Abstract: The Build-Then-Sell (BTS) is a novel system
implemented in Malaysia after a number of complaints have been
received from buyers in the preceding Sell-Then-Build (STB) system.
When the government announced the implementation of the BTS in
2007, proponents of BTS have asserted that the new system will
provide houses with low level of defects. Their argument however is
not supported by any empirical data. Hence, this study is conducted
to evaluate the housing defects in BTS houses. Six BTS residential
areas have been surveyed to collect the defects data. Questionnaires
were administered directly to the occupiers in each of the BTS houses
through door-to-door visits. The result has shown that the rate of
defects for the six residential areas is ranged from minor to slight,
which only affect the aesthetic value of the house.
Abstract: In recent years, there has been an increasing interest in using daylight to save energy in buildings. In tropical regions, daylighting is always an energy saver. On the other hand, daylight provides visual comfort. According to standards, it shows that many criteria should be taken into consideration in order to have daylight utilization and visual comfort. The current standard in Malaysia, MS 1525 does not provide sufficient guideline. Hence, more research is needed on daylight performance. If architects do not consider daylight design, it not only causes inconvenience in working spaces but also causes more energy consumption as well as environmental pollution. This research had surveyed daylight performance in 5 selected office buildings from different area of Malaysian through experimental method. Several parameters of daylight quality such as daylight factor, surface luminance and surface luminance ratio were measured in different rooms in each building. The result of this research demonstrated that most of the buildings were not designed for daylight utilization. Therefore, it is very important that architects follow the daylight design recommendation to reduce consumption of electric power for artificial lighting while the sufficient quality of daylight is available.
Abstract: In this paper, for the first time, a two-dimensional
(2D) analytical drain current model for sub-100 nm multi-layered
gate material engineered trapezoidal recessed channel (MLGMETRC)
MOSFET: a novel design is presented and investigated using
ATLAS and DEVEDIT device simulators, to mitigate the large gate
leakages and increased standby power consumption that arise due to
continued scaling of SiO2-based gate dielectrics. The twodimensional
(2D) analytical model based on solution of Poisson-s
equation in cylindrical coordinates, utilizing the cylindrical
approximation, has been developed which evaluate the surface
potential, electric field, drain current, switching metric: ION/IOFF
ratio and transconductance for the proposed design. A good
agreement between the model predictions and device simulation
results is obtained, verifying the accuracy of the proposed analytical
model.
Abstract: An effective approach for realizing the binary tree structure, representing a combinational logic functionality with enhanced throughput, is discussed in this paper. The optimization in maximum operating frequency was achieved through delay minimization, which in turn was possible by means of reducing the depth of the binary network. The proposed synthesis methodology has been validated by experimentation with FPGA as the target technology. Though our proposal is technology independent, yet the heuristic enables better optimization in throughput even after technology mapping for such Boolean functionality; whose reduced CNF form is associated with a lesser literal cost than its reduced DNF form at the Boolean equation level. For cases otherwise, our method converges to similar results as that of [12]. The practical results obtained for a variety of case studies demonstrate an improvement in the maximum throughput rate for Spartan IIE (XC2S50E-7FT256) and Spartan 3 (XC3S50-4PQ144) FPGA logic families by 10.49% and 13.68% respectively. With respect to the LUTs and IOBUFs required for physical implementation of the requisite non-regenerative logic functionality, the proposed method enabled savings to the tune of 44.35% and 44.67% respectively, over the existing efficient method available in literature [12].
Abstract: The impact of a proposed pier on tidal current
alteration was evaluated. The proposed pier location was in Salad
Bay on Koa Kood Island, Trat province, Thailand, and was designed
to accommodate passenger ships with a draft of less than 2 m. The
study began with collecting necessary data, including bathymetric,
water elevation and tidal current characteristics. The impact was
assessed using a software package (MIKE21). Although the results
showed that the pier would affect the existing current pattern, the
change was determined to be insignificant, as the design of the piles
for the pier provided sufficient spacing to let the current flow as
freely as possible. Consequences of the altered current, such as
seabed erosion, water stagnation, sediment deposition and
navigational risk were assessed. Environmental mitigation measures
might be necessary if the impacts were considered unacceptable.
Abstract: This study was conducted to investigate the efficacy
of five herbicides on narrow leaved weeds and growth and yield of
wheat. An experiment was conducted at Agronomic Research
Farm, University of Agriculture Faisalabad. The experiment was
laid out in randomized complete block designee (RCBD) with three
replications. Treatments studied were clodinafop (Topic-15 WG) at
37 g a.i. ha-1, clodinafop (Topaz-15 WG) at 45 g a.i. ha-1,
fenoxaprop-p-ethyl (Puma Super-75 EW) at 45 g a.i. ha-1,
fenoxaprop-p-ethyl (Gramicide-6.9 EW) at 85 g a.i. ha-1,
fenoxaprop-p-ethyl (Chinlima-6.9 EW) at 85 g a.i. ha-1 and weedy
check. Plots treated with fenoxaprop-p-ethyl (Puma Super-75 EW)
at 45 g a.i. ha-1 produced relatively less weed biomass, more plant
height, number of spike bearing tillers, number of grains per spike,
1000-grain weight and grain yield (4.20 t ha-1).
Abstract: Ciprofloxacin (CIP) and Carbamazepine (CBZ), nonbiodegradable pharmaceutical residues, were become emerging pollutants in several aquatic environments. The objectives of this research were to study the possibility to recover these pharmaceuticals residues from pharmaceutical wastewater by increasing the selective adsorption on synthesized functionalized porous silicate, comparing with powdered activated carbon (PAC). Hexagonal mesoporous silicate (HMS), functionalized HMSs (3- aminopropyltriethoxy, 3- mercaptopropyltrimethoxy and noctyldimethyl) were synthesized and characterized physico-chemical characteristics. Obtained adsorption kinetics and isotherms showed that 3-mercaptopropyltrimethoxy functional groups grafted on HMS provided highest CIP and CBZ adsorption capacities; however, it was still lower than that of PAC. The kinetic results were compatible with pseudo-second order. The hydrophobicity and hydrogen bonding might play a key role on the adsorption. Furthermore, the capacities were affected by varying pH values due to the strength of hydrogen bonding between targeted compounds and adsorbents. Electrostatic interaction might not affect the adsorption capacities.
Abstract: An international cooperation between educators in
Australia and the US has led to a reconceptualization of the teaching
of a library science course at Appalachian State University. The
pedagogy of Action Learning coupled with a 3D virtual learning
environment immerses students in a social constructivist learning
space that incorporates and supports interaction and reflection. The
intent of this study was to build a bridge between theory and practice
by providing students with a tool set that promoted personal and
social reflection, and created and scaffolded a community of practice.
Besides, action learning is an educational process whereby the fifty
graduate students experienced their own actions and experience to
improve performance.
Abstract: Polyurethanes (PURs) are very versatile polymeric
materials with a wide range of physical and chemical properties.
PURs have desirable properties such as high abrasion resistance, tear
strength, shock absorption, flexibility and elasticity. Although they
have relatively poor thermal stability, this can be improved by using
treated clay. Polyurethane/clay nanocomposites have been
synthesized from renewable sources. A polyol for the production of
polyurethane by reaction with an isocyanate was obtained by the
synthesis of palm oil-based oleic acid with glycerol. Dodecylbenzene
sulfonic acid (DBSA) was used as catalyst and emulsifier. The
unmodified clay (kunipia-F) was treated with cetyltrimethyl
ammonium bromide (CTAB-mont) and octadodecylamine (ODAmont).
The d-spacing in CTAB-mont and ODA-mont were 1.571 nm
and 1.798 nm respectively and larger than that of the pure-mont
(1.142 nm). The organoclay was completely intercalated in the
polyurethane, as confirmed by a wide angle x-ray diffraction
(WAXD) pattern.
The results showed that adding clay demonstrated better thermal
stability in comparison with the virgin polyurethane. Onset
degradation of pure PU is at 200oC, and is lower than that of the
CTAB-mont PU and ODA-mont PU which takes place at about
318oC and 330oC, respectively. The mechanical properties (including
the dynamic mechanical properties) of pure polyurethane (PU) and
PU/clay nanocomposites, were measured. The modified organoclay
had a remarkably beneficial effect on the strength and elongation at
break of the nanocomposites, which both increased with increasing
clay content with the increase of the tensile strength of more than
214% and 267% by the addition of only 5 wt% of the
montmorillonite CTAB-mont PU and ODA-mont PU, respectively.
Abstract: In this paper, an ultra low power and low jitter 12bit
CMOS digitally controlled oscillator (DCO) design is presented.
Based on a ring oscillator implemented with low power Schmitt
trigger based inverters. Simulation of the proposed DCO using 32nm
CMOS Predictive Transistor Model (PTM) achieves controllable
frequency range of 550MHz~830MHz with a wide linearity and high
resolution. Monte Carlo simulation demonstrates that the time-period
jitter due to random power supply fluctuation is under 31ps and the
power consumption is 0.5677mW at 750MHz with 1.2V power
supply and 0.53-ps resolution. The proposed DCO has a good
robustness to voltage and temperature variations and better linearity
comparing to the conventional design.
Abstract: The results obtained after incorporating the competence “creativity" to the subject Technical Drawing of the first course of the Degree in Forestry, Technical University of Madrid, are presented in this study.At first, learning activities which could serve two functions at the same time -developing students- creativity and developing other specific competences of the subject- were considered. Besides, changes in the assessment procedure were made and a method which analyzes two aspects of the assessment of the competence creativity was established. On the one hand, the products are evaluated by analyzing the outcomes obtained by students in the essays suggested and by establishing a parameter to assess the creativity expressed in those essays. On the other, an assessment of the student is directly carried out through a psychometric test which has been previously chosen by the team.Moreover, these results can be applied to similar or could be of general application.
Abstract: Genetic algorithms (GAs) have been widely used for
global optimization problems. The GA performance depends highly
on the choice of the search space for each parameter to be optimized.
Often, this choice is a problem-based experience. The search space
being a set of potential solutions may contain the global optimum
and/or other local optimums. A bad choice of this search space
results in poor solutions. In this paper, our approach consists in
extending the search space boundaries during the GA optimization,
only when it is required. This leads to more diversification of GA
population by new solutions that were not available with fixed search
space boundaries. So, these dynamic search spaces can improve the
GA optimization performances. The proposed approach is applied to
power system stabilizer optimization for multimachine power system
(16-generator and 68-bus). The obtained results are evaluated and
compared with those obtained by ordinary GAs. Eigenvalue analysis
and nonlinear system simulation results show the effectiveness of the
proposed approach to damp out the electromechanical oscillation and
enhance the global system stability.
Abstract: Industrial surveys shows that manufacturing
companies define the qualities of thermal removing process based on
the dimension and physical appearance of the cutting material
surface. Therefore, the roughness of the surface area of the material
cut by the plasma arc cutting process and the rate of the removed
material by the manual plasma arc cutting machine was importantly
considered. Plasma arc cutter Selco Genesis 90 was used to cut
Standard AISI 1017 Steel of 200 mm x100 mm x 6 mm manually
based on the selected parameters setting. The material removal rate
(MRR) was measured by determining the weight of the specimens
before and after the cutting process. The surface roughness (SR)
analysis was conducted using Mitutoyo CS-3100 to determine the
average roughness value (Ra). Taguchi method was utilized to
achieve optimum condition for both outputs studied. The
microstructure analysis in the region of the cutting surface is
performed using SEM. The results reveal that the SR values are
inversely proportional to the MRR values. The quality of the surface
roughness depends on the dross peak that occurred after the cutting
process.
Abstract: In determining the electromagnetic properties of
magnetic materials, hysteresis modeling is of high importance. Many
models are available to investigate those characteristics but they tend
to be complex and difficult to implement. In this paper a new
qualitative hysteresis model for ferromagnetic core is presented,
based on the function approximation capabilities of adaptive neuro
fuzzy inference system (ANFIS). The proposed ANFIS model
combined the neural network adaptive capabilities and the fuzzy
logic qualitative approach can restored the hysteresis curve with a
little RMS error. The model accuracy is good and can be easily
adapted to the requirements of the application by extending or
reducing the network training set and thus the required amount of
measurement data.
Abstract: the purpose of this research is to identify and clarify
factors which have positive effect among user satisfaction and their
social networking through websites. The examined factors in this
research are; innovation, ease of use, trustworthy and customer
support which are defined as satisfaction factors. To obtain reliable
research approaches and to have better result in this research four
hypothesizes used to test. This hypothesis testing has been done by
correlation, regression and test of normality by using “SPSS16" also
the data which was analyzed by this software. this data was gathered
from prepaid questionnaire.
Abstract: This paper addresses linear quadratic regulation (LQR)
for variable speed variable pitch wind turbines. Because of the
inherent nonlinearity of wind turbine, a set of operating conditions is
identified and then a LQR controller is designed for each operating
point. The feedback controller gains are then interpolated linearly to
get control law for the entire operating region. Besides, the
aerodynamic torque and effective wind speed are estimated online to
get the gain-scheduling variable for implementing the controller. The
potential of the method is verified through simulation with the help of
MATLAB/Simulink and GH Bladed. The performance and
mechanical load when using LQR are also compared with that when
using PI controller.
Abstract: Robust nonlinear integrated navigation of GPS and
low cost MEMS is a hot topic of research these days. A robust filter
is required to cope up with the problem of unpredictable
discontinuities and colored noises associated with low cost sensors.
H∞ filter is previously used in Extended Kalman filter and Unscented
Kalman filter frame. Unscented Kalman filter has a problem of
Cholesky matrix factorization at each step which is a very unstable
operation. To avoid this problem in this research H∞ filter is
designed in Square root Unscented filter framework and found 50%
more robust towards increased level of colored noises.
Abstract: The paper presents the design of a mini-UAV attitude
controller using the backstepping method. Starting from the nonlinear
dynamic equations of the mini-UAV, by using the backstepping
method, the author of this paper obtained the expressions of the
elevator, rudder and aileron deflections, which stabilize the UAV, at
each moment, to the desired values of the attitude angles. The attitude
controller controls the attitude angles, the angular rates, the angular
accelerations and other variables that describe the UAV longitudinal
and lateral motions. To design the nonlinear controller, by using the
backstepping technique, the nonlinear equations and the Lyapunov
analysis have been directly used. The designed controller has been
implemented in Matlab/Simulink environment and its effectiveness
has been tested with a campaign of numerical simulations using data
from the UAV flight tests. The obtained results are very good and
they are better than the ones found in previous works.
Abstract: It is important for an autonomous mobile robot to know
where it is in any time in an indoor environment. In this paper, we
design a relative self-localization algorithm. The algorithm compare
the interest point in two images and compute the relative displacement
and orientation to determent the posture. Firstly, we use the SURF
algorithm to extract the interest points of the ceiling. Second, in order
to reduce amount of calculation, a replacement SURF is used to extract
orientation and description of the interest points. At last, according to
the transformation of the interest points in two images, the relative
self-localization of the mobile robot will be estimated greatly.
Abstract: This work deals with the design of the robotic assembly
system for the roller clamps. The task is characterized by high speed,
high yield and safety engagement. This paper describes the design of
different parts of an automated high speed machine to assemble the
parts of roller clamps. The roller clamp robotic assembly system
performs various processes in the assembly line which include clamp
body and roller feeding, inserting the roller into the clamp body, and
dividing the rejected clamp and successfully assembled clamp into
their own tray. The electrical/electronics design of the machine is
discussed. The target is to design a cost effective, minimum
maintenance and high speed machine for the industry applications.