Abstract: There has been a growing interest in the oxygenation
by plunging water jets in the last few years due to their inherent
advantages, like energy-efficient, low operation cost, etc. Though a
lot of work has been reported on the oxygen-transfer by single
plunging water jets but very few studies have been carried out using
multiple plunging jets. In this paper, volumetric oxygen-transfer
coefficient and oxygen-transfer efficiency has been studied
experimentally for multiple inclined plunging jets (having jet plunge
angle of 60 0 ) in a pool of water for different configurations, in
terms of varying number of jets and jet diameters. This research
suggests that the volumetric oxygen-transfer coefficient and oxygentransfer
efficiency of the multiple inclined plunging jets for air-water
system are significantly higher than those of a single vertical as well
as inclined plunging jet for same flow area and other similar
conditions. The study also reveals that the oxygen-transfer increase
with increase in number of multiple jets under similar conditions,
which will be most advantageous and energy-efficient in practical
situations when large volumes of wastewaters are to be treated. A
relationship between volumetric oxygen-transfer coefficient and jet
parameters is also proposed. The suggested relationship predicts the
volumetric oxygen-transfer coefficient for multiple inclined plunging
jet(s) within a scatter of ±15 percent. The relationship will be quite
useful in scale-up and in deciding optimum configuration of multiple
inclined plunging jet aeration system.
Abstract: Pleurotus ostreatus is a common edible mushroom with a number of properties that can help to solve the nutritional and economical problems of people in Chiapas, Mexico. The objective of this project was to produce the mushroom under a sustainable management in which only regional products were allowed as a way to promote the cultivation and consumption of Pleurotus ostreatus; 5 different substrates were tested as well as 2 sanitation methods. The obtained results showed that the highest yields were obtained using corn husk and a thermal sanitation method. Pests and diseases were not a problem during the project but they appeared more in the substrates sanitized with calcium hydroxide.
Abstract: In a field experiment, growth parameters of soybean
cultivars in different weeding regimes was investigated. The trial was
split plot in a randomized complete block design. The four cultivars
and two lines of soybean (Glycine max L.) including: Sahar, Hill,
Sari, Telar, 032 and 033 in main plot and weeding regime consist of
no weeding (control), one weeding (35 days after planting) and two
weeding (35+20 days after planting) were randomized in sub plot.
The results showed that during the growth season 033 had the highest
dry matter in two weeding. In two weeding regime the dry matter
decreased. ). In all weeding regimes 033 had the highest CGR (Figs.
3a, 3b and 3c), which cleared this cultivar ability compare to the
others. This cultivar by increasing its leaf area could do more
photosynthesis, so, have a higher CGR.
Abstract: Decision support systems are usually based on
multidimensional structures which use the concept of hypercube.
Dimensions are the axes on which facts are analyzed and form a
space where a fact is located by a set of coordinates at the
intersections of members of dimensions. Conventional
multidimensional structures deal with discrete facts linked to discrete
dimensions. However, when dealing with natural continuous
phenomena the discrete representation is not adequate. There is a
need to integrate spatiotemporal continuity within multidimensional
structures to enable analysis and exploration of continuous field data.
Research issues that lead to the integration of spatiotemporal
continuity in multidimensional structures are numerous. In this paper,
we discuss research issues related to the integration of continuity in
multidimensional structures, present briefly a multidimensional
model for continuous field data. We also define new aggregation
operations. The model and the associated operations and measures
are validated by a prototype.
Abstract: This study, focusing on the importance of encouraging
outdoor activities for children, aims to propose and implement a
Web-GIS based outdoor education program for elementary schools,
which will then be evaluated by users. Specifically, for the purpose of
improved outdoor activities in the elementary school education, the
outdoor education program, with chiefly using the Web-GIS that
provides a good information provision and sharing tool, is proposed
and implemented before being evaluated by users. Conclusions of the
study boil down to:
(1) An eight-staged outdoor education program based on the Web-GIS
was proposed for a “second school" of an elementary school that
was then implemented before being evaluated by users (teachers,
instructors, students, and their parents).
(2) The program generally received a good evaluation, while a lot of
students and their parents evaluated negatively for the degree of
discovery and for the degree of interest, respectively, in the
questionnaire survey of students and their parents conducted after
the “second school". The surveys clearly show that an issue to be
solved, from the viewpoint of teachers in particular, is the
establishment of the GIS that will easily represent teaching materials
developed by teachers and of Web-GIS, and improved significance
of the use of GIS and Web-GIS for their widespread.
Abstract: Feature-based registration is an effective technique for clinical use, because it can greatly reduce computational costs. However, this technique, which estimates the transformation by using feature points extracted from two images, may cause misalignments. To handle with this limitation, we propose to extract the salient edges and extracted control points (CP) of medical images by using efficiency of multiresolution representation of data nonsubsampled contourlet transform (NSCT) that finds the best feature points. The MR images were first decomposed using the NSCT, and then Edge and CP were extracted from bandpass directional subband of NSCT coefficients and some proposed rules. After edge and CP extraction, mutual information was adopted for the registration of feature points and translation parameters are calculated by using particle swarm optimization (PSO). The experimental results showed that the proposed method produces totally accurate performance for registration medical CT-MR images.
Abstract: ebXML (Electronic Business using eXtensible
Markup Language) is an e-business standard, sponsored by
UN/CEFACT and OASIS, which enables enterprises to exchange
business messages, conduct trading relationships, communicate
data in common terms and define and register business
processes. While there is tremendous e-business value in the
ebXML, security remains an unsolved problem and one of the
largest barriers to adoption. XML security technologies emerging
recently have extensibility and flexibility suitable for security
implementation such as encryption, digital signature, access
control and authentication.
In this paper, we propose ebXML business transaction models
that allow trading partners to securely exchange XML based
business transactions by employing XML security technologies.
We show how each XML security technology meets the ebXML
standard by constructing the test software and validating messages
between the trading partners.
Abstract: A lot of matching algorithms with different characteristics have been introduced in recent years. For real time systems these algorithms are usually based on minutiae features. In this paper we introduce a novel approach for feature extraction in which the extracted features are independent of shift and rotation of the fingerprint and at the meantime the matching operation is performed much more easily and with higher speed and accuracy. In this new approach first for any fingerprint a reference point and a reference orientation is determined and then based on this information features are converted into polar coordinates. Due to high speed and accuracy of this approach and small volume of extracted features and easily execution of matching operation this approach is the most appropriate for real time applications.
Abstract: For best collaboration, Asynchronous tools and particularly the discussion forums are the most used thanks to their flexibility in terms of time. To convey only the messages that belong to a theme of interest of the tutor in order to help him during his tutoring work, use of a tool for classification of these messages is indispensable. For this we have proposed a semantics classification tool of messages of a discussion forum that is based on LSA (Latent Semantic Analysis), which includes a thesaurus to organize the vocabulary. Benefits offered by formal ontology can overcome the insufficiencies that a thesaurus generates during its use and encourage us then to use it in our semantic classifier. In this work we propose the use of some functionalities that a OWL ontology proposes. We then explain how functionalities like “ObjectProperty", "SubClassOf" and “Datatype" property make our classification more intelligent by way of integrating new terms. New terms found are generated based on the first terms introduced by tutor and semantic relations described by OWL formalism.
Abstract: This paper presents the design, development and characterization of contractile water jet thruster (CWJT) for mini underwater robot. Instead of electric motor, this CWJT utilizes the Ionic Polymer Metal Composite (IPMC) as the actuator to generate the water jet. The main focus of this paper is to analyze the conceptual design of the proposed CWJT which would determine the thrust force value, jet flow behavior and actuator’s stress. Those thrust force and jet flow studies were carried out using Matlab/Simscape simulation software. The actuator stress had been analyzed using COSMOS simulation software. The results showed that there was no significant change for jet velocity at variable cross sectional nozzle area. However, a significant change was detected for jet velocity at different nozzle cross sectional area ratio which was up to 37%. The generated thrust force has proportional relation to the nozzle cross sectional area.
Abstract: The direct sewage sludge application is a relative
cheap method for their liquidation. In the past heavy metal contents
increase in soils treated with sewage sludge was observed. In 2003
there was acceptance on act n.188/2003 about sewage sludge
application on soils. The basic philosophy of act is a safety of the
environmental proof of sludge application on soils. The samples of
soils from wastewater treatment plant (WTP) Poprad (35) and WTP
Michalovce (33 samples) were analyzed which were chosen for
sludge application on soils. According to the results only 14 areas for
Poprad and 25 areas for Michalovce are suitable for sludge
application according to act No. 188/2003. The application dose of
sludge was calculated 50 t.ha-1 or 75 t. ha-1 once in 5 years to ensure
that heavy metal contents in treated soils will be kept.
Abstract: Carriers scattering in the inversion channel of n-
MOSFET dominates the drain current. This paper presents an effective
electron mobility model for the pocket implanted nano scale
n-MOSFET. The model is developed by using two linear pocket
profiles at the source and drain edges. The channel is divided into
three regions at source, drain and central part of the channel region.
The total number of inversion layer charges is found for these three
regions by numerical integration from source to drain ends and the
number of depletion layer charges is found by using the effective
doping concentration including pocket doping effects. These two
charges are then used to find the effective normal electric field,
which is used to find the effective mobility model incorporating the
three scattering mechanisms, such as, Coulomb, phonon and surface
roughness scatterings as well as the ballistic phenomena for the
pocket implanted nano-scale n-MOSFET. The simulation results show
that the derived mobility model produces the same results as found
in the literatures.
Abstract: Although, it is a long time that human know about
the importance of environment in life, but at the last decade of 20
century, the space that was full of hot scientific, collegial and
political were made in environmental challenge, So much that, this
problem not only disarrange the peace and security of life, but also it
has threatened human existence. One of the problems in last years
that are significant for authorities is unsatisfactory achieved results
against of using huge cost for magnificent environmental projects.
This subject leads thinker to this thought that for solving the
environmental problems it is needed new methods include of
sociology, ethics and philosophic, etc. methods apart of technical
affairs. Environment ethics is a new branch of philosophic ethics
discussion that discusses about the ethics relationship between
humans and universe that is around them. By notifying to the above
considered affairs, in today world, necessity of environmental ethics
for environment management is reduplicated. In the following the
article has been focused on environmental ethics role and
environmental management methods and techniques for developing
it.
Abstract: At the end of the 20th century it was actual the
development of transport corridors and the improvement of their
technical parameters. With this purpose, many countries and Georgia
among them manufacture to construct new highways, railways and
also reconstruction-modernization of the existing transport
infrastructure. It is necessary to explore the artificial structures
(bridges and tunnels) on the existing tracks as they are very old.
Conference report includes the peculiarities of reconstruction of
tunnels, because we think that this theme is important for the
modernization of the existing road infrastructure. We must remark
that the methods of determining mining pressure of tunnel
reconstructions are worked out according to the jobs of new tunnels
but it is necessary to foresee additional mining pressure which will be
formed during their reconstruction. In this report there are given the
methods of figuring the additional mining pressure while
reconstruction of tunnels, there was worked out the computer
program, it is determined that during reconstruction of tunnels the
additional mining pressure is 1/3rd of main mining pressure.
Abstract: The quality improvements of the environmental
elements could increase the recreational opportunities in a certain
area (destination). The technique of the need for recreation focuses
on choosing certain destinations for recreational purposes. The basic
exchange taken into consideration is the one between the satisfaction
gained after staying in that area and the value expressed in money
and time allocated. The number of tourists in the respective area, the
duration of staying and the money spent including transportation
provide information on how individuals rank the place or certain
aspects of the area (such as the quality of the environmental
elements).
For the statistical analysis of the environmental benefits offered by
an area through the need of recreation technique, the following stages
are suggested:
- characterization of the reference area based on the
statistical variables considered;
- estimation of the environmental benefit through
comparing the reference area with other similar areas
(having the same environmental characteristics), from
the perspective of the statistical variables considered.
The model compared in recreation technique faced with a series of
difficulties which refers to the reference area and correct
transformation of time in money.
Abstract: This paper proposes rough set models with three
different level knowledge granules in incomplete information system
under tolerance relation by similarity between objects according to
their attribute values. Through introducing dominance relation on the
discourse to decompose similarity classes into three subclasses: little
better subclass, little worse subclass and vague subclass, it dismantles
lower and upper approximations into three components. By using
these components, retrieving information to find naturally hierarchical
expansions to queries and constructing answers to elaborative queries
can be effective. It illustrates the approach in applying rough set
models in the design of information retrieval system to access different
granular expanded documents. The proposed method enhances rough
set model application in the flexibility of expansions and elaborative
queries in information retrieval.
Abstract: Alpinia galanga is rhizome, generally known as
Greater galangal and is selected for isolation of newer constituents
accountable for various therapeutic activities. Present study is
intended to isolate glycoside from Alpinia galanga rhizomes. Alpinia
galanga methanolic extract was column chromatograph and eluted
with ethyl acetate-methanol (99:1) to isolate compound β-Sitosterol
Diarabinoside. Herein, the isolation and structural elucidation of new
compound is described. Chemical investigation of methanolic extract
of rhizomes of Alpinia galanga furnished a new compound β-
Sitosterol Diarabinoside. The IR, NMR and MASS investigations of
isolated compound confirmed its structure as β-Sitosterol
Diarabinoside, which is isolated for the first time from a medicinal
plant or any synthetic source.
Abstract: Bubble generation was observed using a high-speed
camera in subcooled flow boiling at low void fraction. Constant heat
flux was applied on one side of an upward rectangular channel to
make heated test channel. Water as a working fluid from high
subcooling to near saturation temperature was injected step by step to
investigate bubble behavior during void development. Experiments
were performed in two different pressures condition close to 2bar and
4bar. It was observed that in high subcooling when boiling was
commenced, bubble after nucleation departed its origin and slid
beside heated surface. In an observation window mean release
frequency of bubble fb,mean, nucleation site Ns and mean bubble
volume Vb,mean in each step of experiments were measured to
investigate wall vaporization rate. It was found that in proximity of
PNVG vaporization rate was increased significantly in compare with
condensation rate which remained in low value.
Abstract: Low-carbon economy means the energy conservation and emission reduction. How to measure and evaluate the regional low-carbon economy is an important problem which should be solved immediately. This paper proposed the eco-efficiency ratio based on the ecological efficiency to evaluate the current situation of the low-carbon economy in Jiangsu province and to analyze the efficiency of the low-carbon economy in Jiangsu and other provinces, compared both advantages and disadvantages. And then this paper put forward some advices for the government to formulate the correct development policy of low-carbon economy, to improve the technology innovation capacity and the efficiency of resource allocation.
Abstract: Shirvan is located in plain in Northern Khorasan province north east of Iran and has semiarid to temperate climate. To investigate the annual changes in some qualitative parameters such as electrical conductivity, total dissolved solids and chloride concentrations which have increased during ten continuous years. Fourteen groundwater sources including deep as well as semi-deep wells were sampled and were analyzed using standard methods. The trends of obtained data were analyzed during these years and the effects of different factors on the changes in electrical conductivity, concentration of chloride and total dissolved solids were clarified. The results showed that the amounts of some qualitative parameters have been increased during 10 years time which has led to decrease in water quality. The results also showed that increased in urban populations as well as extensive industrialization in the studied area are the most important reasons to influence underground water quality. Furthermore decrease in water quantity is also evident due to more water utilization and occurrence of recent droughts in the region during recent years.