Abstract: Wastages such as grated coconut meat, spent tea and used sugarcane had contributed negative impacts to the environment. Vermicomposting method is fully utilized to manage the wastes towards a more sustainable approach. The worms that are used in the vermicomposting are Eisenia foetida and Eudrillus euginae. This research shows that the vermicompost of wastages has voltage of electrical energy and is able to light up the Light-Emitting Diode (LED) device. Based on the experiment, the use of replicated and double compartments of the component will produce double of voltage. Hence, for conclusion, this harmless and low cost technology of vermicompost can act as a dry cell in order to reduce the usage of hazardous chemicals that can contaminate the environment.
Abstract: This research paper presents some methods to assess the performance of Wigner Ville Distribution for Time-Frequency representation of non-stationary signals, in comparison with the other representations like STFT, Spectrogram etc. The simultaneous timefrequency resolution of WVD is one of the important properties which makes it preferable for analysis and detection of linear FM and transient signals. There are two algorithms proposed here to assess the resolution and to compare the performance of signal detection. First method is based on the measurement of area under timefrequency plot; in case of a linear FM signal analysis. A second method is based on the instantaneous power calculation and is used in case of transient, non-stationary signals. The implementation is explained briefly for both methods with suitable diagrams. The accuracy of the measurements is validated to show the better performance of WVD representation in comparison with STFT and Spectrograms.
Abstract: This paper deals with the modeling and the evaluation of a multiplicative phase noise influence on the bit error ratio in a general space communication system. Our research is focused on systems with multi-state phase shift keying modulation techniques and it turns out, that the phase noise significantly affects the bit error rate, especially for higher signal to noise ratios. These results come from a system model created in Matlab environment and are shown in a form of constellation diagrams and bit error rate dependencies. The change of a user data bit rate is also considered and included into simulation results. Obtained outcomes confirm theoretical presumptions.
Abstract: Network management techniques have long been of
interest to the networking research community. The queue size plays
a critical role for the network performance. The adequate size of the
queue maintains Quality of Service (QoS) requirements within
limited network capacity for as many users as possible. The
appropriate estimation of the queuing model parameters is crucial for
both initial size estimation and during the process of resource
allocation. The accurate resource allocation model for the
management system increases the network utilization. The present
paper demonstrates the results of empirical observation of memory
allocation for packet-based services.
Abstract: Developments in scientific and technical area cause to use new methods and techniques in education, as is the case in all fields. Especially, the internet contributes a variety of new methods to design virtual and real time laboratory applications in education. In this study, a real time virtual laboratory is designed and implemented for analog and digital communications laboratory experiments by using Lab VIEW program for Marmara University Electronics-Communication Department. In this application, students can access the virtual laboratory web site and perform their experiments without any limitation of time and location so as the students can observe the signals by changing the parameters of the experiment and evaluate the results.
Abstract: Light is one of the most important qualitative and
symbolic factors and has a special position in architecture and urban
development in regard to practical function. The main function of
light, either natural or artificial, is lighting up the environment and
the constructional forms which is called lighting. However, light is
used to redefine the urban spaces by architectural genius with regard
to three aesthetic, conceptual and symbolic factors. In architecture
and urban development, light has a function beyond lighting up the
environment, and the designers consider it as one of the basic
components. The present research aims at studying the function of
light and color in architectural view and their effects in buildings.
Abstract: While compressing text files is useful, compressing
still image files is almost a necessity. A typical image takes up much
more storage than a typical text message and without compression
images would be extremely clumsy to store and distribute. The
amount of information required to store pictures on modern
computers is quite large in relation to the amount of bandwidth
commonly available to transmit them over the Internet and
applications. Image compression addresses the problem of reducing
the amount of data required to represent a digital image. Performance
of any image compression method can be evaluated by measuring the
root-mean-square-error & peak signal to noise ratio. The method of
image compression that will be analyzed in this paper is based on the
lossy JPEG image compression technique, the most popular
compression technique for color images. JPEG compression is able to
greatly reduce file size with minimal image degradation by throwing
away the least “important" information. In JPEG, both color
components are downsampled simultaneously, but in this paper we
will compare the results when the compression is done by
downsampling the single chroma part. In this paper we will
demonstrate more compression ratio is achieved when the
chrominance blue is downsampled as compared to downsampling the
chrominance red in JPEG compression. But the peak signal to noise
ratio is more when the chrominance red is downsampled as compared
to downsampling the chrominance blue in JPEG compression. In
particular we will use the hats.jpg as a demonstration of JPEG
compression using low pass filter and demonstrate that the image is
compressed with barely any visual differences with both methods.
Abstract: Demand of energy is increasing faster than the
generation. It leads shortage of power in all sectors of society. At
peak hours this shortage is higher. Unless we utilize energy efficient
technology, it is very difficult to minimize the shortage of energy. So
energy efficiency program and energy conservation has an important
role. Energy efficient technologies are cost intensive hence it is
always not possible to implement in country like India. In the recent
study, an educational building with operating hours from 10:00 a.m.
to 05:00 p.m. has been selected to quantify the possibility of lighting
energy conservation. As the operating hour is in daytime, integration
of daylight with artificial lighting system will definitely reduce the
lighting energy consumption. Moreover the initial investment has
been given priority and hence the existing lighting installation was
unaltered. An automatic controller has been designed which will be
operated as a function of daylight through windows and the lighting
system of the room will function accordingly. The result of the study
of integrating daylight gave quite satisfactory for visual comfort as
well as energy conservation.
Abstract: A spectrophotometric method was developed for simultaneous quantification of pseudoephedrine hydrochloride (PSE) triprolidine hydrochloride (TRI) using second derivative method (zero-crossing technique). The second derivative amplitudes of PSE and TRI were measured at 271 and 321 nm, respectively. The calibration curves were linear in the range of 200 to 1,000 g/ml for PSE and 10 to 50 g/ml for TRI. The method was validated for specificity, accuracy, precision, limit of detection and limit of quantitation. The proposed method was applied to the assaying and dissolution of PSE and TRI in commercial tablets without any chemical separation. The results were compared with those obtained by the official USP31 method and statistical tests showed that there is no significant between the methods at 95% confidence level. The proposed method is simple, rapid and suitable for the routine quality control application. KeywordsTriprolidine, Pseudoephedrine, Derivative spectrophotometry, Dissolution testing.
Abstract: A system for market identification (SMI) is presented.
The resulting representations are multivariable dynamic demand
models. The market specifics are analyzed. Appropriate models and
identification techniques are chosen. Multivariate static and dynamic
models are used to represent the market behavior. The steps of the
first stage of SMI, named data preprocessing, are mentioned. Next,
the second stage, which is the model estimation, is considered in more
details. Stepwise linear regression (SWR) is used to determine the
significant cross-effects and the orders of the model polynomials. The
estimates of the model parameters are obtained by a numerically stable
estimator. Real market data is used to analyze SMI performance.
The main conclusion is related to the applicability of multivariate
dynamic models for representation of market systems.
Abstract: This paper proposes an effective algorithm approach to hybrid control systems combining fuzzy logic and conventional control techniques of controlling the speed of induction motor assumed to operate in high-performance drives environment. The introducing of fuzzy logic in the control systems helps to achieve good dynamical response, disturbance rejection and low sensibility to parameter variations and external influences. Some fundamentals of the fuzzy logic control are preliminary illustrated. The developed control algorithm is robust, efficient and simple. It also assures precise trajectory tracking with the prescribed dynamics. Experimental results have shown excellent tracking performance of the proposed control system, and have convincingly demonstrated the validity and the usefulness of the hybrid fuzzy controller in high-performance drives with parameter and load uncertainties. Satisfactory performance was observed for most reference tracks.
Abstract: This paper proposes a hybrid method for eyes localization
in facial images. The novelty is in combining techniques
that utilise colour, edge and illumination cues to improve accuracy.
The method is based on the observation that eye regions have dark
colour, high density of edges and low illumination as compared
to other parts of face. The first step in the method is to extract
connected regions from facial images using colour, edge density and
illumination cues separately. Some of the regions are then removed
by applying rules that are based on the general geometry and shape
of eyes. The remaining connected regions obtained through these
three cues are then combined in a systematic way to enhance the
identification of the candidate regions for the eyes. The geometry
and shape based rules are then applied again to further remove the
false eye regions. The proposed method was tested using images from
the PICS facial images database. The proposed method has 93.7%
and 87% accuracies for initial blobs extraction and final eye detection
respectively.
Abstract: This research aims to study the lead pollution in the air of Babylon governorate that resulted generally from vehicles exhausts in addition to industrial and human activities.Vehicles number in Babylon governorate increased significantly after year 2003 that resulted with increase in lead emissions into the air.Measurement of lead emissions was done in seven stations distributed randomly in Babylon governorate. These stations where located in Industrial (Al-Sena'ay) Quarter, 60 street (near to Babylon sewer directorate), 40 Street (near to the first intersection), Al-Hashmia city, Al-Mahaweel city, , Al- Musayab city in addition to another station in Sayd Idris village belong to Abugharaq district (Agricultural station for comparison). The measured concentrations in these stations were compared with the standard limits of Environmental Protection Agency EPA (2 μg /m3). The results of this study showed that the average of lead concentrations ,in Babylon governorate during year 2010, was (3.13 μg/m3) which was greater than standard limits (2 μg/m3). The maximum concentration of lead was (6.41 μg / m3) recorded in the Industrial (Al-Sena'ay) Quarter during April month, while the minimum concentrations was (0.36 μg / m3) recorded in the agricultural station (Abugharaq) during December month.
Abstract: The paper investigates the potential of support vector
machines and Gaussian process based regression approaches to
model the oxygen–transfer capacity from experimental data of
multiple plunging jets oxygenation systems. The results suggest the
utility of both the modeling techniques in the prediction of the
overall volumetric oxygen transfer coefficient (KLa) from operational
parameters of multiple plunging jets oxygenation system. The
correlation coefficient root mean square error and coefficient of
determination values of 0.971, 0.002 and 0.945 respectively were
achieved by support vector machine in comparison to values of
0.960, 0.002 and 0.920 respectively achieved by Gaussian process
regression. Further, the performances of both these regression
approaches in predicting the overall volumetric oxygen transfer
coefficient was compared with the empirical relationship for multiple
plunging jets. A comparison of results suggests that support vector
machines approach works well in comparison to both empirical
relationship and Gaussian process approaches, and could successfully
be employed in modeling oxygen-transfer.
Abstract: The paper gives the pilot results of the project that is
oriented on the use of data mining techniques and knowledge
discoveries from production systems through them. They have been
used in the management of these systems. The simulation models of
manufacturing systems have been developed to obtain the necessary
data about production. The authors have developed the way of
storing data obtained from the simulation models in the data
warehouse. Data mining model has been created by using specific
methods and selected techniques for defined problems of production
system management. The new knowledge has been applied to
production management system. Gained knowledge has been tested
on simulation models of the production system. An important benefit
of the project has been proposal of the new methodology. This
methodology is focused on data mining from the databases that store
operational data about the production process.
Abstract: In this paper , by using fixed point theorem , upper and lower solution-s method and monotone iterative technique , we prove the existence of maximum and minimum solutions of differential equations with delay , which improved and generalize the result of related paper.
Abstract: Recent advances in wireless sensor networks have led
to many routing methods designed for energy-efficiency in wireless
sensor networks. Despite that many routing methods have been
proposed in USN, a single routing method cannot be energy-efficient
if the environment of the ubiquitous sensor network varies. We present
the controlling network access to various hosts and the services they
offer, rather than on securing them one by one with a network security
model. When ubiquitous sensor networks are deployed in hostile
environments, an adversary may compromise some sensor nodes and
use them to inject false sensing reports. False reports can lead to not
only false alarms but also the depletion of limited energy resource in
battery powered networks. The interleaved hop-by-hop authentication
scheme detects such false reports through interleaved authentication.
This paper presents a LMDD (Low energy method for data delivery)
algorithm that provides energy-efficiency by dynamically changing
protocols installed at the sensor nodes. The algorithm changes
protocols based on the output of the fuzzy logic which is the fitness
level of the protocols for the environment.
Abstract: Matrix metalloproteinase-3 (MMP3) is key member
of the MMP family, and is known to be present in coronary
atherosclerotic. Several studies have demonstrated that MMP-3
5A/6A polymorphism modify each transcriptional activity in allele
specific manner. We hypothesized that this polymorphism may play
a role as risk factor for development of coronary stenosis. The aim of
our study was to estimate MMP-3 (5A/6A) gene polymorphism on
interindividual variability in risk for coronary stenosis in an Iranian
population.DNA was extracted from white blood cells and genotypes
were obtained from coronary stenosis cases (n=95) and controls
(n=100) by PCR (polymerase chain reaction) and restriction
fragment length polymorphism techniques. Significant differences
between cases and controls were observed for MMP3 genotype
frequencies (X2=199.305, p< 0.001); the 6A allele was less
frequently seen in the control group, compared to the disease group
(85.79 vs. 78%, 6A/6A+5A/6A vs. 5A/5A, P≤0.001). These data
imply the involvement of -1612 5A/6A polymorphism in coronary
stenosis, and suggest that probably the 6A/6A MMP-3 genotype is a
genetic susceptibility factor for coronary stenosis.
Abstract: In this paper, the effect of width and height of the
model on the earthquake response in the finite element method is
discussed. For this purpose an earth dam as a soil structure under
earthquake has been considered. Various dam-foundation models are
analyzed by Plaxis, a finite element package for solving geotechnical
problems. The results indicate considerable differences in the seismic
responses.
Abstract: The present paper was concerned primarily with the
analysis, simulation of the air flow and thermal patterns in a lecture
room. The paper is devoted to numerically investigate the influence
of location and number of ventilation and air conditioning supply and
extracts openings on air flow properties in a lecture room. The work
focuses on air flow patterns, thermal behaviour in lecture room where
large number of students. The effectiveness of an air flow system is
commonly assessed by the successful removal of sensible and latent
loads from occupants with additional of attaining air pollutant at a
prescribed level to attain the human thermal comfort conditions and
to improve the indoor air quality; this is the main target during the
present paper. The study is carried out using computational fluid
dynamics (CFD) simulation techniques as embedded in the
commercially available CFD code (FLUENT 6.2). The CFD
modelling techniques solved the continuity, momentum and energy
conservation equations in addition to standard k – ε model equations
for turbulence closure.
Throughout the investigations, numerical validation is carried out by
way of comparisons of numerical and experimental results. Good
agreement is found among both predictions.