and high
mobility accounts for the fast response and recovery. The sensor
response was measured in the range from 100 to 500 ppm O2 and CO2
in this study.
Abstract: The article is aimed at bringing information on the scope and the level of use of talent management by organizations in one of the Czech Republic regions, in the Moravian-Silesian Region. On the basis of data acquired by a questionnaire survey it has been found out that organizations in the above-mentioned region are implementing the system of talent management on a small scale: this approach is used by 3.8 % of organizations only that is 9 from 237 (100 %) of the approached respondents. The main reasons why this approach is not used is either that organizations have no knowledge of it or there is lack of financial and personnel resources. In the article recommendations suggested by the author can be found for a wider application of talent management in the Czech practice.
Abstract: The use of electronic sensors in the electronics
industry has become increasingly popular over the past few years,
and it has become a high competition product. The frequency
adjustment process is regarded as one of the most important process
in the electronic sensor manufacturing process. Due to inaccuracies
in the frequency adjustment process, up to 80% waste can be caused
due to rework processes; therefore, this study aims to provide a
preliminary understanding of the role of parameters used in the
frequency adjustment process, and also make suggestions in order to
further improve performance. Four parameters are considered in this
study: air pressure, dispensing time, vacuum force, and the distance
between the needle tip and the product. A full factorial design for
experiment 2k was considered to determine those parameters that
significantly affect the accuracy of the frequency adjustment process,
where a deviation in the frequency after adjustment and the target
frequency is expected to be 0 kHz. The experiment was conducted on
two levels, using two replications and with five center-points added.
In total, 37 experiments were carried out. The results reveal that air
pressure and dispensing time significantly affect the frequency
adjustment process. The mathematical relationship between these
two parameters was formulated, and the optimal parameters for air
pressure and dispensing time were found to be 0.45 MPa and 458 ms,
respectively. The optimal parameters were examined by carrying out
a confirmation experiment in which an average deviation of 0.082
kHz was achieved.
Abstract: The Proton Exchange Membrane Fuel Cell (PEMFC)
control system has an important effect on operation of cell.
Traditional controllers couldn-t lead to acceptable responses because
of time- change, long- hysteresis, uncertainty, strong- coupling and
nonlinear characteristics of PEMFCs, so an intelligent or adaptive
controller is needed. In this paper a neural network predictive
controller have been designed to control the voltage of at the
presence of fluctuations of temperature. The results of
implementation of this designed NN Predictive controller on a
dynamic electrochemical model of a small size 5 KW, PEM fuel cell
have been simulated by MATLAB/SIMULINK.
Abstract: This study aims at investigating factors in research
and development (R&D) growth and exploring the role of R&D
management in enhancing social innovation and productivity
improvement in Iran-s industrial sector. It basically explores the
common types of R&D activities and the industries which benefited
the most from active R&D units in Iran. The researchers generated
qualitative analyses obtained from primary and secondary data.
The primary data have been retrieved through interviews with five
key players (Managing Director, Internal Manager, General Manager,
Executive Manager, and Project Manager) in the industrial sector.
The secondary data acquired from an investigation on Mazandaran, a
province of northern Iran. The findings highlight Iran-s focuses of R
& D on cost reduction and upgrading productivity. Industries that
have benefited the most from active R&D units are metallic,
machinery and equipment design, and automotive.
We rank order the primary effects of R&D on productivity
improvement as follows, industry improvement, economic growth,
using professional human resources, generating productivity and
creativity culture, creating a competitive and innovative environment,
and increasing people-s knowledge.
Generally, low budget dedication and insufficient supply of highly
skilled scientists and engineers are two important obstacles for R&D
in Iran. Whereas, R&D has resulted in improvement in Iranian
society, transfer of contemporary knowledge into the international
market is still lacking.
Abstract: In this paper, the action research driven design of a
context relevant, developmental peer review of teaching model, its
implementation strategy and its impact at an Australian university is
presented. PRO-Teaching realizes an innovative process that
triangulates contemporaneous teaching quality data from a range of
stakeholders including students, discipline academics, learning and
teaching expert academics, and teacher reflection to create reliable
evidence of teaching quality. Data collected over multiple classroom
observations allows objective reporting on development differentials
in constructive alignment, peer, and student evaluations. Further
innovation is realized in the application of this highly structured
developmental process to provide summative evidence of sufficient
validity to support claims for professional advancement and learning
and teaching awards. Design decision points and contextual triggers
are described within the operating domain. Academics and
developers seeking to introduce structured peer review of teaching
into their organization will find this paper a useful reference.
Abstract: This paper presents an inexpensive and effective temperature-controlled chamber for temperature environment tests of Organic Light Emitting Diode (OLED) panels. The proposed chamber is a compact warmer and cooler with an exact temperature control system. In the temperature-controlled space of the chamber, thermoelectric modules (TEMs) are utilized to cool or to heat OLED panels, novel fixtures are designed to flexibly clamp the OLED panels of different size, and special connectors for wiring between the OLED panels and the test instrument are supplied. The proposed chamber has the following features. (1) The TEMs are solid semi-conductive devices, so they operate without noise and without pollution. (2) The volume of the temperature-controlled space of the chamber about 160mm*160mm*120mm, so the chamber are compact and easy to move. (3) The range of the controlled temperatures is from -10 oC to +80 oC, and the precision is ?0.5 oC. (4) The test instrument can conveniently and easily measure the OLED panels via the novel fixtures and special connectors. In addition to a constant temperature being maintained in the chamber, a temperature shock experiments can run for a long time. Therefore, the chamber will be convenient and useful for temperature environment tests of OLED panels.
Abstract: The purposes of this study were as follows to evaluate
the economic value of Phu Kradueng National Park by the travel cost
method (TCM) and the contingent valuation method (CVM) and to
estimate the demand for traveling and the willingness to pay. The
data for this study were collected by conducting two large scale
surveys on users and non-users. A total of 1,016 users and 1,034
non-users were interviewed. The data were analyzed using multiple
linear regression analysis, logistic regression model and the
consumer surplus (CS) was the integral of demand function for trips.
The survey found, were as follows:
1)Using the travel cost method which provides an estimate of direct
benefits to park users, we found that visitors- total willingness to pay
per visit was 2,284.57 bath, of which 958.29 bath was travel cost,
1,129.82 bath was expenditure for accommodation, food, and
services, and 166.66 bath was consumer surplus or the visitors -net
gain or satisfaction from the visit (the integral of demand function for
trips).
2) Thai visitors to Phu Kradueng National Park were further willing
to pay an average of 646.84 bath per head per year to ensure the
continued existence of Phu Kradueng National Park and to preserve
their option to use it in the future.
3) Thai non-visitors, on the other hand, are willing to pay an average
of 212.61 bath per head per year for the option and existence value
provided by the Park.
4) The total economic value of Phu Kradueng National Park to Thai
visitors and non-visitors taken together stands today at 9,249.55
million bath per year.
5) The users- average willingness to pay for access to Phu Kradueng
National Park rises
from 40 bath to 84.66 bath per head per trip for improved services
such as road improvement, increased cleanliness, and upgraded
information.
This paper was needed to investigate of the potential market
demand for bio prospecting in Phu Kradueng national Park and to
investigate how a larger share of the economic benefits of tourism
could be distributed income to the local residents.
Abstract: This paper is described one of the intelligent control method in Autonomous systems, which is called fuzzy control to correct the three wheel omnidirectional robot movement while it make mistake to catch the target. Fuzzy logic is especially advantageous for problems that can not be easily represented by mathematical modeling because data is either unavailable, incomplete or the process is too complex. Such systems can be easily up grated by adding new rules to improve performance or add new features. In many cases , fuzzy control can be used to improve existing traditional controller systems by adding an extra layer of intelligence to the current control method. The fuzzy controller designed here is more accurate and flexible than the traditional controllers. The project is done at MRL middle size soccer robot team.
Abstract: In this paper, multilayered coreless printed circuit
board (PCB) step-down power transformers for DC-DC converter
applications have been designed, manufactured and evaluated. A set
of two different circular spiral step-down transformers were
fabricated in the four layered PCB. These transformers have been
modelled with the assistance of high frequency equivalent circuit and
characterized with both sinusoidal and square wave excitation. This
paper provides the comparative results of these two different
transformers in terms of their resistances, self, leakage, mutual
inductances, coupling coefficient and also their energy efficiencies.
The operating regions for optimal performance of these transformers
for power transfer applications are determined. These transformers
were tested for the output power levels of about 30 Watts within the
input voltage range of 12-50 Vrms. The energy efficiency for these
step down transformers is observed to be in the range of 90%-97% in
MHz frequency region.
Abstract: Currently, the demand for marine and fisheries commodity in Yogyakarta, Indonesia continues to increase. The existing condition shows that the aquaculture supply cannot be supplied by Yogyakarta region itself, but still need to be supported by regions outside Yogyakarta. The effort to optimize the market is initiated by reviewing and designing the supply chain of production and trade of aquaculture commodity in order to create the implementation of aquaculture production and trade commodity optimally. This formulated supply chain model indicates 4 performance indicators of measurable success in terms of: (1) efficiency; (2) flexibility; (3) responsiveness; and (4) quality. These indicators had been exercised as the success benchmarks for priority marketing management in local level as well as national level. The result of this research indicates that if the catfish fishery system is managed as business as usual then the catfish demand in Yogyakarta region will experience to increase in the future. The increase of demand is inline with the increase of number of people in Yogyakarta and also the fluctuation of catfish consumption per capita. The highest production of catfish will experience in the third year approximately 30,118 tons. Other result of the research indicates that the catfish demand in Yogyakarta region cannot be supplied yet from the local region. Therefore, to fulfill the supply from outside Yogyakarta region, the local farmers should improve the supply through land extension. The fluctuation of commodity price will experience in the future annually and the catfish supply from outside Yogyakarta region will be lowering the price in the market.
Abstract: This study comprehensively simulate the use of k-ε
model for predicting flow and heat transfer with measured flow field
data in a stationary duct with elucidates on the detailed physics
encountered in the fully developed flow region, and the sharp 180°
bend region. Among the major flow features predicted with accuracy
are flow transition at the entrance of the duct, the distribution of
mean and turbulent quantities in the developing, fully developed, and
sharp 180° bend, the development of secondary flows in the duct
cross-section and the sharp 180° bend, and heat transfer
augmentation. Turbulence intensities in the sharp 180° bend are
found to reach high values and local heat transfer comparisons show
that the heat transfer augmentation shifts towards the wall and along
the duct. Therefore, understanding of the unsteady heat transfer in
sharp 180° bends is important. The design and simulation are related
to concept of fluid mechanics, heat transfer and thermodynamics.
Simulation study has been conducted on the response of turbulent
flow in a rectangular duct in order to evaluate the heat transfer rate
along the small scale multiple rectangular duct
Abstract: Load balancing is the process of improving the
performance of a parallel and distributed system through a
redistribution of load among the processors [1] [5]. In this paper we
present the performance analysis of various load balancing
algorithms based on different parameters, considering two typical
load balancing approaches static and dynamic. The analysis indicates
that static and dynamic both types of algorithm can have
advancements as well as weaknesses over each other. Deciding type
of algorithm to be implemented will be based on type of parallel
applications to solve. The main purpose of this paper is to help in
design of new algorithms in future by studying the behavior of
various existing algorithms.
Abstract: In this paper, we consider Wiener nonlinear model for solid oxide fuel cell (SOFC). The Wiener model of the SOFC consists of a linear dynamic block and a static output non-linearity followed by the block, in which linear part is approximated by state-space model and the nonlinear part is identified by a polynomial form. To control the SOFC system, we have to consider various view points such as operating conditions, another constraint conditions, change of load current and so on. A change of load current is the significant one of these for good performance of the SOFC system. In order to keep the constant stack terminal voltage by changing load current, the nonlinear model predictive control (MPC) is proposed in this paper. After primary control method is designed to guarantee the fuel utilization as a proper constant, a nonlinear model predictive control based on the Wiener model is developed to control the stack terminal voltage of the SOFC system. Simulation results verify the possibility of the proposed Wiener model and MPC method to control of SOFC system.
Abstract: This paper reports on the results of experimental
investigations of flash evaporation from superheated jet issues
vertically upward from a round straight nozzle of 81.3 mm diameter.
For the investigated range of jet superheat degree and velocity, it was
shown that flash evaporation enhances with initial temperature
increase. Due to the increase of jet inertia and subsequently the delay
of jet shattering, increase of jet velocity was found to result in
increase of evaporation "delay period". An empirical equation
predicts the jet evaporation completion height was developed, this
equation is thought to be useful in designing the flash evaporation
chamber. In attempts for enhancement of flash evaporation, use of
steel wire mesh located at short distance downstream was found
effective with no consequent pressure drop.
Abstract: This paper examines the problem of designing robust H controllers for for HIV/AIDS infection system with dual drug dosages described by a Takagi-Sugeno (S) fuzzy model. Based on a linear matrix inequality (LMI) approach, we develop an H controller which guarantees the L2-gain of the mapping from the exogenous input noise to the regulated output to be less than some prescribed value for the system. A sufficient condition of the controller for this system is given in term of Linear Matrix Inequalities (LMIs). The effectiveness of the proposed controller design methodology is finally demonstrated through simulation results. It has been shown that the anti-HIV vaccines are critically important in reducing the infected cells.
Abstract: A closed-loop controlled wireless power transmission circuit block for implantable biomedical applications is described in this paper. The circuit consists of one front-end rectifier, power management sub-block including bandgap reference and low drop-out regulators (LDOs) as well as transmission power detection / feedback circuits. Simulation result shows that the front-end rectifier achieves 80% power efficiency with 750-mV single-end peak-to-peak input voltage and 1.28-V output voltage under load current of 4 mA. The power management block can supply 1.8mA average load current under 1V consuming only 12μW power, which is equivalent to 99.3% power efficiency. The wireless power transmission block described in this paper achieves a maximum power efficiency of 80%. The wireless power transmission circuit block is designed and implemented using UMC 65-nm CMOS/RF process. It occupies 1 mm × 1.2 mm silicon area.
Abstract: Functional Magnetic Resonance Imaging(fMRI) is a
noninvasive imaging technique that measures the hemodynamic
response related to neural activity in the human brain. Event-related
functional magnetic resonance imaging (efMRI) is a form of
functional Magnetic Resonance Imaging (fMRI) in which a series of
fMRI images are time-locked to a stimulus presentation and averaged
together over many trials. Again an event related potential (ERP) is a
measured brain response that is directly the result of a thought or
perception. Here the neuronal response of human visual cortex in
normal healthy patients have been studied. The patients were asked
to perform a visual three choice reaction task; from the relative
response of each patient corresponding neuronal activity in visual
cortex was imaged. The average number of neurons in the adult
human primary visual cortex, in each hemisphere has been estimated
at around 140 million. Statistical analysis of this experiment was
done with SPM5(Statistical Parametric Mapping version 5) software.
The result shows a robust design of imaging the neuronal activity of
human visual cortex.
Abstract: Experimental investigation has been carried out
towards understanding the complex fluid dynamics involved in the
interaction of vortical structures with zero pressure gradient boundary
layer. A laminar boundary layer is produced on the flat plate placed
in the water flume and the synthetic jet actuator is deployed on top of
the plate at a definite distance from the leading edge. The synthetic
jet actuator has been designed in such a way that the to and fro
motion of the diaphragm is maneuvered at will by varying the
operating parameters to produce the typical streamwise vortical
structures namely hairpin and tilted vortices. PIV measurements are
made on the streamwise plane normal to the plate to evaluate their
interaction with the near wall fluid.
Abstract: In order to improve the simulation effects of space cold
black environment, this paper described a rectangular channel plate
heat sink. By using fluid mechanics theory and finite element method,
the internal fluid flow and heat transfer in heat sink was numerically
simulated to analyze the impact of channel structural on fluid flow and
heat transfer. The result showed that heat sink temperature uniformity
is well, and the impact of channel structural on the heat sink
temperature uniformity is not significant. The channel depth and
spacing are important factors which affect the fluid flow and heat
transfer in the heat sink. The two factors of heat transfer and resistance
need to be considered comprehensively to determine the optimal flow
structure parameters.