Abstract: This paper presents the experimental results of silicone rubber outdoor polymer insulators in salt fog ageing test based on IEC 61109. Specimens made ofHTV silicone rubber with ATH content having three different configurations, straight shedsalternated sheds, and incline and alternate sheds, were tested continuously 1000 hrs.in artificial salt fog chamber. Contamination level, reduction of hydrophobicity and hardness measurement were used as physical damaged inspection techniques to evaluate degree of surface deterioration. In addition, chemical changing of tested specimen surface was evaluated by ATR-FTIRto confirm physical damaged inspection. After 1000 hrs.of salt fog test, differences in degree of surface deterioration were observed on all tested specimens. Physical damaged inspection and chemical analysis results confirmed the experimental results as well.
Abstract: In this work, we perform numerical simulation of fluid
mixing in a floor-grooved micro-channel with wavy sidewalls which
may impose perturbation on the helical flow induced by the slanted
grooves on the channel floor. The perturbation is caused by separation
vortices in the recesses of the wavy-walled channel as the Reynolds
number is large enough. The results show that the effects of the wavy
sidewalls of the present micromixer on the enhancement of fluid
mixing increase with the increase of Reynolds number. The degree of
mixing increases with the increase of the corrugation angle, until the
angle is greater than 45 degrees. Besides, the pumping pressure of the
micromixer increases with the increase of the corrugation angle
monotonically. Therefore, we would suggest setting the corrugation
angle of the wavy sidewalls to be 45 degrees.
Abstract: Breastfeeding has been receiving much attention of late. Prolonged sitting for breastfeeding often results in back pain of the mothers. This paper reports the findings of a study on the effect of some factors, especially lumbar support, on back pain of breastfeeding mothers. The results showed that the use of lumbar support can reduce back pain of breastfeeding mothers significantly. Back pain was found to increase with breastfeeding time and the rate of increase was lower when lumbar supports were used. When lumbar support thickness was increased gradually from zero (no support) to 11 cm., the degree of low back pain decreased; rapidly at first, then slowly, and leveled off when the thickness reached 9 cm. Younger mothers were less prone to back pain than older mothers. The implications of the findings are discussed.
Abstract: The validity of Herzberg-s Two-Factor Theory of
Motivation was tested empirically by surveying 2372 chemical fiber
employees in 2012. In the valid sample of 1875 respondents, the
degree of overall job satisfaction was more than moderate. The most
highly valued components of job satisfaction were: “corporate image,"
“collaborative working atmosphere," and “supervisor-s expertise";
whereas the lowest mean score was 34.65 for “job rotation and
promotion." The top three job retention options rated by the
participants were “good image of the enterprise," “good
compensation," and “workplace is close to my residence." The overall
evaluation of the level of thriving facilitation workplace reached
almost to “mostly agree." For those participants who chose at least
one motivator as their job retention options had significantly greater
job satisfaction than those who chose only hygiene factors as their
retention options. Therefore, Herzberg-s Two-Factor Theory of
Motivation was proven valid in this study.
Abstract: This paper presents the control performance of a high-precision positioning device using the hybrid actuator composed of a piezoelectric (PZT) actuator and a voice-coil motor (VCM). The combined piezo-VCM actuator features two main characteristics: a large operation range due to long stroke of the VCM, and high precision and heavy load positioning ability due to PZT impact force. A one-degree-of-freedom (DOF) experimental setup was configured to examine the fundamental characteristics, and the control performance was effectively demonstrated by using a switching controller. In rough positioning state, an integral variable structure controller (IVSC) was used for the VCM to conduct long range of operation; in precision positioning state, an impact force controller (IFC) for the PZT actuator coupled with presliding states of the sliding table was used to obtain high-precision position control and achieve both forward and backward actuations. The experimental results showed that the sliding table having a mass of 881g and with a preload of 10 N was successfully positioned within the positioning accuracy of 10 nm in both forward and backward position controls.
Abstract: This paper presents an approach based on the
adoption of a distributed cognition framework and a non parametric
multicriteria evaluation methodology (DEA) designed specifically to
compare e-commerce websites from the consumer/user viewpoint. In
particular, the framework considers a website relative efficiency as a
measure of its quality and usability. A website is modelled as a black
box capable to provide the consumer/user with a set of
functionalities. When the consumer/user interacts with the website to
perform a task, he/she is involved in a cognitive activity, sustaining a
cognitive cost to search, interpret and process information, and
experiencing a sense of satisfaction. The degree of ambiguity and
uncertainty he/she perceives and the needed search time determine
the effort size – and, henceforth, the cognitive cost amount – he/she
has to sustain to perform his/her task. On the contrary, task
performing and result achievement induce a sense of gratification,
satisfaction and usefulness. In total, 9 variables are measured,
classified in a set of 3 website macro-dimensions (user experience,
site navigability and structure). The framework is implemented to
compare 40 websites of businesses performing electronic commerce
in the information technology market. A questionnaire to collect
subjective judgements for the websites in the sample was purposely
designed and administered to 85 university students enrolled in
computer science and information systems engineering
undergraduate courses.
Abstract: In this paper we consider a one-dimensional random
geometric graph process with the inter-nodal gaps evolving according
to an exponential AR(1) process. The transition probability matrix
and stationary distribution are derived for the Markov chains concerning
connectivity and the number of components. We analyze the
algorithm for hitting time regarding disconnectivity. In addition to
dynamical properties, we also study topological properties for static
snapshots. We obtain the degree distributions as well as asymptotic
precise bounds and strong law of large numbers for connectivity
threshold distance and the largest nearest neighbor distance amongst
others. Both exact results and limit theorems are provided in this
paper.
Abstract: Mapping between local and global coordinates is an
important issue in finite element method, as all calculations are
performed in local coordinates. The concern arises when subparametric
are used, in which the shape functions of the field variable
and the geometry of the element are not the same. This is particularly
the case for C* elements in which the extra degrees of freedoms
added to the nodes make the elements sub-parametric. In the present
work, transformation matrix for C1* (an 8-noded hexahedron
element with 12 degrees of freedom at each node) is obtained using
equivalent C0 elements (with the same number of degrees of
freedom). The convergence rate of 8-noded C1* element is nearly
equal to its equivalent C0 element, while it consumes less CPU time
with respect to the C0 element. The existence of derivative degrees
of freedom at the nodes of C1* element along with excellent
convergence makes it superior compared with it equivalent C0
element.
Abstract: Optimizing equipment selection in heavy earthwork
operations is a critical key in the success of any construction project.
The objective of this research incentive was geared towards
developing a computer model to assist contractors and construction
managers in estimating the cost of heavy earthwork operations.
Economical operation analysis was conducted for an equipment fleet
taking into consideration the owning and operating costs involved in
earthwork operations. The model is being developed in a Microsoft
environment and is capable of being integrated with other estimating
and optimization models. In this study, Caterpillar® Performance
Handbook [5] was the main resource used to obtain specifications of
selected equipment. The implementation of the model shall give
optimum selection of equipment fleet not only based on cost
effectiveness but also in terms of versatility. To validate the model, a
case study of an actual dam construction project was selected to
quantify its degree of accuracy.
Abstract: The purpose of this article is to analyze the
degree of concentration in the banking market in EU member
states as well as to determine the impact of the length of EU
membership on the degree of concentration. In that sense
several analysis were conducted, specifically, panel analysis,
calculation of correlation coefficient and regression analysis of
the impact of the length of EU membership on the degree of
concentration. Panel analysis was conducted to determine
whether there is a similar trend of concentration in three
groups of countries - countries with a low, moderate and high
level of concentration. The conducted panel analysis showed
that in EU countries with a moderate level of concentration,
the level of concentration decreases. The calculation of
correlation showed that, to some extent, with other influential
factors, the length of EU membership negatively affects the
market concentration of the banking market. Using the
regression analysis for investigation of the influence of the
length of EU membership on the level of concentration in the
banking sector in a particular country, the results reveal that
there is a negative effect of the length in EU membership on
market concentration, although it is not significantly influential
variable.
Abstract: This paper tests the level of market integration between Malaysia and Singapore stock markets with the world market. Kalman Filter (KF) methodology is used on the International Capital Asset Pricing Model (ICAPM) and the pricing errors estimated within the framework of ICAPM are used as a measure of market integration or segmentation. The advantage of the KF technique is that it allows for time-varying coefficients in estimating ICAPM and hence able to capture the varying degree of market integration. Empirical results show clear evidence of varying degree of market integration for both case of Malaysia and Singapore. Furthermore, the results show that the changes in the level of market integration are found to coincide with certain economic events that have taken placed. The findings certainly provide evidence on the practicability of the KF technique to estimate stock markets integration. In the comparison between Malaysia and Singapore stock market, the result shows that the trends of the market integration indices for Malaysia and Singapore look similar through time but the magnitude is notably different with the Malaysia stock market showing greater degree of market integration. Finally, significant evidence of varying degree of market integration shows the inappropriate use of OLS in estimating the level of market integration.
Abstract: This paper makes an attempt to solve the problem of
searching and retrieving of similar MRI photos via Internet services
using morphological features which are sourced via the original
image. This study is aiming to be considered as an additional tool of
searching and retrieve methods. Until now the main way of the
searching mechanism is based on the syntactic way using keywords.
The technique it proposes aims to serve the new requirements of
libraries. One of these is the development of computational tools for
the control and preservation of the intellectual property of digital
objects, and especially of digital images. For this purpose, this paper
proposes the use of a serial number extracted by using a previously
tested semantic properties method. This method, with its center being
the multi-layers of a set of arithmetic points, assures the following
two properties: the uniqueness of the final extracted number and the
semantic dependence of this number on the image used as the
method-s input. The major advantage of this method is that it can
control the authentication of a published image or its partial
modification to a reliable degree. Also, it acquires the better of the
known Hash functions that the digital signature schemes use and
produces alphanumeric strings for cases of authentication checking,
and the degree of similarity between an unknown image and an
original image.
Abstract: This paper deals with a delayed single population model on time scales. With the assistance of coincidence degree theory, sufficient conditions for existence of periodic solutions are obtained. Furthermore, the better estimations for bounds of periodic solutions are established.
Abstract: In recent years application of natural antimicrobials
instead of conventional ones, due to their hazardous effects on health,
has got serious attentions. On the basis of the results of different
studies, chitosan, a natural bio-degradable and non-toxic
biopolysaccharide derived from chitin, has potential to be used as a
natural antimicrobial. Chitosan has exhibited high antimicrobial
activity against a wide variety of pathogenic and spoilage
microorganisms, including fungi, and Gram-positive and Gramnegative
bacteria. The antimicrobial action is influenced by intrinsic
factors such as the type of chitosan, the degree of chitosan
polymerization and extrinsic factors such as the microbial organism,
the environmental conditions and presence of the other components.
The use of chitosan in food systems should be based on sufficient
knowledge of the complex mechanisms of its antimicrobial mode of
action. In this article we review a number of studies on the
investigation of chitosan antimicrobial properties and application of
them in culture and food mediums.
Abstract: The results obtained after incorporating the competence “creativity" to the subject Technical Drawing of the first course of the Degree in Forestry, Technical University of Madrid, are presented in this study.At first, learning activities which could serve two functions at the same time -developing students- creativity and developing other specific competences of the subject- were considered. Besides, changes in the assessment procedure were made and a method which analyzes two aspects of the assessment of the competence creativity was established. On the one hand, the products are evaluated by analyzing the outcomes obtained by students in the essays suggested and by establishing a parameter to assess the creativity expressed in those essays. On the other, an assessment of the student is directly carried out through a psychometric test which has been previously chosen by the team.Moreover, these results can be applied to similar or could be of general application.
Abstract: An experimental investigation was performed on pulp
liquid flow in straight ducts with a square cross section. Fully
developed steady flow was visualized and the fiber concentration was
obtained using a light-section method developed by the author et al.
The obtained results reveal quantitatively, in a definite form, the
distribution of the fiber concentration. From the results and
measurements of pressure loss, it is found that the flow characteristics
of pulp liquid in ducts can be classified into five patterns. The
relationships among the distributions of mean and fluctuation of fiber
concentration, the pressure loss and the flow velocity are discussed,
and then the features for each pattern are extracted. The degree of
nonuniformity of the fiber concentration, which is indicated by the
standard deviation of its distribution, is decreased from 0.3 to 0.05
with an increase in the velocity of the tested pulp liquid from 0.4 to
0.8%.
Abstract: The purpose of this study attempts to emphasize the factors relating to intra-family relationships (order point of view) on violence against the women, For this purpose a survey technique on the sample size amounted 100 women of married of city of Ilam in country of Iran were considered. For measurement of violence against the women , the CTS scaled has been used .violence against the women be measured in four dimension ( emotional violence, psycho violence, physical violence, neglect violence). highest violence was related to emotional violence and after are as follow respectively : physical violence and neglect violence. The results showed that women have experienced the violence more than once during the last year, degree of order in family is high. Explanation result indicated that the order variables in family including collective thinking, empathy and communal co-circumstance have significant effects on violence against the women. Via multiple regression analysis variables of empathy, religious tenet and education of husband had significant effect on violence against women. In other words relationships among family effect on violence in family.
Abstract: Adhesion strength of exterior or interior coating of
steel pipes is too important. Increasing of coating adhesion on
surfaces can increase the life time of coating, safety factor of
transmitting line pipe and decreasing the rate of corrosion and costs.
Preparation of steel pipe surfaces before doing the coating process is
done by shot and grit blasting. This is a mechanical way to do it.
Some effective parameters on that process, are particle size of
abrasives, distance to surface, rate of abrasive flow, abrasive physical
properties, shapes, selection of abrasive, kind of machine and its
power, standard of surface cleanness degree, roughness, time of
blasting and weather humidity. This search intended to find some
better conditions which improve the surface preparation, adhesion
strength and corrosion resistance of coating. So, this paper has
studied the effect of varying abrasive flow rate, changing the
abrasive particle size, time of surface blasting on steel surface
roughness and over blasting on it by using the centrifugal blasting
machine. After preparation of numbers of steel samples (according to
API 5L X52) and applying epoxy powder coating on them, to
compare strength adhesion of coating by Pull-Off test. The results
have shown that, increasing the abrasive particles size and flow rate,
can increase the steel surface roughness and coating adhesion
strength but increasing the blasting time can do surface over blasting
and increasing surface temperature and hardness too, change,
decreasing steel surface roughness and coating adhesion strength.
Abstract: The expression of LFA-1 diverges from the
physiological condition, thus active targeting carrier can provide the
benefits from difference into LFA-1 expression in various conditions.
Here, the selectivity of cIBR-conjugated nanoparticles (cIBR-NPs),
in terms of uptake, was investigated using PBMCs, Mixed PBMCMolt-
3 cells and Molt-3 cells. The expressions of LFA-1 on Molt-3
cells, from flow cytometry and Western blot, possessed the highest
level whereas PBMCs showed the lowest level. The kinetic uptake
profiles of cIBR-NPs were obtained by flow cytometry, which the
degree of cellular uptake presented a similar trend with the level of
LFA-1 indicating the influence of LFA-1 expression on the cellular
uptake of cIBR-NPs. The conformation of LFA-1 had a slight effect
on the cellular uptake of cIBR-NPs. Overall we demonstrated that
cIBR-NPs enhanced cellular uptake and improved the selectivity of
drug carriers to LFA-1 on the leukemia cells, which related with the
order of LFA-1 expression.
Abstract: In this paper, by applying Mawhin-s continuation theorem of coincidence degree theory, we study the existence of almost periodic solutions for neural multi-delay logarithmic population model and obtain one sufficient condition for the existence of positive almost periodic solution for the above equation. An example is employed to illustrate our result.